The impact of municipal solid waste management on greenhouse gas emissions in the United States

Technological advancements, environmental regulations, and emphasis on resource conservation and recovery have greatly reduced the environmental impacts of municipal solid waste (MSW) management, including emissions of greenhouse gases (GHGs). This study was conducted using a life-cycle methodology to track changes in GHG emissions during the past 25 years from the management of MSW in the United States. For the baseline year of 1974, MSW management consisted of limited recycling, combustion without energy recovery, and landfilling without gas collection or control. This was compared with data for 1980, 1990, and 1997, accounting for changes in MSW quantity, composition, management practices, and technology. Over time, the United States has moved toward increased recycling, composting, combustion (with energy recovery) and landfilling with gas recovery, control, and utilization. These changes were accounted for with historical data on MSW composition, quantities, management practices, and technological changes. Included in the analysis were the benefits of materials recycling and energy recovery to the extent that these displace virgin raw materials and fossil fuel electricity production, respectively. Carbon sinks associated with MSW management also were addressed. The results indicate that the MSW management actions taken by U.S. communities have significantly reduced potential GHG emissions despite an almost 2-fold increase in waste generation. GHG emissions from MSW management were estimated to be 36 million metric tons carbon equivalents (MMTCE) in 1974 and 8 MMTCE in 1997. If MSW were being managed today as it was in 1974, GHG emissions would be approximately 60 MMTCE.     

An economic evaluation and assessment of environmental impact of the municipal solid waste management system for Taichung City in Taiwan

Municipal solid waste management (MSWM) is an important environmental challenge and subject in urban planning. For sustainable MSWM strategies, the critical management factors to be considered include not only economic efficiency of MSW treatment but also life-cycle assessment of the environmental impact. This paper employed linear programming technique to establish optimal MSWM strategies considering economic efficiency and the air pollutant emissions during the life cycle of a MSWM system, and investigated the correlations between the economical optimization and pollutant emissions. A case study based on real-world MSW operating parameters in Taichung City is also presented. The results showed that the costs, benefits, streams of MSW, and throughputs of incinerators and landfills will be affected if pollution emission reductions are implemented in the MSWM strategies. In addition, the quantity of particulate matter is the best pollutant indicator for the MSWM system performance of emission reduction. In particular this model will assist the decision maker in drawing up a friendly MSWM strategy for Taichung City in Taiwan. Implications: Recently, life-cycle assessments of municipal solid waste management (MSWM) strategies have been given more considerations. However, what seems to be lacking is the consideration of economic factors and environmental impacts simultaneously. This work analyzed real-world data to establish optimal MSWM strategies considering economic efficiency and the air pollutant emissions during the life cycle of the MSWM system. The results indicated that the consideration of environmental impacts will affect the costs, benefits, streams of MSW, and throughputs of incinerators and landfills. This work is relevant to public discussion and may establish useful guidelines for the MSWM policies.     

An economic evaluation and assessment of environmental impact of the municipal solid waste management system for Taichung City in Taiwan

Municipal solid waste management (MSWM) is an important environmental challenge and subject in urban planning. For sustainable MSWM strategies, the critical management factors to be considered include not only economic efficiency of MSW treatment but also life-cycle assessment of the environmental impact. This paper employed linear programming technique to establish optimal MSWM strategies considering economic efficiency and the air pollutant emissions during the life cycle of a MSWM system, and investigated the correlations between the economical optimization and pollutant emissions. A case study based on real-world MSW operating parameters in Taichung City is also presented. The results showed that the costs, benefits, streams of MSW, and throughputs of incinerators and landfills will be affected if pollution emission reductions are implemented in the MSWM strategies. In addition, the quantity of particulate matter is the best pollutant indicator for the MSWM system performance of emission reduction. In particular, this model will assist the decision maker in drawing up a friendly MSWM strategy for Taichung City in Taiwan.

Implications: Recently, life-cycle assessments of municipal solid waste management (MSWM) strategies have been given more considerations. However, what seems to be lacking is the consideration of economic factors and environmental impacts simultaneously. This work analyzed real-world data to establish optimal MSWM strategies considering economic efficiency and the air pollutant emissions during the life cycle of the MSWM system. The results indicated that the consideration of environmental impacts will affect the costs, benefits, streams of MSW, and throughputs of incinerators and landfills. This work is relevant to public discussion and may establish useful guidelines for the MSWM policies.     

Optimization for municipal solid waste treatment based on energy consumption and contaminant emission

This paper analyzes the characterization of energy consumption and contaminant emissions from a municipal solid waste (MSW) treatment system that comprises transfer station, landfill site, combustion plant, composting plant, dejecta treatment station, and an integrated MSW treatment plant. The consumed energy and energy medium materials were integrated under comprehensive energy consumption (CEC) for comparison. Among typical MSW disposal methods such as combustion, composting, and landfilling, landfilling has the minimum CEC value. Installing an integrated treatment plant is the recommended MSW management method because of its lower CEC. Furthermore, this method is used to ensure process centralization. In landfill sites, a positive linear correlation was observed between the CEC and contaminant removal ratios when emitted pollutants have a certain weight coefficient. The process should utilize the minimum CEC value of 5.3702 kgce/t MSW and consider energy consumption, energy recovery, MSW components, and the equivalent of carbon dioxide emissions.     

Compromising economic cost and air pollutant emissions of municipal solid waste management strategies by fuzzy multiobjective optimization model

Municipal solid waste management (MSWM) is an important environmental challenge and subject in urban planning. A sustainable MSWM strategy should consider not only economic efficiency but also life-cycle assessment of environmental impact. This study employs the fuzzy multiobjective linear programming (FMOLP) technique to find the optimal compromise between economic optimization and pollutant emission reduction for the MSWM strategy. Taichung City in Taiwan is evaluated as a case study. The results indicate that the optimal compromise MSWM strategy can reduce significant amounts of pollutant emissions and still achieve positive net profits. Minimization of the sulfur oxide (SO_x) and nitrogen oxide (NO_x) emissions are the two major priorities in achieving this optimal compromise strategy when recyclables recovery rate is lower; however, minimization of the carbon monoxide (CO) and particulate matter (PM) emissions become priority factors when recovery rate is higher.

Implications: This paper applied the multiobjective optimization model to find the optimal compromise municipal solid waste management (MSWM) strategy, which minimizes both life-cycle operating cost and air pollutant emissions, and also to analyze the correlation between recyclables recovery rates and optimal compromise strategies. It is different from past studies, which only consider economic optimization or environmental impacts of the MSWM system. The result shows that optimal compromise MSWM strategy can achieve a net profit and reduce air pollution emission. In addition, scenario investigation of recyclables recovery rates indicates that resource recycling is beneficial for both economic optimization and air pollutant emission minimization.     

Food waste collection and recycling for value-added products: potential applications and challenges in Hong Kong

About 3600 tonnes food waste are discarded in the landfills in Hong Kong daily. It is expected that the three strategic landfills in Hong Kong will be exhausted by 2020. In consideration of the food waste management environment and community needs in Hong Kong, as well as with reference to the food waste management systems in cities such as Linköping in Sweden and Oslo in Norway, a framework of food waste separation, collection, and recycling for food waste valorization is proposed in this paper. Food waste can be packed in an optic bag (i.e., a bag in green color), while the residual municipal solid waste (MSW) can be packed in a common plastic bag. All the wastes are then sent to the refuse transfer stations, in which food waste is separated from the residual MSW using an optic sensor. On the one hand, the sorted food waste can be converted into valuable materials (e.g., compost, swine feed, fish feed). On the other hand, the sorted food waste can be sent to the proposed Organic Waste Treatment Facilities and sewage treatment works for producing biogas. The biogas can be recovered to produce electricity and city gas (i.e., heating fuel for cooking purpose). Due to the challenges faced by the value-added products in Hong Kong, the biogas is recommended to be upgraded as a biogas fuel for vehicle use. Hopefully, the proposed framework will provide a simple and effective approach to food waste separation at source and promote sustainable use of waste to resource in Hong Kong.     

The role of bio-mechanical treatments of waste in the dioxin emission inventories

PCDD/Fs are one of the most studied molecules in the world because of their toxicity. In the last years the toxicity of these compounds has been analyzed in details. For years PCDD/F inventories have pointed out the significant role of municipal solid waste (MSW) incinerators in the overall balance. Recently, thanks to new regulations on PCDD/F emissions, in a few countries this scenario is changing: it can be demonstrated that modern MSW incinerators can play a secondary role even if the percentage of MSW sent to combustion has increased. In the latest inventories an unconventional source of PCDD/F has appeared: in nineties some biogas characterizations have demonstrated that there is a release of PCDD/F from MSW sanitary landfills. In addition, the combustion of collected biogas can generate not negligible amounts of PCDD/F. A new question can be put: does the MSW contribute with other management options to the overall balance of PCDD/F? The present work points out that a detailed inventory should take into account also the PCDD/F release from bio-mechanical treatment plants (both composting and bio-drying/bio-stabilization plants). However the contribution from this option is secondary when it is compared with the one from old MSW incinerators.     

复合微生物菌剂强化堆肥技术研究

采用复合微生物菌剂对生活垃圾的接种堆肥技术进行了实验研究。通过测定堆肥过程中反应器出口O2、CO2与H2S气体浓度及对堆肥样品扫描电镜照片分析，比较了3个接种组与1个对照组中堆料中微生物总数变化、种群结构演替及堆肥腐熟速度。试验结果表明，在原料成分为：生活垃圾／成熟堆肥=80／20，有机物约为60％，初始含水率为55％，初始C／N-30时，对于不同接种量的复合微生物接种系统堆料中分别接种0．2％、0．3％、0．5％(质量百分含量)，与加入0．3％灭活菌的对照组进行对比实验，接种复合微生物菌剂堆肥系统不仅微生物总数高于对照组，而且其种群结构合理，能明显提高堆肥效率，有效控制臭气的产生，提高堆肥腐熟度。     

Fuel consumption, emissions estimation, and emissions cost estimates using global positioning data

The methodology laid out in this paper shows that typical operational data from vehicle fleets monitored by a global positioning system (GPS) can be used to estimate heavy-duty diesel vehicle (HDDV) emissions, thereby enabling waste managers and governing bodies to internalize the responsibility for socioenvironmental costs traditionally absorbed by external parties. Although municipal solid waste (MSW) collection vehicles are the subjects of this particular study, the methodology presented here can be applied to any fleet of vehicles monitored by GPS. This study indicates that MSW collection trucks may be considerably less fuel efficient in the field than published values for HDDV fuel efficiency suggest. The average fuel efficiency of one MSW collection truck was estimated as 0.90 +/- 0.44 km/L (2.12 +/- 1.03 mi/gal). This same truck would generate approximately 42 metric tons of CO2 equivalents/yr, which is comparable to the greenhouse gas emissions of a large sport utility vehicle driving six times the distance, in town, for a year. In terms of the impacts such emissions have, projections for the monetary cost of emissions are available but highly variable. They suggest that the external monetary costs of emissions range between 6 and 39% of the annual fuel costs for the studied MSW collection truck. The results of this study indicate a need for further research into valuation of the hidden, external costs of emissions, borne by local and global socioecological communities. The possible implications of this result include poorly advised fleet procurement decisions and underestimation of MSW collection fleet emissions.     

Greenhouse Gas Mitigation-Induced Rough-Interval Programming for Municipal Solid Waste Management

Abstract

A greenhouse gas (GHG) mitigation-induced rough-interval programming model is proposed in this study. Components of GHG emission and environmental pollution control are incorporated into the objective function and a series of relevant constraints. To explicitly examine more complexities existing in many parameters, rough intervals are also communicated into the modeling framework. The proposed model presents satisfactory capabilities in analyzing complicated interrelationships among municipal solid waste (MSW) management, climate-change impact, and environmental pollution control. It can also provide optimal allocation schemes and facilitate decision-makers regulating environmentally sustainable strategies. The developed model is then applied to a case study for demonstrating its applicability. Two representative scenarios (relatively representing two potential management policies that may be implemented in the future years) are considered. The results indicate that the developed model presents advantages in mitigating GHG emissions and the associated climate-change impact. The comparison between the GHG mitigation-induced model with and without rough-interval parameters is also investigated. Completely different solutions of the two models imply the significant impact of dual-uncertain information on the system, which can hardly be addressed through the existing optimization approaches.     

Municipal solid waste management planning for Xiamen City,China: a stochastic fractional inventory-theory-based approach

In this study, a stochastic fractional inventory-theory-based waste management planning (SFIWP) model was developed and applied for supporting long-term planning of the municipal solid waste (MSW) management in Xiamen City, the special economic zone of Fujian Province, China. In the SFIWP model, the techniques of inventory model, stochastic linear fractional programming, and mixed-integer linear programming were integrated in a framework. Issues of waste inventory in MSW management system were solved, and the system efficiency was maximized through considering maximum net-diverted wastes under various constraint-violation risks. Decision alternatives for waste allocation and capacity expansion were also provided for MSW management planning in Xiamen. The obtained results showed that about 4.24 × 10⁶ t of waste would be diverted from landfills when p _i is 0.01, which accounted for 93% of waste in Xiamen City, and the waste diversion per unit of cost would be 26.327 × 10³ t per $10⁶. The capacities of MSW management facilities including incinerators, composting facility, and landfills would be expanded due to increasing waste generation rate.     

城市垃圾预处理改善焚烧特性的探讨

针对目前我国城市垃圾的高水分、低热值的特性,提出了2种改善城市垃圾焚烧特性的有效措施:生物质垃圾源分类和生物干燥.在我国建立生物质垃圾源分类体系,将生物质垃圾源头分类后,剩余垃圾的热值可以提高约50%～120%,已适合直接入炉焚烧,同时分离出来的生物质垃圾也更易于好氧堆肥或厌氧消化.另外一项技术措施是在焚烧前利用生物干燥技术,降低城市垃圾的水分含量,提高入炉垃圾的热值,这种方法主要是利用生物反应热来干燥城市生活垃圾,只需要在垃圾投入焚烧炉前增加一个预处理步骤,不必改变目前的垃圾收运体系,而且进行生物干燥后的垃圾更易于分选其中的可回收物质.     

Source separation of municipal solid waste: The effects of different separation methods and citizens’ inclination—case study of Changsha,China

A case study on the source separation of municipal solid waste (MSW) was performed in Changsha, the capital city of Hunan Province, China. The objective of this study is to analyze the effects of different separation methods and compare their effects with citizens’ attitudes and inclination. An effect evaluation method based on accuracy rate and miscellany rate was proposed to study the performance of different separation methods. A large-scale questionnaire survey was conducted to determine citizens’ attitudes and inclination toward source separation. Survey result shows that the vast majority of respondents hold consciously positive attitudes toward participation in source separation. Moreover, the respondents ignore the operability of separation methods and would rather choose the complex separation method involving four or more subclassed categories. For the effects of separation methods, the site experiment result demonstrates that the relatively simple separation method involving two categories (food waste and other waste) achieves the best effect with the highest accuracy rate (83.1%) and the lowest miscellany rate (16.9%) among the proposed experimental alternatives. The outcome reflects the inconsistency between people’s environmental awareness and behavior. Such inconsistency and conflict may be attributed to the lack of environmental knowledge. Environmental education is assumed to be a fundamental solution to improve the effect of source separation of MSW in Changsha. Important management tips on source separation, including the reformation of the current pay-as-you-throw (PAYT) system, are presented in this work.

Implications: A case study on the source separation of municipal solid waste was performed in Changsha. An effect evaluation method based on accuracy rate and miscellany rate was proposed to study the performance of different separation methods. The site experiment result demonstrates that the two-category (food waste and other waste) method achieves the best effect. The inconsistency between people’s inclination and the effect of source separation exists. The proposed method can be expanded to other cities to determine the most effective separation method during planning stages or to evaluate the performance of running source separation systems.     

Biodegradation of organic matters from mixed unshredded municipal solid waste through air convection before landfilling

Landfilling is a dominant municipal solid waste (MSW) disposal method in most developing countries. In China, approximately 85% of the generated MSW is being disposed of in the landfills. The amount of MSW is growing rapidly with the rate of approximately 8-10% annually, which contains a high quantity of moisture and organic matters. The problems of leachate treatment and landfill gas (LFG) emissions are increasing gradually. Reducing the hazard before emplacement, pretreatment of MSW before landfilling has become very important for the conventional landfill. In this study, aerobic pretreatment of mixed MSW was used, and much attention has been given to the natural convection of air in the mixed and unshredded MSW for bioconversion of organic matter (OM). This study is an attempt to investigate aerobic pretreatment suitability for the mixed and unshredded MSW at Beijing. A pilot-scale aerobic pretreatment simulator (APS) was developed at Beishen Shu Landfill in Beijing. To work out the biodegradation of the OM in the APS, fresh and pretreated MSW samples were collected and analyzed for OM, moisture content, temperature, chemical oxygen demand, total organic carbon, carbon, nitrogen, hydrogen, lignocelluloses, and biochemical methane potential at various stages of the pretreatment. Furthermore, results of the fresh and pretreated MSW are compared. Significant reduction in the observed parameters of the pretreated waste samples is observed. This work demonstrates that pretreatment is significantly effective in reducing the landfill emissions that is leachate and LFG.     

Greenhouse gas dynamics of municipal solid waste alternatives.

Previous greenhouse gas studies comparing landfilling with combustion of municipal solid waste (MSW) are limited to examinations of the emissions weighted by their relative radiative activity. This paper adds another dimension by analyzing the atmospheric response to these emissions. The heart of the analysis is a time-dependent model using a perturbation analysis of the IS92a results of the Intergovernmental Panel on Climate Change (IPCC). Using as inputs the emissions from the two technologies, the model calculates atmospheric concentration histories. Scenarios for a landfill and a combustor envision each accepting 1000 Mg refuse/day for a 30-year operating period followed by a 70-year postclosure period. The baseline scenario examines the basic greenhouse impact of each technology. The other scenario adds active gas collection at the landfill and energy offset credits for avoided power plant carbon emissions. For both scenarios, CH4 and trace gases from the landfill persist in the atmosphere, and they are relatively potent at forcing IR heating. The combination of these features place the landfill much higher than previously expected on the greenhouse impact scale. For the baseline scenario, the time-integrated radiative forcing from landfilling is 115 times that of combustion, and this ratio is 45 for the second scenario.     

城市生活垃圾卫生填埋场恶臭的防治技术进展

恶臭污染已成为垃圾处理和处置过程中的严重公害。在分析中,介绍了填埋场各区域恶臭的控制措施,综述了卫生填埋场恶臭的常规防治技术,重点讨论了生物技术在填埋场脱臭中的应用,这些防治技术对各类环境卫生设施,如垃圾收集站、中转站、焚烧场、堆肥厂及粪便处理厂的臭气治理均有借鉴意义。     

Model of municipal solid waste source separation activity: a case study of Beijing

One major challenge faced by Beijing is dealing with the enormous amount of municipal solid waste (MSW) generated, which contains a high percentage of food waste. Source separation is considered an effective means of reducing waste and enhancing recycling. However, few studies have focused on quantification of the mechanism of source separation activity. Therefore, this study was conducted to establish a mathematical model of source separation activity (MSSA) that correlates the source separation ratio with the following parameters: separation facilities, awareness, separation transportation, participation atmosphere, environmental profit, sense of honor, and economic profit. The MSSA consisted of two equations, one related to the behavior generation stage and one related to the behavior stability stage. The source separation ratios of the residential community, office building, and primary and middle school were calculated using the MSSA. Data for analysis were obtained from a 1-yr investigation and a questionnaire conducted at 128 MSW clusters around Beijing. The results revealed that office buildings had an initial separation ratio of 80% and a stable separation ratio of 65.86%, whereas residential communities and primary and middle schools did not have a stable separation ratio. The MSSA curve took on two shapes. In addition, internal motivations and the separation transportation ratio were found to be key parameters of the MSSA. This model can be utilized for other cities and countries.     

A life-cycle inventory model of municipal solid waste combustion

Evaluation of alternate strategies for municipal solid waste (MSW) management requires models to calculate environmental emissions as a function of both waste quantity and composition. A methodology to calculate waste component-specific emissions associated with MSW combustion is presented here. The methodology considers emissions at a combustion facility as well as those avoided at an electrical energy facility because of energy recovered from waste combustion. Emission factors, in units of kg pollutant per metric ton MSW entering the combustion facility, are calculated for CO2-biomass, CO2-fossil, SOx, HCl, NOx, dioxins/furans, PM, CO, and 11 metals. Water emissions associated with electrical energy offsets are also considered. Reductions in environmental emissions for a 500-metric-ton-per-day combustion facility that recovers energy are calculated.     

Spectroscopic characterization of water extractable organic matter during composting of municipal solid waste

This paper aims to characterize the evolution of water extractable organic matter (WEOM) during the composting of municipal solid waste (MSW), and investigate the correlation between maturity and WEOM characteristics. WEOM was extracted at different stages of MSW composting (0, 7, 14, 21, and 51 d) and characterized by FTIR, UV-Vis, and fluorescence spectroscopy. The results obtained show that the composting process decreased aliphatics, alcohols, polysaccharides, as well as protein-like materials, and increased aromatic polycondensation, humification, oxygen-containing functional groups, molecular weight, and humic-like materials. The maturity of MSW during composting was characterized by the presence of the peak with an excitation/emission wavelength pair of 289/421 nm in excitation-emission matrix spectra.     

Greenhouse Gas Dynamics of Municipal Solid Waste Alternatives

ABSTRACT

Previous greenhouse gas studies comparing landfilling with combustion of municipal solid waste (MSW) are limited to examinations of the emissions weighted by their relative radiative activity. This paper adds another dimension by analyzing the atmospheric response to these emissions. The heart of the analysis is a time-dependent model using a perturbation analysis of the IS92a results of the Intergovernmental Panel on Climate Change (IPCC). Using as inputs the emissions from the two technologies, the model calculates atmospheric concentration histories. Scenarios for a landfill and a combustor envision each accepting 1000 Mg refuse/day for a 30-year operating period followed by a 70-year postclosure period. The baseline scenario examines the basic greenhouse impact of each technology. The other scenario adds active gas collection at the landfill and energy offset credits for avoided power plant carbon emissions. For both scenarios, CH₄ and trace gases from the landfill persist in the atmosphere, and they are relatively potent at forcing IR heating. The combination of these features place the landfill much higher than previously expected on the greenhouse impact scale. For the baseline scenario, the time-integrated radiative forcing from landfilling is 115 times that of combustion, and this ratio is 45 for the second scenario.