Long-term coal gasification-based power with near-zero emissions. Part B: Zecomag and oxy-fuel IGCC cycles

In this second part of the work, two other long-term technologies for power generation from coal are investigated. The Zecomag plant has the same syngas production system of the Zecomix plant, described in the first part of this paper, but hydrogen-rich syngas is here burned with air in an open-cycle gas turbine. The aim is a simplification of the power island, more similar to a combined cycle; however, CO₂ capture falls from 100% to about 90% and NO_x emissions are present.An advanced oxy-fuel IGCC is the second plant investigated in this paper, presenting the same zero-emission potential of Zecomix. Syngas is produced in a high pressure, dry feed, oxygen blown gasifier and cleaned in a hot-gas-clean-up system. Clean syngas is then burned with oxygen and expanded in a turbine, using compressed recirculated CO₂ to moderate firing temperature and to cool turbine blades.The loss of net efficiency, with respect to Zecomix, is very limited (1–2 points) with both configurations. In order to better evaluate the performances obtained, a comparison with reference state-of-the art IGCCs and a long-term IGCC without CO₂ capture is also presented.     

Dispersion by wind of CO2 leaking from underground storage: Comparison of analytical solution with simulation

The concentration of CO₂ in air near the ground needs to be predicted to assess environmental and health risks from leaking underground storage. There is an exact solution to the advection–diffusion equation describing trace gases carried by wind when the wind profile is modeled with a power-law dependence on height. The analytical solution is compared with a numerical simulation of the coupled air–ground system with a source of CO₂ underground at the water table. The two methods produce similar results far from the boundaries, but the boundary conditions have a strong effect; the simulation imposes boundary conditions at the edge of a finite domain while the analytic solution imposes them at infinity. The reverse seepage from air to ground is shown in the simulation to be very small, and the large difference between time scales suggests that air and ground can be modeled separately, with gas emissions from the ground model used as inputs to the air model.     

Sizing and performance analysis of standalone hybrid photovoltaic/battery/hydrogen storage technology power generation systems based on the energy hub concept

In this study, the optimal sizing and performance analysis of a standalone integrated solar power system equipped with different storage scenarios to supply the power demand of a household is presented. One of the main purposes when applying solar energy resource is to face the increasing environmental pollutions resulting from fossil fuel based electricity sector. To this end, and to compare and examine two energy storage technologies (battery and hydrogen storage technology), three storage scenarios including battery only, hydrogen storage technology only and hybrid storage options are evaluated. An optimization framework based on Energy Hub concept is used to determine the optimum sizes of equipment for the lowest net present cost (NPC) while maintaining the system reliability. It was determined that the most cost effective and reliable case is the system with hybrid storage technology. Also, the effects of solar radiation intensity, the abatement potential of CO₂ emissions and converting excess power to hydrogen on the system’s performance and economics, were investigated and a few noticeable findings were obtained.     

Co-production of hydrogen and electricity with CO2 capture

Electricity and hydrogen can be used as energy carriers to reduce emissions of CO₂ from small and mobile energy users. One of the most promising technologies for the production of electricity and hydrogen with low CO₂ emissions is coal gasification with CO₂ capture and storage. Performance and cost data are presented for plants which produce electricity and hydrogen alone and plants which co-produce both of these energy carriers. The co-production plants include plants which produce a fixed ratio of hydrogen to electricity and plants which are able to vary the ratio while continuing to operate the gasification and CO₂ capture parts of the plant at full load. The paper also assesses the ability of these types of plants to satisfy the varying demands for hydrogen and electricity in future energy supply systems. The lowest cost option for the scenarios assessed in the paper is the use of flexible co-production plants with underground buffer storage of hydrogen.     

Devising an integrated methodology for analyzing energy use and CO2 emissions from Taiwan's petrochemical industries

Input-output modeling and multiplier analysis are used to assess Taiwan's five petrochemical industries, based upon their economic contribution and potential impacts on energy consumption and CO2 emission. In addition, a consolidated index system was developed for evaluating energy and economic efficiencies as well as targets for CO2 reduction. Results indicate that petrochemical materials (PM) make a major contribution to economic development, with lesser contributions from plastic materials (PL) and artificial fibres (AF). PM has the highest energy multiplier while PL has the largest induced potential for energy consumption. Plastic and rubber products (PP, RP) are relatively insignificant energy consumers. AF has the highest CO2 multiplier, and its induced potential for CO2 emission is the most significant. The consolidated index shows that the upstream petrochemical industries perform rather poorly in an integrated view of economic, energy, and CO2 emission, and should be seen as the primary targets for CO2 reduction. Investment of the petrochemical industries in Taiwan should be adjusted to improve energy efficiency, economic bases, and lower CO2 emissions.     

Corrective measures based on pressure control strategies for CO2 geological storage in deep aquifers

A prerequisite to the wide deployment at an industrial scale of CO₂ geological storage is demonstrating that potential risks can be efficiently managed. Corrective measures in case of significant irregularities, such as CO₂ leakage, are hence required as advocated by the recent European directive on Carbon Capture and Storage operations. In this regard, the objective of the present paper is to investigate four different corrective measures aiming at controlling the overpressure induced by the injection operations in the reservoir: stopping the CO₂ injection and relying on the natural pressure recovery in the reservoir; extracting the stored CO₂ at the injection well; extracting brine at a distant well while stopping the CO₂ injection, and extracting at a distant well without stopping the CO₂ injection. The efficiency of the measures is assessed using multi-phase fluid flow numerical simulations. The application case is the deep carbonate aquifer of the Dogger geological unit in the Paris Basin. A comparative study between the four corrective measures is then carried using a cost-benefit approach. Results show that an efficient overpressure reduction can be achieved by simply shutting-in the well. The overpressure reduction can be significantly accelerated by means of fluid extraction but the adverse consequences are the associated higher costs of the intervention operations.     

The acceptability of CO2 capture and storage (CCS) in Europe: An assessment of the key determining factors: Part 2. The social acceptability of CCS and the wider impacts and repercussions of its implementation

In Part 1, we presented the findings of the EU ACCSEPT project (2006–2007) with regards to scientific, technical, legal and economic issues. In Part 2, we present the analysis of social acceptability on the part of both the lay public and stakeholders. We examine the acceptability of CO₂ capture and geological storage (CCS) within the Clean Development Mechanism (CDM) of the Kyoto Protocol. The debate over the inclusion of CCS within the CDM is caught-up in a set of complex debates that are partly technical and partly political and, therefore, difficult, and time-consuming, to resolve. We explore concerns that support for CCS will detract from support for other low-carbon energy sources. We can find no evidence that support for CCS is currently detracting from support for renewable energy sources, though it is probably too early to detect such an effect. Efforts at understanding, engaging with, and communicating to, the lay public and wider stakeholder community (not just business) in Europe are currently weak and inadequate, despite well-meaning statements from governments and industry.     

Exergy analysis as a tool for the integration of very complex energy systems: The case of carbonation/calcination CO2 systems in existing coal power plants

A common characteristic of carbon capture and storage systems is the important energy consumption associated with the CO₂ capture process. This important drawback can be solved with the analysis, synthesis and optimization of this type of energy systems. The second law of thermodynamics has proved to be an essential tool in power and chemical plant optimization. The exergy analysis method has demonstrated good results in the synthesis of complex systems and efficiency improvements in energy applications.In this paper, a synthesis of pinch analysis and second law analysis is used to show the optimum window design of the integration of a calcium looping cycle into an existing coal power plant for CO₂ capture. Results demonstrate that exergy analysis is an essential aid to reduce energy penalties in CO₂ capture energy systems. In particular, for the case of carbonation/calcination CO₂ systems integrated in existing coal power plants, almost 40% of the additional exergy consumption is available in the form of heat. Accordingly, the efficiency of the capture cycle depends strongly on the possibility of using this heat to produce extra steam (live, reheat and medium pressure) to generate extra power at steam turbine. The synthesis of pinch and second law analysis could reduce the additional coal consumption due to CO₂ capture 2.5 times, from 217 to 85 MW.     

Large-scale impact of CO2 storage in deep saline aquifers: A sensitivity study on pressure response in stratified systems

Large volumes of CO₂ captured from carbon emitters (such as coal-fired power plants) may be stored in deep saline aquifers as a means of mitigating climate change. Storing these additional fluids may cause pressure changes and displacement of native brines, affecting subsurface volumes that can be significantly larger than the CO₂ plume itself. This study aimed at determining the three-dimensional region of influence during/after injection of CO₂ and evaluating the possible implications for shallow groundwater resources, with particular focus on the effects of interlayer communication through low-permeability seals. To address these issues quantitatively, we conducted numerical simulations that provide a basic understanding of the large-scale flow and pressure conditions in response to industrial-scale CO₂ injection into a laterally open saline aquifer. The model domain included an idealized multilayered groundwater system, with a sequence of aquifers and aquitards (sealing units) extending from the deep saline storage formation to the uppermost freshwater aquifer. Both the local CO₂-brine flow around the single injection site and the single-phase water flow (with salinity changes) in the region away from the CO₂ plume were simulated. Our simulation results indicate considerable pressure buildup in the storage formation more than 100 km away from the injection zone, whereas the lateral distance migration of brine is rather small. In the vertical direction, the pressure perturbation from CO₂ storage may reach shallow groundwater resources only if the deep storage formation communicates with the shallow aquifers through sealing units of relatively high permeabilities (higher than 10^?18 m²). Vertical brine migration through a sequence of layers into shallow groundwater bodies is extremely unlikely. Overall, large-scale pressure changes appear to be of more concern to groundwater resources than changes in water quality caused by the migration of displaced saline water.     

Basin-scale hydrogeologic impacts of CO2 storage: Capacity and regulatory implications

Industrial-scale injection of CO₂ into saline formations in sedimentary basins will cause large-scale fluid pressurization and migration of native brines, which may affect valuable groundwater resources overlying the deep sequestration aquifers. In this paper, we discuss how such basin-scale hydrogeologic impacts (1) may reduce current storage capacity estimates, and (2) can affect regulation of CO₂ storage projects. Our assessment arises from a hypothetical future carbon sequestration scenario in the Illinois Basin, which involves twenty individual CO₂ storage projects (sites) in a core injection area most suitable for long-term storage. Each project is assumed to inject five million tonnes of CO₂ per year for 50 years. A regional-scale three-dimensional simulation model was developed for the Illinois Basin that captures both the local-scale CO₂–brine flow processes and the large-scale groundwater flow patterns in response to CO₂ storage. The far-field pressure buildup predicted for this selected sequestration scenario support recent studies in that environmental concerns related to near- and far-field pressure buildup may be a limiting factor on CO₂ storage capacity. In other words, estimates of storage capacity, if solely based on the effective pore volume available for safe trapping of CO₂, may have to be revised based on assessments of pressure perturbations and their potential impacts on caprock integrity and groundwater resources. Our results suggest that (1) the area that needs to be characterized in a permitting process may comprise a very large region within the basin if reservoir pressurization is considered, and (2) permits cannot be granted on a single-site basis alone because the near- and far-field hydrogeologic response may be affected by interference between individual storage sites. We also discuss some of the challenges in making reliable predictions of large-scale hydrogeologic impacts related to CO₂ sequestration projects.     

CO2 capture from coal-fired power plants based on sodium carbonate slurry; a systems feasibility and sensitivity study

In this work the feasibility of a CO₂ capture system based on sodium carbonate–bicarbonate slurry and its integration with a power plant is studied. The results are compared to monoethanolamine (MEA)-based capture systems. Condensing power plant and combined heat and power plant with CO₂ capture is modelled to study the feasibility of combined heat and power plant for CO₂ capture.Environmental friendly sodium carbonate would be an interesting chemical for CO₂ capture. Sodium carbonate absorbs CO₂ forming sodium bicarbonate. The low solubility of sodium bicarbonate is a weak point for the sodium carbonate based liquid systems since it limits the total concentration of carbonate. In this study the formation of solid bicarbonate is allowed, thus forming slurry, which can increase the capacity of the solvent. With this the energy requirement of stripping of the solvent could potentially be around 3.22 MJ/kg of captured CO₂ which is significantly lower than with MEA based systems which typically have energy consumption around 3.8 MJ/kg of captured CO₂.Combined heat and power plants seem to be attractive for CO₂ capture because of the high total energy efficiency of the plants. In a condensing power plant the CO₂ capture decreases directly the electricity production whereas in a combined heat and power plant the loss can be divided between district heat and electricity according to demand.     

The acceptability of CO2 capture and storage (CCS) in Europe: An assessment of the key determining factors: Part 1. Scientific,technical and economic dimensions

The ACCSEPT project, which ran from January 2006 to December 2007, identified and analysed the main factors which have been influencing the emergence of CO₂ capture and geological storage (CCS) within the European Union (EU). The key clusters of factors concern science and technology, law and regulation, economics, and social acceptance. These factors have been analysed through interviews, a large-scale questionnaire conducted in 2006, and discussions in two stakeholder workshops (2006 and 2007). In Part I of this paper, we aim to distil the key messages and findings with regards to scientific, technical, legal and economic issues. There are no compelling scientific, technical, legal, or economic reasons why CCS could not be widely deployed in the forthcoming decades as part of a package of climate change mitigation options. In order to facilitate this deployment, governments at both the EU and Member State levels have an important role to play, in particular in establishing a robust and transparent legal framework (e.g. governing long-term environmental liability) and a strong policy framework providing sufficient and long-term incentives for CCS and CO₂ transportation networks.     

Feasibility of storing CO2 in the Utsira formation as part of a long term Dutch CCS strategy: An evaluation based on a GIS/MARKAL toolbox

This study provides insight into the feasibility of a CO₂ trunkline from the Netherlands to the Utsira formation in the Norwegian part of the North Sea, which is a large geological storage reservoir for CO₂. The feasibility is investigated in competition with CO₂ storage in onshore and near-offshore sinks in the Netherlands. Least-cost modelling with a MARKAL model in combination with ArcGIS was used to assess the cost-effectiveness of the trunkline as part of a Dutch greenhouse gas emission reduction strategy for the Dutch electricity sector and CO₂ intensive industry. The results show that under the condition that a CO₂ permit price increases from €25 per tCO₂ in 2010 to €60 per tCO₂ in 2030, and remains at this level up to 2050, CO₂ emissions in the Netherlands could reduce with 67% in 2050 compared to 1990, and investment in the Utsira trunkline may be cost-effective from 2020–2030 provided that Belgian and German CO₂ is transported and stored via the Netherlands as well. In this case, by 2050 more than 2.1 GtCO₂ would have been transported from the Netherlands to the Utsira formation. However, if the Utsira trunkline is not used for transportation of CO₂ from Belgium and Germany, it may become cost-effective 10 years later, and less than 1.3 GtCO₂ from the Netherlands would have been stored in the Utsira formation by 2050. On the short term, CO₂ storage in Dutch fields appears more cost-effective than in the Utsira formation, but as yet there are major uncertainties related to the timing and effective exploitation of the Dutch offshore storage opportunities.     

Informed and uninformed public opinions on CO2 capture and storage technologies in the Netherlands

Two research methods were used in this study to analyze the awareness and perception of the Dutch general public regarding Carbon dioxide Capture and Storage (CCS). In an Information-Choice Questionnaire (ICQ), a representative sample of the Dutch public (n = 995) was provided with all information on attributes of six CCS options, which experts deemed necessary to come to well-considered and well-informed opinions. A traditional questionnaire was used simultaneously (n = 327) to study uninformed evaluations of these technologies. The results showed that the Dutch public is mostly unaware of CCS and has little knowledge about how current energy use causes global warming. Uninformed respondents are still inclined to give their opinion however, which results in unpredictive, easily changeable opinions. ICQ respondents who processed information on attributes of CCS options were likely to base their option evaluations on this information, though not entirely. All in all, the results of the ICQ suggest that, after processing information deemed necessary by experts, Dutch people reluctantly agree with large scale implementation of each of the six CCS options.     

The potential for increased atmospheric CO2 emissions and accelerated consumption of deep geologic CO2 storage resources resulting from the large-scale deployment of a CCS-enabled unconventional fossil fuels industry in the U.S.

Desires to enhance the energy security of the United States have spurred renewed interest in the development of abundant domestic heavy hydrocarbon resources including oil shale and coal to produce unconventional liquid fuels to supplement conventional oil supplies. However, the production processes for these unconventional fossil fuels create large quantities of carbon dioxide (CO₂) and this remains one of the key arguments against such development. Carbon dioxide capture and storage (CCS) technologies could reduce these emissions and preliminary analysis of regional CO₂ storage capacity in locations where such facilities might be sited within the U.S. indicates that there appears to be sufficient storage capacity, primarily in deep saline formations, to accommodate the CO₂ from these industries. Nevertheless, even assuming wide-scale availability of cost-effective CO₂ capture and geologic storage resources, the emergence of a domestic U.S. oil shale or coal-to-liquids (CTL) industry would be responsible for significant increases in CO₂ emissions to the atmosphere. The authors present modeling results of two future hypothetical climate policy scenarios that indicate that the oil shale production facilities required to produce 3 MMB/d from the Eocene Green River Formation of the western U.S. using an in situ retorting process would result in net emissions to the atmosphere of between 3000 and 7000 MtCO₂, in addition to storing potentially 900–5000 MtCO₂ in regional deep geologic formations via CCS in the period up to 2050. A similarly sized, but geographically more dispersed domestic CTL industry could result in 4000–5000 MtCO₂ emitted to the atmosphere in addition to potentially 21,000–22,000 MtCO₂ stored in regional deep geologic formations over the same period. While this analysis shows that there is likely adequate CO₂ storage capacity in the regions where these technologies are likely to deploy, the reliance by these industries on large-scale CCS could result in an accelerated rate of utilization of the nation's CO₂ storage resource, leaving less high-quality storage capacity for other carbon-producing industries including electric power generation.     

Large-scale utilization of biomass energy and carbon dioxide capture and storage in the transport and electricity sectors under stringent CO2 concentration limit scenarios

Large-scale, dedicated commercial biomass energy systems are a potentially large contributor to meeting global climate policy targets by the end of the century. We use an integrated assessment model of energy and agriculture systems to show that, given a climate policy in which terrestrial carbon is appropriately valued equally with carbon emitted from the energy system, biomass energy has the potential to be a major component of achieving these low concentration targets. A key aspect of the research presented here is that the costs of processing and transporting biomass energy at much larger scales than current experience are explicitly incorporated into the modeling. From the scenario results, 120–160 EJ/year of biomass energy is produced globally by midcentury and 200–250 EJ/year by the end of this century. In the first half of the century, much of this biomass is from agricultural and forest residues, but after 2050 dedicated cellulosic biomass crops become the majority source, along with growing utilization of waste-to-energy. The ability to draw on a diverse set of biomass-based feedstocks helps to reduce the pressure for drastic large-scale changes in land use and the attendant environmental, ecological, and economic consequences those changes would unleash. In terms of the conversion of bioenergy feedstocks into value added energy, this paper demonstrates that biomass is and will continue to be used to generate electricity as well as liquid transportation fuels. A particular focus of this paper is to show how climate policies and technology assumptions – especially the availability of carbon dioxide capture and storage (CCS) technologies – affect the decisions made about where the biomass is used in the energy system. The potential for net-negative electric sector emissions through the use of CCS with biomass feedstocks provides an attractive part of the solution for meeting stringent emissions constraints; we find that at carbon prices above $150/tCO₂, over 90% of biomass in the energy system is used in combination with CCS. Despite the higher technology costs of CCS, it is a very important tool in controlling the cost of meeting a target, offsetting the venting of CO₂ from sectors of the energy system that may be more expensive to mitigate, such as oil use in transportation. CCS is also used heavily with other fuels such as coal and natural gas, and by 2095 a total of 1530 GtCO₂ has been stored in deep geologic reservoirs. The paper also discusses the role of cellulosic ethanol and Fischer–Tropsch biomass derived transportation fuels as two representative conversion processes and shows that both technologies may be important contributors to liquid fuels production, with unique costs and emissions characteristics.     

Effect of cattle slurry separation on greenhouse gas and ammonia emissions during storage

Storage of cattle slurry leads to emissions of methane (CH(4)), nitrous oxide (N(2)O), ammonia (NH(3)), and carbon dioxide (CO(2)). On dairy farms, winter is the most critical period in terms of slurry storage due to cattle housing and slurry field application prohibition. Slurry treatment by separation results in reduced slurry dry matter content and has considerable potential to reduce gaseous emissions. Therefore, the efficiency of slurry separation in reducing gaseous emissions during winter storage was investigated in a laboratory study. Four slurry fractions were obtained: a solid and a liquid fraction by screw press separation (SPS) and a supernatant and a sediment fraction by chemically enhanced settling of the liquid fraction. Untreated slurry and the separated fractions were stored in plastic barrels for 48 d under winter conditions, and gaseous emissions were measured. Screw press separation resulted in an increase of CO(2) (650%) and N(2)O (1240%) emissions due to high releases observed from the solid fraction, but this increase was tempered by using the combined separation process (CSP). The CSP resulted in a reduction of CH(4) emissions ( approximately 50%), even though high emissions of CH(4) (46% of soluble C) were observed from the solid fraction during the first 6 d of storage. Screw press separation increased NH(3) emissions by 35%, but this was reduced to 15% using the CSP. During winter storage greenhouse gas emissions from all treatments were mainly in the form of CH(4) and were reduced by 30 and 40% using SPS and CSP, respectively.     

Evaluating the impact of fractures on the performance of the In Salah CO2 storage site

The In Salah Gas Joint Venture CO₂ storage project has been in operation in Algeria since 2004 and is currently the world's largest onshore CO₂ storage project. CO₂ is injected into the saline aquifer of a gas reservoir several kilometres away from the gas producers. Current focus in the project is on implementing a comprehensive monitoring strategy and modelling the injection behaviour in order to ensure and verify safe long-term storage. A key part of this effort is the understanding of the processes involved in CO₂ migration within relatively low-permeability sandstones and shales influenced by fractures and faults. We summarise our current understanding of the fault and fracture pattern at this site and show preliminary forecasts of the system performance using discrete fracture models and fluid flow simulations. Despite evidence of fractures at the reservoir/aquifer level, the thick mudstone caprock sequence is expected to provide an effective flow and mechanical seal for the storage system; however, quantification of the effects of fracture flow is essential to the site verification.