Levels and composition of volatile organic compounds on commuting routes in Detroit, Michigan

Vehicle emissions can constitute a major share of ambient concentrations of many volatile organic compounds (VOCs) and other air pollutants in urban areas. Especially high concentrations may occur at curbsides, vehicle cabins, and other microenvironments. Such levels are not reflected by monitoring at fixed sites. This study reports on measurements of VOCs made from buses and cars in Detroit, MI. A total of 74 adsorbent tube samples were collected on 40 trips and analyzed by GC-MS for 77 target compounds. Three bus routes, selected to include residential, commercial and heavily industrialized areas, were sampled simultaneously on four sequential weeks during morning and afternoon rush hour periods. Nineteen compounds were regularly detected and quantified, the most prevalent of which included hexane/2-methyl pentane (15.6±5.8 μg m⁻³), toluene (10.2±7.9 μg m⁻³), m,p-xylene (6.8±4.7 μg m⁻³), benzene (4.5±3.0 μg m⁻³), 1,2,4-trimethylbenzene (4.0±2.6 μg m⁻³), o-xylene (2.2±1.6 μg m⁻³), and ethylbenzene (2.1±1.5 μg m⁻³). VOC levels in bus interiors and outdoor levels along the roadway were similar. Despite the presence of large industrial sources, route-to-route variation was small, but temporal variation was large and statistically significant. VOC compositions and trends indicate the dominance of vehicle sources over the many industrial sources in Detroit with the possible exceptions of styrene and several chlorinated VOCs. In-bus levels exceeded concentrations at fixed site monitors by a factor of 2–4. VOC concentrations in Detroit traffic are generally comparable to levels measured elsewhere in the US and Canada, but considerably lower than measured in Asia and Europe.     

Concentrations and elemental composition of particulate matter in the Buenos Aires underground system

Total suspended particulate (TSP) samples have been collected at six stations in the C and B lines of the Buenos Aires underground system and, almost simultaneously, at six ground level sites outside and nearby the corresponding underground stations, in the Oct 2005/Oct 2006 period. All these samples were analyzed for mass and elemental Fe, Cu, and Zn concentrations by using the Particle Induced X-ray Emission (PIXE) technique. Mostly, TSP concentrations were found to be between 152 μg m⁻³ (25% percentile) and 270 μg m⁻³ (75% percentile) in the platform of the stations, while those in outside ambient air oscillated from 55 μg m⁻³ (25% percentile) to 137 μg m⁻³ (75% percentile). Moreover, experimental results indicate that TSP levels are comparable to those measured for other underground systems worldwide. Statistical results demonstrate that subway TSP levels are about 3 times larger on average than those for urban ambient air. The TSP levels inside stations and outdoors are poorly correlated, indicating that TSP levels in the metro system are mainly influenced by internal sources.Regarding metal concentrations, the most enriched element in TSP samples was Fe, the levels of which ranged from 36 (25% percentile) to 86 μg m⁻³ (75% percentile) in Line C stations, while in Line B ones they varied between 8 μg m⁻³ (25% percentile) and 46 μg m⁻³ (75% percentile). As a comparison, Fe concentrations in ambient air oscillated between 0.7 μg m⁻³ (25% percentile) and 1.2 μg m⁻³ (75% percentile). Other enriched elements include Cu and Zn. With regard to their sources, Fe and Cu have been related to processes taking place inside the subway system, while Zn has been associated with outdoor vehicular traffic. Additionally, concerns about possible health implications based on comparisons to various indoor air quality limits and available toxicological information are discussed.     

Exposure of acid aerosol for schoolchildren in metropolitan Taipei

Metropolitan Taipei, which is located in the subtropical area, is characterized by high population and automobile densities. For convenience, most primary schools are located near major roads. This study explores the exposure of acid aerosols for schoolchildren in areas in Taipei with different traffic densities. Acid aerosols were collected by using a honeycomb denuder filter pack sampling system (HDS). Experimental results indicated that the air pollutants were significantly correlated with traffic densities. The ambient air NO₂, SO₂, HNO₃, NO₃⁻, SO₄²⁻, and aerosol acidity concentrations were 31.3 ppb, 4.7 ppb, 1.3 ppb, 1.9 μg m⁻³, 18.5 μg m⁻³, and 49.5 nmol m⁻³ in high traffic density areas, and 6.1 ppb, 1.8 ppb, 0.9 ppb, 0.7 μg m⁻³, 8.8 μg m⁻³ and 14.7 nmol m⁻³ in low traffic density areas. The exposure levels of acid aerosols for schoolchildren would be higher than the measurements because the sampling height was 5 m above the ground. The SO₂ levels were low (0.13–8.03 ppb) in the metropolitan Taipei. However, the SO₄²⁻ concentrations were relatively high, and might be attributed to natural emissions of sulfur-rich geothermal sources. The seasonal variations of acid aerosol concentrations were also observed. The high levels of acidic particles in spring time may be attributed to the Asian dust storm and low height of the mixture layer. We conclude that automobile contributed not only the primary pollutants but also the secondary acid aerosols through the photochemical reaction. Schoolchildren were exposed to twice the acid aerosol concentrations in high traffic density areas compared to those in low traffic density areas. The incidence of allergic rhinitis of schoolchildren in the high traffic density areas was the highest in spring time. Accompanied by high temperature variation and high levels of air pollution in spring, the health risk of schoolchildren had been observed.     

Monoterpene emissions and carbonyl compound air concentrations during the blooming period of rape (Brassica napus)

An increasing percentage of agricultural land in Germany is used for oil seed plants. Hence, rape has become an important agricultural plant (in Saxony 1998: 12% of the farmland) in the recent years. During flowering of rape along with intensive radiation and high temperatures, a higher production and emission of biogenic VOC was observed. The emissions of terpenes were determined and more importantly, high concentrations of organic carbonyl compounds were observed during this field experiment. All measurements of interest have been carried out during two selected days with optimal weather conditions. It is found that the origin or the mechanism of formation of different group of compounds had strong influence on the day to day variation of their concentrations. The emission flux of terpenes from flowering rape plants was determined to be 16–32 μg h⁻¹ m⁻² (30–60 ng h⁻¹ per g dry plant––540–1080 ng h⁻¹ per plant), in total. Limonene, α-thujene and sabinene were the most important compounds (about 60% of total terpenes). For limonene and sabinene reference emission rates (M_S) and temperature coefficients were determined: β_limonene=0.108 K⁻¹ and M_S=14.57 μg h⁻¹ m⁻²; β_sabinene=0.095 K⁻¹ and M_S=5.39 μg h⁻¹ m⁻².The detected carbonyl compound concentrations were unexpectedly high (maximum formaldehyde concentration was 18.1 ppbv and 3.4 ppbv for butyraldehyde) for an open field. Possible reasons for these concentrations are the combination of primary emission from the plants induced by high temperature and high ozone stress, the secondary formation from biogenically and advected anthropogenically emitted VOC at high radiation intensities and furthered by the low wind speeds at this time.     

Long-term variation of PM2.5 levels and composition at rural, urban, and roadside sites in Hong Kong: Increasing impact of regional air pollution

Long-term study of air pollution plays a decisive role in formulating and refining pollution control strategies. In this study, two 12-month measurements of PM_2.5 mass and speciation were conducted in 00/01 and 04/05 to determine long-term trend and spatial variations of PM_2.5 mass and chemical composition in Hong Kong. This study covered three sites with different land-use characteristics, namely roadside, urban, and rural environments. The highest annual average PM_2.5 concentration was observed at the roadside site (58.0±2.0 μg m⁻³ (average±2σ) in 00/01 and 53.0±2.7 μg m⁻³ in 04/05), followed by the urban site (33.9±2.5 μg m⁻³ in 00/01 and 39.0±2.0 μg m⁻³ in 04/05), and the rural site (23.7±1.9 μg m⁻³ in 00/01 and 28.4±2.4 μg m⁻³ in 04/05). The lowest PM_2.5 level measured at the rural site was still higher than the United States’ annual average National Ambient Air Quality Standard of 15 μg m⁻³. As expected, seasonal variations of PM_2.5 mass concentration at the three sites were similar: higher in autumn/winter and lower in summer. Comparing PM_2.5 data in 04/05 with those collected in 00/01, a reduction in PM_2.5 mass concentration at the roadside (8.7%) but an increase at the urban (15%) and rural (20%) sites were observed. The reduction of PM_2.5 at the roadside was attributed to the decrease of carbonaceous aerosols (organic carbon and elemental carbon) (>30%), indicating the effective control of motor vehicle emissions over the period. On the other hand, the sulfate concentration at the three sites was consistent regardless of different land-use characteristics in both studies. The lack of spatial variation of sulfate concentrations in PM_2.5 implied its origin of regional contribution. Moreover, over 36% growth in sulfate concentration was found from 00/01 to 04/05, suggesting a significant increase in regional sulfate pollution over the years. More quantitative techniques such as receptor models and chemical transport models are required to assess the temporal variations of source contributions to ambient PM_2.5 mass and chemical speciation in Hong Kong.     

Effect of outside air ventilation rate on volatile organic compound concentrations in a call center

A study of the relationship between outside air ventilation rate and concentrations of volatile organic compounds (VOCs) generated indoors was conducted in a call center office building. The building, with two floors and a total floor area of 4600 m², is located in the San Francisco Bay Area, CA. Ventilation rates were manipulated with the building's four air handling units (AHUs). VOC and CO₂ concentrations in the AHU returns were measured on 7 days during a 13-week period. VOC emission factors were determined for individual zones on days when they were operating at near steady-state conditions. The emission factor data were subjected to principal component (PC) analysis to identify groups of co-varying compounds. Potential sources of the PC vectors were ascribed based on information from the literature. The per occupant CO₂ generation rates were 0.0068–0.0092 l s⁻¹. The per occupant isoprene generation rates of 0.2–0.3 mg h⁻¹ were consistent with the value predicted by mass balance from breath concentration and exhalation rate. The relationships between indoor minus outdoor VOC concentrations and ventilation rate were qualitatively examined for eight VOCs. Of these, acetaldehyde and hexanal, which likely were associated with material sources, and decamethylcyclopentasiloxane, associated with personal care products, exhibited general trends of higher concentrations at lower ventilation rates. For other compounds, a clear inverse relationship between VOC concentrations and ventilation was not observed. The net concentration of 2,2,4-trimethyl-1,3-pentanediol monoisobutyrate isomers, examples of low-volatility compounds, changed very little with ventilation likely due to sorption and re-emission effects. These results illustrate that the efficacy of ventilation for controlling VOC concentrations can vary considerably depending upon the operation of the building, the pollutant sources and the physical and chemical processes affecting the pollutants. Thus, source control measures, in addition to adequate ventilation, are required to limit concentrations of VOCs in office buildings.     

Trans-boundary air pollution over remote islands in Japan: observed data and estimates from a numerical model

Observations of air pollutants were conducted in remote Japanese islands (Oki Island and Okinawa Island) in early spring to clarify the extent of trans-boundary air pollution from the Asian continent. A three-dimensional Eulerian model calculation, which included parameters on emission, transport and transformation of sulfur oxides, nitrogen oxides and ammonia, was performed to compile sulfate isosurface concentrations over the observational sites. Concentrations of non-sea-salt sulfate (nss-SO₄²⁻) of greater than 10 μg m⁻³ were observed at Oki after the northeastward passage of low-pressure systems in the Sea of Japan. At these times, the weather showed a typical winter pattern and air pollutants over China were transported southeastward to Japan with the northwesterly wind. The model calculation reproduced the observed variations of nss-SO₄²⁻ concentration well, except for one case in which the model calculation could not reproduce the extremely low nss-SO₄²⁻ concentration observed on 8 March. In Hedo (Okinawa Island), we observed long-lasting (3 days) medium concentrations of nss-SO₄²⁻ (approximately 5 μg m⁻³). Although the model reproduced these observed medium concentrations well, in general the observed results were reproduced better for Oki than for Hedo. Under the synoptic weather conditions of early spring, high concentrations of nss-sulfate were sometimes transported to these remote Japanese islands from areas of continental Asia with a strong outflow of air pollutants.     

Volatile organic compound concentrations, emission rates, and source apportionment in newly-built apartments at pre-occupancy stage

The present study investigated the indoor concentrations of selected volatile organic compounds (VOCs) and formaldehyde and their indoor emission characteristics in newly-built apartments at the pre-occupancy stage. In total, 107 apartments were surveyed for indoor and outdoor VOC concentrations in two metropolitan cities and one rural area in Korea. A mass balanced model was used to estimate surface area-specific emission rates of individual VOCs and formaldehyde. Seven (benzene, ethyl benzene, toluene, m,p-xylene, o-xylene, n-hexane, and n-heptane) of 40 target compounds were detectable in all indoor air samples, whereas the first five were detected in all outdoor air samples. Formaldehyde was also predominant in the indoor air samples, with a high detection frequency of 96%. The indoor concentrations were significantly higher than the outdoor concentrations for aromatics, alcohols, terpenes, and ketones. However, six halogenated VOCs exhibited similar concentrations for indoor and outdoor air samples, suggesting that they are not major components emitted from building materials. It was also suggested that a certain portion of the apartments surveyed were constructed by not following the Korean Ministry of Environment guidelines for formaldehyde emissions. Toluene exhibited the highest emission rate with a median value of 138 μg m⁻² h⁻¹. The target compounds with median emission rates greater than 20 μg m⁻² h⁻¹ were toluene, 1-propanol, formaldehyde, and 2-butanone. The wood panels/vinyl floor coverings were the largest indoor pollutant source, followed by floorings, wall coverings, adhesives, and paints. The wood panels/vinyl floor coverings contributed nearly three times more to indoor VOC concentrations than paints.     

A study on emission of phthalate esters from plastic materials using a passive flux sampler

Phthalate esters are used as plasticizer in many plastics, and several studies have shown their toxicity. Phthalate esters are gradually emitted over time, and so it is conceivable that they pose a significant health risk. This study aims to investigate the temperature dependence of the emissions of various phthalate esters and to estimate the health risks of these emissions at various temperatures. A passive-type sampler was developed to measure the flux of phthalate esters from the surface of plastic materials. With this sampler, we examined three widely used plastic materials: synthetic leather, wallpaper and vinyl flooring. The observed maximum emissions of diethyl phthalate, dibutyl phthalate, and diethylhexyl phthalate (DEHP) from these materials at 20°C were 0.89, 0.77, and 14 μg m⁻² h⁻¹, respectively. Emissions at 80°C were 2.8, 4.5×10², and 1.5×10³ μg m⁻² h⁻¹, respectively. The results showed this temperature dependence is determined primarily by the type of phthalate ester and less so by the type of material. The estimation from the results of temperature dependence indicated the concentration of DEHP in a vehicle left out in the sunshine during the day can exceed the recommended levels of Japan Ministry of Health, Labour and Welfare.     

Transient analysis of volatile organic compound concentrations for estimating emission rates

While emission rates of volatile organic compounds (VOCs) have been obtained for building materials, furnishings and processes in chambers, field measurements are more difficult. Procedures to estimate emission rates using transient analysis of VOC concentrations are described and applied in a two-story classroom/office building. The analysis employs semi-real-time VOC concentrations determined with a portable GC/FID and simultaneous air change rate measurements using tracer gas decay. The results of the analysis yield consistent values of emission rates for building materials ranging from 0.20 to 0.40 mg m⁻² h⁻¹ when normalized by floor area. Occupancy-related emissions were more difficult to estimate and covered a wider range from roughly 0.1 to 1.5 mg m⁻² h⁻¹. The test data were also analyzed in an attempt to determine sink parameters, but these efforts were not particularly successful. Furthermore, in these tests, the inclusion of sink effects did not significantly impact the estimated emission rates. While this paper offers a transient analysis approach that may lead to improved field estimates of VOC emission rates, it is not presented as a definitive methodology. Nevertheless, transient analysis has potential for use in other buildings, but simultaneous air change rate measurements are critical in its application in estimating VOC emission rates in the field.     

Fine particulate (PM2.5) composition in Atlanta, USA: assessment of the particle concentrator-Brigham Young University organic sampling system, PC-BOSS, during the EPA supersite study

Aerosol concentrations of carbonaceous material, sulfate, and nitrate for samples obtained using a newly designed PC-BOSS are reported. The results indicated that PM_2.5 composition in Atlanta was dominated by sulfate and organic material, with low concentrations of particulate nitrate. Observed average particulate component concentrations for the 26-day study period were: sulfate, 12.2 μg/m³ (17.0 μg/m³ as ammonium sulfate); non-volatile organic material, 11.4 μg OM/m³ (assumes organic material, OM, is 61% C); semi-volatile organic compounds (SVOC) lost from particles during sampling, 5.3 μg OM/m³; filter retained nitrate, 0.1 μg/m³ (0.2 μg/m³ as ammonium nitrate); nitrate lost from particles, 0.3 μg/m³ (0.4 μg/m³ as ammonium nitrate); and soot (elemental carbon), 1.5 μg/m³. The PC-BOSS particle concentrator efficiency was obtained by comparison of the PC-BOSS sulfate data with sulfate data obtained from the Federal Reference Method (FRM) sampler. A modification of the PC-BOSS design to allow independent determination of this parameter is recommended.     

Sources of Volatile Organic Compounds in a University Building

A total of 34 volatile organic compounds (VOCs) were measured in the indoor of laboratories, offices and classrooms of the Chemical Engineering Department of Hacettepe University in Ankara in 2 week-day passive sampling campaigns. The average concentrations ranged from 0.77 to 265 μg m^?3 at the different indoor sites, with the most abundant VOC found to be toluene (119.6 μg m^?3), followed by styrene (21.24 μg m^?3), 2-ethyltoluene (17.11 μg m^?3), n-hexane (10.21 μg m^?3) and benzene (9.42 μg m^?3). According to the factor analysis, the evaporation of solvents used in the laboratories was found to be the dominant source.     

Assessment of traffic-related air pollution in the urban streets before and during the 2008 Beijing Olympic Games traffic control period

In order to investigate the air quality and the abatement of traffic-related pollution during the 2008 Olympic Games, we select 12 avenues in the urban area of Beijing to calculate the concentrations of PM₁₀, CO, NO₂ and O₃ before and during the Olympic traffic controlling days, with the OSPM model.Through comparing the modeled results with the measurement results on a representative street, the OSPM model is validated as sufficient to predict the average concentrations of these pollutants at street level, and also reflects their daily variations well, i.e. CO presents the similar double peaks as the traffic flow, PM₁₀ concentration is influenced by other sources. Meanwhile, the model predicts O₃ to stay less during the daytime and ascend in the night, just opposite to NO₂, which reveals the impact of photochemical reactions. In addition, the predicted concentrations on the windward side often exceed the leeward side, indicating the impact of the special street shape, as well as the wind.The comparison between the predicted street concentrations before and during the Olympic traffic control period shows that the overall on-road air quality was improved effectively, due to the 32.3% traffic flow reduction. The concentrations of PM₁₀, CO and NO₂ have reduced from 142.6 μg m⁻³, 3.02 mg m⁻³ and 118.7 μg m⁻³ to 102.0 μg m⁻³, 2.43 mg m⁻³ and 104.1 μg m⁻³. However, the different pollutants show diverse changes after the traffic control. PM₁₀ decreases most, and the reduction effect focusing on the first half-day even clears the morning peak, whereas CO and NO₂ have even reductions to minify the daily fluctuations on the whole. Opposite to the other pollutants, ozone shows an increase of concentration. The average reduction rate of PM₁₀, CO, NO₂ and O₃ are respectively 28%, 19.3%, 12.3% and −25.2%. Furthermore, the streets in east, west, south and north areas present different air quality improvements, probably induced by the varied background pollution in different regions around Beijing, along with the impact of wind force. This finding suggests the pollution control in the surrounding regions, not only in the urban area.     

VOCs in representative canadian residences

Stored extracts of passive samplers exposed in 757 randomly selected Canadian residences provided a unique opportunity for retrospective determination of the occurrence of airborne volatile organic compounds (VOCs). Aliquots of the individual extracts were pooled to form a composite exposure sample and a corresponding blank sample. To identify and quantitate potentially hazardous organics in the samples, GC-MS analyses were conducted by several approaches. The amounts of 52 target compounds in the the composite sample were estimated based on selected ion monitoring (SIM) results, extraction recoveries, average air volume sampled, and 3M OVM 3500 passive sampling rates. Forty of the organics were detected and were present in amounts equivalent to airborne concentrations ranging from <1 to 104 μg m⁻³. Several other compounds were also tentatively identified by full scan analysis. Many of the detected organics have been reported to be associated with activities such as tobacco smoking and the presence of consumer products and plastic materials indoors. The analytical results have been useful in risk assessments and establishment of a new Canadian priority substances list (PSL).     

Emissions of organophosphate and brominated flame retardants from selected consumer products and building materials

The emissions of selected flame retardants were measured in 1- and 0.02-m³ emission test chambers and 0.001-m³ emission test cells. Four product groups were of interest: insulating materials, assembly foam, upholstery/mattresses, and electronics equipment. The experiments were performed under constant environmental conditions (23°C, 50% RH) using a fixed sample surface area and controlled air flow rates. Tris (2-chloro-isopropyl)phosphate (TCPP) was observed to be one of the most commonly emitted organophosphate flame retardants in polyurethane foam applications. Depending on the sample type, area-specific emission rates (SER_a) of TCPP varied between 20 ng m⁻² h⁻¹ and 140 μg m⁻² h⁻¹.The emissions from electronic devices were measured at 60°C to simulate operating conditions. Under these conditions, unit specific emission rates (SER_u) of organophosphates were determined to be 10–85 ng unit⁻¹ h⁻¹. Increasing the temperature increased the emission of several flame retardants by up to a factor of 500. The results presented in this paper indicate that emissions of several brominated and organophosphate flame retardants are measurable. Polybrominated diphenylethers exhibited an SER_a of between 0.2 and 6.6 ng m⁻² h⁻¹ and an SER_u of between 0.6 and 14.2 ng unit⁻¹ h⁻¹. Because of sink effects, i.e., sorption to chamber components, the emission test chambers and cells used in this study have limited utility for substances low vapour pressures, especially the highly brominated compounds; hexabromocyclododecane had an SER_a of between 0.1 and 29 ng m⁻² h⁻¹ and decabromodiphenylether was not detectable at all.     

Investigation of the Treatability of the Primary Indoor Volatile Organic Compounds on Activated Carbon Fiber Cloths at Typical Indoor Concentrations

Abstract

Volatile organic compounds (VOCs) are a major concern for indoor air pollution because of the impacts on human health. In recent years, interest has increased in the development and design of activated carbon filters for removing VOCs from indoor air. Although extensive information is available on sources, concentrations, and types of indoor VOCs, there is little or no information on the performance of indoor air adsorption systems for removing low concentrations of primary VOCs. Filter designs need to consider various factors such as empty bed contact time, humidity effects, competitive adsorption, and feed concentration variations, whereas adsorption capacities of the indoor VOCs at the indoor concentration levels are important parameters for filter design. A preliminary assessment of the feasibility of using adsorption filters to remove low concentrations of primary VOCs can be performed. This work relates the information (including VOC classes in indoor air, the typical indoor concentrations, and the adsorption isotherms) with the design of a particular adsorbent/adsorbates system. As groundwork for filter design and development, this study selects the primary VOCs in indoor air of residences, schools, and offices in different geographical areas (North America, Europe, and Asia) on the basis of occurrence, concentrations, and health effects. Activated carbon fiber cloths (ACFCs) are chosen as the adsorbents of interest. It is demonstrated that the isotherm of a VOC (e.g., toluene on the ACFC) at typical indoor concentrations—parts per billion by volume (ppbv) level—is different than the isotherm at parts per million by volume (ppmv) levels reported in the publications. The isotherms at the typical indoor concentrations for the selected primary VOCs are estimated using the Dubinin–Radushkevitch equation. The maximum specific throughput for an indoor VOC removal system to remove benzene is calculated as a worst-case scenario. It is shown that VOC adsorption capacity is an important indicator of a filter’s lifetime and needs to be studied at the appropriate concentration range. Future work requires better understanding of the realistic VOC concentrations and isotherms in indoor environments to efficiently utilize adsorbents.     

Volatile organic compounds in roadside microenvironments of metropolitan Hong Kong

The characteristics and concentrations of volatile organic compounds (VOCs) in the roadside microenvironments of metropolitan Hong Kong were investigated. The VOC concentrations, especially toluene, benzene and chlorinated VOCs in Hong Kong were high when compared with those in most developed cities. The average and maximum concentration of toluene was 74.9 and 320.0 μg m⁻³, respectively. The respective values for benzene were 25.9 and 128.6 μg m⁻³. The chlorinated VOCs were dominated by trichloroethylene and tetrachloroethylene. The maximum concentrations of these two species reached 248.2 and 144.0 μg m⁻³, respectively. There were strong variations in the spatial fluctuation and characteristic of VOC concentrations. The highest VOC concentrations were found in the industrial district, which were followed by those in the commercial district, the central business district and finally the residential district. The highest concentrations of most VOC species, especially chlorinated VOC were found in the industrial and commercial districts. The average benzene/toluene ratio in Hong Kong was 0.5 suggesting that vehicular emission was the dominant VOC source in most areas of Hong Kong. There were strong deviations in benzene/toluene, benzene/ethylbenzene and benzene/(m+p-xylene) ratios in the commercial district, and highly chlorinated VOC in the industrial and commercial districts. These suggest that there were other benzene and VOC sources overlying on the high background VOC concentrations in these districts. The common usage of organic solvents in the building and construction industries, and in the small industries in the industrial and commercial districts were believed to be important sources of VOC in Hong Kong.     

Mercury deposition/accumulation rates in the vicinity of a lead smelter as recorded by a peat deposit

Mercury (Hg) concentration profiles and historical accumulation rates were determined in three ²¹⁰Pb-dated cores from a peat deposit in the vicinity of a lead (Pb) smelter at Příbram, Czech Republic. The Hg concentrations in peat samples ranged from 66 to 701 μg kg⁻¹. Cumulative Hg inventories from each core (for the past 150 yr) varied by a factor of 1.4 (13.6–18.5 mg Hg m⁻²), indicating variations of net Hg accumulation rate within the peat deposit. Historical changes in vegetation cover (leading to variable interception by trees) are probably responsible for this variation in space and time. The uncorrected Hg accumulation rates peaked between the 1960s and 1980s (up to 226 μg m⁻² yr⁻¹). Recent findings show that Hg records from peat tend to overestimate historical levels of Hg deposition. Therefore we used the mass loss compensation factor (MLCF) to normalize Hg accumulation rates. These corrected Hg accumulation rates were significantly lower (maximum 129 μg m⁻² yr⁻¹) and better corresponded to changes in historical smelter emissions, which were highest in the 1960s. The agreement between the corrected Hg accumulation rates in the uppermost peat sections (2–38 μg m⁻² yr⁻¹) and biomonitoring of atmospheric deposition by mosses in several recent years (4.7–34.4 μg m⁻² yr⁻¹) shows the usefulness of MLCF application on Hg accumulation in peat archives. However, the MLCF correction was unsuitable for Pb. The recent Pb deposition rates obtained by an independent biomonitoring study using mosses (0.5–127 mg m⁻² yr⁻¹) were better correlated with net Pb accumulation rates recorded in peat (7–145 mg m⁻² yr⁻¹) than with corrected rates obtained by the MLCF approach (1–28 mg m⁻² yr⁻¹).     

A global assessment of chromium pollution using sperm whales (Physeter macrocephalus) as an indicator species

Chromium (Cr) is a well-known human carcinogen and a potential reproductive toxicant, but its contribution to ocean pollution is poorly understood. The aim of this study was to provide a global baseline for Cr as a marine pollutant using the sperm whale (Physeter macrocephalus) as an indicator species. Biopsies were collected from free-ranging whales around the globe during the voyage of the research vessel The Odyssey. Total Cr levels were measured in 361 sperm whales collected from 16 regions around the globe detectable levels ranged from 0.9 to 122.6 μg Cr g tissue⁻¹ with a global mean of 8.8 ± 0.9 μg g⁻¹. Two whales had undetectable levels. The highest levels were found in sperm whales sampled in the waters near the Islands of Kiribati in the Pacific (mean = 44.3 ± 14.4) and the Seychelles in the Indian Ocean (mean = 19.5 ± 5.4 μg g⁻¹). The lowest mean levels were found in whales near the Canary Islands (mean = 3.7 ± 0.8 μg g⁻¹) and off of the coast of Sri Lanka (mean = 3.3 ± 0.4 μg g⁻¹). The global mean Cr level in whale skin was 28-times higher than mean Cr skin levels in humans without occupational exposure. The whale levels were more similar to levels only observed previously in human lung tissue from workers who died of Cr-induced lung cancer. We conclude that Cr pollution in the marine environment is significant and that further study is urgently needed.     

A new direct thermal desorption-GC/MS method: Organic speciation of ambient particulate matter collected in Golden, BC

Particulate matter having an aerodynamic diameter less than 2.5 μm (PM2.5) is thought to be implicated in a number of medical conditions, including cancer, rheumatoid arthritis, heart attack, and aging. However, very little chemical speciation data is available for the organic fraction of ambient aerosols. A new direct thermal desorption-gas chromatography/mass spectrometry (TD-GC/MS) method was developed for the analysis of the organic fraction of PM2.5. Samples were collected in Golden, British Columbia, over a 15-month period. n-Alkanes constituted 33–98% by mass of the organic compounds identified. PAHs accounted for 1–65% and biomarkers (hopanes and steranes) 1–8% of the organic mass. Annual mean concentrations were: n-alkanes (0.07–1.55 ng m⁻³), 16 PAHs (0.02–1.83 ng m⁻³), and biomarkers (0.02–0.18 ng m⁻³). Daily levels of these organics were 4.89–74.38 ng m⁻³, 0.27–100.24 ng m⁻³, 0.14–4.39 ng m⁻³, respectively. Ratios of organic carbon to elemental carbon (OC/EC) and trends over time were similar to those observed for PM2.5. There was no clear seasonal variation in the distribution of petroleum biomarkers, but elevated levels of other organic species were observed during the winter. Strong correlations between PAHs and EC, and between petroleum biomarkers and EC, suggest a common emission source – most likely motor vehicles and space heating.