Adsorptive separation of cadmium from aqueous solutions and wastewaters by riverbed sand

Application of riverbed sand for the adsorptive separation of cadmium(II) from aqueous solutions has been investigated. Removal increased from 26.8 to 56.4% by decreasing the initial concentration of cadmium from 7.5 x 10(-5) to 1.0 x 10(-5)M at pH 6.5, 25 degrees C temperature, agitation speed of 100 rpm, 100 microm particle size and 1.0 x 10(-2) NaClO4 ionic strength. Process of separation is governed by first order rate kinetics. The value of rate constant of adsorption, k(ad), was found to be 2.30 x 10(-2)per min at 25 degrees C. Values of coefficient of mass transfer, beta L, were calculated and its value at 25 degrees C was found to be 1.92 x 10(-2)cm/s. Values of Langmuir constant were calculated. Values of thermodynamic parameters delta G0, delta H0 and delta S0 were also calculated and were recorded as -0.81 kcal/mol, -9.31 kcal/mol and -28.10 cal/mol at 25 degrees C. pH has been found to affect the removal of cadmium significantly and maximum removal, 58.4%, has been found at pH 8.5. Process can be used for treatment of cadmium(II) rich wastewaters.     

Efficient dehalogenation of automobile shredder residue in NaOH/ethylene glycol using a ball mill

We investigated the effectiveness of sodium hydroxide/ethylene glycol (NaOH/EG) for dehalogenation of automobile shredder residue (ASR) using a ball mill. Efficient dehalogenation was achieved at atmospheric pressure by combining the use of EG (196 degrees C b.p.) as a replacement solvent for NaOH with ball milling, which improved contact between ASR and OH(-) in solution. Moderate NaOH concentrations and increased ball mill rotation speeds produced high dechlorination that was not significantly affected by the weight ratio of ASR to EG. NaOH/EG dechlorination increased with temperature with an apparent activation energy of 50 kJ mol(-1) confirming that the reaction proceeded under chemical reaction control. The modified shrinking-core model was appropriate to explain the dechlorination process. Low chloro levels in our NaOH/EG-treated ASR suggested that this material could be used for feedstock recycling and the wet process may be applicable for dehalogenation of other important waste streams.     

Kinetics of the chemical degradation of diuron

The influence of pH and buffer concentration on the chemical degradation of diuron in water has been analysed over a wide temperature range. The process irreversibly gives 3,4-dichloroaniline as the only product containing the phenyl ring. H+, OH- and phosphate buffer are efficient catalysts of the reaction. The rate constant first increases rapidly at low buffer concentrations and then gradually levels off at higher ones. At 40 degrees C and high phosphate concentration (>0.01 M), or in the extreme pH regions, the half-life is approximately 4 months and the activation energy is 127 +/- 2 kJmol(-1).     

Kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE)

The kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE) in aqueous solutions at various pH, temperature, oxidant concentration and ionic strength levels was studied. The MTBE degradation was found to follow a pseudo-first-order decay model. The pseudo-first-order rate constants of MTBE degradation by persulfate (31.5 mM) at pH 7.0 and ionic strength 0.11 M are approximately 0.13 x 10(-4), 0.48 x 10(-4), 2.4 x 10(-4) and 5.8 x 10(-4) S(-1) at 20, 30, 40 and 50 degrees C, respectively. Under the above reaction conditions, the reaction has an activation energy of 24.5 +/- 1.6 kcal/ mol and is influenced by temperature, oxidant concentration, pH and ionic strength. Raising the reaction temperature and persulfate concentration may significantly accelerate the MTBE degradation. However, increasing both pH (over the range of 2.5-11) and ionic strength (over the range of 0.11-0.53 M) will decrease the reaction rate. Reaction intermediates including tert-butyl formate, tert-butyl alcohol, acetone and methyl acetate were observed. These intermediate compounds were also degraded by persulfate under the experimental conditions. Additionally, MTBE degradation by persulfate in a groundwater was much slower than in phosphate-buffer solutions, most likely due to the presence of bicarbonate ions (radical scavengers) in the groundwater.     

Kinetics and mechanism of oxidation of tetrachloroethylene with permanganate

The kinetics, reaction pathways and product distribution of oxidation of tetrachloroethylene (PCE) by potassium permanganate (KMnO4) were studied in phosphate-buffered solutions under constant pH, isothermal, completely mixed and zero headspace conditions. Experimental results indicate that the reaction is first-order with respect to both PCE and KMnO4 and has an activation energy of 9.3+/-0.9 kcal/mol. The second-order rate constant at 20 degrees C is 0.035+/-0.004 M(-1) s(-1), and is independent of pH and ionic strength (I) over a range of pH 3-10 and I approximately 0-0.2 M, respectively. The PCE-KMnO4 reaction may proceed through further oxidation and/or hydrolysis reaction pathways, greatly influenced by the acidity of the solution, to yield CO2(g), oxalic acid, formic acid and glycolic acid. Under acidic conditions (e.g., pH 3), the further oxidation pathway will dominate and PCE tends to be directly mineralized into CO2 and chloride. Under neutral (e.g., pH 7) and alkaline conditions (e.g., pH 10), the hydroxylation pathway dominates the reaction and PCE is primarily transformed into oxalic acid prior to complete PCE mineralization. Moreover, all chlorine atoms in PCE are rapidly liberated during the reaction and the rate of chloride production is very close to the rate of PCE degradation.     

Pyrolytic characteristics of sewage sludge

In this study, a number of different sewage sludge including sludge samples from industrial and hospital wastewater treatment plants were characterized for pyrolysis behavior by means of thermogravimetric analysis up to 800 degrees C. According to the thermogravimetric results, five different types of mass loss behaviors were observed depending on the nature of the sludge used. Typical main decomposition steps occurred between 250 and 550 degrees C although some still decomposed at higher temperatures. The first group (Types I, II and III) was identified by main decomposition at approximately 300 degrees C and possible second reaction at higher temperature. Differences in the behavior may be due to different components in the sludge both quantitatively and qualitatively. The second group (Types IV and V), which rarely found, has unusual properties. DTG peaks were found at 293, 388 and 481 degrees C for Type IV and 255 and 397 degrees C for Type V. Kinetics of sludge decomposition can be described by either pseudo single or multicomponent overall models (PSOM or PMOM). The activation energy of the first reaction, corresponding to the main pyrolysis typically at 300 degrees C, was rather constant (between 68 and 77 kJ mol(-1)) while those of second and third reactions were varied in the range of 85-185 kJ mol(-1). The typical order of pyrolysis reaction was in the range of 1.1-2.1. The pyrolysis gases were composed of both saturated and unsaturated light hydrocarbons, carbon dioxide, ethanol and chloromethane. Most products, however, evolve at a quite similar temperature regardless of the sludge type.     

Dehalogenation Potential of Municipal Waste Incineration Fly Ash

BACKGROUND, AIMS AND SCOPE: In the first part of this paper the main principles which control the dehalogenation of polychlorinated aromatic compounds on municipal waste incineration fly ash (MWI-FA) have been discussed and the model fly ash of similar dehalogenation activity has been proposed. Even if both systems show comparable dehalogenation properties, the main question concerning the postulated identical reaction mechanism in both cases is left unanswered. The other very important point is to what extent is this dechlorination mechanism thermodynamically controlled. The same problem is often discussed in the literature also for the de novo synthetic reactions. From the data it is clear that metallic copper plays a decisive role in the mechanism of the dehalogenation reaction. Although the results reported in the first part strongly support the idea that copper acts in this dechlorination as the reaction component, in contrast to its generally accepted catalytic behaviour, we believed that additional support for this conclusion can be obtained with the help of a thermodynamic interpretation of the mechanism of the reaction. RESULTS AND DISCUSSION: The pathways of hexachlorobenzene dechlorination on MWI-FA and model fly ash were studied in a closed system at 260-300 degrees C under nitrogen atmosphere. These pathways were the same for both systems, with the following prevailing sequences: hexachlorobenzene --> pentachlorobenzene --> 1,2,3,5-tetrachlorobenzene --> 1,3,5-trichlorobenzene --> 1,3-dichlorobenzene. Thermodynamic calculations were carried out by using the method of minimization total Gibbs energy of the whole system. In the calculations, the following reaction components were taken into account: all gaseous chlorinated benzenes, benzene, hydrogen chloride, a gaseous trimer Cu3Cl3, and also Cu2O and CuCl2 as solid components. The effect of the reaction temperature and the amount of copper and water vapour were considered as well. The effect of reaction temperature was determined from the data calculated for the 500 to 750 K temperature region. The effect of the initial composition was determined for the molar amounts of copper = 0.01-3 moles and water vapour = 0.2 to 3 moles per mole of chlorobenzene isomer CONCLUSIONS: The results of hexachlorobenzene dechlorination by MWI-FA and model fly ash under comparable reaction conditions allow us to conclude that both dechlorinations proceed via the same dechlorination pathways, which can be taken as an evidence of the identical dehalogenation mechanism for both systems. The relative percentual distribution of the dehalogenated products depends on the temperature, but not on the initial amount of water vapour or copper metal. On the other hand, the initial amount of copper substantially affects the conversion of the dehalogenation as well as the molar ratio of Cu3Cl3 to HCl in the equilibrium mixture. Comparison of the experimental with thermodynamic results supports the idea that dehalogenation reactions are thermodynamically controlled. RECOMMENDATIONS AND OUTLOOK: Thermodynamic analysis of the dehalogenation reactions may prove useful for a wide range of pollutants. The calculations concerning polychlorinated biphenyls and phenols are under study.     

Bioavailability and mass balance studies of a commercial pentabromodiphenyl ether mixture in male Sprague-Dawley rats

Cyanogenic glycosides are common plant toxins. Toxic hydrogen cyanide originating from cyanogenic glycosides may affect soil processes and water quality. In this study, hydrolysis, degradation and sorption of dhurrin (4-hydroxymandelonitrile-beta-d-glucoside) produced by sorghum has been studied in order to assess its fate in soil. The log K(ow) of dhurrin was -1.18+/-0.08 (22 degrees C). Hydrolysis was a first-order reaction with respect to dhurrin and hydroxyl ion concentrations. Half lives ranged from 1.2h (pH 8.6; 25 degrees C) to 530d (pH 4; 25 degrees C). The activation energy of hydrolysis was 112+9kJ. At pH 5.8 and room temperature, addition of humic acids (50gl(-1)) increased the rate of hydrolysis tenfold, while addition of kaolinite or goethite (100-250gl(-1)) both decreased the rate considerably. No significant sorption to soil components could be observed. The degradation rates of dhurrin in top and subsoils of Oxisols, Ultisols, Alfisols and Mollisols were studied at 22 degrees C (25mgl(-1), soil:liquid 1:1 (w:V), pH 3.8-8.1). Half-lives were 0.25-2h for topsoils, and 5-288h in subsoils. Hydrolysis in solution explained up to 45% of the degradation in subsoils whereas the contribution in topsoils was less than 14%, indicating the importance of enzymatic degradation processes. The highest risk of dhurrin leaching will take place when the soil is a low activity acid shallow soil with low content of clay minerals, iron oxides and humic acids.     

氨水循环增强电动力学技术去除土壤中的氟

为了探讨氨水增强电动力学技术修复氟污染土壤的效果及对土壤pH值的影响,在自制的电动力学装置中,1 V/cm电解电压下,以氨水作电解液,采用连续循环的方式进行研究。结果显示,氨水连续循环不仅增大了修复过程中的电流值,且使通过土壤的电流更加稳定,在提高土壤氟迁移效率的同时降低了能耗。在设定的浓度中(0、0.01、0.1和0.2 mol/L),土壤氟的去除率随着氨水浓度的升高而增加,0.2 mol/L氨水具有最大电流值26.8 mA,土壤氟的去除率也达到57.9%,氨水循环增强时两极土壤pH值差异减小。采用氨水循环增强电动力学技术,可有效修复氟污染土壤,土壤中剩余氨还可以提高土壤肥力。     

Kinetics of nitrosation of the herbicide glyphosate.

The herbicide glyphosate was nitrosated by third-order kinetics to N-nitrosoglyphosate. The nitrosation at 25 degrees C was maximum at the reaction pH of 2.5 and had a pH-dependent rate constant of 2.43 M-2 sec-1. An activation energy of 9.5 kcal mole-1 also suggested that glyphosate is nitrosated very readily. Thiocyanate increased the rate 4.6 fold. The possibility of using these results to predict the formation of N-nitrosoglyphosate under normal agricultural practice is discussed.     

Oxidation of MCPA and 2,4-D by UV radiation, ozone, and the combinations UV/H2O2 and O3/H2O2

The phenoxyalkyl acid derivative herbicides MCPA (4-chloro 2-methylphenoxyacetic acid) and 2,4-D (2,4-dichlorophenoxyacetic acid) were oxidized in ultrapure water by means of a monochromatic UV irradiation and by ozone, as well as by the combinations UV/H2O2 and O3/H2O2. In the direct photolysis of MCPA, the quantum yield at 20 degrees C was directly evaluated and a value of 0.150 mol Eins(-1) was obtained in the pH range 5-9, while a lower value of 0.41 x 10(-2) mol Eins(-1) was determined at pH=3. Similarly, for 2,4-D a value of 0.81 x 10(-2) mol Eins(-1) was deduced, independent of the pH of work. The influence of the additional presence of hydrogen peroxide was established in the combined process UV/H2O2, and the specific contribution of the radical pathway to the global photo-degradation was evaluated. The oxidation by ozone and by the combination O3/H2O2 was also studied, with the determination of the rate constants for the reactions of both herbicides with ozone and hydroxyl radicals at 20 degrees C. These rate constants for the direct reactions with ozone were 47.7 and 21.9 M(-1) s(-1) for MCPA and 2,4-D respectively, while the found values for the rate constants corresponding to the radical reactions were 6.6 x 10(9) and 5.1 x 10(9) M(-1) s(-1).     

Chlorination of bisphenol A: kinetics and by-products formation

The kinetics of initial chlorination of bisphenol A (BPA) was studied between pH 2 and 11 at room temperature (20 +/- 2 degrees C). pH Profile of the apparent second-order rate constant of the reaction of BPA with chlorine were modeled considering the elementary reactions of HOCl with BPA species and an acid-catalyzed reaction. The predominant reactions at near neutral pH were the reactions of HOCl with the two phenolate species of BPA (k = 3.10 x 10(4) M(-1)s(-1) for BPA- and 6.62 x 10(4) M(-1) s(-1) for BPA(2-)). At near neutral pH, half-life times of BPA were calculated to be less than 1.5 h for chlorine residual higher than 0.2 mg l(-1). Chlorination of synthetic treated waters spiked with BPA showed that BPA disappeared within 4 h and that chlorinated bisphenol A congeners were rapidly formed and remained in solution for up to 10-20 h when low chlorine dosages are applied (0.5-1 mg l(-1)). To limit their presence in drinking water networks, it is then necessary to maintain high chlorine residuals that rapidly produce and decompose chlorinated bisphenol A congeners.     

Hydrodechlorination of dichlorobiphenyls over Ni-Mo/Al2O3 catalysts prepared by spray-drying method

The hydrodechlorination (HDCl) process of 2,3-, 2,4- and 2,5-dichlorobiphenyls was studied over a sulphided Ni-Mo/Al(2)O(3) catalyst in a stirred autoclave at a hydrogen pressure of 3 MPa. The catalysts were prepared by spray-drying. They were characterized by N(2) adsorption, thermogravimetry and scanning electron microscopy with X-ray microanalysis. The reaction temperature of the catalytic HDCl process was varied in the range of 230-290 degrees C. Polychlorinated biphenyls (PCBs) free transformer oil was used as reaction medium. The HDCl degree of dichlorobiphenyl isomers was in the range of 82-93%. The efficiency in the chlorine removal was found to be related to the position of the substituted chlorine atom and decreased as follows 2,4-dichlorobiphenyl approximately 2,5-dichlorobiphenyl>2,3-dichlorobiphenyl. For comparison, the HDCl process of 2,3-dichlorobiphenyl (2,3-PCB) without catalyst was also studied. The chlorine removal was 85% for the catalytic HDCl of 2,3-PCB whereas non-catalytic process led only to 16% of dechlorination in the same operating conditions, i.e. at 290 degrees C after 120 min. Monodichlorobiphenyls were not detected in the reaction products. The data for both catalytic and non-catalytic conversion of 2,3-PCB fit to a first-order model. Kinetic constants and the activation energy of the overall HDCl reaction of 2,3-PCB to biphenyl were evaluated. Compared to non-catalytic process, a nearly threefold decrease in the activation energy was observed in the presence of Ni-Mo/Al(2)O(3) catalyst prepared by spray-drying (48 kJ mol(-1) vs. 124 kJ mol(-1)).     

Removal mechanism of endosulfan sorption onto wood charcoal

Endosulfan is among the most widely used pesticides in developing countries and other parts of the world and has been found to contaminate various parts of the environment, including drinking water sources. In an earlier study to find a suitable adsorbent to remove endosulfan, wood charcoal was found to give promising results. In the present study, the process controlling the rate of endosulfan sorption onto wood charcoal and the mechanism of removal were examined using various methodologies. Both film and pore diffusion coefficients were determined, and the linearity of the rate constants of adsorption with initial endosulfan concentrations revealed the process to be controlled by film diffusion. This was supported by the linear fit of the rate constants with the inverse of the diameter of adsorbent particles and the change in adsorption rates with agitation speed. Multiple interruption tests also revealed that endosulfan sorption onto wood charcoal is controlled by film diffusion. The increase in reaction rate constant with temperature and isosteric heat of adsorption in the range of -2.655 to 5.185 kcal/mol implied that the endosulfan removal process was endothermic in nature. The activation energy of 2.33 kcal/mol, which was less than 12 kcal/mol, revealed that the removal mechanism could be attributed to physisorption with a major contribution of van der Waals and electrostatic forces.     

Sonochemical degradation of 2,3,7,8-tetrachlorodibenzo-p-dioxins in aqueous solution with Fe(III)/UV system

2,3,7,8-Tetrachlorodibenzo-p-dioxin (2,3,7,8-TeCDD) was rapidly decreased by sonication in aqueous solution. The degradation efficiency was strongly influenced by ultrasonic power and reaction temperature. An initial 2,3,7,8-TeCDD concentration of 20 ng l(-1) was completely degraded within 60 min under sonochemical conditions using a 20 kHz frequency with a 150 W ultrasound power. The activation energy is 21.9 kJ/mol in the temperature range of 10-40 degrees C, suggesting a diffusion-controlled reaction. To increase the efficiency of 2,3,7,8-TeCDD treatment, degradation system combined ultrasound with Fe(III) (2 x 10(-4)mol l(-1)) and UV irradiation. Both UV and Fe(III) induced Fenton, Fenton-like and photo-Fenton reactions, leading to additional OH radicals and rapid 2,3,7,8-TeCDD removal.     

Polychlorinated dibenzo-dioxins and -furans detoxification of soil promoted by K-polyethylene glycol technology

The detoxification of soil and sludge from polychlorinated dibenzo-dioxins (PCDD) and -furans (PCDF) has been achieved by means of the K-PEG technology based on the in situ formation of the complex between polyethylene glycol (PEG) and KOH. Dechlorination of the pollutants was promoted by heating the samples up to 250 degrees C, above the PEG thermal degradation onset (>140 degrees C). As a consequence, a bursting evolution of hydrogen was observed which gave a reductive character to the reaction media and atmosphere. PCDD and PCDF chlorine atoms were progressively eliminated by a hydrodehalogenation reaction. After optimisation of the experimental parameters, the toxicity index was lowered more than 98%. In order to gain insight on the mechanism of the reaction, PEG thermal degradation chemistry was studied in some detail. The analytical results (mainly by mass and IR spectroscopy) suggest that PEG has an essential role on promoting the dehalogenation reaction by acting as a phase transfer agent as well as a source of hydride.     

Influence of pH on persulfate oxidation of TCE at ambient temperatures

In situ chemical oxidation (ISCO) is a technology used for groundwater remediation. This laboratory study investigated the use of the oxidant sodium persulfate for the chemical oxidation of trichloroethylene (TCE) at near ambient temperatures (10, 20 and 30 degrees C) to determine the influence of pH (pH=4, 7 and 9) on the reaction rate (i.e., pseudo-first-order rate constants) over the range of temperatures utilized. TCE solutions (60 mg l(-1); 0.46 mM) were prepared in phosphate buffered RO water and a fixed persulfate/TCE molar ratio of 50/1 was employed in all tests. Half-lives of TCE degradation at 10, 20 and 30 degrees C (pH 7) were 115.5, 35.0 and 5.5h, respectively. Maximum TCE degradation occurred at pH 7. Lowering system pH resulted in a greater decrease in TCE degradation rates than increasing system pH. Radical scavenging tests used to identify predominant radical species suggested that the sulfate radical (SO(4)(.-)) predominates under acidic conditions and the hydroxyl radical (.OH) predominates under basic conditions. In a side by side comparison of TCE degradation in a groundwater vs. unbuffered RO water it was demonstrated that when the system pH is buffered to near neutral pH conditions due to the presence of natural occurring groundwater constituents that the TCE degradation rate is higher than in unbuffered RO water where the system pH dropped from 5.9 to 2.8. The results of this study suggest that in a field application of ISCO, pH should be monitored and adjusted to near neutral if necessary.     

Kinetic assessment of the potassium ferrate(VI) oxidation of antibacterial drug sulfamethoxazole

Sulfamethoxazole (SMX), a worldwide-applied antibacterial drug, was recently found in surface waters and in secondary wastewater effluents, which may result in ecotoxical effects in the environment. Herein, removal of SMX by environmentally-friendly oxidant, potassium ferrate(VI) (K(2)FeO(4)), is sought by studying the kinetics of the reaction between Fe(VI) and SMX as a function of pH (6.93-9.50) and temperature (15-45 degrees C). The rate law for the oxidation of SMX by Fe(VI) is first-order with respect to each reactant. The observed second-order rate constant decreased non-linearly from 1.33+/-0.08 x 10(3) M(-1)s(-1) to 1.33+/-0.10 x 10(0) M(-1)s(-1) with an increase of pH from 7.00 to 9.50. This is related to protonation of Fe(VI) (HFeO(4)(-) <==> H(+) + FeO(4)(2-); pK(a,HFeO(4)) = 7.23) and sulfamethoxazole (SH <==> H(+) + S(-); pK(a,SH)=5.7). The estimated rate constants were k(11)(HFeO(4)(-) + SH) = 3.0 x 10(4) M(-1)s(-1), k(12)(HFeO(4)(-) + S(-)) = 1.7 x 10(2) M(-1)s(-1), and k(13) (FeO(4)(2-) + SH) = 1.2 x 10(0) M(-1)s(-1). The energy of activation at pH 7.0 was found to be 1.86+/-0.04 kJ mol(-1). If excess potassium ferrate(VI) concentration (10 microM) is used than the SMX in water, the half-life of the reaction using a rate constant obtained in our study would be approximately 2 min at pH 7. The reaction rates are pH dependent; thus, so are the half-lives of the reactions. The results suggest that K(2)FeO(4) has the potential to serve as an oxidative treatment chemical for removing SMX in water.     

Dehalogenation potential of municipal waste incineration fly ash

BACKGROUND, AIMS AND SCOPE: It is well known that the fly ash from filters of municipal waste incinerators (MWI-FA) shows dehalogenation properties after heating it to 240-450 degrees C. However, this property is not general, and fly ash samples do not possess dehalogenation ability at all in many cases. Fly ash has a very variable composition, and the state of the fly ash matter therefore plays the decisive role. In the present paper, the function of important components responsible for the dehalogenation activity of MWI-FA is analysed and compared with the model fly ash. METHODS: With the aim of accounting for the dehalogenation activity of MWI-FA, the following studies of hexachlorobenzene (HCB) dechlorination were performed: The role of copper in dehalogenation experiments was evaluated for five types of metallic copper. The gasification of carbon in MWI-FA was studied in the 250-350 degrees C temperature range. Five different kinds of carbon were used, combined with conventional Cu(o) and activated nanosize copper powder. The dechlorination experiments were also carried out with Cu(II) compounds such as CuO, Cu(OH)2, CuCl2 and CuSO4. The results were discussed from the standpoint of thermodynamics of potential reactions. Based on these results, the model of fly ash was proposed, containing silica gel, metallic copper and carbon. The dechlorination ability of MWI-FA and the model fly ash are compared under oxygen-deficient atmosphere. CONCLUSIONS: The results show that, under given experimental conditions, copper acts in the dechlorination as a stoichiometric agent rather than as a catalyst. The increased surface activity of copper enhances its dechlorination activity. It was found further that the presence of copper leads to a decrease in the temperature of carbon gasification. The cyclic valence change from Cu(o) to Cu+ or Cu2+ is a prerequisite for the dehalogenation to take place. RECOMMENDATION AND OUTLOOK: Thermodynamic analysis of the dechlorination effect, as well as the comparison of dechlorination pathways on MWI-FA and model fly ash, can provide a deeper understanding of the studied reaction.