Performance and exhaust emission characteristics investigation of compression ignition engine fuelled with microalgae biodiesel and its diesel blends

Biofuels extracted from plant biomass can be used as fuel in CI engines to lower a hazardous atmospheric pollutant and mitigate climate risks. Furthermore, its implementation is hampered by inevitable obstacles such as feedstocks and the crop area required for their cultivation, leading to a lack of agricultural land for the expansion of food yields. Despite this, microalgae have been discovered to be the most competent and unwavering source of biodiesel due to their distinguishing characteristics of being non-eatable and requiring no cropland for cultivation. The objectives of this paper was to look into the potential of a novel, formerly underappreciated biodiesel from microalgae species which could be used as a fuel substitute. Transesterification is being used to extract the biodiesel. Microalgae are blended with petroleum diesel in percentage to create microalgae blends (MAB) as needed for experimentation. The impact of biodiesel on performance as well as exhaust emission attributes of a 1-cylinder diesel engine was experimentally studied. Compared to petroleum diesel, different blend of microalgae biodiesel showed a decline in torque and hence brake power, resulting in an average fall of 7.14 % in brake thermal efficiency and 11.54 % increase in brake-specific fuel consumption. There were wide differences in exhaust emission characteristics, including carbon monoxide and hydrocarbon, as the blend ratio in diesel increased. Moreover, nitrogen oxides and carbon dioxides increase in all algae biodiesel blends, but they are still within the acceptable range of petroleum diesel.

     

A comparison of acute toxicity of biodiesel, biodiesel blends, and diesel on aquatic organisms

The increased demand of alternative energy sources has created interest in biodiesel and biodiesel blends; biodiesel is promoted as a diesel substitute that is safer, produces less harmful combustion emissions, and biodegrades more easily. Like diesel spills, biodiesel can have deleterious effects on the aquatic environments. The effect of neat biodiesel, biodiesel blends, and diesel on Oncorhynchus mykiss and Daphnia magna was evaluated using acute toxicity testing. Static nonrenewal bioassays of freshwater organisms containing B100, B50, B20, B5, and conventional diesel fuel were used to compare the acute effects of biodiesel to diesel. Mortality was the significant end point measured in this study; percent mortality and lethal concentration (LC50) at different exposure times were determined from the acute toxicity tests performed. Trials were considered valid if the controls exhibited > 90% survival. Based on percentage of mortality and LC50 values, a toxicity ranking of fuels was developed.     

Effects of low concentration biodiesel blend application on modern passenger cars. Part 1: Feedstock impact on regulated pollutants, fuel consumption and particle emissions

Five biodiesels from different feedstocks (rapeseed, soy, sunflower, palm, and used fried oils) blended with diesel at 10% vol. ratio (B10), were tested on a Euro 3 common-rail passenger car. Limited effects (−2% to +4%) were observed on CO₂ emissions. CO and HC emissions increased between 10% and 25% on average, except at high speed - high power where emissions were too low to draw conclusions. NOx emissions increased by up to 20% for two out of the five blends, decreased by up to 15% for two other blends, and remained unchanged for one blend. Particulate matter (PM) was reduced for all blends by up to 25% and the reductions were positively correlated with the extent of biodiesel saturation. PM reductions are associated with consistent reductions in non-volatile particle number. A variable behaviour in particle number is observed when volatile particles are also accounted.     

Comparison of on-road emissions for B-0, B-10, and B-20 in transit buses

Biodiesels are often marketed as being cleaner than regular diesel for emissions. Emission test results depend on the biodiesel blend, but laboratory tests suggest that biodiesels decrease particulate matter, carbon monoxide, hydrocarbons, and air toxins when compared to regular diesel. Results for the amount of oxides of nitrogen (NOx) have been less conclusive. Tests have also not evaluated the commonly available ranges of biodiesel blends in the laboratory. Additionally, little information is available from on-road studies, so the effectiveness of using biodiesels to reduce actual emissions is unknown. A more complex relationship exists between engine operation and the rate of emission production than is typically evaluated using engine or chassis dynamometer tests. On-road emissions can vary dramatically because emissions are correlated to engine mode. Additionally, activity such as idling, acceleration, deceleration, and operation against a grade can produce higher emissions than more stable engine operating modes. Because these modes are not well captured in a laboratory environment, understanding on-road relationships is critical in evaluating the emissions reductions that may be possible with biodiesels. More tests and quantifications of the effects of different blends on engine and vehicle performance are required to promote widespread use of biodiesel. The objective of this research was to conduct on-road tests to compare the emission impacts of different blends of biodiesel to regular diesel fuel under different operating conditions. The team conducted on-road tests that utilized a portable emissions monitoring system that was used to instrument transit buses. Regular diesel and different blends of biodiesel were evaluated during on-road engine operation by instrumenting three in-use transit buses, from the CyRide system of Ames, Iowa, along an existing transit route.     

Seasonal impact of blending oxygenated organics with gasoline on motor vehicle tailpipe and evaporative emissions.

Emissions from a 1988 GM Corsica with adaptive learning closed loop control were measured with 4 fuels at 40, 75, and 90 degrees F. Evaporative and exhaust emissions were examined from each fuel at each test temperature. Test fuels were unleaded summer grade gasoline; a blend of this gasoline containing 8.1 percent ethanol; a refiner's blend stock; and the blend stock containing 16.2 percent methyl tertiary butyl ether. The ethanol and MTBE blends contained 3.0 percent oxygen by weight. Regulated emissions (total hydrocarbons, carbon monoxide, and oxides of nitrogen), detailed aldehydes, detailed hydrocarbons, ethanol, MTBE, benzene, and 1,3-butadiene were determined. The highest levels of regulated emissions were produced at the lower temperature. Blended fuels produced almost twice the evaporative hydrocarbon emissions at high temperatures as did the base fuels. Benzene emissions varied with fuels and operating temperatures, while 1,3-butadiene emissions decreased slightly with increasing temperatures. Formaldehyde emissions were not sensitive to fuel or temperature changes. Ethanol fuel blend total aldehyde emissions increased by 40 percent due to increased acetaldehyde emissions. Fuel blends had approximately a 3 percent economy decrease. The MTBE fuel blend appeared to offer the most reduction in total hydrocarbon, carbon monoxide, and oxides of nitrogen for the fuels and temperatures tested.     

An experimental study on usage of plastic oil and B20 algae biodiesel blend as substitute fuel to diesel engine

Usage of plastics has been ever increasing and now poses a tremendous threat to the environment. Millions of tons of plastics are produced annually worldwide, and the waste products have become a common feature at overflowing bins and landfills. The process of converting waste plastic into value-added fuels finds a feasible solution for recycling of plastics. Thus, two universal problems such as problems of waste plastic management and problems of fuel shortage are being tackled simultaneously. Converting waste plastics into fuel holds great promise for both the environmental and economic scenarios. In order to carry out the study on plastic wastes, the pyrolysis process was used. Pyrolysis runs without oxygen and in high temperature of about 250–300 °C. The fuel obtained from plastics is blended with B20 algae oil, which is a biodiesel obtained from microalgae. For conducting the various experiments, a 10-HP single-cylinder four-stroke direct-injection water-cooled diesel engine is employed. The engine is made to run at 1500 rpm and the load is varied gradually from 0 to 100 %. The performance, emission and combustion characteristics are observed. The BTE was observed to be higher with respect to diesel for plastic-biodiesel blend and biodiesel blend by 15.7 and 12.9 %, respectively, at full load. For plastic-biodiesel blend, the emission of UBHC and CO decreases with a slight increase in NO _x as compared to diesel. It reveals that fuel properties are comparable with petroleum products. Also, the process of converting plastic waste to fuel has now turned the problems into an opportunity to make wealth from waste.     

Seasonal Impact of Blending Oxygenated Organics with Gasoline on Motor Vehicle Tailpipe and Evaporative Emissions

Emissions from a 1988 GM Corsica with adaptive learning closed loop control were measured with 4 fuels at 40, 75, and 90° F. Evaporative and exhaust emissions were examined from each fuel at each test temperature. Test fuels were unleaded summer grade gasoline; a blend of this gasoline containing 8.1 percent ethanol; a refiner’s blend stock; and the blend stock containing 16.2 percent methyl tertiary butyl ether. The ethanol and MTBE blends contained 3.0 percent oxygen by weight. Regulated emissions (total hydrocarbons, carbon monoxide, and oxides of nitrogen), detailed aldehydes, detailed hydrocarbons, ethanol, MTBE, benzene, and 1, 3-butadiene were determined.

The highest levels of regulated emissions were produced at the lower temperature. Blended fuels produced almost twice the evaporative hydrocarbon emissions at high temperatures as did the base fuels. Benzene emissions varied with fuels and operating temperatures, while 1, 3-butadiene emissions decreased slightly with increasing temperatures. Formaldehyde emissions were not sensitive to fuel or temperature changes. Ethanol fuel blend total aldehyde emissions Increased by 40 percent due to increased acetaldehyde emissions.

Fuel blends had approximately a 3 percent economy decrease. The MTBE fuel blend appeared to offer the most reduction in total hydrocarbon, carbon monoxide, and oxides of nitrogen for the fuels and temperatures tested.     

Regulated emissions from biodiesel fuels from on/off-road applications

This research is one of the largest studies of biodiesel in both on-road and off-road uses. The testing was conducted for the military and encompassed a wide range of application types including two medium-duty trucks, two Humvees, a heavy heavy-duty diesel truck, a bus, two stationary backup generators (BUGs), a forklift, and an airport tow vehicle. The full range of fuels tested included a California ultra-low sulfur diesel (ULSD) fuel, different blend ratios of two different yellow-grease biodiesels and one soy-based biodiesel, JP-8, and yellow-grease biodiesel blends with two different NO_x reduction additives. The B20-YGA, B20-YGB, and B20-Soy did not show trends relative to ULSD that were consistent over all applications tested. Higher biodiesel blends were tested on only one vehicle, but showed a tendency for higher total hydrocarbons (THC) and carbon monoxide (CO) emissions and lower particulate matter (PM) emissions. The JP-8 showed increases in THC and CO relative to the ULSD.     

水中柴油污染物的微生物降解及其动力学

以混合柴油为靶污染物,通过对比实验研究了油污染物在模拟水环境中的降解效果。研究表明,模拟自然条件下混合柴油污染物总体降解较慢,油质去除率低;生物强化降解条件下,向混合柴油污染水样中添加驯化培养的微生物混合菌群,生物降解速率明显提高,油质去除率达到98%以上。研究还发现,各污染水样中油的降解速率与降解效果随柴油的配比而不同,混合柴油样本中生物柴油的比例越高,样本的降解率越高,表明生物柴油作为碳源有效改善了水中有机营养配比,促进了柴油的去除效果。进一步分析表明,混合柴油在水中的降解过程符合一级反应动力学,生物强化降解条件下,生物柴油比例越高,混合柴油降解速率越快,除油微生物以菌胶团、球菌和丝状菌为主。     

Effect of start of main injection timing on performance,emission, and combustion characteristics of a VGT CI engine fueled with neem biodiesel

The performance of engine parameters is more influenced with fuel injection strategies namely start of main injection timing (SoMI). An experimental analysis was performed to find the optimum SoMI timing based on performance, emission, and combustion characteristics. Base fuel of diesel and neem biodiesel was used as test fuels. The neem biodiesel was prepared by esterification and transesterification process. It is found from literature that neem biodiesel blend NB20 with diesel gives optimum performance and emission characteristics; therefore, NB20 blend was used for experiments. A variable geometry turbocharger (VGT) compression ignition (CI) engine was used to conduct the experiments. Engine performance parameters were estimated and compared with a base fuel of diesel and with NB20 blends. In this experimentation, fuel injection pressure (FIP) of 800 bar and engine speed of 1700 rpm were considered. SoMI timing was varied from 2° to 10° bTDC with an increment of 2° bTDC timing. Cylinder pressure (CP) and heat release rate (HRR) were estimated and found that are higher for diesel fuel compared to NB20 blend at different SoMI timings. The addition of neem biodiesel NB20 blend to diesel fuel decreases the exhaust emissions except NOx emissions. The BSFC was considerably reduced and BTE was improved almost equivalent to the diesel fuel for NB20. From the results, it is concluded that 10° bTDC SoMI timing provides 13% improvement in BTE, 21% decrement in BSFC, and 7.5% reduction in CO₂ emissions.

     

Particulate Emissions from a Stationary Engine Fueled with Ultra-Low-Sulfur Diesel and Waste-Cooking-Oil-Derived Biodiesel

ABSTRACT

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture.

IMPLICATIONS There has been an increased usage of stationary diesel engines, especially backup power generators to meet the growing energy demand. Biodiesel derived from waste cooking oil has received increasing attention as an alternative fuel. However, data are only sparsely available in the literature on particulate emissions from stationary engines, fueled with blends of diesel and biodiesel. This study provides insights into the influence of waste-cooking-oil-derived biodiesel on engine performance and the particulate emissions from a stationary engine. The results of the study form a scientific basis to evaluate the impact of biodiesel emissions on the environment and human health.     

Influence of constant and fluctuating temperature on biodegradation rates of fish biodiesel blends contaminating Alaskan sand

Bioremediation of sandy soil contaminated with fish-biodiesel, conventional diesel, and blends of both was studied in microcosm experiments at different temperatures, simulating the subarctic environment. While distinct lag, exponential, and stationary phases were observed at 20 °C, degradation at 6 °C was slow and the lag phase continued throughout the 4-week experiment. A three-phase 1st order kinetic model successfully described respiration at 20 °C, a one-phase model was sufficient at 6 °C. For temperatures fluctuating between ∼6 and ∼20 °C, higher than expected microbial activity persisted at 6 °C for several days, due to the presence of active cultures, even though the soil temperature closely followed the air temperature. At 20 °C, respiration peaked already after 1 week, and 18-51% of the initially added fuel was mineralized within 4 weeks, whereby degradation was higher at higher biodiesel percentages. Biodiesel addition accelerated mineralization of blends with regular diesel beyond expectations. In blends with 20% biodiesel, the degradation rate constant was twice as high as for conventional diesel. These synergistic effects are likely due to an active microbial population. Addition of biodiesel to conventional diesel could reduce the impact of diesel spills.     

Hydrocarbon emissions speciation in diesel and biodiesel exhausts

Diesel engine emissions are composed of a long list of organic compounds, ranging from C₂ to C₁₂₊, and coming from the hydrocarbons partially oxidized in combustion or produced by pyrolisis. Many of these are considered as ozone precursors in the atmosphere, since they can interact with nitrogen oxides to produce ozone under atmospheric conditions in the presence of sunlight. In addition to problematic ozone production, Brookes, P., and Duncan, M. [1971. Carcinogenic hydrocarbons and human cells in culture. Nature.] and Heywood, J. [1988. Internal Combustion Engine Fundamentals.Mc Graw-Hill, ISBN 0-07-1000499-8.] determined that the polycyclic aromatic hydrocarbons present in exhaust gases are dangerous to human health, being highly carcinogenic.The aim of this study was to identify by means of gas chromatography the amount of each hydrocarbon species present in the exhaust gases of diesel engines operating with different biodiesel blends. The levels of reactive and non-reactive hydrocarbons present in diesel engine exhaust gases powered by different biodiesel fuel blends were also analyzed.Detailed speciation revealed a drastic change in the nature and quantity of semi-volatile compounds when biodiesel fuels are employed, the most affected being the aromatic compounds. Both aromatic and oxygenated aromatic compounds were found in biodiesel exhaust. Finally, the conservation of species for off-side analysis and the possible influence of engine operating conditions on the chemical characterization of the semi-volatile compound phase are discussed.The use of oxygenated fuel blends shows a reduction in the Engine-Out emissions of total hydrocarbons. But the potential of the hydrocarbon emissions is more dependent on the compositions of these hydrocarbons in the Engine-Out, to the quantity; a large percent of hydrocarbons existing in the exhaust, when biodiesel blends are used, are partially burned hydrocarbons, and are interesting as they have the maximum reactivity, but with the use of pure biodiesel and diesel, the most hydrocarbons are from unburned fuel and they have a less reactivity. The best composition in the fuel, for the control of the hydrocarbon emissions reactivity, needs to be a fuel with high-saturated fatty acid content.     

Particulate emissions from a stationary engine fueled with ultra-low-sulfur diesel and waste-cooking-oil-derived biodiesel

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture.     

Application of artificial neural network for prediction of Pb(II) adsorption characteristics

The adsorption of Pb(II) onto the surface of microwave-assisted activated carbon was studied through a two-layer feedforward neural network. The activated carbon was developed by microwave activation of Acacia auriculiformis scrap wood char. The prepared adsorbent was characterized by using Brunauer–Emmett–Teller (BET) surface area analyzer, scanning electron microscope (SEM), and X-ray difractometer. In the present study, the input variables for the proposed network were solution pH, contact time, initial adsorbate concentration, adsorbent dose and temperature, whereas the output variable was the percent Pb(II) removal. The network had been trained by using different algorithms and based on the lowest mean squared error (MSE) value and validation error, resilient backpropagation algorithm with 12 neurons in the hidden layer was selected for the present investigation. The tan sigmoid and purelin transfer function were used in the hidden and the output layers of the proposed network, respectively. The model predicted and experimental values of the percent Pb(II) removal were also compared and both the values were found to be in reasonable agreement with each other. The performance of the developed network was further improved by normalizing the experimental data set and it was found that after normalization, the MSE and validation error were reduced significantly. The sensitivity analysis was also performed to determine the most significant input parameter.     

Regulated and unregulated emissions from a diesel engine fueled with biodiesel and biodiesel blended with methanol

Experiments were carried out on a diesel engine operating on Euro V diesel fuel, pure biodiesel and biodiesel blended with methanol. The blended fuels contain 5%, 10% and 15% by volume of methanol. Experiments were conducted under five engine loads at a steady speed of 1800 rev min⁻¹ to assess the performance and the emissions of the engine associated with the application of the different fuels. The results indicate an increase of brake specific fuel consumption and brake thermal efficiency when the diesel engine was operated with biodiesel and the blended fuels, compared with the diesel fuel. The blended fuels could lead to higher CO and HC emissions than biodiesel, higher CO emission but lower HC emission than the diesel fuel. There are simultaneous reductions of NO_x and PM to a level below those of the diesel fuel. Regarding the unregulated emissions, compared with the diesel fuel, the blended fuels generate higher formaldehyde, acetaldehyde and unburned methanol emissions, lower 1,3-butadiene and benzene emissions, while the toluene and xylene emissions not significantly different.     

Effects of low concentration biodiesel blends application on modern passenger cars. Part 2: Impact on carbonyl compound emissions

Today in most European member states diesel contains up to 5% vol biodiesel. Since blending is expected to increase to 10% vol, the question arises, how this higher mixing ratio will affect tailpipe emissions particularly those linked to adverse health effects. This paper focuses on the impact of biodiesel on carbonyl compound emissions, attempting also to identify possible relationship between biodiesel feedstock and emissions. The blends were produced from five different feedstocks, commonly used in Europe. Measurements were conducted on a Euro 3 common-rail passenger car over various driving cycles. Results indicate that generally the use of biodiesel at low concentrations has a minor effect on carbonyl compound emissions. However, certain biodiesels resulted in significant increases while others led to decreases. Biodiesels associated with increases were those derived from rapeseed oil (approx. 200%) and palm oil (approx. 180%), with the highest average increases observed at formaldehyde and acroleine/acetone.     

Remediation of a biodiesel blend-contaminated soil by using a modified Fenton process

A soil contaminated with a B20 biodiesel blend (20 % biodiesel, 80 % diesel) has been treated by modified Fenton process with or without chelant addition. All experiments were conducted without pH adjustment. The reagents used were as follows: hydrogen peroxide as oxidant (400–4,000 mmol L^?1), ferric ion as catalyst (5–20 mmol L^?1), and trisodium citrate (50 mmol L^?1) as chelating agent. Soil was spiked at two different pollutant concentrations (1,000–10,000 mg diesel kg^?1 soil). Higher total petroleum hydrocarbon (TPH) removal efficiencies were obtained (up to 75 %) after the treatment in the absence of the chelant due to the low pH obtained in this case. In the presence of chelant, the TPH conversion obtained was lower because both higher pH is obtained and chelant competes with diesel for the oxidant. On the other hand, at neutral pH, the lifetime of the oxidant was increased. Fatty acid methyl esters (FAMEs) are easier to remove than diesel aliphatic hydrocarbons from the blend. An important decrease of the aqueous phase toxicity was observed after the modified Fenton reaction, supporting that nontoxic by-products were released to the aqueous phase during the treatment.     

Effect of additives on the stability of ethanol-diesel blends for IC engine application

The present research work was conducted on a compression ignition engine to assess the engine characteristics fueled with the blend of diesel and high-oxygenated additives such as ethanol. Ethanol does not easily blend with diesel. In order to attain a homogeneous mixture, a small amount of additive is added to the blend. Different additives were added to the blend to form a homogeneous mixture. Stability test was conducted on the blend to ensure prolonged homogeneity. The additives used for the test purpose were isopropanol, oleic acid, and ethylene acetate. From the stability results, it was found that oleic acid was the best additive which produces a better homogenous mixture for the blend of ethanol and diesel. One percentage of oleic acid is used as an additive to blend ethanol and diesel. The different combinations of blend ratios used for the test purpose were D90E10, D80E20, and D70E30. All the aforementioned blends have low cetane number because of ethanol, which was compensated by adding 1% DEE (diethyl ether) to all the blends. Experimental results exhibit that there is an improvement in the performance characteristics, such as brake thermal efficiency (BTE) and specific energy consumption (SEC), with the enrichment of DEE in ethanol-diesel blend. It is also noticed that the blend without DEE exhibited lower magnitude. This is mainly due to higher energy content and cetane number of DEE. Emission characteristics, like hydrocarbon (HC) and carbon monoxide (CO), were found to drastically increase with the increase in the ethanol concentration in the diesel blend. This is attributed to higher latent heat of vaporization (LHV) of ethanol present in the blend. Combustion pressure and heat release rate of the DEE-enriched ethanol blends were higher by 2.2 % and 2.4 %, respectively, when compared with their corresponding blends without DEE. This is a result of higher volatility of DEE which leads to better combustion.

Graphical abstract

     

Impacts of Biodiesel on Pollutant Emissions of a JP-8–Fueled Turbine Engine

Abstract

The impacts of biodiesel on gaseous and particulate matter (PM) emissions of a JP-8–fueled T63 engine were investigated. Jet fuel was blended with the soybean oil-derived methyl ester biofuel at various concentrations and combusted in the turbine engine. The engine was operated at three power settings, namely ground idle, cruise, and takeoff power, to study the impact of the biodiesel at significantly different pressure and temperature conditions. Particulate emissions were characterized by measuring the particle number density (PND; particulate concentration), the particle size distribution, and the total particulate mass. PM samples were collected for off-line analysis to obtain information about the effect of the biodiesel on the polycyclic aromatic hydrocarbon (PAH) content. In addition, temperature-programmed oxidation was performed on the collected soot samples to obtain information about the carbonaceous content (elemental or organic). Major and minor gaseous emissions were quantified using a total hydrocarbon analyzer, an oxygen analyzer, and a Fourier Transform IR analyzer. Test results showed the potential of biodiesel to reduce soot emissions in the jet-fueled turbine engine without negatively impacting the engine performance. These reductions, however, were observed only at the higher power settings with relatively high concentrations of biodiesel. Specifically, reductions of ～15% in the PND were observed at cruise and takeoff conditions with 20% biodiesel in the jet fuel. At the idle condition, slight increases in PND were observed; however, evidence shows this increase to be the result of condensed uncombusted biodiesel. Most of the gaseous emissions were unaffected under all of the conditions. The biodiesel was observed to have minimal effect on the formation of polycyclic aromatic hydrocarbons during this study. In addition to the combustion results, discussion of the physical and chemical characteristics of the blended fuels obtained using standard American Society for Testing and Materials (ASTM) fuel specifications methods are presented.