Remediation,land use,and risk at Rocky Flats,and a comparison with Hanford

US Department of Energy (US DOE) responsibilities for its former national atomic weapons complex include remediation of the Rocky Flats facility near Denver, Colorado. In 1993, the site's primary mission shifted from “production'' of plutonium components for atomic weapons to cleanup of extensive radioactive and chemical contamination representing the legacy of production activities. Remediation was governed by the agreements between the US DOE as the responsible party and the US Environmental Protection Agency and the state of Colorado as joint regulators. In 1995, the Rocky Flats Future Use Working Group issued its final report, recommending among other features that long‐term cleanup reduce contamination levels to background. This article describes the circumstances that led the US DOE to complete the Rocky Flats cleanup more quickly and makes comparisons to the situation at the US DOE's Hanford site. © 2011 Wiley Periodicals, Inc.     

Continuous water‐level monitoring in the assessment of groundwater remediation and refinement of a conceptual site model

An Erratum has been published for this article in Remediation 16(1) 2005, 155–157. Water‐level data collection is a fundamental component of groundwater investigations and remediation. While the locations and depths of monitored wells are important, the frequency of data collection may have a large impact on conclusions made about site hydrogeology. Data‐logging water‐level probes may be programmed to record water levels at frequent intervals, providing site decision makers with abundant, detailed information on the response of an aquifer to both anticipated and unforeseen stresses. In this study, a network of movable probes has provided several years of hourly water‐ level data. The understanding of the site's phytoremediation system has been enhanced by the continuous data, but subsequent insights into an unexpected situation regarding the site's infrastructure have been the most valuable result of the monitoring program. © 2005 Wiley Periodicals, Inc.     

Utilization of pulverized fuel ash in Malta

In Malta all of the waste produced is mixed and deposited at various sites around the island. None of these sites were purpose built, and all of the waste is above groundwater level. The landfills are not engineered and do not contain any measures to collect leachate and gases emanating from the disposal sites. Another waste, which is disposed of in landfills, is pulverized fuel ash (PFA), which is a by-product of coal combustion by the power station. This has been disposed of in landfill, because its use has been precluded due to the radioactivity of the ashes. The aim of this study was to analyze the chemical composition of the pulverized fuel ash and to attempt to utilize it as a cement replacement in normal concrete mixes in the construction industry. The levels of radiation emitted from the ashes were measured by gamma spectrometry. The results of this study revealed that although at early ages cement replacement by PFA resulted in a reduction in compressive strength (P=0), when compared to the reference concrete at later ages the strengths measured on concrete cores were comparable to the reference concrete (P>0.05). The utilization of PFA up to 20% cement replacement in concrete did not raise the radioactivity of the concrete. In conclusion, utilization of PFA in the construction industry would be a better way of disposing of the ashes rather than controlling the leachate and any radioactivity emitted by the landfilled ashes.     

Incineration risk perceptions and public concern: Experience in the U.K. improving risk communication

Siting decisions for hazardous waste incineration continue to be delayed and impeded by adverse public reaction. Improved public relations and education of the public about risks are the favoured approaches amongst many experts and the industry for allaying public concerns. This paper identifies the limited potential for such strategies and advocates instead attention to the whole risk management system for hazardous waste siting decisions. The paper's conclusions and recommendations arise from an examination of the nature, sources and impact of public concerns about incineration in the U.K.     

In situ remediation of MTBE utilizing ozone

There has been a great deal of focus on methyl tertiary butyl ether (MTBE) over the past few years by local, state, and federal government, industry, public stakeholders, the environmental services market, and educational institutions. This focus is, in large part, the result of the widespread detection of MTBE in groundwater and surface waters across the United States. The presence of MTBE in groundwater has been attributed primarily to the release from underground storage tank (UST) systems at gasoline service stations. MTBE's physical and chemical properties are different than other constituents of gasoline that have traditionally been cause for concern [benzene, toluene, ethylbenzene, and xylenes (BTEX)]. This difference in properties is why MTBE migrates differently in the subsurface environment and exhibits different constraints relative to mitigation and remediation of MTBE once it has been released to subsurface soils and groundwater. Resource Control Corporation (RCC) has accomplished the remediation of MTBE from subsurface soil and groundwater at multiple sites using ozone. RCC has successfully applied ozone at several sites with different lithologies, geochemistry, and concentrations of constituents of concern. This article presents results from several projects utilizing in situ chemical oxidation with ozone. On these projects MTBE concentrations in groundwater were reduced to remedial objectives usually sooner than anticipated. © 2002 Wiley Periodicals, Inc.     

The incineration research facility

The Cincinnati-based Risk Reduction Engineering Laboratory, Office of Research and Development, U.S. EPA operates the Incineration Research Facility (IRF) in Jefferson, Arkansas. This facility's pilot-scale experimental incineration systems include a Rotary Kiln System and a Liquid Injection System. Each system incorporates primary and secondary combustors and associated waste handling equipment, process controllers, safety equipment and air pollution control devices. These “state-of-practice” incinerators are fully permitted to test the entire range of RCRA hazardous wastes normally encountered in the hazardous waste treatment industry. This paper reports the principal features and capabilities of the IRF.     

The Use of Zero‐Valent Iron (ZVI) Technology to Promote DDT and Dieldrin Degradation at Point Pelee National Park

Point Pelee National Park (PPNP) is highly contaminated with dichlorodiphenyltrichloroethane (DDT) and dieldrin due to the historical use of these two persistent organochlorine pesticides. Zero‐valent iron (ZVI) technology with and without amendments has been successfully used in the past to promote organochlorine pesticides degradation in several locations in North America and Europe. In this study, the use of two commercially available ZVI products, DARAMEND^® and EHC^®, to promote DDT and dieldrin degradation in PPNP's soil and groundwater were investigated. DARAMEND^® was applied to PPNP's soil in a laboratory experiment and in an in situ pilot‐scale plot. In both cases, DARAMEND^® did not significantly increase DDT or dieldrin degradation in treated soils. The effectiveness of EHC^® was tested in a laboratory experiment that simulated the park's groundwater environment using PPNP's pesticide contaminated soil. The result was consistent with the one reported for DARAMEND^®, in that there was no significant increase in DDT or dieldrin degradation in any of the samples treated with EHC^®. These results demonstrate that both of these ZVI commercially available products are not suitable for in situ remediation at PPNP.  ©2017 Wiley Periodicals, Inc.     

Valorization of pellets from municipal WWTP sludge in lightweight clay ceramics

A direct result of the growing number of municipal wastewater-treatment plants (WWTPs) has been an increase in the generation of large amounts of sewage sludge that requires environmentally acceptable final destination. To decrease the volume of sludge, a common technique is drying the sludge at a low temperature in rotary kilns. The result of this process is a granulated material consisting of dehydrated sludge pellets.After this treatment, this pelletized material becomes easier to manipulate, but it also becomes a more toxic waste, containing dangerous substances, mostly of the lipid type. At its final stage, this material is usually incinerated, used as a comburent material, used as an agricultural fertilizer, or used in the cement industry. Each application has its own problems and requires remediation measures from the safety and environmental viewpoints.In this study, we looked beyond these possible applications and analyzed the transformation of sewage sludge through a ceramization process into a material similar to expanded clays; we subsequently explored its uses in the building industry or in the agriculture industry, among others. Both the properties of the product material and the production method were characterized, and an environmental analysis was conducted.The new, lightweight material had a microstructure with open porosity and low thermal conductivity. Environmental characterization such as the leaching test revealed that undetectable amounts of hazardous metals from the sludge were present in the leachate after the sludge went through a thermal treatment, despite their initial presence (with the exception of vanadium, which could pose some restrictions on some of the proposed uses for the final product). Toxicity tests also showed negative results. The study of gaseous emissions during production revealed emissions factors similar to those during the production of conventional clay ceramics, although with higher organic emissions. As for conventional clay ceramics, industrial production would require the implementation of some type of air-depuration system. The results showed that the ceramization of sludge pellets is a promising valorization technique worth considering from both the economic and technological perspectives.     

The challenge of remediation technology development

A huge commercial environmental industry, currently estimated at some $130 billion in size in the United States alone, has sprung up to manage and remediate environmental problems. Hundreds of innovative remediation technologies are being developed under EPA's SITE program, which has provided R&D funding for more than 100 new treatment technologies. Despite the obvious demand, numerous regulatory, marketing, technical, and financial barriers have impeded progress in the field of remediation technology development. Developers of remediation technologies are faced with a significant challenge to overcome these barriers and successfully bring a technology to market. This article examines the barriers to technology development and offers strategic planning alternatives for long-term economic success and commercial viability of remediation technologies.     

Factors and values of willingness to pay for improved construction waste management--a perspective of Malaysian contractors

Malaysia is facing an increase in the generation of waste and of accompanying problems with the disposal of this waste. In the last two decades, extensive building and infrastructure development projects have led to an increase in the generation of construction waste material. The construction industry has a substantial impact on the environment, and its environmental effects are in direct relation to the quality and quantity of the waste it generates. This paper discusses general characteristics of the construction contractors, the contractors' willingness to pay (WTP) for improved construction waste management, determining factors which affect the amount of their willingness to pay, and suggestions and policy implications in the perspective of construction waste management in Malaysia. The data in this study is based on contractors registered with the construction industry development board (CIDB) of Malaysia. Employing the open ended contingent valuation method, the study assessed the contractors' average maximum WTP for improved construction waste management to be RM69.88 (1US$=3.6 RM) per tonne of waste. The result shows that the average maximum WTP is higher for large contractors than for medium and small contractors. The highest average maximum WTP value is RM88.00 for Group A (large contractors) RM78.25 for Group B (medium-size contractors) and RM55.80 for Group C (small contractors). One of the contributions of this study is to highlight the difference of CIDB registration grade in the WTP for improved construction waste management. It is found that contractors' WTP for improved waste collection and disposal services increases with the increase in contractors' current paid up capital. The identified factors and determinants of the WTP will assist the formulation of appropriate policies in addressing the construction waste problem in Malaysia and indirectly improve the quality of construction in the country.     

Vapor intrusion mitigation challenges posed by a classic urban setting

AECOM's Environmental Remediation Services Group, under a Pennsylvania Department of Environmental Protection (PADEP) remediation contract, was tasked with assessing potential vapor intrusion risks and mitigating identified risks at an active commercial property affected by a former adjacent laundry and dry cleaning operation. The former dry cleaning operation was positioned in the center of row‐buildings containing various commercial businesses. The neighboring active commercial property is an antiquated building that operates as a coffee shop. The coffee shop building contains a service area, a kitchen, and a rear conference room on the first floor, a storage area on the second floor, and a partial basement. The basement has been observed to periodically flood. Adjacent to the coffee shop building is an operating hair and nail salon that formerly functioned as one of the dry cleaning operations buildings with known soil, groundwater, and soil gas impacts. Due to the disposition of the coffee shop building, a methodical approach was implemented to characterize the potential vapor intrusion risk and included a diagnostic building inspection that identified required management of basement apertures and abatement of periodic flooding prior to vapor intrusion mitigation system design and installation.     

内地与香港燃煤电厂大气污染物排放控制政策与标准比较

香港特区与广东省政府联合成立粤港持续发展与环保合作小组,并发表《改善珠江三角洲空气质量的联合声明》（简称＂减排联合声明＂）,同意制定合理的减排方案,共同执行管理计划。总结分析了粤、港地区在治理燃煤电厂大气污染物方面的控制政策,并对大陆与香港特区燃煤电厂大气污染物的排放标准进行比较。     

Electronic waste (e-waste): material flows and management practices in Nigeria

The growth in electrical and electronic equipment (EEE) production and consumption has been exponential in the last two decades. This has been as a result of the rapid changes in equipment features and capabilities, decrease in prices, and the growth in internet use. This creates a large volume of waste stream of obsolete electrical and electronic devices (e-waste) in developed countries. There is high level of trans-boundary movement of these devices as secondhand electronic equipment into developing countries in an attempt to bridge the 'digital divide'. The past decade has witnessed a phenomenal advancement in information and communication technology (ICT) in Nigeria, most of which rely on imported secondhand devices. This paper attempts to review the material flow of secondhand/scrap electronic devices into Nigeria, the current management practices for e-waste and the environmental and health implications of such low-end management practices. Establishment of formal recycling facilities, introduction of legislation dealing specifically with e-waste and the confirmation of the functionality of secondhand EEE prior to importation are some of the options available to the government in dealing with this difficult issue.     

Fenton's in-situ reagent chemical oxidation of hydrocarbon contamination in soil and groundwater

Industry and regulatory demands for rapid and cost-effective clean up of hydrocarbon and other contamination in soil and groundwater has prompted development and improvement of in-situ remediation technologies. In-situ technologies offer many advantages over ex-situ treatment alternatives, including lower initial capital and long-term operation and maintenance costs, less site disruption, no Resource Conservation and Recovery Act (RCRA) liability, and shorter treatment time necessary to achieve cleanup objectives. Fenton's reagent, a mixture of hydrogen peroxide and ferrous iron that generates a hydroxyl free radical as an oxidizing agent, is widely accepted for chemical oxidation of organic contaminants in the wastewater industry. In-situ implementation of Fenton's reagent for chemical oxidation of organic contaminants in soil and groundwater continues to grow in acceptance and application to a wide variety of environmental contaminants and hydrogeologic conditions (EPA, 1998).     

Determination of Cu and Ni incorporation ratios in Portland cement clinker

Cu and Ni are metals found in galvanic sludges; these sludges are considered hazardous due to their heavy metal content. The main objective of this work is to determine the incorporation amount of Cu and Ni in Portland clinker when a galvanic sludge containing these metals is added to the clinker raw-material. The influence of this addition on the clinkering reactions is evaluated as well as the possibility of co-incinerating galvanic sludges containing Cu and Ni in rotary cement kilns. This study also characterizes the galvanic sludge. Samples were prepared by additions from 0.25 to 5 wt.% of a galvanic sludge to an industrial clinker raw-material. The clinkering process was simulated in a laboratory device. The following techniques were applied to characterize the raw materials and the products of the tests: chemical analysis, differential thermal analysis (DTA) and thermogravimetric analysis (TG). Leaching tests were performed in the produced clinker samples in order to verify the incorporation of the studied metals in the clinker structure. The results led to the conclusion that additions of up to 2 wt.% of a galvanic sludge containing 2.4 wt.%Cu and 1.2 wt.% Ni to clinker raw-material do not affect the clinkering reactions and that these metals are totally incorporated into the clinker.     

Paper waste – Recycling,incineration or landfilling? A review of existing life cycle assessments

A review of existing life cycle assessments (LCAs) on paper and cardboard waste has been undertaken. The objectives of the review were threefold. Firstly, to see whether a consistent message comes out of published LCA literature on optimum disposal or recycling solutions for this waste type. Such message has implications for current policy formulation on material recycling and disposal in the EU. Secondly, to identify key methodological issues of paper waste management LCAs, and enlighten the influence of such issues on the conclusions of the LCA studies. Thirdly, in light of the analysis made, to discuss whether it is at all valid to use the LCA methodology in its current development state to guide policy decisions on paper waste. A total of nine LCA studies containing altogether 73 scenarios were selected from a thorough, international literature search. The selected studies are LCAs including comparisons of different management options for waste paper. Despite claims of inconsistency, the LCAs reviewed illustrate the environmental benefits in recycling over incineration or landfill options, for paper and cardboard waste. This broad consensus was found despite differences in geographic location and definitions of the paper recycling/disposal systems studied. A systematic exploration of the LCA studies showed, however, important methodological pitfalls and sources of error, mainly concerning differences in the definition of the system boundaries. Fifteen key assumptions were identified that cover the three paper cycle system areas: raw materials and forestry, paper production, and disposal/recovery. It was found that the outcome of the individual LCA studies largely depended on the choices made in some of these assumptions, most specifically the ones concerning energy use and generation, and forestry.     

Recent Developments in Cleanup Technologies

Although the reaction mechanics are somewhat mysterious, the use of iron for in situ groundwater treatment has recently gained considerable attention and respect in the remediation industry. The basic scientific principles of both applications of iron have been known for over a century; however, both were nearly unheard of as remediation technologies five years ago. Both technologies have a strong potential for widespread use. They are commercially available, have been proven in field studies, are less expensive than traditional pump and treat technologies, and, in many types of groundwater systems, may be able to meet difficult-to-achieve groundwater treatment standards. As these technologies continue to undergo development, there could be considerably more aggressive applications used to treat ground-water containing high concentrations of chlorinated organics and DNAPLs.     

Incineration treatment of arsenic-contaminated soil

An incineration test program was conducted at the U.S. Environmental Protection Agency's Incineration Research Facility to evaluate the potential of incineration as a treatment option for contaminated soils at the Baird and McGuire Superfund site in Holbrook, Massachusetts. The purpose of these tests was to evaluate the incinerability of these soils in terms of the fate of arsenic and lead and the destruction of organic contaminants during the incineration process. The test program consisted of a series of bench-scale experiments with a muffle furnace and a series of incineration tests in a pilot-scale rotary kiln incinerator system. The study reported in this paper was funded by the Environmental Protection Agency under Contract 68–C9–0038 to Acurex Corporation. It has been subjected to the Agency's review and has been approved for publication. Mention of trade names or commercial products does not constitute endorsement or recommendation for use.     

Comparative evaluation of life cycle assessment models for solid waste management

This publication compares a selection of six different models developed in Europe and America by research organisations, industry associations and governmental institutions. The comparison of the models reveals the variations in the results and the differences in the conclusions of an LCA study done with these models. The models are compared by modelling a specific case - the waste management system of Dresden, Germany - with each model and an in-detail comparison of the life cycle inventory results. Moreover, a life cycle impact assessment shows if the LCA results of each model allows for comparable and consecutive conclusions, which do not contradict the conclusions derived from the other models' results. Furthermore, the influence of different level of detail in the life cycle inventory of the life cycle assessment is demonstrated. The model comparison revealed that the variations in the LCA results calculated by the models for the case show high variations and are not negligible. In some cases the high variations in results lead to contradictory conclusions concerning the environmental performance of the waste management processes. The static, linear modelling approach chosen by all models analysed is inappropriate for reflecting actual conditions. Moreover, it was found that although the models' approach to LCA is comparable on a general level, the level of detail implemented in the software tools is very different.