共查询到19条相似文献,搜索用时 110 毫秒
1.
引言矽钢片冲模在设计和制造上都应算作较为复杂的冲裁模。设计中首先要考虑模具的分类组合、冲头和托扳的固紧方式,退料装置的结构及模具上的革新——组合凹模等。根据生产实践,就以上四个问题浅谈笔者体会。 相似文献
2.
针对冷挤压组合凹模由于过盈装配后引起的凹模孔径变化,推导了计算凹模孔径变形量的计算公式,指出了从设计上保证组合凹模精确孔径的方法。 相似文献
3.
冷挤压组合凹模的失效主要是凹模内腔疲劳裂纹的出现,在模具设计的前期较为准确的估算出组合凹模的疲劳寿命是模具优化设计的前提。通过对组合凹模的应力分析后,采用Mises屈服准则的方法把凹模所受的多轴应力转化成单轴应力,再利用局部应力应变法找到了估算冷挤压组合凹模寿命的途径。 相似文献
4.
5.
6.
7.
应用厚壁圆筒的弹性解 ,分析了冷挤压三层组合凹模具有最大弹性极限时的优化设计 ,推导了三层组合凹模的最大承压、各层分界面半径和分界面过盈量的优化设计计算公式。利用所推导的计算公式 ,可实现三层组合凹模几何参数的最佳设计 相似文献
8.
9.
10.
11.
12.
论述了工艺分析在模具设计中的主导地位,着重指出冲压工艺方案的合理性是设计好模具的首要条件.并介绍了模具结构、工作原理及模具的使用情况. 相似文献
13.
本文在对各种气动性喷嘴及其雾化机理分析的基础上提出一种新型雾化喷嘴--旋切式气液两相喷嘴。该喷嘴具有结构简单、喷雾量无限可调、喷雾锥角调整灵活、防堵塞、雾化效果好的优点。通过CFD数值模拟研究发现,在旋切式喷嘴内部液流已经被气流剪切雾化成细小颗粒,其均匀的分散在气流中,在混合室内部形成气液混合流,形成一次雾化。当气液混合流脉冲喷出孔喷时,体积进一步膨胀,同时,高速液滴外部空气相互作用,产生二次雾化,促进了雾化效果。 相似文献
14.
Finite element analysis (FEA) has become an invaluable tool in the design of sheet metal stamping dies and processes. FEA has gained widespread acceptance as the best method of optimizing dies for conventional stamping processes. More recently, FEA has been shown to be an effective method of designing tooling for sheet forming processes. In this work, an FEA based approach is applied to the warm stamping (warm forming) process. This work introduces a new thermal finite element analysis software called PASSAGE®/Forming (PASSAGE) that enables the up-front design of the thermal management of warm forming dies. This thermal finite element analysis software is designed to specifically handle the forming and optimization scenarios related to the heating of a stamping die while minimizing user interface time. In this work, PASSAGE has been applied to a simple block of steel embedded with cartridge heaters to validate the prediction capability of this software under two different heating conditions. The results show that PASSAGE is capable of predicting the actual steady-state temperature distribution within the block with an acceptable level of accuracy while yielding notable information to the user with respect to specifying power requirements. A finite element software package like PASSAGE is a valuable tool that will aid greatly in the implementation of warm forming as a manufacturing process beyond the scope of the laboratory and into production. 相似文献
15.
此文介绍了非轴对称腰鼓形零件——水阀手柄闭式反向挤压模具的水平可分凹模结构设计及成刑试验工艺过程,为类似零件的锻压成形提供了成功的实例。 相似文献
16.
端头多半圆弯曲件比较常见,但质量难以保证。此文通过对成形弯曲工艺的分析,提出了改进措施,并介绍了两种典型模具结构,及其零部件的设计。 相似文献
17.
18.
给出了根据一种无内胎车轮轮辋滚形工艺各道滚形变形量确定方法而设计的模具 ,生产出的轮辋尺寸精度高、圆角减薄量小 ,且对各种型号的车轮通用性好 ,具有较大的现实意义。 相似文献