Biosorption of Cr(III) from aqueous solution by freeze-dried activated sludge: Equilibrium,kinetic and thermodynamic studies

Batch biosorption experiments were conducted to remove Cr(III) from aqueous solutions using activated sludge from a sewage treatment plant. An investigation was conducted on the effects of the initial pH, contact time, temperature, and initial Cr(III) concentration in the biosorption process. The results revealed that the activated sludge exhibited the highest Cr(III) uptake capacity (120 mg·g⁻¹) at 45°C, initial pH of 4, and initial Cr(III) concentration of 100 mg·L⁻¹. The biosorption results obtained at various temperatures showed that the biosorption pattern accurately followed the Langmuir model. The calculated thermodynamic parameters, ΔG^o (−0.8– −4.58 kJ·mol⁻¹), ΔH^o (15.6–44.4 kJ·mol⁻¹), and ΔS^o (0.06–0.15 kJ·mol⁻¹·K⁻¹) clearly indicated that the biosorption process was feasible, spontaneous, endothermic, and physical. The pseudo first-order and second-order kinetic models were adopted to describe the experimental data, which revealed that the Cr(III) biosorption process conformed to the second-order rate expression and the biosorption rate constants decreased with increasing Cr(III) concentration. The analysis of the values of biosorption activation energy (E_a = −7 kJ·mol⁻¹) and the intra-particle diffusion model demonstrated that Cr(III) biosorption was film-diffusion-controlled.     

A hybrid membrane process for simultaneous thickening and digestion of waste activated sludge

A hybrid membrane process for simultaneous sludge thickening and digestion (MSTD) was studied. During one cycle (15 d) of operation under a hydraulic retention time of 1 d, the concentration of mixed liquor suspended solids (MLSS) continuously increased from about 4 g·L⁻¹ to 34 g·L⁻¹, and the mixed liquor volatile suspended solids (MLVSS) increased from about 3 g·L⁻¹ to over 22 g·L⁻¹. About 42% of the MLVSS and 39% of the MLSS reduction were achieved. The thickening and digestion effects in the MSTD were further analyzed based on a mass balance analysis. Test results showed that biopolymers and cations of biomass were gradually released to the bulk solution during the process. It was also found that the capillary suction time, colloidal chemical oxygen demand, soluble microbial products, viscosity, and MLSS had significant positive correlations with the membrane fouling rate, whereas extracellular polymeric substances, polysaccharides, and proteins extracted from biomass had negative impacts on membrane fouling.     

Oxidation and biotoxicity assessment of microcystin-LR using different AOPs based on UV,O3 and H2O2

MC-LR removal performances under different AOPs were compared systematically. Higher removal efficiency and synergistic effects were obtained by combined process. The acute biotoxicity raised in different degrees after oxidation. Microcystin-LR attracts attention due to its high toxicity, high concentration and high frequency. The removal characteristics of UV/H₂O₂ and O₃/H₂O₂ advanced oxidation processes and their individual process for MC-LR were investigated and compared in this study. Both the removal efficiencies and rates of MC-LR as well as the biotoxicity of degradation products was analyzed. Results showed that the UV/H₂O₂ process and O₃/H₂O₂ were effective methods to remove MC-LR from water, and they two performed better than UV-, O₃-, H₂O₂-alone processes under the same conditions. The effects of UV intensity, H₂O₂ concentration and O₃ concentration on the removal performance were explored. The synergistic effects between UV and H₂O₂, O₃ and H₂O₂ were observed. UV dosage of 1800 mJ·cm⁻² was required to remove 90% of 100 mg·L⁻¹ MC-LR, which amount significantly decreased to 500 mJ·cm⁻² when 1.7 mg·L⁻¹ H₂O₂ was added. 0.25 mg·L⁻¹ O₃, or 0.125 mg·L⁻¹ O₃ with 1.7 mg·L⁻¹ H₂O₂ was needed to reach 90% removal efficiency. Furthermore, the biotoxicity results about these UV/H₂O₂, O₃/H₂O₂ and O₃-alone processes all present rising trends with oxidation degree of MC-LR. Biotoxicity of solution, equivalent to 0.01 mg·L⁻¹ Zn²⁺, raised to 0.05 mg·L⁻¹ Zn²⁺ after UV/H₂O₂ or O₃/H₂O₂ reaction. This phenomenon may be attributed to the aldehydes and ketones with small molecular weight generated during reaction. Advice about the selection of MC-LR removal methods in real cases was provided.     

Perfluorocarboxylic acids (PFCAs) and perfluoroalkyl sulfonates (PFASs) in surface and tap water around Lake Taihu in China

Perfluorinated compounds (PFCs) are ubiquitously distributed in the environment mainly as perfluoro-carboxylic acids (PFCAs) and perfluoroalkyl sulfonates (PFASs). In this paper, six PFCAs and two PFASs were quantified in surface and tap water samples from 12 sites around Lake Taihu near Shanghai City in East China. Predominant PFCs were perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), of which the concentration ranges were 6.8–206 and 1.2–45 ng·L⁻¹, the geometric means were 35.3 and 9.4 ng·L⁻¹, and the median (quartile range) values were 31.4 (34.4) and 10.4 (10.7) ng·L⁻¹, respectively. Other PFCs were also detected but in much lower concentrations than PFOA. The sources of the PFCs were expected to be direct industrial discharges in the Lake Taihu area, and this area was also a possible source of PFCs contaminations in Shanghai district in the downstream. PFCs distributions were found different in the upstream, downstream and north part of Lake Taihu. Occurrences of PFCs in the tap water in Lake Taihu area indicated their exposure to the local people. A brief estimation of the environmental risks by PFCs implied no acute or immediate risks from PFCs to local human health, but chronic risks from PFOA in the tap water should be considered in the downstream regions.     

Process control factors for continuous microbial perchlorate reduction in the presence of zero-valent iron

Process control parameters influencing microbial perchlorate reduction via a flow-through zero-valent iron （ZVI） column reactor were investigated in order to optimize perchlorate removal from water. Mixed perchlorate reducers were obtained from a wastewater treatment plant and inoculated into the reactor without further acclimation. Examined parameters included hydraulic residence time （HRT）, pH, nutrients requirement, and perchlorate reduction kinetics. The minimum HRT for the system was concluded to be 8 hr. The removal efficiency of 10 mg. L-1 influent perchlorate concentration was reduced by 20%-80% without control to the neutral pH （HRT = 8 hr）. Therefore pH was determined to be an important parameter for microbial perchlorate reduction. Furthermore, a viable alternative to pH buffer was discussed. The microbial perchlorate reduction followed the first order kinetics, with a rate constant （K） of 0.761 hr-1. The results from this study will contribute to the implementation of a safe, cost effective, and efficient system for perchlorate reduction to below regulated levels.     

Impact of solids on biphasic biodegradation of phenanthrene in the presence of hydroxypropyl- β -cyclodextrin (HPCD)

The consequence of polycyclic aromatic hydrocarbons (PAHs) in the environment is of great concern. The hydrophobic properties of PAHs significantly impact phase distribution causing limited bioavailability. Enhanced biodegradation has been extensively carried out by surfactants and the redeployment effect was recognized. However, the quantitative relationship concerning the impact of solids was rarely reported. A batch of biphasic tests were carried out by introducing Mycobacterium vanbaalenii PYR-1 and hydroxypropyl-β-cyclodextrin (HPCD) into a mixture of phenanthrene solution and various glass beads (GB37-63, GB105-125, and GB350-500). The comparative results demonstrated that HPCD had little effect on microbial growth and was not degradable by bacterium. A model was proposed to describe the biodegradation process. The regression results indicated that the partition coefficient k_d (1.234, 0.726 and 0.448 L·g⁻¹) and the degradation rate k (0 mmol·L⁻¹: 0.055, 0.094, and 0.112; 20 mmol·L⁻¹: 0.126, 0.141, and 0.156; 40 mmol·L⁻¹: 0.141, 0.156 and 0.184 d⁻¹) were positively and negatively correlated with the calculated total surface area (TSA) of solids, respectively. Degradation enhanced in the presence of HPCD, and the enhancing factor f was calculated (20 mmol·L⁻¹: 15.16, 40.01, and 145.5; 40 mmol·L⁻¹: 13.29, 37.97, and 138.4), indicating that the impact of solids was significant for the enhancement of biodegradation.     

Phenanthrene sorption to environmental black carbon in sediments from the Song-Liao watershed (China)

Black carbon (BC) in ten contaminated sediments from the Song-Liao watershed, NE China, was isolated upon treatments using a combustion method at 375°C, and the isolates’ sorption isotherms for phenanthrene (Phen) were determined. All sorption isotherms were nonlinear and fitted well by the Freundlich model. A negative relation was found between Freundlich sorption nonlinearity parameter (n values) and BC/total organic carbon (TOC) content of the original sediments (r²=0.687, p<0.01), indicating the dominance of BC in Phen sorption nonlinearity. The BC isolates from this industrialized region had n values of 0.342 to 0.505 and logK_FOC values of 6.02 to 6.42(μg·kg⁻¹·OC⁻¹)/(μg·L⁻¹) ⁿ for Phen. At a given C_e, the BC had higher K_oc value than the original sediments, revealing a higher sorption capacity for BC. BC was responsible for 50.0% to 87.3% of the total sorption at C_e=0.05 S_w, clearly indicating the dominance of BC particles in overall sorption of Phen by sediments.     

Ozonation of the 5-fluorouracil anticancer drug and its prodrug capecitabine: Reaction kinetics,oxidation mechanisms,and residual toxicity

Specific second-order rate constants were determined for 5-FU and CAP with ozone. Reaction sites were confirmed by kinetics, Fukui analysis, and products. The olefin moiety was the main ozone reaction site for 5-FU and CAP. Carboxylic acids comprised most of the residual TOC for 5-FU. Ozonation removed the toxicity associated with 5-FU and products but not CAP. Anticancer drugs (ADs) have been detected in the environment and represent a risk to aquatic organisms, necessitating AD removal in drinking water and wastewater treatment. In this study, ozonation of the most commonly used antimetabolite ADs, namely 5-fluorouracil (5-FU) and its prodrug capecitabine (CAP), was investigated to determine reaction kinetics, oxidation mechanisms, and residual toxicity. The specific second-order rate constants between aqueous ozone and 5-FU, 5-FU⁻, 5-FU²⁻, CAP, and CAP⁻ were determined to be 7.07(±0.11)×10⁴ M⁻¹·s⁻¹, 1.36(±0.06)×10⁶ M⁻¹·s⁻¹, 2.62(±0.17)×10⁷ M⁻¹·s⁻¹, 9.69(±0.08)×10³ M⁻¹·s⁻¹, and 4.28(±0.07)×10⁵ M⁻¹·s⁻¹, respectively; furthermore, the second-order rate constants for ^•OH reaction with 5-FU and CAP at pH 7 were determined to be 1.85(±0.20)×10⁹ M⁻¹·s⁻¹ and 9.95(±0.26)×10⁹ M⁻¹·s⁻¹, respectively. Density functional theory was used to predict the main ozone reaction sites of 5-FU (olefin) and CAP (olefin and deprotonated secondary amine), and these mechanisms were supported by the identified transformation products. Carboxylic acids constituted a majority of the residual organic matter for 5-FU ozonation; however, carboxylic acids and aldehydes were important components of the residual organic matter generated by CAP. Ozone removed the toxicity of 5-FU to Vibrio fischeri, but the residual toxicity of ozonated CAP solutions exhibited an initial increase before subsequent removal. Ultimately, these results suggest that ozone is a suitable technology for treatment of 5-FU and CAP, although the residual toxicity of transformation products must be carefully considered.     

Modified landfill gas generation rate model of first-order kinetics and two-stage reaction

This investigation was carried out to establish a new domestic landfill gas (LFG) generation rate model that takes into account the impact of leachate recirculation. The first-order kinetics and two-stage reaction (FKTSR) model of the LFG generation rate includes mechanisms of the nutrient balance for biochemical reaction in two main stages. In this study, the FKTSR model was modified by the introduction of the outflow function and the organic acid conversion coefficient in order to represent the in-situ condition of nutrient loss through leachate. Laboratory experiments were carried out to simulate the impact of leachate recirculation and verify the modified FKTSR model. The model calibration was then calculated by using the experimental data. The results suggested that the new model was in line with the experimental data. The main parameters of the modified FKTSR model, including the LFG production potential (L₀), the reaction rate constant in the first stage (K₁), and the reaction rate constant in the second stage (K₂) of 64.746 L, 0.202 d⁻¹, and 0.338 d⁻¹, respectively, were comparable to the old ones of 42.069 L, 0.231 d⁻¹, and 0.231 d⁻¹. The new model is better able to explain the mechanisms involved in LFG generation.     

Sorption and desorption of pymetrozine on six Chinese soils

Pymetrozine is a selective insecticide with a unique chemical structure and mode to control hemipteran and homopteran. While pymetrozine has brought great benefits to crop production by killing insects, its residues in soil may have a detrimental effect on environment. Therefore, it is of great importance to investigate its behaviors in soil. In this study, the sorption and desorption of pymetrozine on six Chinese soils were investigated using a batch equilibrium approach to understand its mobile behavior in the soils. Both sorption and desorption isotherms of pymetrozine were in good agreement with the Freundlich model. The sorption coefficient K_F varied between 3.37 and 58.32 mL∙g⁻¹ and the sorption isotherms were nonlinear, with 1/n ranging from 0.57 to 0.91. A regression equation was proposed to predict the sorption of pymetrozine on six different soil samples: log K_F = 4.3708 − 4.5709 × log (pH in 0.01mol·L⁻¹ CaCl₂) + 0.4700 × log OC% + 0.0057 × sand (%) + 0.0022 × CEC(clay), with R² = 0.9982. The organic carbon content of soil positively affected the sorption of pymetrozine, but soil pH had a negative effect on the sorption. Additionally, effects of CaCl₂ concentration, soil to solution ratio and pesticide form were investigated. The sorption was promoted with an increase in soil to solution ratio and a decrease in CaCl₂ concentration. The possible variation of the five formulated products of pymetrozine was also investigated.     

Occurrence of veterinary antibiotics in struvite recovery from swine wastewater by using a fluidized bed

Antibiotics in wastewater pose pharmacological threats to phosphorous recovery. Recovered struvite particles possessed significantly antibiotic residues. Smaller granules contained much more antibiotics than the larger ones. Organic matters and struvite granulation process exerted significant impacts. Recovering phosphorus from livestock wastewater has gained extensive attention. The residue of veterinary antibiotics in the wastewater may be present in the recovered products, thereby posing pharmacological threats to the agricultural planting and human health. This study investigated antibiotic occurrence in the struvite particles recovered from swine wastewater by using a fluidized bed. Results revealed that tetracyclines possessed significant residues in the struvite granules, with the values ranging from 195.2 mg·kg⁻¹ to 1995.0 mg·kg⁻¹. As for fluoroquinolones, their concentrations varied from 0.4 mg·kg⁻¹ to 1104.0 mg·kg⁻¹. Struvite particles were of various sizes and shapes and displayed different antibiotic adsorption capacities. The data also showed that the smaller granules contained much more antibiotics than the larger ones, indicating that the fluidized granulation process of struvite crystals plays an important role on the accumulation of antibiotics. For tetracyclines, organic matters and struvite adsorption exerted significant impacts on tetracyclines migration. The outcomes underscore the need to consider the residues of antibiotics in resource recovery from wastewater because they exert pharmacological impacts on the utilization of recovered products.     

Engineering application of membrane bioreactor for wastewater treatment in China: Current state and future prospect

China has been the forerunner of large-scale membrane bioreactor （MBR） application. Since the first large-scale MBR （≥ 10 000 m^3·d^-1） was put into operation in 2006, the engineering implementation of MBR in China has attained tremendous development. This paper outlines the commercial application of MBR since 2006 and provides a variety of engineering statistical data, covering the fields of municipal wastewater, industrial wastewater, and polluted surface water treatment. The total treatment capacity of MBRs reached 1× 10^6 m^3·d^-1 in 2010, and has currently exceeded 4.5 × 10^6 m^3·d^-1 with -75% of which pertaining to municipal wastewater treatment. The anaerobic/anoxic/aerobie-MBR and its derivative processes have been the most popular in the large-scale municipal application, with the process features and typical ranges of parameters also presented in this paper. For the treatment of various types of industrial wastewater, the configurations of the MBR-based processes are delineated with representative engineering cases. In view of the significance of the cost issue, statistics of capital and operating costs are also provided, including cost structure and energy composition. With continuous stimulation from the environmental stress, political propulsion, and market demand in China, the total treatment capacity is expected to reach 7.5 × 10^6 m^3·d^-1 by 2015 and a further expansion of the market is foreseeable in the next five years. However, MBR application is facing several challenges, such as the relatively high energy consumption. Judging MBR features and seeking suitable application areas should be of importance for the long-term development of this technology.     

Removal of clofibric acid from aqueous solution by polyethylenimine-modified chitosan beads

Polyethylenimine （PEI）-modified chitosan was prepared and used to remove clofibric acid （CA） from aqueous solution. PEI was chemically grafted on the porous chitosan through a crosslinking reaction, and the effects of PEI concentration and reaction time in the preparation on the adsorption of clofibric acid were optimized. Scanning electron microscopy （SEM） showed that PEI macromolecules were uniformly grafted on the porous chitosan, and the analysis of pore size distribution indicated that more mesopores were formed due to the crosslinking of PEI molecules in the macropores of chitosan. The PEI-modified chitosan had fast adsorption for CA within the initial 5 h, while this adsorbent exhibited an adsorption capacity of 349 mg· g^-1 for CA at pH 5.0 according to the Langmuir fitting, higher than 213 mg· g^-1 on the porous chitosan. The CA adsorption on the PEI- modified chitosan was pH-dependent, and the maximum adsorption was achieved at pH 4.0. Based on the surface charge analysis and comparison of different pharmaceu- ticals adsorption, electrostatic interaction dominated the sorption of CA on the PEI-modified chitosan. The PEI- modified chitosan has a potential application for the removal of some anionic rnicropollutants from water or wastewater.     

Preparation of nZVI embedded modified mesoporous carbon for catalytic persulfate to degradation of reactive black 5

• The MCNZVI is prepared as an interesting material for PS activation. • Graphitized carbon shells facilitate electron transfer from Fe⁰. • The MCNZVI exhibits excellent performance to degrade RB5 by ¹O₂. • The MCNZVI has high stability and reusability in the oxidation system. High-efficiency and cost-effective catalysts with available strategies for persulfate (PS) activation are critical for the complete mineralization of organic contaminants in the environmental remediation and protection fields. A nanoscale zero-valent iron-embedded modified mesoporous carbon (MCNZVI) with a core-shell structure is synthesized using the hydrothermal synthesis method and high-temperature pyrolysis. The results showed that nZVI could be impregnated within mesoporous carbon frameworks with a comparatively high graphitization degree, rich nitrogen doping content, and a large surface area and pore volume. This material was used as a persulfate activator for the oxidation removal of Reactive Black 5 (RB5). The effects of the material dosage, PS concentration, pH, and some inorganic anions (i.e., Cl⁻, SO₄²⁻) on RB5 degradation were then investigated. The highest degradation efficiency (97.3%) of RB5 was achieved via PS (20 mmol/L) activation by the MCNZVI (0.5 g/L). The pseudo-first-order kinetics (k = 2.11 × 10⁻² min⁻¹) in the MCNZVI/PS (0.5 g/L, 20 mmol/L) was greater than 100 times than that in the MCNZVI and PS. The reactive oxygen species (ROS), including ¹O₂, SO₄^·−, HO^·, and ·O₂⁻, were generated by PS activation with the MCNZVI. Singlet oxygen was demonstrated to be the primary ROS responsible for the RB5 degradation. The MCNZVI could be reused and regenerated for recycling. This work provides new insights into PS activation to remove organic contamination.     

Determination and occurrence of endocrine disrupting compounds,pharmaceuticals and personal care products in fish (Morone saxatilis)

Endocrine disrupting compounds (EDCs), pharmaceuticals and personal care products (PPCPs) have attracted much attention due to widespread contamination in aquatic environment. In this study, we determined 13 EDCs and PPCPs in fish blood, bile and muscle by using gas chromatography-mass spectrometry (GC-MS). The limits of quantitation (LOQ) were in the ranges of 0.23–2.54, 0.22–2.36 ng·mL⁻¹, and 0.24–2.57 ng·g⁻¹ dry weight (dw) for fish blood, bile and muscle, respectively. Recoveries of target compounds spiked into sample matrices and passed through the entire analytical procedure ranged from 65% to 95%, from 60% to 92% and from 62% to 91% for blood, bile and muscle, respectively. The methods were applied to the analysis of fish from a lake in California. Target compounds were relatively low in bile, and only bisphenol A (BPA) and diclofenac were measurable near the LOQ. Seven of 13 compounds were detected in blood, with total concentrations up to 39 ng·mL⁻¹. Only BPA was frequently found in muscle, with mean concentration of 7.26 ng·g⁻¹ dw. The estimated daily intake of BPA through fish consumption for U.S. resident was significantly lower than the tolerable daily intake recommended by the European Food Safety Authority. This study showed that the exposure to the bisphenol A from fish diet is unlikely to pose a health risk.     

Fe2O3-CeO2-Bi2O3/γ-Al2O3 catalyst in the catalytic wet air oxidation (CWAO) of cationic red GTL under mild reaction conditions

Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃, an environmental friendly material, was investigated. The catalyst exhibited good catalytic performance in the CWAO of cationic red GTL. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. HO₂· and O₂·⁻ appeared as the main reactive species in the reaction. The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst, a novel environmental-friendly material, was used to investigate the catalytic wet air oxidation (CWAO) of cationic red GTL under mild operating conditions in a batch reactor. The catalyst was prepared by wet impregnation, and characterized by special surface area (BET measurement), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst exhibited good catalytic activity and stability in the CWAO under atmosphere pressure. The effect of the reaction conditions (catalyst loading, degradation temperature, solution concentration and initial solution pH value) was studied. The result showed that the decolorization efficiency of cationic red GTL was improved with increasing the initial solution pH value and the degradation temperature. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. Hydroperoxy radicals (HO₂·) and superoxide radicals (O₂⁻·) appeared as the main reactive species upon the CWAO of cationic red GTL.     

PVDF ultrafiltration membranes of controlled performance via blending PVDF-g-PEGMA copolymer synthesized under different reaction times

PVDF blended different graft ratio of PVDF-g-PEGMA were systematically studied. Tuning the amphiphilic copolymer synthesis time to control membrane performance. The PVDF membrane with PVDF-g-PEGMA at 19 h possesses most surface oxygen content. The synthesis time of PVDF-g-PEGMA at 9 h is good for high flux UF membrane. Polyvinylidene fluoride grafted with poly(ethylene glycol) methyl ether methacrylate (PVDF-g-PEGMA) was synthesized using atomic transfer radical polymerization (ATRP) at different reaction times (9 h, 19 h, and 29 h). The corresponding conversion rates were 10%, 20% and 30%, respectively. PVDF was blended with the copolymer mixture containing PVDF-g-PEGMA, solvent and residual PEGMA under different reaction times. In this study, we explored the effect of the copolymer mixture additives with different synthesis times on cast membrane performance. Increasing the reaction time of PVDF-g-PEGMA causes more PVDF-g-PEGMA and less residual PEGMA to be found in the casting solution. Incremental PVDF-g-PEGMA can dramatically increase the viscosity of the casting solution. An overly high viscosity led to a delayed phase inversion, thus hindering PEGMA segments in PVDF-g-PEGMA from migrating to the membrane surface. However, more residual PEGMA contributed to helping more PEGMA segments migrate to the membrane surface. The pure water fluxes of the blended membrane with reaction times of 9 h, 19 h, and 29 h are 5445 L·m⁻²·h⁻¹, 1068 L·m⁻²·h⁻¹and 1179 L·m⁻²·h⁻¹, respectively, at 0.07 MPa. Delayed phase inversion can form smaller surface pore size distributions, thus decreasing the water flux for the membranes with PVDF-g-PEGMA at 19 h and 29 h. Therefore, we can control the membrane pore size distribution by decreasing the reaction time of PVDF-g-PEGMA to obtain a better flux performance. The membrane with PVDF-g-PEGMA at 19 h exhibits the best foulant rejection and cleaning recovery due to its narrow pore size distribution and high surface oxygen content.     

Elimination of antibiotic resistance genes and control of horizontal transfer risk by UV-based treatment of drinking water: A mini review

Antibiotic-resistant bacteria and antibiotic resistance genes are in water bodies. UV/chlorination method is better to remove ARGs than UV or chlorination alone. Research on UV/hydrogen peroxide to eliminate ARGs is forthcoming. UV-based photocatalytic processes are effective to degrade ARGs. Antibiotic-resistant bacteria (ARB) and antibiotic resistance genes (ARGs) have been recognized as one of the biggest public health issues of the 21st century. Both ARB and ARGs have been determined in water after treatment with conventional disinfectants. Ultraviolet (UV) technology has been seen growth in application to disinfect the water. However, UV method alone is not adequate to degrade ARGs in water. Researchers are investigating the combination of UV with other oxidants (chlorine, hydrogen peroxide (H₂O₂), peroxymonosulfate (PMS), and photocatalysts) to harness the high reactivity of produced reactive species (Clž·, ClOž·ž, Clž₂·ž⁻, žž·OH, and SOž₄ž·⁻€) in such processes with constituents of cell (e.g., deoxyribonucleic acid (DNA) and its components) in order to increase the degradation efficiency of ARGs. This paper briefly reviews the current status of different UV-based treatments (UV/chlorination, UV/H₂O₂, UV/PMS, and UV-photocatalysis) to degrade ARGs and to control horizontal gene transfer (HGT) in water. The review also provides discussion on the mechanism of degradation of ARGs and application of q-PCR and gel electrophoresis to obtain insights of the fate of ARGs during UV-based treatment processes.     

Contributions of adsorption,bioreduction and desorption to uranium immobilization by extracellular polymeric substances

● EPS immobilizes U(VI) via adsorption, bioreduction and desorption. ● This work provides a framework to quantify the three immobilization processes. ● The non-equilibrium adsorption of U follows pseudo-second-order kinetics. ● The equilibrium adsorption of U followed Langmuir and Freundlich isotherms. Hexavalent uranium (U(VI)) can be immobilized by various microbes. The role of extracellular polymeric substances (EPS) in U(VI) immobilization has not been quantified. This work provides a model framework to quantify the contributions of three processes involved in EPS-mediated U(VI) immobilization: adsorption, bioreduction and desorption. Loosely associated EPS was extracted from a pure bacterial strain, Klebsiella sp. J1, and then exposed to H₂ and O₂ (no bioreduction control) to immobilize U(VI) in batch experiments. U(VI) immobilization was faster when exposed to H₂ than O₂ and stabilized at 94% for H₂ and 85% for O₂, respectively. The non-equilibrium data from the H₂ experiments were best simulated by a kinetic model consisting of pseudo-second-order adsorption (k_a = 2.87 × 10⁻³ g EPS·(mg U)⁻¹·min⁻¹), first-order bioreduction (k_b = 0.112 min⁻¹) and first-order desorption (k_d = 7.00 × 10⁻³ min⁻¹) and fitted the experimental data with R² of 0.999. While adsorption was dominant in the first minute of the experiments with H₂, bioreduction was dominant from the second minute to the 50^th min. After 50 min, adsorption was negligible, and bioreduction was balanced by desorption. This work also provides the first set of equilibrium data for U(VI) adsorption by EPS alone. The equilibrium experiments with O₂ were well simulated by both the Langmuir isotherm and the Freundlich isotherm, suggesting multiple mechanisms involved in the interactions between U(VI) and EPS. The thermodynamic study indicated that the adsorption of U(VI) onto EPS was endothermic, spontaneous and favorable at higher temperatures.     

Occurrence and behavior of pharmaceuticals in sewage treatment plants in eastern China

The occurrence and removal efficiency of seven pharmaceuticals (norfloxacin, trimethoprim, roxithromycin, sulfamethoxazole, ibuprofen, diclofenac and carbamazepine) were determined in three sewage treatment plants (STPs) with anaerobic/anoxic/oxic, anoxic/oxic and oxidation ditches processes in Xuzhou City, Eastern China. The results showed that seven pharmaceuticals were detected in the influent samples with concentrations ranging from 93 to 2540 ng·L⁻¹. The removal of these substances among the three different STPs varied from 36 to 84%, with the highest performance obtained by the wastewater treatment works with tertiary treatment (sand filtration). Most of the compounds were removed effectively during biologic treatment while sand filtration treatment also made a contribution to the total elimination of most pharmaceuticals. The efficiency comparison of the three sewage treatment processes showed that the STP which employed anaerobic/anoxic/oxic was more effective to remove pharmaceuticals than the oxidation ditches and anoxic/oxic.