Optimization of the ionization conditions for the trace analysis of PCDD/PCDF with ion trap MS/MS

Commercial ion trap mass spectrometer provides easy-to-operate MS/MS analysis for the determination of PCDD/PCDF. The limit of quantification is appropriately low (0.2 pg for 23478-P5CDF) because all the stages are performed in the trap and sample losses associated with the ion transportation are minimized. However, if excessive ions are injected into the trap, its electrical fields are distorted and an overall reduction in performance arises. Ionization condition is an important parameter as it affects the amount of the total ions produced. If the amount of interfering compounds are negligible, such as standard solution or cleaned-up sample, lower ionization condition (e.g. electron energy: 30 eV, emission current (EC): 150 μA) is preferable. On the contrary, in case excessive interfering ions are coexisting with PCDD/PCDF, such as crude extract or semi-cleaned-up sample, the ionization condition should be high (e.g. electron energy: 90 eV, EC: 350 μA) for the reproductive quantification.     

Application of GC-MS/MS for the analysis of PCDD/Fs in sewage effluents

The application of high resolution gas chromatography in combination with tandem mass spectrometry in an ion trap was tested to substitute the expensive high resolution mass spectrometry in analysing polychlorinated dibenzo-p-dioxins and furans in sewage effluents. In tandem mass spectrometry, a set of parameters has to be optimised in order to attain the required sensitivity. To the best of our knowledge, this is the first time a method development for analysing PCDD/Fs with GC-MS/MS in an ion trap is described in this detail. Nine parameters are varied, including isolation window, collision induced dissociation (CID) amplitude, CID time, acquisition mass range, broadband amplitude, CID bandwidth, modulation range, filament current and ion trap temperature. This technique can be adapted to other analytes. By this optimisation, limits of detection of 0.01-0.05 ng/l are obtained. With its selectivity and sensitivity, tandem mass spectrometry is a powerful tool for the determination of PCDD/Fs in water samples. 55 sewage effluent samples from Germany were analysed.     

Analysis of dioxins and furans in environmental samples by GC-ion-trap MS/MS

The work aims to characterise PCDDs/Fs in environmental matrices by high resolution gas chromatography coupled to low resolution quadrupole ion-trap mass spectrometry (GC-QITMS/MS). In particular, the study was mainly focused in different environmental samples such as sewage sludge, soils, and sediments and in combustion residues as fly ashes. Previous experiences have already detected and quantified PCDDs/PCDFs in all matrices studied. Moreover, isomer-specific analysis of 2,3,7,8-PCDDs/Fs compounds corroborated good correlation between GC-QITMS/MS and a well-established technique such as high resolution mass spectrometry (HRMS). Finally, QC measures included the participation in intercalibration exercises. Successful results were achieved using GC-QITMS/MS in the analysis of fly ashes, soils and sediment materials. In general, GC-QITMS/MS constitutes an interesting alternative for routine analysis of dioxins in such as matrices.     

Determination of acidic herbicides in cereals by QuEChERS extraction and LC/MS/MS

A simple and rapid method has been studied for the determination of acidic herbicides (2,4-D, Dichlorprop, Dichlorprop-p, Fluazifop, Fluroxypyr, MCPA, Mecoprop and Mecoprop-p) on cereals (rye). The method involves an alkaline hydrolysis with sodium hydroxide in order to release covalently bound compounds, prior to QuEChERS extraction, followed by neutralization and analysis via liquid chromatography-double mass spectrometry LC/MS/MS. The performance of the method either with or without alkaline hydrolysis was studied in terms of recovery rates and limit of quantification (LOQ). In either case, recoveries were determined at four spiking levels (0.02 mg/kg, 0.05 mg/kg, 0.1 mg/kg and 0.5 mg/kg) with 5 replicates for each level. Mean recoveries ranged from 90 to 120 %, whereas relative standard deviations (RSD %) proved to be less than 20 %. Quantitative analysis was carried out by the internal standard (Nicarbazin) and the LC/MS/MS analysis was performed in electrospray ionisation (ESI) negative mode using a Zorbax XCB Eclipse column. The developed method was applied to the analysis of several cereals commercially available like as rye flour, oat meal, oat flakes and dehusked oat. Residue levels were found below the limit of quantification (LOQ) of the method. The method has been tested in EU Proficiency Tests for cereals with good results.     

Development of an SPME-GC-MS/MS method for the determination of pesticides in rainwater: laboratory and field experiments

A solid-phase microextraction -- coupled to a gas chromatography -- ion trap tandem mass spectrometry (SPME-GC-MS/MS) method was developed for the quantitative determination in rainwater of 8 pesticides amongst the most used in France and 3 triazines metabolites. The main factors affecting the SPME process were studied. Using a 3 mL sample, the method developed showed good linearity for concentrations ranging from 0.05 to 50 microgL(-1) with correlation coefficients between 0.997 and 0.9999 and relative standard deviations (% RSD) below 14%. The study of matrix effects showed that rainwater was too diluted to have any significant influence on the extraction efficiency. To validate the method, a field campaign was carried out on the rain events, which occurred in Strasbourg during a one-year period. The rain concentrations showed patterns of high pesticide concentrations during spring months, which were correlated to the spraying periods of most of these substances.     

Dechlorination/hydrogenation and destruction reactions of PCDDs in OCDD-added fly ash heated under vacuum

Octachlorodibenzo-p-dioxin (OCDD)-added, pretreated fly ash was heated under vacuum at sample temperatures ranging from T(s)=450 to 650 K. The fly ash and liquid nitrogen-cooled trap samples were analyzed for DD/DF through OCDD/DF. The total amounts of DD through OCDD decrease with increasing T(s), which indicates that dechlorination/hydrogenation (DCH) reactions are not the only reaction channels. Reduction of toxic equivalent (TEQ) for PCDDs by more than 99% was achieved in the fly ash by the vacuum heat treatment at T(s)=650 K for 4 h. The total amount of PCDDs and DD detected in the liquid nitrogen-cooled trap relative to that of added OCDD was about 17%, i.e., PCDDs and DD which were adsorbed to the fly ash surfaces can evaporate into the gaseous phase. The difference between the evaporation behavior of PCDDs in the present and the previous studies is discussed in the light of their states of existence.     

Optimisation and use of tandem-in-time mass spectrometry in comparison with immunoassay and HRGC/HRMS for PCDD/F screening

Rapid screening of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans using quadrupole ion storage tandem-in-time mass spectrometry (QISTMS) conjointly with polyclonal antibody immunoassay has been considered. The optimisation of the fragmentation of the parent ion in the trap has been completed. The analysis of fly ashes from a municipal waste incinerator contaminated at different levels has then been realised. Results obtained using QISTMS, HRMS and immunoassay are compared.     

Removal of PCDDs/DFs and dl-PCBs in MWI fly ash by heating under vacuum

Temperature dependence of PCDD/DF and dioxin-like polychlorinated biphenyl (dl-PCB) concentrations in fly ash from a municipal waste incinerator (MWI) heated under vacuum has been investigated as a function of sample temperature ranging from T(s)=425 to 800 K to find out if PCDDs/DFs in fly ash evaporate and are trapped in a liquid nitrogen-cooled trap. The results show that more than 99.98% of PCDDs/DFs in TEQ is removed from fly ash by vacuum heat treatment at T(s)>650 K for 4 h. Almost no PCDDs/DFs were detected in the liquid nitrogen-cooled trap. Homologue distributions indicate that dechlorination/hydrogenation (DCH) reactions proceed in fly ash at T(s)>450 K. Arrhenius rate parameters for the DCH reactions have been determined for each homologue assuming that only DCH reactions occur. The fly ash heated under vacuum at 650 or 800 K was reheated at 573 K (300 degrees C) in a stream of dry or humid air to see how much PCDDs/DFs and dl-PCBs are regenerated. We have found that (1) PCDDs/DFs are regenerated in both 650 K and 800 K treated fly ash, whereas dl-PCBs are regenerated in 650 K treated fly ash, (2) formation of PCDFs predominates over that of PCDDs or dl-PCBs, and (3) less chlorinated homologues are abundant for PCDDs/DFs and dl-PCBs.     

Evaluation and validation of two different chromatographic methods (HPLC and LC-MS/MS) for the determination and confirmation of ochratoxin A in pig tissues

This study was undertaken to compare two different analytical methods for the determination and confirmation of ochratoxin A (OTA) in blood serum, kidney and liver of pigs. Sample clean-up was based on liquid-liquid phase extraction. The detection of OTA was accomplished with high-performance liquid chromatography (HPLC) combined either with fluorescence detection (FL) or electro spray ionization (ESI+) tandem mass spectrometry (MS–MS). Comparative method evaluation was based on the investigation of 90 samples of blood serum, kidney and liver per animal originating from different regions of Serbia. The analytical results are discussed in view of the respective method validation data and the corresponding experimental protocols. In general, analytical data obtained with (LC–MS–MS) liquid chromatography electro spray tandem mass spectro metry detection offered comparable good results at the sub-ppb concentration level. The results indicate that the liquid chromatography electro spray tandem mass spectrometric (LC-MS/MS) method was more specific and sensitive for the analysis and confirmation of ochratoxin A in pig tissues then high pressure liquid chromatography (HPLC) method after methylation of OTA.     

Analysis of volatile organic compounds, using the purge and trap injector coupled to a gas chromatograph/ion-trap mass spectrometer: review of the results in Dutch surface water of the Rhine, Meuse, Northern Delta Area and Westerscheldt, over the period 1992-1997

Volatile organic compounds are widely introduced into the Dutch aquatic environment. Liquid-liquid extraction and isolation by means of resins give poor recoveries for volatiles. In this study, a method has been developed to analyse these compounds with a purge and trap injection (PTI) coupled to a chromatograph/ion trap mass spectrometer. Volatile compounds are "purged" from the sample by carrier gas flow and transported through a condenser to a cooled trap. The bulk of liquid matrix is condensed in the condenser, while volatile compounds are left unaffected. The compounds of interest are trapped at a low temperature, by liquid nitrogen in the cooled trap of fused silica. Injection takes place by flash heating of the trap. The detection limits of the volatile compounds are in the range of 0.001-0.04 microgram l-1, in full spectrum mode. In this paper a review of the results in Dutch surface water of the Rhine, Meuse, Northern Delta Area and Westerscheldt, over the period 1992-1997, is presented. For calamities causing high levels of volatiles, the method is very useful. The compounds can be monitored over a certain period. In the Meuse, high levels of volatile organic compounds are observed. Diisopropyl ether at a maximum of 592 micrograms l-1.     

Isomeric analysis of PCDD/PCDF in waste incinerator fly ash by GC-MS/MS

The development of an analytical method for the analysis of PCDD/PCDF in flyash using a bench analytical system comprising of a gas chromatograph fitted with an ion trap detector operated in the tandem MS mode is described. The optimum settings for the most important MS/MS parameters are given, including those for the less reported mono- to tri-chlorinated dioxin and furan congener groups. Flyash samples from three waste incineration plants representing a decommissioned 1970s plant design, an upgraded and still operating plant originally designed in the 1970s, and a modern 1990s design operating plant have been analysed for PCDD/PCDF. The flyash samples were analysed for PCDD/PCDF using the methods developed and the total PCDD/PCDF, I-TEQ values and isomeric profiles are reported. The flyash from the older decommissioned incinerator had very significantly higher concentrations of PCDD/PCDF compared to the modern incinerator flyash.     

Characterization of individual fly ash particles emitted from coal- and oil-fired power plants

Individual particles from coal- and oil-fired power plants were analyzed by scanning electron microscope equipped with an energy dispersive X-ray spectrometer to investigate size, morphology, and composition. Samples were collected on filters by dichotomous sampler in the fine ( <2.5 μm aerodynamic diameter) and coarse (2.5 to 5–10 μm) fractions. In both fractions coal fly ash particles were predominantly ( > 95%) smooth, mineral spheres. No cenospheres (perforated hollow spheres) were detected, and almost 90% of the mass concentrations occurred in the coarse fraction. Sulfur as lared as a surface layer on the mineral core; the abundances of Fe and S were highly variable. The Al/Si ratio was fairly constant for most of the spheres but not for the relatively few Fe-rich or non-spherical coal fly ash particles. Over 90% of the mass of oil fly ash occurred in the fine fraction. The size distribution of chemical and morphological properties of individual oil fly ash particles was found to be trimodal. Oil fly ash particles smaller than 0.7 μ (geometric diameter) were non-spherical and relatively pure in sulfate, and 90% of such particles were smaller than 0.5 μm; V or Ni could be detected in 50% to 60% of such particles larger than 0.3 μm. Those particles in the 0.7–3 μm range of geometric diameters were predominantly spherical and of mineral composition, highly variable in Al, Si, P, Ca, Ti and Fe; 50–60% of them contained detectable amounts of V or Ni. Larger oil fly ash particles had a lacy morphology and consisted of carbonaceous material and sulfur.     

A comparative study on the recovery of polycyclic aromatic hydrocarbons from fly ash and lignite coal

The recovery of polycyclic aromatic hydrocarbons (PAHs) from lignite coal burnt in Greek power stations and the fly ash produced is examined comparatively using Soxhlet, ultrasonic and accelerated solvent extraction procedures with various organic solvents. Soxhlet using toluene/methanol mixture and accelerated solvent extraction/toluene were found to be the most efficient methods for fly ash PAHs, yielding average recoveries of about 80%. The accelerated solvent extraction/toluene procedure was superior for lignite PAHs, yielding 96% average recovery, whereas ultrasonic and Soxhlet extraction yielded relatively lower recoveries (75% and 67%, respectively).     

Gas chromatography/mass spectrometry applied for the analysis of triazine herbicides in environmental waters

The excess use of triazine herbicides in agriculture causes severe contamination to the environment especially for ground water. Gas chromatography coupled with mass spectrometry (GC/MS) was used to analyze simazine, atrazine (ATR), cyanazine, as well as the degradation products of ATR such as deethylatrazine and deisopropylatrazine in environmental water samples. These compounds were baseline separated by the established GC method. The water samples were pre-concentrated by solid-phase-extraction (SPE) and analyzed by ion trap MS at sub- to low-ppt levels. Recovery of ATR by the SPE pre-concentration using a C18 cartridge was determined as 90.5 +/- 3.5%. Detection limit of the method using selected ion monitoring technique for ATR was 1.7 ppt when one liter water was analyzed. The relative analytical error for ATR fortified water samples at 200 ppt was -12.5% (n=12) with triple analysis and the relative standard deviation was 3.2%. Trace levels of ATR at 3.9 and 9.7 ppt were determined in water samples collected from a reservoir and a river in Hong Kong.     

Formation of polychlorinated dibenzo-p-dioxins/dibenzofurans from residual carbon on municipal solid waste incinerator fly ash using Na37Cl

Na37Cl was used to study the role of chlorine in the formation of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) from carbon. Adding Na37Cl to fly ash showed that this compound was a (relatively) poor chloride source; chlorine naturally present on the ash - which could include both chlorine in residual carbon and (metal) chlorides - was found to be ca. 17x more reactive. When both Na37Cl and CuCl2 were added to aqueous extracted fly ash, the percentage of 37Cl from Na37Cl included in PCDD/F increased, compared to the combination of Na37Cl/fly ash. When Na37Cl and CuCl2 were exchanged in water, followed by evaporation of the solvent, and mixed with aqueous extracted fly ash, the percentage of 37Cl included in PCDD/F was much higher. Apparently, direct transfer of 37Cl from CuCl2 to carbon and PCDD/F was much faster than transfer of 37Cl- from Na37Cl via a metal chloride (such as CuCl2) to carbon and PCDD/F. In addition to chlorine in PCDD/F originating from exchanged NaCl/CuCl2, chloride left on the fly ash after aqueous extraction and chlorine present in residual carbon could also have been incorporated in PCDD/F.     

LC-MS/MS method validation for determination of selected neonicotinoids in groundwater for the purpose of a column experiment

The work was carried out to develop and validate a method based on liquid chromatography tandem mass spectrometry (LC-MS/MS) for the simultaneous detection and quantification of five neonicotinoid insecticides: acetamiprid, clothianidin, imidacloprid, thiacloprid and thiamethoxam in groundwater samples for the purpose of a further column experiment. This experiment will be used to analyze breakthrough curves of neonicotinoids under a saturated water flow to set transport parameters, where the reliability of the results of chemical analysis plays an important role. The validation was performed in a concentration range from 0.09?µg L^?1 to 100?µg L^?1 using an Infinity 1290 (Agilent, USA) chromatograph coupled with a QTrap 5500 mass spectrometer (Sciex, Canada). The calibration curves were obtained on the basis of the results of six standard solution analyses. Linearity was not lower than 0.998. The limit of detection was set at the lowest concentration which can be determined with an acceptable accuracy and precision. All pesticides had recoveries in the range 85–109% with relative standard deviation values less than 8.1%. The estimated measurement uncertainty did not exceed 30%, so the LC-MS/MS method fits for the intended purpose.     

Analytical improvements of hybrid LC-MS/MS techniques for the efficient evaluation of emerging contaminants in river waters: a case study of the Henares River (Madrid, Spain)

Purpose  

Instrumental capabilities and software tools of modern hybrid mass spectrometry (MS) instruments such as high-resolution mass spectrometry (HRMS), quadrupole time-of-flight (QTOF), and quadrupole linear ion trap (QLIT) were experimentally investigated for the study of emerging contaminants in Henares River water samples.     

Application of a purge and trap TDS-GC/MS procedure for the determination of emissions from flame retarded polymers

Emissions of volatile organic compounds (VOCs) from different thermoplastic polymers used in electrotechnical applications were investigated using a purge and trap procedure that involved adsorption on Tenax GR. Results were compared to those for an operating TV set monitored in a test chamber. The analyses were in both cases carried out using thermodesorption gas chromatography with mass spectrometric detection (TDS-GC/MS). Substances identified were monomers, volatile additives, or related compounds. Special attention was given to the detection of halogenated compounds. Their origin was studied using reference samples and synthetic standards.     

壳聚糖联合碱改性粉煤灰对重金属离子的吸附特性

采用浸渍法将壳聚糖负载在经NaOH改性的粉煤灰上,制备了联合改性的粉煤灰。随粉煤灰上壳聚糖负载量的增加,粉煤灰对Pb²⁺和Cd²⁺的吸附率均提高。当负载壳聚糖的质量分数为8%,吸附温度为30℃,吸附时间为120 min时,粉煤灰对Pb²⁺的吸附率最高（为98.9%）,对Cd²⁺的吸附率也最高（为91.5%）。其吸附行为符合Freundlich等温吸附模型,但表现为2个线性区。粉煤灰负载壳聚糖的改性机理是粉煤灰与带正电荷的壳聚糖的化学键合作用。     

Aerosol laser ablation mass spectrometry of suspended powders from PM sources and its implications to receptor modeling

Primary sources of particulate matter (PM) were analyzed by suspending powdered samples into an aerosol laser ablation mass spectrometer (LAMS). PM sources studied included vehicle exhaust particulates, dust from a non-ferrous smelter, cement powder, incinerator fly ash, two coal fly ash samples, and two soils. Marker peaks signified certain PM source sectors: construction particles could be distinguished by abundant Ca and Ca compounds, fuel combustion was marked by elemental carbon clusters, and nonferrous industrial particles showed inorganic As, Cu, Pb, Zn, and SOx. In addition to the distinction between particles from these different source sectors, mass spectral results also showed that for a single source, different particle types existed, and among different sources within a sector, similar spectra were present. The aerosol LAMS results show the difficulty in differentiating among separate fly ash sources as well as among different soil samples. A particle class balance receptor model that measures the amount of specific particle types rather than the amount of a chemical component is suggested as a means of source apportionment when particle spectra with overlapping source possibilities occur. The assumptions and limitations of receptor modeling aerosol LAMS data are also described. In particular, methods need to be developed to account for the contribution of secondary sources.