Kinetic assessment of the potassium ferrate(VI) oxidation of antibacterial drug sulfamethoxazole

Sulfamethoxazole (SMX), a worldwide-applied antibacterial drug, was recently found in surface waters and in secondary wastewater effluents, which may result in ecotoxical effects in the environment. Herein, removal of SMX by environmentally-friendly oxidant, potassium ferrate(VI) (K(2)FeO(4)), is sought by studying the kinetics of the reaction between Fe(VI) and SMX as a function of pH (6.93-9.50) and temperature (15-45 degrees C). The rate law for the oxidation of SMX by Fe(VI) is first-order with respect to each reactant. The observed second-order rate constant decreased non-linearly from 1.33+/-0.08 x 10(3) M(-1)s(-1) to 1.33+/-0.10 x 10(0) M(-1)s(-1) with an increase of pH from 7.00 to 9.50. This is related to protonation of Fe(VI) (HFeO(4)(-) <==> H(+) + FeO(4)(2-); pK(a,HFeO(4)) = 7.23) and sulfamethoxazole (SH <==> H(+) + S(-); pK(a,SH)=5.7). The estimated rate constants were k(11)(HFeO(4)(-) + SH) = 3.0 x 10(4) M(-1)s(-1), k(12)(HFeO(4)(-) + S(-)) = 1.7 x 10(2) M(-1)s(-1), and k(13) (FeO(4)(2-) + SH) = 1.2 x 10(0) M(-1)s(-1). The energy of activation at pH 7.0 was found to be 1.86+/-0.04 kJ mol(-1). If excess potassium ferrate(VI) concentration (10 microM) is used than the SMX in water, the half-life of the reaction using a rate constant obtained in our study would be approximately 2 min at pH 7. The reaction rates are pH dependent; thus, so are the half-lives of the reactions. The results suggest that K(2)FeO(4) has the potential to serve as an oxidative treatment chemical for removing SMX in water.     

Kinetics of OH radical reactions with dibenzo-p-dioxin and selected chlorinated dibenzo-p-dioxins

The pulsed laser photolysis/pulsed laser-induced fluorescence (PLP/PLIF) technique has been applied to obtain rate coefficients for OH + dioxin (DD) (k1), OH + 2-chlorodibenzo-p-dioxin (2-CDD) (k2), OH + 2,3-dichlorodibenzo-p-dioxin (2,3-DCDD) (k3), OH + 2,7-dichlorodibenzo-p-dioxin (2,7-DCDD) (k4), OH + 2,8-dichlorodibenzo-p-dioxin (2,8-DCDD) (k5), OH + 1,2,3,4-tetrachlorodibenzo-p-dioxin (1,2,3,4-TCDD) (k6), and OH + octachlorodibenzo-p-dioxin (OCDD) (k7) over an extended range of temperature. The atmospheric pressure (740 +/- 10 Torr) rate measurements are characterized by the following Arrhenius parameters (in units of cm3 molecule(-1) s(-1), error limits are 1 omega): k1(326-907 K) = (1.70+/-0.22) x 10(-12)exp(979+/-55)/T, k2(346-905 K) = (2.79+/-0.27) x 10(-12)exp(784+/-54)/T, k3(400-927 K) = 10(-12)exp(742+/-67)/T, k4(390-769 K) = (1.10+/-0.10) x 10(-12)exp(569+/-53)/T, k5(379-931 K) = (1.02+/-0.10) x 10(-12)exp(580+/-68)/T, k6(409-936 K) = (1.66+/-0.38) x 10(-12)exp(713+/-114)/T, k7(514-928 K) = (3.18+/-0.54) x 10(-12)exp(-667+/-115)/T. The overall uncertainty in the measurements, taking into account systematic errors dominated by uncertainty in the substrate reactor concentration, range from a factor of 2 for DD, 2-CDD, 2,3-DCDD, 2,7-DCDD, and 2,8-DCDD to +/- a factor of 4 for 1,2,3,4-TCDD and OCDD. Negative activation energies characteristic of an OH addition mechanism were observed for k1-k6. k7 exhibited a positive activation energy. Cl substitution was found to reduce OH reactivity, as observed in prior studies at lower temperatures. At elevated temperatures (500 K < T < 500 K), there was no experimental evidence for a change in reaction mechanism from OH addition to H abstraction. Theoretical calculations suggest that H abstraction will dominate OH reactivity for most if not all dioxins (excluding OCDD) at combustion temperatures (>1000 K). For OCDD, the dominant reaction mechanism at all temperatures is OH addition followed by Cl elimination.     

Kinetic studies of the reaction of hydroxyl radicals with trichloroethylene and tetrachloroethylene

Rate coefficients are reported for the gas-phase reaction of the hydroxyl radical (OH) with C2HCl3 (k(1)) and C2Cl4 (k2) over an extended temperature range at 740+/-10 Torr in a He bath gas. These absolute rate measurements were accomplished using a laser photolysis/laser-induced fluorescence (LP/LIF) technique under slow flow conditions. The simple Arrhenius equation adequately describes the low temperature data for k1 (<650 K) and the entire data set for k2 and is given by (in units of cm3 molecule(-1) s(-1)): k1(291 - 650 K) = (9.73+/-1.15) x 10(-13) exp (158.7+/-44.0)/T, k2(293 - 720 K ) = (1.53+/-0.14) x 10(-12) exp (-688.2+/-67.5)/T. Error limits are 2sigma values. The room temperature values for k1 and k2 are within +/-2sigma of previous data using different techniques. The Arrhenius activation energies for k1 and k2 are a factor of 2-3 lower than previously reported values. The experimental measurements for both k1 and k2 in conjunction with transition state and variation transition state theory calculations infer an OH addition mechanism. The lack of a measurable kinetic isotope effect for k1 is consistent with this mechanism. Insight into the subsequent reactions of the chemically activated intermediate are presented in the form of potential energy diagrams derived from ab initio calculations.     

Chlorination of bisphenol A: kinetics and by-products formation

The kinetics of initial chlorination of bisphenol A (BPA) was studied between pH 2 and 11 at room temperature (20 +/- 2 degrees C). pH Profile of the apparent second-order rate constant of the reaction of BPA with chlorine were modeled considering the elementary reactions of HOCl with BPA species and an acid-catalyzed reaction. The predominant reactions at near neutral pH were the reactions of HOCl with the two phenolate species of BPA (k = 3.10 x 10(4) M(-1)s(-1) for BPA- and 6.62 x 10(4) M(-1) s(-1) for BPA(2-)). At near neutral pH, half-life times of BPA were calculated to be less than 1.5 h for chlorine residual higher than 0.2 mg l(-1). Chlorination of synthetic treated waters spiked with BPA showed that BPA disappeared within 4 h and that chlorinated bisphenol A congeners were rapidly formed and remained in solution for up to 10-20 h when low chlorine dosages are applied (0.5-1 mg l(-1)). To limit their presence in drinking water networks, it is then necessary to maintain high chlorine residuals that rapidly produce and decompose chlorinated bisphenol A congeners.     

Kinetics of photodegradation and ozonation of pentachlorophenol

The oxidation of 2,3,4,5,6-pentachlorophenol (PCP) has been carried out by a photodecomposition process using a polychromatic UV irradiation, and by an ozonation process. In the photodegradation process, the pH accelerated the decomposition rate and the approximate first-order rate constants were evaluated, with values between 0.16+/-0.005 min(-1) at pH=3 and 0.26+/-0.007 min(-1) at pH=9. A more rigorous kinetic study led to the determination of the quantum yields of the reaction, with values of 200+/-7x10(-3) mol/Eins for pH=3 and 22+/-1.1x10(-3) mol/Eins for pH=9. In the ozonation process, the rate constants for the reaction between ozone and PCP were determined by means of a competition kinetics, with values in the range from 0.67x10(5) to 314x10(5) l/mols. The specific rate constants for the un-dissociated and dissociated forms of PCP were also calculated. Finally, in both processes, the intermediate reaction products were identified, the most important being tetrachlorocatechol, tetrachlorohydroquinone and tetra-p-chlorobenzoquinone. Free chloride ion released, which was favored at high pHs, was also followed in both processes.     

Kinetics and mechanism of nitrite oxidation by hypochlorous acid in the aqueous phase

The rate coefficient for the reaction of nitrite with hypochlorite and hypochlorous acid has been studied using spectrophotometric measurements. The reaction rate has been determined in a wide range of H(+) concentration (5< or =-log[H(+)]< or =11). The kinetics were carried out as a function of NO(2)(-), H(+) and total hypochlorite ([HOCl](total)=[HOCl]+[ClO(-)]+[ClNO(2)]) concentrations. The observed overall rate law is described by: -d[HClO](T)dt=[a[NO(2)(-)](2)+b[NO(2)(-)]][H(+)](2)c+d[H(+)]+e[NO(2)(-)][H(+)](2)[HOCl](total)At T=298 K and in Na(2)SO(4) at an ionic strength (I=1.00 M), we obtained using a nonlinear fitting procedure: a=(1.83+/-0.36)x10(7) s(-1), b=(1.14+/-0.23)x10(5) Ms(-1), c=(1.12+/-0.17)x10(-13) M, d=(1.43+/-0.29)x10(-6) M(2) and e=(1.41+/-0.28)x10(3) M where the errors represent 2sigma. According to the overall rate law, a/b=k(1)/k(3), b/e=k(3), c=K(w), d/c=K(a), d=K(a)K(w) and e=K(1)K(a). In Na(2)SO(4) at an ionic strength (I=1.00 M), the values of K(1) and K(a) are (1.1+/-0.1)x10(-4) and 1.28x10(7) M(-1), respectively. A mechanism is proposed for the NO(2)(-) oxidation which involves the reversible initial step: NO(2)(-)+HOCl left harpoon over right harpoon ClNO(2)+OH(-) (K(1)), while ClNO(2) undergoes the two parallel reactions: attack by NO(2)(-) (k(1)) and hydrolysis (k(3)). ClNO(2) and N(2)O(4) are proposed as important intermediates as they control the mechanism. The rate coefficients k(1) and k(3) have been determined at different ionic strengths in NaCl and Na(2)SO(4). The influence of the ionic strength and ionic environment has been studied in this work.     

Catalytic effect of soil colloids on the reaction between CrVI and p-methoxyphenol

Adsorption of CrVI and p-methoxyphenol (PMP) on soil colloids at different pH media was studied. The resulting k1 and n of 1.89 x 10(2) and 0.53 (r2 = 0.99) and k2 and b of 0.13 and 1.25 x 10(3) (r2 = 0.96) were obtained from Freundlich (Q = k1Caqn) and Langmuir [Q = k2bCaq/(1 + k2Caq)] simulation equations, respectively, for CrVI adsorption on soil colloids (pH 4.20). The adsorption of PMP on soil colloids in pH 5.72 media was simulated by five different equations and the results indicated that the Fritz-Schluender one (r2 = 1.00) was the most suitable among them. Adsorption quantity of CrVI and PMP on colloids increased with increasing acidity in the pH range of 3.5-9.0. Study of CrVI adsorption kinetics indicated that the adsorption equilibrium of CrVI was reached rapidly within 2 h. In pure aqueous solution, CrVI reduction by PMP was observed only when the media's pH was lower than 4.0. Oxidation and reduction reaction between CrVI and p-methoxyphenol obviously occurred when soil colloids were involved in this system, even at pH > or = 7.0, which strongly suggested that minerals in soil colloids acted as catalysts to speed the reaction of CrVI and PMP. The oxidized product of PMP by CrVI, extracted by chloroform in acid media and analyzed by gas chromatography-mass spectrometry, was identified as benzoquinone. The reaction included two steps of one electron process.     

A laser flash photolysis study of the decay of SO4- and Cl2- radical anions in the presence of Cl- in aqueous solutions

The rate constant for the reaction of sulphate radical (SO4-) with Cl- has been determined using laser photolysis, at 248 nm, of peroxodisulphate anions to produce the radicals and time resolved optical absorption of the transient species (at 450 or 480 nm for SO4- and 350 nm for Cl2-) for the kinetic determinations. The experiments were performed, in the absence of added sulphate, as a function of temperature and ionic strength and yielded (at an ionic strength of 0.0157 M): kIV = (9.90+/-0.16) x 10(9) exp((-7.12+/-2.0) kJ mol(-1)/RT) M(-1) s(-1), where the errors reflect the 2sigma statistical error. This reaction produces Cl2-, the formation and decay of which were also monitored allowing a determination of the rate constant of its second-order self-recombination reaction which gave k = (6.50+/-1.40) x 10(8) M(-1) s(-1) at 293 K and zero ionic strength.     

Catalytic ozonation of 2,4-dichlorophenoxyacetic acid using alumina in the presence of a radical scavenger

Using a laboratory-scale mixed reactor, the performance of alumina in degrading 2,4-Dichlorophenoxyacetic acid with ozone in the presence of tert-butyl alcohol radical scavenger was studied. The operating variables investigated were the dose of alumina catalyst and solution pH. Results showed that using ozone and alumina leads to a significant increase in 2,4-D removal in comparison to non-catalytic ozonation and adsorption processes. The observed reaction rate constants (k(obs)) for 2,4-D during ozonation were found to increase linearly with increasing catalyst dose. At pH 5, the k(obs) value increased from 19.3 to 26 M(-1) s(-1) and 67 M(-1) s(-1) when varying the alumina dose from 1 to 2 and 4 g L(-1), respectively. As pH was increased, higher reaction rates were observed for both non-catalytic ozonation and catalytic ozonation processes. Thus, at pH 3 and using a catalyst dose of 8 g L(-1), the k(obs) values for non-catalytic ozonation and catalytic ozonation processes were 3.4 and 58.9 M(-1) s(-1), respectively, whereas at pH 5 reaction rate constants of 6.5 and 128.5 M(-1) s(-1) were observed, respectively. Analysis of total organic carbon suggested that catalytic ozonation with alumina achieved a considerable level of mineralization of 2,4-D. Adsorption of 2,4-D on alumina was found to play an important role in the catalytic ozonation process.     

Effect of pH and temperature on the kinetics of odor oxidation using chlorine dioxide

Increasing public concerns over odors and air regulations in nonattainment zones necessitate the remediation of a wide range of volatile organic compounds (VOCs) generated in the poultry-rendering industry. Currently, wet scrubbers using oxidizing chemicals such as chlorine dioxide (ClO2) are utilized to treat VOCs. However, little information is available on the kinetics of ClO2 reaction with rendering air pollutants, limiting wet scrubber design and optimization. Kinetic analysis indicated that ClO2 does not react with hexanal and 2-methylbutanal regardless of pH and temperature and implied that aldehyde removal occurs primarily via mass transfer. Contrary to the aldehydes, ethanethiol or ethyl mercaptan (a model compound for methanethiol or methyl mercaptan) and dimethyl disulfide (DMDS) rapidly reacted with ClO2. The overall reaction was found to be second and third order for ethanethiol and DMDS, respectively. Moreover, an increase in pH from 3.6 to 5.1 exponentially increased the reaction rate of ethanethiol (e.g., k2 = 25-4200 L/mol/sec from pH 3.6 to 5.1) and significantly increased the reaction rate of DMDS if increased to pH 9 (k3 = 1.4 x 10(6) L2/mol2/sec). Thus, a small increase in pH could significantly improve wet scrubber operations for removal of odor-causing compounds. However, an increase in pH did not improve aldehyde removal. The results explain why aldehyde removal efficiencies are much lower than methanethiol and DMDS in wet scrubbers using ClO2.     

Electrochemical monitoring of methylparathion degradation in an acid aqueous medium in presence of Cu(II)

A study was undertaken to determine the effect of Cu(II) in degradation of methylparathion (o,o-dimethyl o,4-nitrophenyl phosphoriotioate) in acid medium. Initial electrochemical characterization of Cu(II) and methylparathion was done in an aqueous medium at a pH range of 2-7. Cu(II) was studied in the presence of different anions and it was observed that its electroactivity depends on pH and is independent of the anion used. Methylparathion had two reduction signals at pH < or = 6 and only one at pH > 6. The pesticide's transformation kinetic was then studied in the presence of Cu(II) in acid buffered aqueous medium at pH values of 2, 4, and 7. Paranitrophenol appeared as the only electroactive product at all three pH values. The reaction was first order and had k values of 5.2 x 10(-3) s(-1) at pH 2, 5.5 x 10(-3) s(-1) at pH 4 and 9.0 x 10(-3) s(-1) at pH 7. It is concluded that the principal degradation pathway of methylparathion in acid medium is a Cu(II) catalyzed hydrolysis reaction.     

Kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE)

The kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE) in aqueous solutions at various pH, temperature, oxidant concentration and ionic strength levels was studied. The MTBE degradation was found to follow a pseudo-first-order decay model. The pseudo-first-order rate constants of MTBE degradation by persulfate (31.5 mM) at pH 7.0 and ionic strength 0.11 M are approximately 0.13 x 10(-4), 0.48 x 10(-4), 2.4 x 10(-4) and 5.8 x 10(-4) S(-1) at 20, 30, 40 and 50 degrees C, respectively. Under the above reaction conditions, the reaction has an activation energy of 24.5 +/- 1.6 kcal/ mol and is influenced by temperature, oxidant concentration, pH and ionic strength. Raising the reaction temperature and persulfate concentration may significantly accelerate the MTBE degradation. However, increasing both pH (over the range of 2.5-11) and ionic strength (over the range of 0.11-0.53 M) will decrease the reaction rate. Reaction intermediates including tert-butyl formate, tert-butyl alcohol, acetone and methyl acetate were observed. These intermediate compounds were also degraded by persulfate under the experimental conditions. Additionally, MTBE degradation by persulfate in a groundwater was much slower than in phosphate-buffer solutions, most likely due to the presence of bicarbonate ions (radical scavengers) in the groundwater.     

Photochemical behavior of parathion in the presence of humic acids from different origins

This paper reports the effect of ultraviolet radiation on the degradation of pesticide ethyl parathion in the presence of humic acids. Ethyl parathion was completely degraded in 300 min using an artificial lamp of 7.41 x 10(-10) einstein/s. Humic acid from peat did not influence the photochemical rate (k = 8.92 x 10(-3) min). However, in the presence of aquatic humic acid, the photochemical rate was higher (11.5 x 10(-3) min). The analytical determinations show the presence of p-nitrophenol and aminophenol in the reaction medium during the photochemical experiments. The kinetic of degradation in all experiments obeyed a first-order reaction pattern.     

Effect of Fe (III) on acid degradation of methylparathion

A study was undertaken to determine the transformation kinetic of methylparathion (O, O, -dimethyl O-4 nitrophenylphosphorotioate) in the presence of Fe(III) between pH 2 and 7. The Fe(III) was not electroactive under the conditions used in this study, and polarographic signals were exhibited by methylparathion and main degradation product only. Data suggest that hydrolysis of methylparathion in an acid medium is catalyzed by Fe(III) and the pesticide did not degrade in this medium without this cation. Methylparathion degradation was observed at all the pHs studied and was independent of the predominant chemical form of Fe(III) in the aqueous medium. The reaction was first-order with pH-dependent rate constant (k) values ranging from 3.3 x 10(- 3) h(- 1) to 7.0 x 10(- 3) h(- 1). The k values increased as pH decreased, suggesting that Fe(III) acted as an electrophile in the reaction mechanism.     

Lower variability of radionuclide activities in upland dairy products compared to soils and vegetation: implication for environmental survey

Contamination of the environment by radionuclides is usually estimated using soil and grass sampling. However, radionuclides are often not homogeneously distributed in soils. In the alpine Mercantour region (Western Alps, France) a large heterogeneity in Chernobyl 137Cs deposition has been previously observed. Here we report additional 137Cs results together with new 90Sr and Pu data for soil, grass, milk, and cheese samples. The results show that radioisotopes from nuclear weapons tests fallout are more homogeneously distributed than Chernobyl 137Cs. Further, we observe that the 137Cs and 90Sr contents are less variable in milk samples than in grass or soil samples. This can be attributed to the homogenization effect of cow vagrancy during grazing. Hence milk seems to be a more robust sample than soil or grass to evaluate the extent of contamination on a regional scale. We explore this idea by comparing own unpublished 90Sr results and 90Sr results from the literature to establish the relationship between altitude of grazing and contamination of soil and milk for Western Europe. There is a significant positive correlation between soil contamination and altitude and an even closer correlation between milk 90Sr activity (A) and altitude (h): A = A0 + e(k x h) where A0 is the expected activity of milk sampled at sea level (A0 = 0.064 +/- 0.014 Bq g(-1) Ca) and h is the altitude of grazing, k being a constant (k = 0.95 x 10(-3) +/- 0.11 x 10(-3) m(-1) Bq g(-1) Ca). The fact that there is less scattering in the relationship for the 90Sr(milk)-altitude than for 90Sr(soil)-altitude suggests, again, that milk is a well-suited sample for environmental survey. The relationship between the altitude of grazing and the 90Sr content of milk and cheese can also be used to assess the authenticity of dairy products.     

Rapid removal of flutriafol in water by zero-valent iron powder

A study of the effect of zero-valent iron (ZVI) powder is carried out for the first time on the degradation of flutriafol ((RS)-2,4'-difluoro-alpha-(1H-1,2,4-triazol-1-ylmethyl)-benzhydryl alcohol, C(16)H(13)F(2)N(3)O), a bifluorinated soil and water persistent triazole pesticide using a laboratory scale device consisting of a 20 ml pyrex serum vials fixed to a Vortex agitator. Different amounts of ZVI powder (10-50 g l(-1)) at pH 6.6 and room temperature were investigated. Experiments showed an observed degradation rate k(obs) directly proportional to the surface of contact of flutriafol with ZVI. Flutriafol degradation reactions demonstrated first order kinetic with a half-live of about 10.8+/-0.5 min and 3.6+/-0.2 min when experiments were conducted at [ZVI]=10 g l(-1) into oxygenated and anoxic solutions, respectively. Three analytical techniques were employed to monitor flutriafol degradation and to understand solution and by-products behaviors: (1) A UV-Vis spectrophotometer; (2) a high performance liquid chromatography (HPLC) coupled with a photo diode array (PDA) and fluorescence detectors; (3) a similar HPLC coupled with a PDA and a mass spectrometer detectors equipped with an atmospheric pressure photoionization source. Results showed a complete disappearance of flutriafol after 20 min of contact with ZVI, the loss of fluorescence properties of the final by-products, the defluorination of the triazole pesticide via hydroxylation reaction and finally the hydrogenation of the triazole ring.     

Kinetics of the chemical degradation of diuron

The influence of pH and buffer concentration on the chemical degradation of diuron in water has been analysed over a wide temperature range. The process irreversibly gives 3,4-dichloroaniline as the only product containing the phenyl ring. H+, OH- and phosphate buffer are efficient catalysts of the reaction. The rate constant first increases rapidly at low buffer concentrations and then gradually levels off at higher ones. At 40 degrees C and high phosphate concentration (>0.01 M), or in the extreme pH regions, the half-life is approximately 4 months and the activation energy is 127 +/- 2 kJmol(-1).     

Hydrogen peroxide-assisted UV photodegradation of Lindane

Aqueous solutions of gamma-hexachlorocyclohexane (Lindane) were photolyzed (lambda=254 nm) under a variety of solution conditions. The initial concentrations of hydrogen peroxide (H(2)O(2)) and Lindane varied from 0 to 20 mM and 0.21 to 0.22 microM, respectively, the pH ranged from 3 to 11, and several concentration ratios of Suwannee River humic acid and fulvic acid were dissolved in the irradiated solutions. Lindane rapidly reacted, and the maximum reaction rate constant (9.7 x 10(-3) s(-1)) was observed at pH 7 and initial [H(2)O(2)]=1 mM. Thus, 90% of the Lindane is destroyed in approximately 4 min under these conditions. In addition, within 15 min, all chlorine atoms were converted to chloride ion, indicating that chlorinated organic by-products do not accumulate. The reactor was characterized by measuring the photon flux (7.04 x 10(-6) E s(-1)) and the cumulative production of *OH during irradiation. The cumulative *OH production during irradiation was fastest at an initial [H(2)O(2)]=5 mM (k=0.77 micro M s(-1)).     

Removal of selected endocrine disrupting chemicals and personal care products in surface waters and secondary wastewater by ozonation

This study investigated the removal of parabens, N,N-diethyl-m-toluamide (DEET), and phthalates by ozonation. The second-order rate constants for the reaction between selected compounds with ozone at pH 7 were of (2.2 +/-0.2) X 10(6) to (2.9 +/-0.3) X 10(6) M 1/s for parabens, (2.1+/- 0.3) to (3.9 +/-0.5) M-1/s for phthalates, and (5.2 +/-0.3) M-1/s for DEET. The rate constants for the reaction between selected compounds with hydroxyl radical ranged from (2.49 +/-0.06) x 10(9) to (8.5 +/-0.2) x 10(9) M-1/s. Ozonation of selected compounds in secondary wastewater and surface waters revealed that ozone dose of 1 and 3 mg/L yielded greater than 99% depletion of parabens and greater than 92% DEET and phthalates, respectively. In addition, parabens were found to transform almost exclusively through the reaction with ozone, while DEET and phthalates were transformed almost entirely by hydroxyl radicals (.OH).     

Influence of sorption to dissolved humic substances on transformation reactions of hydrophobic organic compounds in water. Part II: hydrolysis reactions

The effect of dissolved humic acid (HA) on two types of hydrolysis reactions was investigated: (I) dehydrochlorination of gamma-hexachlorocyclohexane (HCH) and 1,1,2,2-tetrachloroethane (TeCA) as a reaction involving hydroxide ions (OH(-)) and (II) hydrolysis of 1-octyl acetate (OA) which is catalyzed by H(+) at the applied pH value (pH 4.5). The rate of TeCA hydrolysis was not affected by addition of 2 g l(-1) of HA at pH 10 (k' = 0.33 h(-1)) but HCH hydrolysis was significantly inhibited (k' = 4.6 x 10(-3) h(-1) without HA and 2.8 x 10(-3)h(-1) at 2 g l(-1) HA). HCH is sorbed by 51% whereas TeCA sorption is insignificant at this HA concentration. Sorbed HCH molecules are effectively protected due to electrostatic repulsion of OH(-) by the net negative charge of the HA molecules. In contrast, OA hydrolysis at pH 4.5 (k' = 1.6 x 10(-5) h(-1)) was drastically accelerated after addition of 2 g l(-1) HA (k' = 1.1 x 10(-3) h(-1)). The ratio of the pseudo-first-order rate constants of the sorbed and the freely dissolved ester fraction is about 70. H(+) accumulation in the microenvironment of the negatively charged HA molecules was suggested to contribute to the higher reaction rate for the sorbed fraction in case of this H(+)-catalyzed reaction. Analogous effects from anionic surfactants are known as micellar catalysis.