A preliminary process design and economic assessment of a catalyst rejuvenation process for waste disposal of refinery spent catalysts

Spent hydroprocessing catalysts from refineries have been classified as hazardous solid waste by the United States Environmental Protection Agency (USEPA), refiners must find a viable but economical solution to solve this serious environmental issue. Catalyst rejuvenation is an attractive option for minimizing the environmental problems associated with spent catalysts. In this study, a preliminary design for such a process and the corresponding economic analysis are performed to assess the proposed catalyst rejuvenation process for metal-fouled spent catalysts generated in residue hydroprocessing units. The scenarios used in the economic assessment are based on three options of process synthesis and two operator modes. It is found that the option of rejuvenating medium and lightly fouled spent catalyst produced by the refinery will be the best solution for refiners, both environmentally and economically.     

Production of bio-oil from algal biomass and its upgradation to biodiesel using CaO-based heterogeneous catalysts

The present article deals with the production of bio-oil from algal biomass as well as the preparation and characterization of noble CaO-based heterogeneous catalyst for upgradation of bio-oil to biodiesel. The bio-oil has been extracted from algal biomass using hexane as solvent in soxhlet apparatus and upgraded to biodiesel by transesterification using noble CaO-based heterogeneous catalysts. Catalyst with TiO₂:CaO molar ratio of 0.25 and calcination temperature of 700°C has been found to be most suitable among all the catalysts developed. Characterization of the catalysts has been done by using X-ray diffraction (XRD), scanning electron microscope (SEM), and thermo-gravimetric analysis (TGA). The input--output model has been developed to correlate experimental and predicted value of biodiesel yield. Optimization of process parameters has been done using response surface methodology. Various properties and elemental composition of algal bio-oil and biodiesel have been determined and compared with biodiesel.     

Utilization of pulp and paper industrial wastes to remove heavy metals from metal finishing wastewater

Two pulp and paper industrial wastes, lime mud (LM) and recovery boiler ash (RB), have low moisture contents, low heavy metal contaminations and contain various carbonate compounds which contribute to a high pH. Metal finishing wastewater (MF-WW) has a low pH, high levels of TDS and high contaminations from Cr, Cu, Pb and Zn. The heavy metals from MF-WW were removed by sorption and precipitation mechanisms. LM gave better results in removing heavy metals from MF-WW than RB. At a reaction time of 45 min, the maximum removal efficiencies for Cr (93%) and Cu (99%) were obtained at 110 g L⁻¹ of LM, but at 80 g L⁻¹ for Pb (96%) and Zn (99%). Treatment with LM gives a higher sludge volume than with RB. However, the leachability of heavy metals from LM is lower. Leachability of heavy metals in the sediment for all selected treatment conditions is within government standards.     

用清洗特殊钢废酸生产聚铁净水剂及其Mn,Cr,Ni量的测定

本文论述了长城特钢四厂在用酸洗特殊钢废酸生产聚铁净水剂中的重金属离子间问题及其废酸中Ｍｎ，Ｃｒ，Ｎｉ量的测定。     

Characteristics of heavy metals and Pb isotopic signatures in sediment cores collected from typical urban shallow lakes in Nanjing, China

To investigate the contamination levels and sources for heavy metals that have occurred during the development of cities, sediment cores collected from typical urban shallow lakes (Xuanwu Lake and Mochou Lake) in Nanjing, China were analyzed for Cu, Pb, Zn, Cd, Cr, Ni, and for Pb stable isotopic ratios. No significant differences were found in the concentrations of Cu, Ni and Cd among sediment layers from Xuanwu or in the levels of Cr and Ni among sediment layers from Mochou. However, there were significant differences among the layers in the concentrations of Cr, Zn and Pb in Xuanwu and Cu, Zn, Cd and Pb in Mochou. Based on geoaccumulation indexes and enrichment factors, Cd was the primary pollutant at all depths in the sediment cores. The ratios of (206)Pb/(207)Pb and (208)Pb/(206)Pb differ significantly among sediment layers in Xuanwu. No significant differences were found on the ratios of (208)Pb/(206)Pb in Mochou, but the ratios of (206)Pb/(207)Pb differ significantly among some of the sediment layers in Mochou. The range of (208)Pb/(206)Pb and (206)Pb/(207)Pb ratios was found to be 2.098-2.106 and 1.170-1.176, respectively, for sediment cores from Mochou Lake and 2.091-2.104 and 1.168-1.183, respectively, for cores from Xuanwu Lake. The differences in heavy metal concentrations and the Pb isotopic ratios with depth for the cores from Xuanwu and Mochou confirmed that the contamination sources changed during the formation of the different sediment layers. Furthermore, the ratios of (206)Pb/(207)Pb demonstrated that gasoline and vehicular Pb were not the primary sources of Pb contamination at different depths in the sediment cores in Xuanwu Lake and Mochou Lake.