Equilibrium and kinetic studies on the adsorption of aniline compounds from aqueous phase onto bifunctional polymeric adsorbent with sulfonic groups

In the present study, a hydrophilic bifunctional polymeric resin (LS-2) with sulfonic groups was synthesized, and the adsorption performance of three aniline compounds, aniline, 4-methylaniline, and 4-nitroaniline onto LS-2 was compared with that on the commercial Amberlite XAD-4. The uptake of the aniline compounds on LS-2 is a procedure of coexistence of physisorption and chemisorption and obeys the pseudo-second order rate equation, while the uptake of the compounds on XAD-4 is merely a physical adsorption and follows the pseudo-first order rate equation. All the isothermal data fit well with the Freundlich model, and the values of K(F) of the compounds adsorbing on LS-2 are much higher than those on XAD-4 suggesting the higher adsorbing capacities on LS-2 than those on XAD-4, which may be attributed to the microporous structure and the polar groups on the network of LS-2 resin. Dynamic adsorption and desorption studies for aniline on LS-2 show that the breakthrough adsorption capacity and the total adsorption capacity are 0.96 and 1.24 mmol per milliliter resin, respectively. Nearly 100% regeneration efficiency for the adsorbent was achieved by 5% hydrochloric acid.     

Comparison of modified montmorillonite adsorbents. Part II: The effects of the type of raw clays and modification conditions on the adsorption performance

This paper builds on the preceding researches to study the effects of the type of clays (montmorillonites K10, KSF) and modifying conditions on the structure and adsorption behavior of resulting clay adsorbents. The raw clays were modified by polymeric Al/Fe species, hexadecyl-trimethylammonium (HDTMA) surfactant and a complex of polymeric Al/Fe-HDTMA. X-ray diffraction spectra was applied to analyze the structure of the raw and modified clays. After modification, the basal spacing of the clays varied, depending on the types of raw clay and modification conditions. Copper and phenol were selected as adsorbates for evaluating the adsorption performance of various clays, which was affected significantly by the types of raw clay and modification conditions. In general the inorganic contaminant (e.g., Cu) tend to be adsorbed by the polymeric Al/Fe modified clay and the organic impurities (e.g., phenol) will be preferably captured by the surfactant modified clay; both due to the specific surface properties resulting from introducing the modifiers. The complex modified clays possessed the ability of adsorbing both inorganic and organic contaminants. In addition, the d 0 0 1 spacing of modified KSF was greater than that of K10; the adsorption performance with modified KSF was thus greater than that with the modified K10. Finally, the ratio of modifiers to the clay (metal:surfactant:clay) has been observed to affect the adsorption performance; the optimal conditions have been defined.     

Adsorption properties of kaolinite-based nanocomposites for Fe and Mn pollutants from aqueous solutions and raw ground water: kinetics and equilibrium studies

Raw kaolinite was used in the synthesis of metakaolinite/carbon nanotubes (K/CNTs) and kaolinite/starch (K/starch) nanocomposites. Raw kaolinite and the synthetic composites were characterized using XRD, SEM, and TEM techniques. The synthetic composites were used as adsorbents for Fe and Mn ions from aqueous solutions and natural underground water. The adsorption by the both composites is highly pH dependent and achieves high efficiency within the neutral pH range. The experimental adsorption data for the uptake of Fe and Mn ions by K/CNTs were found to be well represented by the pseudo-second-order kinetic model rather than the intra-particle diffusion model or Elovich model. For the adsorption using K/starch, the uptake results of Fe ions was well fitted by the second-order model, whereas the uptake of Mn ions fitted well to the Elovich model rather than pseudo-second-order and intra-particle diffusion models The equilibrium studies revealed the excellent fitting of the removal of Fe and Mn ions by K/CNTs and Fe using K/starch with the Langmuir isotherm model rather than with Freundlich and Temkin models. But the adsorption of Mn ions by K/starch is well fitted with Freundlich rather than Temkin and Langmuir isotherm models. The thermodynamic studies reflected the endothermic nature and the exothermic nature for the adsorption by K/CNTs and K/starch nanocomposites, respectively. Natural ground water contaminated by 0.4 mg/L Fe and 0.5 mg/L Mn was treated at the optimum conditions of pH 6 and 120 min contact time. Under these conditions, 92.5 and 72.5% Fe removal efficiencies were achieved using 20 mg of K/CNTs and K/starch nanocomposites, respectively. Also, K/CNTs nanocomposite shows higher efficiency in the removal of Mn ions as compared to K/starch nanocomposite.     

水溶液中腐殖酸和苯酚在ZH-02树脂上的双组分吸附

通过苯甲酰基修饰的苯乙烯-二乙烯苯吸附树脂ZH-02对水中腐殖酸和苯酚进行了单组分和双组分的静态吸附.结果表明,在腐殖酸为主要吸附质的二元组分溶液中,对苯酚的吸附量的影响可以利用IAST模型进行预测;而在不存在主要吸附质的二元溶液中,可以用单组分体系的平衡吸附量近似预算双组分竞争体系时各组分的平衡吸附量.     

水溶液中腐殖酸和苯酚在ZH-02树脂上的双组分吸附

通过苯甲酰基修饰的苯乙烯-二乙烯苯吸附树脂ZH-02对水中腐殖酸和苯酚进行了单组分和双组分的静态吸附.结果表明,在腐殖酸为主要吸附质的二元组分溶液中,对苯酚的吸附量的影响可以利用IAST模型进行预测;而在不存在主要吸附质的二元溶液中,可以用单组分体系的平衡吸附量近似预算双组分竞争体系时各组分的平衡吸附量.     

Adsorption of CO2 from flue gas streams by a highly efficient and stable aminosilica adsorbent

Three ordered mesoporous silicas (OMSs) with different pore sizes and pore architectures were prepared and modified with amine functional groups by a postgrafting method. The carbon dioxide (CO2) adsorption on these amine-modified OMSs was measured by using microbalances at 348 K, and their adsorption capacities were found to be 0.2-1.4 mmol g(-1) under ambient pressure using dry 15% CO2. It was found experimentally that the CO2 adsorption capacity and adsorption rate were attributed to the density of amine groups and pore volume, respectively. A simple method is described for the production of densely anchored amine groups on a solid adsorbent invoking direct incorporation of tetraethylenepentamine onto the as-synthesized OMSs. Unlike conventional amine-modified OMSs, which typically show CO2 adsorption capacity less than 2 mmol g(-1), such organic template occluded amine-OMS composites possessed remarkably high CO2 uptake of approximately 4.6 mmol g(-1) at 348 K and 1 atm for a dry 15% CO2/nitrogen feed mixture. The enhancement of 8% in CO2 adsorption capacity was also observed in the presence of 10.6% water vapor. Durability tests done by cyclic adsorption-desorption revealed that these adsorbents also possess excellent stability.     

Solution factors affecting the adsorption of phenol onto a siltstone

Phenolic compounds are a major pollution by-product of the underground coal gasification process. The adsorption of phenol onto a siltstone was studied using batch techniques and 1:1 crushed siltstone to solution slurries. The siltstone used was associated with a Wyoming coal deposit of a type similar to that which could be gasified in situ. The pH of the solution was found to be the major factor controlling the adsorption of phenol onto the siltstone. Phenol was adsorbed when the solution pH was less than the pKa while no sorption was observed at higher pH. Since in situ gasification sites have an elevated pH post gasification, phenolic compounds may be transported by groundwater in these regions. Significant differences were also found for the adsorption of phenol onto initially wet or dry adsorbate. Desorption studies were also performed. Langmuir and Freundlich adsorption isotherms were used to model the data.     

Adsorption of phenolic compounds by activated carbon--a critical review

Adsorption of phenol and its derivatives on activated carbons is considered based on numerous papers related to this issue. Special attention is paid to the effects of carbon surface functionalities, pH of solution and heterogeneity effects that accompany adsorption of phenolic compounds. Moreover, in this paper the most important aspects are overviewed referring to irreversible adsorption of phenols and impact of different substituents of phenolic compounds on their uptake by activated carbons is considered. Finally, some remarks pertaining to applications of novel adsorbents for phenol adsorption are discussed and illustrated by means of a few examples.     

Prediction of the adsorption capacity for volatile organic compounds onto activated carbons by the Dubinin-Radushkevich-Langmuir model

Prediction of the adsorption capacity for volatile organic compounds (VOCs) onto activated carbons is elucidated in this study. The Dubinin-Radushkevich (D-R) equation was first used to predict the adsorption capacity of nine aromatic and chlorinated VOCs onto two different activated carbons. The two key parameters of the D-R equation were estimated simply from the properties of the VOCs using quantitative structure-activity relationship and from the pore size distribution of the adsorbent. The approach based on the D-R equation predicted well the adsorption capacity at high relative pressures. However, at the relative pressures lower than -1.5 x 10(-3), the D-R approach may significantly overestimate adsorption capacity. To extrapolate the approach to lower relative pressures, the integration of the D-R equation and the Langmuir isotherm, called the D-R-L model, was proposed to predict adsorption capacity over a wide range of relative pressures of VOCs. In this model, the Langmuir isotherm parameters were extracted from the predicted D-R isotherm at high relative pressures. Therefore, no experimental effort was needed to obtain the parameters of the D-R-L model. The model successfully predicted the adsorption capacity of aromatic and chlorinated hydrocarbons tested onto BPL and Sorbonorit B carbons over relative pressures ranging from 7.4 x 10(-5) to 0.03, suggesting that the model is applicable at the low relative pressures of VOCs often observed in many environmental systems. In addition, the molecular size of organic compounds may be an important factor affecting the adsorption capacity of activated carbons. For BPL carbon, an ultramicroporous adsorbent, the limiting pore volume Wo of the D-R equation decreased when the kinetic diameter of the adsorbate was larger than 6 angstroms. However, for Sorbonorit B carbon, no reduction of Wo was found, suggesting that the Wo may be related to the pore size distribution of the adsorbents, as well as to their molecular size. This size exclusion effect may play an important role in predicting the adsorption capacity of VOCs onto microporous adsorbents in the D-R-L model and in the corresponding D-R equation.     

Silane removal at ambient temperature by using alumina-supported metal oxide adsorbents

Copper, zinc, and cerium oxide adsorbents supported on alumina were used to remove silane gas (SiH4). The adsorbents were prepared using a coprecipitation method and characterized by the inductively coupled plasma mass spectrometry, X-ray powder diffractometer, and Brunauer-Emmett-Teller method (BET). The silane removal efficiency and adsorption capacity of the adsorbents were investigated in this study. Test results showed that the adsorbents containing active species had a removal efficiency >99.9% for SiH4 before breakthrough. Adsorbents containing mixed oxides (CuO-CeO2/ Al2O3 and CuO-ZnO/Al2O3), which showed well-dispersed active species and high BET surface areas, had a greater adsorption capacity than the adsorbents containing single metal oxide. However, when the CuO-ZnO/ Al2O3 adsorbents contain >40 wt% of active metal oxides, the increase of active species lowered the BET surface area leading to a decrease of the adsorption capacity. Additionally, when the content of the active metal oxides was between 20% and 40%, the CuO-ZnO/Al2O3 adsorbents demonstrated higher adsorption capacity.     

Removal of acutely hazardous pharmaceuticals from water using multi-template imprinted polymer adsorbent

Molecularly imprinted polymer adsorbent has been prepared to remove a group of recalcitrant and acutely hazardous (p-type) chemicals from water and wastewaters. The polymer adsorbent exhibited twofold higher adsorption capacity than the commercially used polystyrene divinylbenzene resin (XAD) and powdered activated carbon adsorbents. Higher adsorption capacity of the polymer adsorbent was explained on the basis of high specific surface area formed during molecular imprinting process. Freundlich isotherms drawn showed that the adsorption of p-type chemicals onto polymer adsorbent was kinetically faster than the other reference adsorbents. Matrix effect on adsorption of p-type chemicals was minimal, and also polymer adsorbent was amenable to regeneration by washing with water/methanol (3:1, v/v) solution. The polymer adsorbent was unaltered in its adsorption capacity up to 10 cycles of adsorption and desorption, which will be more desirable in cost reduction of treatment compared with single-time-use activated carbon.     

Adsorption of phenol by bentonite

The potential of bentonite for phenol adsorption from aqueous solutions was studied. Batch kinetics and isotherm studies were carried out to evaluate the effect of contact time, initial concentration, pH, presence of solvent, and the desorption characteristics of bentonite. The adsorption of phenol increases with increasing initial phenol concentration and decreases with increasing the solution pH value. The adsorption process was significantly influenced by the solvent type in which phenol was dissolved. The affinity of phenol to bentonite in the presence of cyclohexane was greater than that in water and was lowest in the presence of methanol. Methanol was used to extract phenol from bentonite. The degree of extraction was dependent on the amount of phenol adsorbed by bentonite. X-ray diffraction analysis showed that the crystalline structure of bentonite was destroyed when cyclohexane was used. The ability of bentonite to adsorb phenol from cyclohexane decreased as the water to cyclohexane ratio was increased. Furthermore, hysteresis was observed in phenol desorption from bentonite in aqueous solutions. The equilibrium data in aqueous solutions was well represented by the Langmuir and Freundlich isotherm models. The removal of phenol from aqueous solutions was observed without surface modification.     

凹凸棒粘土对水中亚甲蓝的吸附性能

用焦磷酸钠和盐酸纯化了地产凹凸棒粘土,SEM、XRD和FT-IR表征其结构。研究了凹凸棒粘土对亚甲蓝的吸附性能及热力学和动力学特征,考察了吸附时间、温度、初始浓度、pH和离子强度下对亚甲蓝吸附的影响。结果表明,不同实验条件下,吸附过程均符合准二级动力学特征。凹凸棒粘土对亚甲蓝是放热的物理吸附过程,吸附符合Langmuir模式,在303 K时最大吸附量为114.02 mg/g。与其他吸附材料相比,凹凸棒粘土对亚甲蓝有较快的吸附速率和较大的吸附量,可以作为价廉的吸附剂用于亚甲蓝的消除。     

A method for measuring the anoxic biodegradability under denitrifying conditions

A test for assessing the anoxic biodegradability of organic compounds under denitrifying conditions is proposed. The method is based on the recovery and quantification of the CO2 produced, which is evidence of complete biodegradation of the test compound (added as the sole carbon source). The tests were carried out in a mineral medium, with nitrate as electron acceptor. Whole lake sediments, sediment extracts and a commercial inoculum were assayed as a possible inoculum source by means of glucose biodegradability tests. It was found that the sediment extracts constitute a suitable and environmentally-relevant inoculum source, since they add non-significant amounts of carbon to the tests. Two xenobiotic compounds, namely, aniline and phenol, were tested in the aforementioned conditions as well as in a standard aerobic biodegradability test. Both aniline and phenol attained a biodegradation level higher than 60% in a short time period (<28 days) and thus can be considered as readily biodegradable in denitrifying environments. Nevertheless, the kinetics obtained in the anoxic test were slower than in aerobic conditions, and even suggested the accumulation of intermediate metabolites in the case of phenol. The results of this study indicate that the fate of xenobiotic compounds under anoxic conditions differs from that observed in an oxic environment, and therefore it should be considered by standard biodegradability testing procedures.     

固定化改性蒙脱土对苯酚吸附性能的研究

利用十六烷基三甲基溴化铵对天然蒙脱土进行改性,并用聚乙烯醇对改性蒙脱土进行固定化处理,然后进行柱状吸附和振荡条件的吸附试验。研究结果表明,HDTMA改性蒙脱土固定化后能有效吸附苯酚,不同环境条件对苯酚的柱状吸附能力产生不同的影响。在pH4~8的范围内,固定化改性蒙脱土对苯酚的吸附效果无显著性差异,pH在10以上,其吸附能力明显下降;温度对吸附效果影响不大;进水苯酚浓度越高,改性蒙脱土对苯酚的吸附量越大,但出水苯酚浓度也高;苯酚的流速越小,吸附容量越高,吸附效果越好。     

The long-term effect of initial pH control on the enrichment culture of phosphorus- and glycogen-accumulating organisms with a mixture of propionic and acetic acids as carbon sources

In most studies on phosphorus- and glycogen-accumulating organisms (PAO and GAO), pH was controlled constantly throughout the entire anaerobic and aerobic periods, and acetic acid was used as the carbon source. In this paper, the effect of long-term initial pH values on PAO and GAO was investigated with mixed propionic and acetic acids as carbon sources. It was observed that with pH increasing from 6.4 to 8.0, the anaerobic propionic acid uptake rate by PAO linearly increased but that by GAO proportionally decreased. At pH 6.70 and pH 7.51, PAO and GAO exhibited the same acetic and propionic acid uptake rates, respectively. The acetic acid uptake rate by PAO was greater than that by GAO at pH > 6.70, and the propionic acid uptake rate by PAO was higher than that by GAO at pH > 7.51, which indicated that PAO would take predominance over GAO at pH > 7.51. Poly-3-hydroxybutyrate, poly-3-hydroxyvalerate and poly-3-hydroxy-2-methylvalerate shared 7%, 62% and 31%, respectively in the PAO system, and 11%, 44% and 45% respectively in the GAO system, and these fractions were observed independent of pH either in the PAO or in the GAO system. In the PAO system, with the increase of pH, the phosphorus removal efficiency was improved greatly, and a phosphorus removal efficiency of 100% was achieved at 8.0. Further investigation showed that the higher phosphorus removal efficiency at higher pH was mainly caused by a biological effect instead of chemical one.     

Solar photocatalytic degradation of mono azo methyl orange and diazo reactive green 19 in single and binary dye solutions: adsorbability vs photodegradation rate

The objective of this study was to examine the effects of adsorbability and number of sulfonate group on solar photocatalytic degradation of mono azo methyl orange (MO) and diazo Reactive Green 19 (RG19) in single and binary dye solutions. The adsorption capacity of MO and RG19 onto the TiO₂ was 16.9 and 26.8 mg/g, respectively, in single dye solution, and reduced to 5.0 and 23.1 mg/g, respectively, in the binary dye solution. The data obtained for photocatalytic degradation of MO and RG19 in single and binary dye solution were well fitted with the Langmuir–Hinshelwood kinetic model. The pseudo-first-order rate constants of diazo RG19 were significant higher than the mono azo MO either in single or binary dye solutions. The higher number of sulfonate group in RG19 contributed to better adsorption capacity onto the surface of TiO₂ than MO indicating greater photocatalytic degradation rate.     

纳米有机膨润土对苯酚的吸附性能研究

通过对天然膨润土改性,制备纳米有机膨润土并用于吸附苯酚,探讨了吸附时间、溶液pH、纳米有机膨润土投加量等因素对苯酚吸附的影响。结果表明,吸附在5 min内快速达到平衡,溶液pH可以影响苯酚在溶液中的状态,是影响苯酚吸附性能的重要因素。纳米有机膨润土吸附苯酚的过程可用伪二级反应动力学方程来描述,伪二级吸附速率常数为1.3 g/(mg.min)。吸附等温线符合Langmuir等温方程,在25℃时,Langmuir理论最大吸附容量可达到536.32 mg/g,吸附热力学参数表明吸附过程是自发的、放热的物理吸附过程。     

Removal of malachite green dye from wastewater by different organic acid-modified natural adsorbent: kinetics,equilibriums, mechanisms,practical application,and disposal of dye-loaded adsorbent

Natural adsorbent (Cinnamomum camphora sawdust) modified by organic acid (oxalic acid, citric acid, and tartaric acid) was investigated as a potential adsorbent for the removal of hazardous malachite green (MG) dye in aqueous media in a batch process. The extent of MG adsorption onto modified sawdust increased with increasing organic acid concentrations, pH, contact time, and temperature but decreased with increasing adsorbent dosage and ionic strength. Kinetic study indicated that the pseudo-second-order kinetic model could best describe the adsorption kinetics of MG. Equilibrium data were found to fit well with the Langmuir model, and the maximum adsorption capacity of the three kinds of organic acid-modified sawdust was 280.3, 222.8, and 157.5 mg/g, respectively. Thermodynamic parameters suggested that the sorption of MG was an endothermic process. The adsorption mechanism, the application of adsorbents in practical wastewater, the prediction of single-stage batch adsorption system, and the disposal of depleted adsorbents were also discussed.     

溴化十六烷基吡啶改性沸石对水中甲基橙的吸附

采用溴化十六烷基吡啶(CPB)对天然沸石进行改性制备得到了CPB改性沸石,通过批量吸附实验考察了CPB改性沸石对水中阴离子染料甲基橙的去除作用。结果表明,天然沸石对水中甲基橙的吸附能力很差,而CPB改性沸石则可以有效吸附去除水中的甲基橙。CPB改性沸石对水中甲基橙的吸附能力随CPB负载量的增加而增加,CPB负载量最大的改性沸石对水中甲基橙的吸附能力最强。双分子层CPB改性沸石对水中甲基橙的去除率随吸附剂投加量的增加而增加,而CPB改性沸石对水中甲基橙的单位吸附量则随吸附剂投加量的增加而降低。双分子层CPB改性沸石对水中甲基橙的吸附平衡数据可以采用Langmuir等温吸附模型加以描述。根据Langmuir模型计算得到的CPB负载量为341 mmol/(kg沸石)的双分子层CPB改性沸石对水中甲基橙的最大吸附容量为63.7 mg/g(303 K和pH 7)。准二级动力学模型适合用于描述双分子层CPB改性沸石对水中甲基橙的吸附动力学过程。pH和反应温度对双分子层CPB改性沸石吸附水中甲基橙的影响较小。以上结果说明,双分子层CPB改性沸石适合作为一种吸附剂用于去除废水中的甲基橙。