Degradation of polychlorinated dibenzo-p-dioxins in aqueous solution by Fe(II)/H2O2/UV system

The photodegradation of polychlorinated dibenzo-p-dioxins (PCDDs), which include tetra- to octa-CDDs (TeCDD, PeCDD, HxCDD, HpCDD and OCDD), was carried out in the presence of Fe(II) and H2O2 mixed reagent. The degradation efficiency was strongly influenced by UV irradiation, and the initial concentrations of H2O2 and Fe(II). An initial TeCDD concentration of 10 ng l(-1) was completely degraded within 20 min under the optimum conditions. All PCDDs tested were successfully degraded by Fe(II)/H2O2/UV treatment and complete degradation of TeCDD, PeCDD and HxCDD was achieved within 120 min. PCDD photodegradation rates decreased with the number of chlorine atoms. The degradation process of TeCDD by this system seems to be initiated by an oxidative reaction (OH* radical attack) because less chlorinated DDs as intermediate products were not detected. From the Frontier electron density calculation, the first OH* radical attack positions on TeCDD were found to be four C atoms neighboring two O atoms. The decomposition of TeCDD gave 4,5-dichlorocatechol as an intermediate product. A TeCDD degradation scheme was proposed based on the identified intermediate and the values of Frontier electron density. Based on these results, Fe(II)/H2O2/UV system could be useful technology for the treatment of wastewater containing persistent pollutants such as dioxins and polychlorinated biphenyls.     

Kinetics of low frequency sonodegradation of linear alkylbenzene sulfonate solutions

The decomposition of sodium dodecylbenzene sulfonate (SDBS) in water by means of ultrasound irradiation at 20kHz was investigated. Experiments were conducted at surfactant concentrations of 175, 260 and 350 mg l(-1), liquid volumes of 120, 170 and 220 ml, temperatures of 20, 30 and 45 degrees C and applied power of 40, 80 and 125 W. The extent of degradation was followed monitoring substrate and organic carbon concentrations, while hydrogen peroxide concentration was also measured; the latter is a product of water sonolysis due to hydroxyl radical recombination. 80% SDBS conversion was achieved after 120 min of sonication at 125 W and 30 degrees C; nonetheless, SDBS and its degradation intermediates proved difficult to oxidise as only about 20-25% of the initial carbon content was transformed to carbon dioxide. At the initial stages of the reaction, degradation rate appears to be only weakly dependent on the substrate concentration with the rate increasing from 3.1 to 4 mg l(-1)min(-1) with increasing concentration from 175 to 350 mg l(-1). Degradation appears to occur at the bubble-liquid interface through hydroxyl radical-mediated reactions whose role was established by performing experiments in the presence of radical scavengers, namely potassium bromide and sodium benzoate. Degradation rates increased with increasing power and decreasing temperature and volume.     

Effect of Fe (III) on acid degradation of methylparathion

A study was undertaken to determine the transformation kinetic of methylparathion (O, O, -dimethyl O-4 nitrophenylphosphorotioate) in the presence of Fe(III) between pH 2 and 7. The Fe(III) was not electroactive under the conditions used in this study, and polarographic signals were exhibited by methylparathion and main degradation product only. Data suggest that hydrolysis of methylparathion in an acid medium is catalyzed by Fe(III) and the pesticide did not degrade in this medium without this cation. Methylparathion degradation was observed at all the pHs studied and was independent of the predominant chemical form of Fe(III) in the aqueous medium. The reaction was first-order with pH-dependent rate constant (k) values ranging from 3.3 x 10(- 3) h(- 1) to 7.0 x 10(- 3) h(- 1). The k values increased as pH decreased, suggesting that Fe(III) acted as an electrophile in the reaction mechanism.     

Fate of a stilbene-type fluorescent whitening agent (DSBP) in the presence of Fe(III) aquacomplexes: from the redox process to the photodegradation

The behaviour of 4,4′-bis(2-sulfostyryl)biphenyl (DSBP), a fluorescent whitening agent, was investigated in the presence of Fe(III) aquacomplexes at room temperature. In the dark, a two-step reaction was observed when adding Fe(III) to a solution of DSBP: an initial fast redox reaction between DSBP and the monomeric species Fe(OH)²⁺ and a slower reaction leading to the coagulation of oxidised DSBP and iron. This phenomenon is due to the formation of a complex or an ion-pair between Fe(II) and/or Fe(III) with oxidised DSBP and it probably occurs by charge neutralisation in our experimental conditions. The precipitation of DSBP depends on the initial concentration in Fe(OH)²⁺ and is achieved for a ratio [Fe(OH) ²⁺]/[DSBP] of 5 approximately. Under irradiation at 365 nm, a complicated behaviour was observed: a complexation of iron by oxidised DSBP favoured by irradiation and a degradation of DSBP induced by an intramolecular electron transfer in the complex or by a photoredox of Fe(OH)²⁺ species generating OH radicals in the supernatant. The complete degradation of DSBP is reached four times faster in the presence of Fe(III) with respect to the direct photolysis of DSBP alone. Moreover, the total mineralization of DSBP obtained in less than 120 h upon irradiation at 365 nm is only observed in the presence of the ferric ions, enlightening the efficiency of the method involving Fe(III) and UV irradiation.     

An improved UV/Fe3+ process by combination with electrocatalysis for p-nitrophenol degradation

p-nitrophenol (PNP) was investigated as a model pollutant under the improved UV/Fe3+ process by combination with electrocatalysis. In the individual UV/Fe3+ process, PNP degradation rate was dependent on Fe(III) concentration and decreased during degradation due to the depletion of ferric ion and thus it was very difficult to reach the quick mineralization of organics. These drawbacks could be significantly overcome in the modified UV/Fe3+ process, and synergetic effects for PNP and COD removal were observed at two investigated Fe(III) concentrations. The enhancements on the degree of conversion for PNP and COD in presence of 0.5 mM Fe(III) were 184% and 242%, respectively, and PNP of initial concentration of 1.0 mM could be completely removed within 1 h. Thus such a process would be very attractive to the rapid mineralization of the biorefractory compounds for wastewater treatment. The possible reasons for the synergetic effects were the electrochemical regeneration of ferric ion and the role of the oxygen that formed on the anode. Based on degradation intermediates identification and synergetic effect probe, a general reaction pathway for PNP degradation in the improved process was proposed.     

Aniline degradation by Electro-Fenton and peroxi-coagulation processes using a flow reactor for wastewater treatment

The degradation of 10-30 l of a 1000 ppm aniline solution in 0.050 M Na2SO4 + H2SO4 at pH 3.0 and 40 degrees C by Electro-Fenton and peroxi-coagulation processes at constant current until 20 A has been studied using a pilot flow reactor in recirculation mode with a filter-press cell containing an anode and an oxygen diffusion cathode, both of 100 cm2 area. H2O2 is produced by the two-electron reduction of O2 at the cathode, being accumulated with a current efficiency between 60% and 80% at the first stages of electrolyses performed with a Ti/Pt anode. In the presence of 1 mM Fe2+, less H2O2 is accumulated, but it is not detected using an Fe anode. The Electro-Fenton process with 1 mM Fe2+ and a Ti/Pt or DSA anode yields an insoluble violet polymer, while the soluble total organic carbon (TOC) is gradually removed, reaching 61% degradation after 2 h at 20 A. In this treatment, pollutants are preferentially oxidized by hydroxyl radicals formed in solution from reaction of Fe2+ with H2O2. The peroxi-coagulation process with an Fe anode has higher degradation power, allowing to remove more than 95% of pollutants at 20 A, since some intermediates coagulate with the Fe(OH)3 precipitate formed. Both advanced electrochemical oxidation processes (AEOPs) show moderate energy costs, which increase with increasing electrolysis time and applied current.     

Homogeneous degradation of 1,2,9,10-tetrachlorodecane in aqueous solutions using hydrogen peroxide, iron and UV light

The homogeneous degradation of the polychlorinated n-alkane, 1,2,9,10-tetrachlorodecane (T4C10), was studied in aqueous solutions of hydrogen peroxide, including Fenton and photo-Fenton reaction conditions. All solutions were adjusted to a pH of 2.8 and an ionic strength of 0.1 M NaClO4 prior to photolysis. T4C10 (2 x 10(-6) M) was substantially degraded by the H2O2/UV system (1.0 x 10(-2) M H2O2), with 60% disappearance in 20 min of irradiation in a photoreactor equipped with 300 nm lamps of light intensity 3.6 x 10(-5) Ein L(-1) min(-1) (established by ferrioxalate actinometry). The reaction produced stoichiometric amounts of chloride ion indicating complete dechlorination of the chlorinated n-alkane. T4C10 degraded very slowly under Fenton (Fe2+/H2O2/dark) and Fenton-like (Fe3+/H2O2/dark) conditions. However, when the same solutions were irradiated, T4C10 degraded more rapidly than in the H2O2/UV system, with 61% disappearance in 10 min of exposure. The rapid degradation is related to the enhanced degradation of hydrogen peroxide to oxidizing *OH radicals under photo-Fenton conditions. Degradation was inhibited in both the H2O2/UV and photo-Fenton systems by the addition of KI and tert-butyl alcohol due to *OH scavenging.     

Photo-Fenton degradation of dichloromethane for gas phase treatment

A continuous photo-Fenton process has been used for the degradation of gaseous dichloromethane (DCM). By absorbing gaseous DCM into a reactive Fenton mixture, the scrubbing and degradation processes could be completed in the one reactor. Operating with a Dark Fenton solution did not result in removal of DCM any better than simply using MilliQ water. This was because the Fe(II) quickly converted to Fe(III) but was unable to regenerate. After a short time, the Fenton process was no longer operating and the DCM quickly accumulated in the reaction solution, preventing further accumulation due to a decreasing concentration gradient in the reactive solution. However, by using UV light and increasing the retention time from 20 to 50 s, there was sufficient time for the reactive solution to regenerate and continuous operation could achieve at least 65% removal of DCM from the gaseous phase at ambient temperature.     

Degradation of the pharmaceutical metronidazole via UV, Fenton and photo-Fenton processes

Degradation rates and removal efficiencies of Metronidazole using UV, UV/H2O2, H2O2/Fe2+, and UV/H2O2/Fe2+ were studied in de-ionized water. The four different oxidation processes were compared for the removal kinetics of the antimicrobial pharmaceutical Metronidazole. It was found that the degradation of Metronidazole by UV and UV/H2O2 exhibited pseudo-first order reaction kinetics. By applying H2O2/Fe2+, and UV/H2O2/Fe2+ the degradation kinetics followed a second order behavior. The quantum yields for direct photolysis, measured at 254 nm and 200-400 nm, were 0.0033 and 0.0080 mol E(-1), respectively. Increasing the concentrations of hydrogen peroxide promoted the oxidation rate by UV/ H2O2. Adding more ferrous ions enhanced the oxidation rate for the H2O2/Fe2+ and UV/H2O2/Fe2+ processes. The major advantages and disadvantages of each process and the complexity of comparing the various advanced oxidation processes on an equal basis are discussed.     

Comparative study of the oxidation of atrazine and acetone by H2O2/UV, Fe(III)/UV, Fe(iii)/H2O2/UV and Fe(II) or Fe(III)/H2O2

In this study, the rates of degradation of organic compounds by several AOPs (H₂O₂/UV, Fe(III)/UV, Fe(III)/H₂O₂/UV, Fe(II)/H₂O₂ and Fe(III)/H₂O₂) have been compared. Experiments were carried out at pH ≈ 3 (perchloric acid / sodium perchlorate solutions) and with UV reactors equipped with a low-pressure mercury vapour lamp (emission at 253.7 run). The data obtained with atrazine ([Atrazine]_o = 100 μg/L) showed that the rate of degradation of atrazine in very dilute aqueous solution is much more rapid with Fe(III)/UV than with H₂O₂/UV. Photo-Fenton process (Fe(III)/H₂O₂/UV) was found to be more efficient than H₂O₂/UV and Fe(II)/H₂O₂ for the mineralization of acetone ([Acetone]_o = 1 mM).     

Photodegradation of alachlor with the TiO(2) film immobilised on the glass tube in aqueous solution

Alachlor photodegradation was performed using TiO(2), which was synthesized by a modified sol-gel method. The thickness of a TiO(2) film immobilised by a 5-time dip-coating was 174 nm and the average diameter of TiO(2) particles was about 10-15 nm in SEM images. The crystal structure of a TiO(2) film calcinated at 300 degrees C for 1 h was observed as a typical anatase type. The stability of a TiO(2) film by a modified sol-gel method was 4% better than TiO(2) by a typical sol-gel method.The removal rate of alachlor with both Fe(3+) and UV radiation in the absence of TiO(2) was 0.28 mg/l/h in 10 h and the removal rate of alachlor with Fe(3+)/UV in the presence of TiO(2) was 0.32 g/l/h, which was higher by 14% than that with Fe(3+)/UV system. TOC concentration during the alachlor degradation with both TiO(2) and UV radiation in the absence of added Fe(3+) decreased from 100%, through 81% and 51%, to 44% with time elapses of 4, 8, and 10 h, respectively, while TOC concentration with both added Fe(3+) and UV radiation in the absence of TiO(2) decreased from 100% to 70% in 10 h.     

Temperature dependence of hydroxyl radical formation in the hv/Fe3+/H2O2 and Fe3+/H2O2 systems

The thermal enhancement of the formation of *OH by the hv/Fe(III)/H2O2 system (including the Fe(III)/H2O2 system) was quantitatively investigated with reaction temperatures ranging from 25 to 50 degrees C. A temperature dependent kinetic model for the hv/Fe(III)/H2O2 system, incorporating 12 major reactions with no fitted rate constants or activation energies, was developed, and successfully explained the experimental measurements. Particularly, the thermal enhancement of Fe(OH)2+ photolysis which is the most significant step in the hv/Fe(III)/H2O2 system was effectively explained by two factors; (1) the variation of the Fe(OH)2+ concentration with temperature, and (2) the temperature dependence of the quantum yield for Fe(OH)2+ photolysis (measured activation energy=11.4 kJ mol(-1)). Although in both the hv/Fe(III)/H2O2 and Fe(III)/H2O2 systems, elevated temperatures enhanced the formation of *OH, the thermal enhancement was much higher in the dark Fe(III)/H2O2 system than the hv/Fe(III)/H2O2 system. Furthermore, it was found that the relative thermal enhancement of the formation of *OH in the presence of *OH scavengers (tert-butyl alcohol) was magnified in the Fe(III)/H2O2 system but was not in the hv/Fe(III)/H2O2 system.     

TiO2-catalyzed photooxidation of arsenite to arsenate in aqueous samples

The TiO2-catalyzed photooxidation of arsenite (As(III)) to arsenate (As(V)) was studied in aqueous TiO2 suspensions using a solar simulator which emitted ultraviolet and visible radiations. The concentration of As(III) was varied between 50 microg l(-1) and 10 mg l(-1), and the concentration of TiO2 between 1 mg l(-1) and 50 mg l(-1). Total oxidation of As(III) to As(V) occurred within minutes. The concentration of As(III) declined exponentially which indicates first-order kinetics. In the pH range between 5 and 9 there was no significant influence of the pH of the suspension on the reaction rate. Batch experiments without irradiation showed that part of the arsenic was adsorbed on the TiO2 surface. When using 100 microg l(-1) As and between 1 mg l(-1) and 50 mg l(-1) TiO2, 8-39% of As(III) and up to 73% of As(V) were adsorbed by TiO2. As(III) was also oxidized by UV radiation in the absence of TiO2, but the reaction was slower than in the presence of TiO2 resulting in an irradiation time too long for practical use. In addition, oxidation of As(III) in the presence of TiO2 was also observed under solar irradiation within a few minutes.     

Ferrioxalate-mediated photodegradation and mineralization of 4-Chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Advanced oxidation processes are powerful methods which are capable of transforming refractory, nonbiodegradable and/or toxic organic compounds into harmless end products such as carbon dioxide and water. However, one commen problem of all advanced oxidation processes is the high demand of electrical energy for ultraviolet lamps, which causes high operational costs. Minimization of the required irradiation time, and therefore the energy consumption, by optimization of other reaction conditions such as catalyst-oxidant type and concentration, pH, temperature, pollutant/oxidant ratio etc., therefore continues to gain importance. OBJECTIVE: The main objective of this study was the minimization of the required irradiation time through optimization of the use of a newly patented catalyst, ferrioxalate, and also to compare the performance of this catalyst with the performance of other AOPs. METHODS: Oxidation of 4-chlorophenol by photo-Fenton process using potassium ferrioxalate as a mediator was studied in a lab scale photoreactor. The influence of parameters such as hydrogen peroxide and ferrioxalate concentrations, initial pH, power-output, oxalate/iron ratio and different iron sources was evaluated. An upflow photoreactor equipped with a 1000 Watt high-pressure mercury vapour lamp and operating in a recirculation mode was used during photodegradation experiments. The extent of the reduction of 4-chlorophenol, Total Organic Carbon and Chemical Oxygen Demand was used to evaluate the photodegradation reaction. RESULTS AND DISCUSSION: The optimum pH range observed was found to be 2.7-3. The efficiency of 4-chlorophenol oxidation increased with increasing concentrations of hydrogen peroxide and ferrioxalate, reaching a plateau after the addition of 10 and 0.072 mM of those reagents, respectively. Using an Oxalate/iron ratio of 12 was 18% less efficient than using a ratio of 3:1. The efficiency increased with increasing radiation power. However, this increase was not linear. The UV/ferrioxalate/H2O2 process, by which complete mineralization of 100 mg l(-1) 4-chlorophenol was achieved in 20 min of total reaction time, was the most efficient process among the alternatives applied. CONCLUSIONS: The use of ferrioxalate as the catalyst was found to be more efficient than the use of Fe(II) and Fe(III) iron species. It was possible to completely mineralize 4-chlorophenol. RECOMMENDATION AND OUTLOOK: The results of this study demonstrate that the ferrioxalate-mediated degradation of 4-chlorophenol requires less irradiation times than other advanced oxidation processes. There are mainly 19 phenol isomers and other toxic and nonbiodegradable organic compounds. We recommend that similar studies should be performed on many such compounds in order to attain a clear understanding of the performance of this catalyst. Because of its light sensitivity, this catalyst should be used immediately after its preparation. The use of low pressure mercury vapour lamps in this process should also be considered, since low power outputs may be enough for the process.     

Photodegradation of 4-tert octylphenol in aqueous solution promoted by Fe(III)

4-Tert-octylphenol (4-t-OP), a kind of endocrine-disrupting compounds, is widely distributed in natural water surroundings but can hardly be biodegraded. The advanced oxidation processes (AOPs) have been proved to be an efficient method to degrade 4-t-OP. In this study, the photodegradation of 4-t-OP in aqueous solution promoted by Fe(III) and the photooxidation mechanism were investigated. The ferric perchlorate was added into the aqueous solution for the production of hydroxyl radical. The efficiency of mineralization was monitored by total organic carbon analyzer, and photooxidation products were determined by high-performance liquid chromatography and liquid chromatography-mass spectrometer. 4-t-OP (2.4?×?10^?5 M) in aqueous solution was completely degraded after 45 min in the presence of Fe(III) (1.2?×?10^?3 M) under UV irradiation (λ?=?365 nm). The optimal pH was 3.5. Higher Fe(III) concentration or lower initial 4-t-OP concentration led to increased photodegradation efficiency of 4-t-OP. The reaction was almost completely inhibited in the presence of 2-propanol. About 70 % mineralization of the solution was obtained after 50 h. The photooxidation product was supposed to be 4-tert-octyl catechol. 4-t-OP in aqueous solution can be degraded in the presence of Fe(III) under the solar irradiation. The photoinduced degradation is due to the reaction with hydroxyl radicals. It shows that the 4-t-OP is mineralized by the inducement of Fe(III) aquacomplexes, which exposes to solar light. Therefore, the results would provide useful information for the potential application of the AOPs to remove 4-t-OP in water surroundings.     

Kinetics of oxidation of chlorobenzenes and phenyl-ureas by Fe(II)/H2O2 and Fe(III)/H2O2. Evidence of reduction and oxidation reactions of intermediates by Fe(II) or Fe(III)

The rates of degradation of 1,2,4-trichlorobenzene (TCB), 2,5-dichloronitrobenzene (DCNB), diuron and isoproturon by Fe(II)/H2O2 and Fe(III)/H2O2 have been investigated in dilute aqueous solution ([Organic compound]0 approximately 1 microM, at 25.0 +/- 0.2 degrees C and pH < or = 3). Using the relative rate method with atrazine as the reference compound, and the Fe(II)/H2O2 (with an excess of Fe(II)) and Fe(III)/H2O2 systems as sources of OH radicals, the rate constants for the reaction of OH* with TCB and DCNB were determined as (6.0 +/- 0.3)10(9) and (1.1 +/- 0.2)10(9) M(-1) s(-1). Relative rates of degradation of diuron and isoproturon by Fe(II)/H2O2 were about two times smaller in the absence of dissolved oxygen than in the presence of oxygen. These data indicate that radical intermediates are reduced back to the parent compound by Fe(II) in the absence of oxygen. Oxidation experiments with Fe(III)/H2O2 showed that the rate of decomposition of atrazine markedly increased in the presence of TCB and this increase has been attributed to a regeneration of Fe(II) by oxidation reactions of intermediates (radical species and dihydroxybenzenes) by Fe(III).     

Kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE)

The kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE) in aqueous solutions at various pH, temperature, oxidant concentration and ionic strength levels was studied. The MTBE degradation was found to follow a pseudo-first-order decay model. The pseudo-first-order rate constants of MTBE degradation by persulfate (31.5 mM) at pH 7.0 and ionic strength 0.11 M are approximately 0.13 x 10(-4), 0.48 x 10(-4), 2.4 x 10(-4) and 5.8 x 10(-4) S(-1) at 20, 30, 40 and 50 degrees C, respectively. Under the above reaction conditions, the reaction has an activation energy of 24.5 +/- 1.6 kcal/ mol and is influenced by temperature, oxidant concentration, pH and ionic strength. Raising the reaction temperature and persulfate concentration may significantly accelerate the MTBE degradation. However, increasing both pH (over the range of 2.5-11) and ionic strength (over the range of 0.11-0.53 M) will decrease the reaction rate. Reaction intermediates including tert-butyl formate, tert-butyl alcohol, acetone and methyl acetate were observed. These intermediate compounds were also degraded by persulfate under the experimental conditions. Additionally, MTBE degradation by persulfate in a groundwater was much slower than in phosphate-buffer solutions, most likely due to the presence of bicarbonate ions (radical scavengers) in the groundwater.     

Oxidation of TNT by photo-Fenton process

A series of photo-Fenton reactions have been performed for the degradation of 2,4,6-trinitrotoluene (TNT) in a 4.2-l reactor. The degradation reaction rate of TNT followed a pseudo-first-order behavior; and the rate constants for 2.4mW cm(-2)UV only, 2.4mW cm(-2)UV/H(2)O(2), Fenton, photo-Fenton (2.4mW cm(-2)) and photo-Fenton (4.7mW cm(-2)) were 0.002min(-1), 0.007min(-1), 0.014min(-1), 0.025min(-1) and 0.037min(-1), respectively. Increasing the intensity of UV light, and the concentrations of ferrous ions and hydrogen peroxide promoted the oxidation rate under the experimental conditions in this study. The weighting factor (f), the Fe(II)-promoted efficiency (r) and the promoted-UV light efficiency (p) were calculated to clarify their effects on the TNT oxidation. Moreover, the inhibition effect of hydroxyl radical was also observed in both Fenton and photo-Fenton oxidation when the concentration of Fe(II) were higher than 2.88mM. Solid phase micro-extraction was first applied to the separation of the organic byproducts from TNT oxidation. GC/MS was employed to identify the byproducts during the Fenton and photo-Fenton oxidation of TNT. These compounds were clarified as 1,3,5-trinitrobenzene, 1-methyl-2,4-dinitrobenzene 2,5-dinitrobenzoic acid and 1,3-dinitrobenzene. By these byproducts, the mechanisms of the methyl group oxidation, decarboxylation, aromatic ring breakage, and hydrolysis can be recognized and demonstrated. The pathway of TNT oxidation by photo-Fenton process was also proposed in this study.     

Photochemical degradation and mineralization of 4-chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Since the intermediate products of some compounds can be more toxic and/or refractory than the original compund itself, the development of innovative oxidation technologies which are capable of transforming such compounds into harmless end products, is gaining more importance every day. Advanced oxidation processes are one of these technologies. However, it is necessary to optimize the reaction conditions for these technologies in order to be cost-effective. OBJECTIVE: The main objectives of this study were to see if complete mineralization of 4-chlorophenol with AOPs was possible using low pressure mercury vapour lamps, to make a comparison of different AOPs, to observe the effect of the existence of other ions on degradation efficiency and to optimize reaction conditions. METHODS: In this study, photochemical advanced oxidation processes (AOPs) utilizing the combinations of UV, UV/H2O2 and UV/H2O2/Fe2+ (photo-Fenton process) were investigated in labscale experiments for the degradation and mineralization of 4-chlorophenol. Evaluations were based on the reduction of 4-chlorophenol and total organic carbon. The major parameters investigated were the initial 4-chlorophenol concentration, pH, hydrogen peroxide and iron doses and the effect of the presence of radical scavengers. RESULTS AND DISCUSSION: It was observed that the 4-chlorophenol degradation efficiency decreased with increasing concentration and was independent of the initial solution pH in the UV process. 4-chlorophenol oxidation efficiency for an initial concentration of 100 mgl(-1) was around 89% after 300 min of irradiation in the UV process and no mineralization was achieved. The efficiency increased to > 99% with the UV/H2O2 process in 60 min of irradiation, although mineralization efficiency was still around 75% after 300 min of reaction time. Although the H2O2/4-CP molar ratio was kept constant, increasing initial 4-chlorophenol concentration decreased the treatment efficiency. It was observed that basic pHs were favourable in the UV/H2O2 process. The results showed that the photo-Fenton process was the most effective treatment process under acidic conditions. Complete disappearance of 100 mgl(-1) of 4-chlorophenol was achieved in 2.5 min and almost complete mineralization (96%) was also possible after only 45 min of irradiation. The efficiency was negatively affected from H2O2 in the UV/H2O2 process and Fe2+ in the photo-Fenton process over a certain concentration. The highest negative effect was observed with solutions containing PO4 triple ions. Required reaction times for complete disappearance of 100 mgl(-1) 4-chlorophenol increased from 2.5 min for an ion-free solution to 30 min for solutions containing 100 mgl(-1) PO4 triple ion and from 45 min to more than 240 min for complete mineralization. The photodegradation of 4-chlorophenol was found to follow the first-order law. CONCLUSION: The results of this study showed that UV irradiation alone can degrade 4-CP, although at very slow rates, but cannot mineralize the compound. The addition of hydrogen peroxide to the system, the so-called UV/H2O2 process, significantly enhances the 4-CP degradation rate, but still requires relatively long reaction periods for complete mineralization. The photo-Fenton process, the combination of homogeneous systems of UV/H2O2/Fe2+ compounds, produces the highest photochemical elimination rate of 4-CP and complete mineralization is possible to achieve in quite shorter reaction periods when compared with the UV/H2O2 process. RECOMMENDATIONS AND OUTLOOK: It is more cost effective to use these processes for only purposes such as toxicity reduction, enhancement of biodegradability, decolorization and micropollutant removal. However the most important point is the optimization of the reaction conditions for the process of concern. In such a case, AOPs can be used in combination with a biological treatment systems as a pre- or post treatment unit providing the cheapest treatment option. The AOP applied, for instance, can be used for toxicity reduction and the biological unit for chemical oxygen demand (COD) removal.     

Fe(III)-oxalate complexes induced photooxidation of diethylstilbestrol in water

In this work, the photooxidation of diethylstilbestrol (DES), a synthetic estrogen, was investigated in a concentric reactor under a 125 W high-pressure mercury lamp (lambda > or = 365 nm). The photooxidation efficiencies were dependent on the pH values and Fe(III)/oxalate ratios of the system, with higher efficiency at pH 3.50+/-0.05 and Fe(III)/oxalate ratio 10.0/120.0 micromol l(-1). The photooxidation reactions obeyed the law of pseudo-first-order reaction at the concentration over the range of 2.0-10.0 mg l(-1) of DES. The photooxidation rates decreased with increasing the initial concentrations of DES. For 2.0 mg l(-1) DES, the observed photooxidation rate coefficient (k(obs)) was 0.00622 min(-1). By using GC-MS and LC-MS techniques, the predominant photooxidation products DES-o-catechol ([M](+), m/z 284) and DES-4-semiquinone ([M](-), m/z 267) were respectively identified and the mechanisms for the oxidative degradation were proposed. When DES reacted with OH radicals, C atoms in 3-position were added with OH radicals to produce hydrolyzed DES radical followed by two oxidation pathways: (1) dehydrolyzing to produce DES-4-semiquinone which was oxidized further to DES-4,4'-quinone; (2) undergoing peroxidation by O(2) and getting rid of HO(2) radical to produce DES-o-catechol. After that, the two H atoms on the hydroxy group of the catechol were extracted in two individual steps to form intermediates semiquinone radical and o-quinone. The catechol intermediates underwent further oxidation, benzene ring cleavage and decarboxylation, up to mineralization ultimately.