Bioremediation of Dissolved and Free Phase Oil in Wastewater from Equipment Maintenance Activities

Land treatment facilities can provide effective treatment of secondary oily wastewater from maintenance operations, particularly in arid climates. Soil and underlying groundwater from a land treatment facility, which has been operating for eight years, were analyzed to determine the effectiveness of using bioremediation for the treatment of dissolved and free‐phase oil in maintenance wastewater. The study was conducted at a mining site in Western Australia. The facility was capable of treating 140 kiloliters (kL) of oily wastewater per day. The average petroleum hydrocarbon content of the wastewater was 2 percent weight per volume (w/v) based on data available for the first five years. The soil data indicate that the land treatment process has been operating efficiently even at high wastewater loadings with maximum degradation rates of 10–242 mg/kg per day. Based on the soil data, there is no evidence of accumulation of any metal or polycyclic aromatic hydrocarbon (PAH) compounds. The land treatment facility has led to only low levels of TPH (total petroleum hydrocarbons) contamination (<4 ppm) in the underlying groundwater. However, nitrate concentrations in the groundwater were shown to increase over the first five years of the facility's operation. This article reports and discusses the operational data from the land treatment process, illustrating its effectiveness in treating oily wastewater. © 2001 John Wiley & Sons, Inc.     

Oil/Suspended Particulate Material Interactions and Sedimentation

The interactions of physically dispersed oil droplets with suspended particulate material (SPM) can be important for the transport of bulk quantities of spilled crude oil and polycyclic aromatic hydrocarbons (PAH) to subtidal sediments. The literature regarding oil/SPM interactions is reviewed, and results from whole-oil droplet/SPM interaction kinetics and pure-component (Prudhoe Bay crude oil distillate cut) equilibrium partitioning experiments are presented. The effects of oil type, SPM characteristics, and salinity on the interaction rates are examined, and the importance of whole-oil droplet/SPM interactions on particle agglomeration and settling behavior are discussed. Whole-oil droplet/SPM interactions are retarded as oil droplet dispersion into the water column is inhibited by oil viscosity increases due to evaporation weathering and water-in-oil emulsification. Compared to whole oil droplet/SPM interactions, dissolved-component/SPM adsorption is not as significant for transport of individual components to sediments. The information presented in this paper can be used to augment computer-based models designed to predict oil-spill trajectories, oil-weathering behavior, and spilled oil impacts to the marine environment.     

Application of Ultraviolet Fluorescence Spectroscopy to Monitor Oil–Mineral Aggregate Formation

At an excitation wavelength of 320 nm, the ultraviolet fluorescence (UVF) spectra emitted by reference oils dispersed in seawater with mineral fines yielded two important results:

• (1)Resuspended negatively-buoyant oil–mineral aggregates (OMAs) exhibited maximum fluorescence at an emission wavelength of 450 nm and,
• (2)the hydrocarbons dispersed and/or dissolved in the seawater that remained after the aggregates had settled out exhibited maximum fluorescence at 355 nm.

Data from UVF analysis (450 nm emission) and microscopical observations of seven reference oils suggest that higher-viscosity oils are less likely to form aggregates with mineral fines. This decline in OMA formation with increased oil viscosity could be predicted from a decrease in the ratio of emission at 450–355 nm. The data suggest that direct UVF spectroscopy of dispersed/dissolved oil and OMAs in seawater can be used to predict and verify the extent of OMA formation.     

Groundwater Impacts on Surface Water and Sediment—Gowanus Canal,Brooklyn, New York

The Gowanus Canal Superfund Site in Brooklyn, New York, is an approximately 1.5‐mile (1.61‐km) long estuary that was historically converted into a canal for industrial and commercial purposes. Three manufactured gas plants (MGPs) were formerly located on the Gowanus Canal and discharged waste into it. Surface sediments remain highly contaminated with polycyclic aromatic hydrocarbons (PAHs) long after the MGPs were razed. A hydrogeologic assessment indicates that groundwater passes through the deeper coal tar–contaminated sediment prior to discharging to the canal. This study was undertaken to investigate if groundwater passing through coal tar–contaminated sediment could be responsible for the ongoing contamination of both surface sediments and surface water in the canal. PAH compound distributions in surface water samples collected from the tidal canal at low tide were compared with PAH compounds found in adjacent groundwater‐monitoring wells, point sources (combined sewer overflows [CSOs]), and surface sediments. The results indicate a strong correlation between PAH contaminant distributions in groundwater, sediment, and surface water, indicating that contaminated groundwater passing through the deeper coal tar–contaminated sediments is the primary mechanism contributing to the contamination of both surface sediment and surface water in the canal. Therefore, any sediment remediation efforts in the Gowanus Canal that fail to evaluate and control the upward transport processes have a high chance of failure due to recontamination from below.  ©2016 Wiley Periodicals, Inc.     

Pseudomonas sp. (Strain 10–1B): A potential inoculum candidate for green and sustainable remediation

Soil pollution caused by polycyclic aromatic hydrocarbons (PAHs) is a consequence of various industrial processes which destabilizes the ecosystem. Bioremediation by bacteria is a cost‐effective and environmentally safe solution for reducing or eliminating pollutants in soils. In the present study, we artificially polluted agricultural soil with used automobile engine oil with a high PAH content and then isolated bacteria from the soil after 10 weeks. Pseudomonas sp. strain 10–1B was isolated from the bacterial community that endured this artificial pollution. We sequenced its genomic DNA on Illumina MiSeq sequencer and evaluated its ability to solubilize phosphate, fix atmospheric nitrogen, and produce indoleacetic acid, in vitro, to ascertain its potential for contribution to soil fertility. Its genome annotation predicted several dioxygenases, reductases, ferredoxin, and Rieske proteins important in the ring hydroxylation initiating PAH degradation. The strain was positive for the soil fertility attributes evaluated. Such combination of attributes is important for any potential bacterium partaking in sustainable bioremediation of PAH‐polluted soil.     

Oil-Mineral Aggregate Formation on Oiled Beaches: Natural Attenuation and Sediment Relocation

The significance of oil-mineral aggregate (OMA) formation on the effectiveness of the in situ shoreline treatment options of natural attenuation (natural recovery) and sediment relocation (surf washing) was examined during field trials on two mixed-sediment (sand and pebble) beaches experimentally oiled with IF-30 oil. At both sites, the amount of oil remaining in the experimental plots was dramatically reduced within five days after sediment relocation treatments. Time-series microscopy and image analysis of breaker-zone water samples demonstrate that OMA formation occurred naturally on the oiled beaches at both sites and was accelerated by the sediment relocation procedure. Lower concentrations of OMA in the breaker zone at Site 3 are attributed to the higher wave-energy levels at this site that presumably facilitated more rapid OMA dispersion. The granulometry and mineralogy of beach sediment and of subtidal sediment trap samples indicate that the material settling in nearshore waters originated from the relocated sediment and that a portion of the finer sediment was probably transported out of the study region before settling. Gas chromatography/mass spectrometry analysis demonstrated that a significant fraction of the oil dispersed into nearshore waters and sediments by interaction with mineral fines was biodegraded. The fact that little or no residual oil was found stranded on the shore in areas adjacent to the experimental plots and that only small amounts of oil were found in nearshore subtidal sediments and sediment trap samples suggests that a large fraction of the oil lost from the experimental plots may have been dispersed in the form of relatively buoyant OMA.     

Contaminant mass flux and forensic assessment of polycyclic aromatic hydrocarbons: Tools to inform remediation decision making at a contaminated site in Canada

Polycyclic aromatic hydrocarbons (PAHs) and metal(loid) mass flux estimates and forensic assessment using PAH diagnostic ratios were used to inform remediation decision making at the Sydney Tar Ponds (STPs) and Coke Ovens cleanup project in eastern Canada. Environmental effects monitoring of surface marine sediments in Sydney Harbor indicated significantly higher PAH concentrations during the first year of remediation monitoring compared to baseline. This was equivalent to PAH loadings of ～2,000 kg over a 15‐month period. Increases in sediment PAH concentrations raised serious concerns for regulators, who requested cessation of remediation activities early in the $400 M (CAD) project. Historically, the STPs were reported as the primary source of PAH contamination in Sydney Harbor with estimated discharges of 300 to 800 kg/year between 1989 and 2001. Mass flux estimates of PAHs and metal(loid)s and PAH diagnostic ratios were used to evaluate if increases in PAH concentrations in marine sediments were the result of the STPs remediation activities. PAH mass flux estimates approximated that 17 to 97 kg/year were discharged from the STPs during three years of remediation and were corroborated by an independent PAH flux estimate of 119 kg in year 1. PAH fluxes to the Sydney Harbor were mostly surface water derived, with groundwater contributing negligible quantities (0.002–0.005 kg/year). Fluxes of metal(loid)s to harbor sediments were stable or declining across all years and were mirrored in sediment metal(loid) concentrations, which lacked temporal variation, unlike total PAH concentrations. Flux results were also corroborated using PAH diagnostic ratios, which found a common source of PAHs. Coal combustion was likely the principal source of PAHs and not migration from the STPs during remediation. Although short‐term residual sediment PAH increases during onset of remediation raised concerns for regulators, calls for premature cessation of remediation early in the project were unwarranted based on only one year of monitoring data. Mass flux estimates and forensic assessments using PAH diagnostic ratios proved useful tools to inform remediation decision making that helped environmental protection and reduced costs associated with lost cleanup time.     

A comparison of mesophilic composting and unamended land treatment for the bioremediation of aged tar residues in soil

A field study was conducted to compare the effectiveness of land treatment and mesophilic composting in removing aged polycyclic aromatic hydrocarbons (PAH) from soil. The soil composting treatment, which had 20 percent (w/w) fresh organic matter incorporated into the soil, reached mesophilic temperatures of 45 to 50°C at week 3–4 and was effective in reducing PAH from 2240 mg/kg to 120 mg/kg after 224 days of treatment. Conventional land treatment with and without added cow manure (5 percent w/w) was less effective in removing the PAH from the soil than was the mesophilic soil composting treatment. In a parallel laboratory trial, PAH concentrations were reduced below 500 mg/kg (the target cleanup concentration for the site) when the contaminated soil was amended with 20 to 30 percent (w/w) fresh organic matter after 186 days of treatment. PAH degradation was lower in the laboratory trial compared with the field trial and no self-heating of soil was demonstrated in the laboratory. Based on the relatively high total heterotrophic and naphthalene-degrading microbial populations in the nonsterile treatments, it was apparent that the absence of microorganisms was unlikely to have limited the biodegradation of PAH in the current study. Fresh organic matter amendments of green tree waste and cow manure, regular mixing of the compost, and maintenance of moisture by regular watering were critical factors in achieving the target PAH concentrations.     

Toxicity Evaluation with the Microtox Test to Assess the Impact of In Situ Oiled Shoreline Treatment Options: Natural Attenuation and Sediment Relocation

Changes in the toxicity levels of beach sediment, nearshore water, and bottom sediment samples were monitored with the Microtox^® Test to evaluate the two in situ oil spill treatment options of natural attenuation (natural recovery--no treatment) and sediment relocation (surf washing). During a series of field trials, IF-30 fuel oil was intentionally sprayed onto the surface of three mixed sediment (pebble and sand) beaches on the island of Spitsbergen, Svalbard, Norway (78°56^′ N, 16°45^′ E). At a low wave-energy site (Site 1 with a 3-km wind fetch), where oil was stranded within the zone of normal wave action, residual oil concentrations and beach sediment toxicity levels were significantly reduced by both options in less than five days. At Site 3, a higher wave-energy site with a 40-km wind fetch, oil was intentionally stranded on the beach face in the upper intertidal/supratidal zones, above the level of normal wave activity. At this site under these experimental conditions, sediment relocation was effective in accelerating the removal of the oil from the sediments and reducing the Microtox^® Test toxicity response to background levels. In the untreated (natural attenuation) plot at this site, the fraction of residual oil remaining within the beach sediments after one year (70%) continued to generate a toxic response. Chemical and toxicological analyses of nearshore sediment and sediment-trap samples at both sites confirmed that oil and suspended mineral fines were effectively dispersed into the surrounding environment by the in situ treatments. In terms of secondary potential detrimental effects from the release of stranded oil from the beaches, the toxicity level (Microtox^® Test) of adjacent nearshore sediment samples did not exceed the Canadian regulatory limit for dredged spoils destined for ocean disposal.     

Optimization of the food waste water incineration with respect to CO and NO<Subscript>x</Subscript> emission characteristics

The incineration of food waste water in conjunction with the domestic waste is getting attention as a food waste water treatment method, due to its low treatment cost and high efficiency. Many studies verified that the ammonia in the food waste water served as a reducing agent to suppress the generation of NO_x when the food waste water was injected and incinerated. However, they have not revealed the correlation between the change in the concentration of the CO and NO_x by the influence of the solid matters contained in the food waste water on the incineration of the wastes. The purpose of this study is to determine the optimum amount of the food waste water injected through four nozzles in the primary and secondary incineration chambers and to assess the correlation between the concentration of CO and NO_x in accordance with the food waste water injection in each chamber of the incinerator. For the study, four food waste water injection nozzles were installed; two (A and B) at the top of the primary incineration chamber and the other two (C and D) in the secondary incineration chamber. The correlation between the change in the concentration of CO and NO_x was studied adjusting the amount of the food waste water injected through the nozzles. From the result, Case II showed the concentration of CO and NO_x as 1.8–10 and 14–26 ppm, respectively, while Case I showed that of CO and NO_x as 15–30 and 9–18 ppm, respectively. Those levels are well below the Korean emission criteria, 50 ppm for CO and 80 ppm for NO_x. Based on the results, it is evident there is a certain trade-off between emission of CO and NO_x, and Case II which has relatively low concentration of CO is easier and cheaper to control.     

Polycyclic aromatic hydrocarbon (PAH) emission from co-firing municipal solid waste (MSW) and coal in a fluidized bed incinerator

Polycyclic aromatic hydrocarbons (PAH) emissions from a commercial municipal solid waste incinerator (MSWI) were studied. A MSW–coal mixture and coal only were used as fuel for the fluidized bed incinerator. Seven sampling points were chosen according to the classified four PAH emission pathways: flue gas, residue, ash and water. The mixture of MSW and coal resulted in PAH emission more than that of coal only, and PAH emission increased with increasing MSW mass percentage. Calcium oxide (CaO) or calcium carbonate (CaCO₃) was added as a desulfurizer. PAH emission also changed with different desulfurizers because of their different influences on heat balance. The PAH toxic equivalent (TEQ) of all operating conditions was also examined, showing that total daily PAH emission from MSWI can be determined.     

TEMPO-Mediated Oxidation of Hemp Bast Holocellulose to Prepare Cellulose Nanofibrils Dispersed in Water

Hemp bast holocellulose fiber (Cannabis sativa L. Subsp. Sativa) was oxidized by TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical)-mediated oxidation at various NaClO addition levels in water at pH 10. When carboxylate contents of the oxidized products were 1.5–1.7 mmol/g, TEMPO-oxidized cellulose nanofibrils almost completely dispersed at the individual nanofibril were obtained by mechanical disintegration of the TEMPO-oxidized hemp bast holocelluloses in water, where the nanofibrillation yields were 98–100 %. The sugar composition analysis revealed that most of hemicelluloses originally present in the hemp bast holocellulose were degraded and removed from the solid oxidized products, providing almost pure TEMPO-oxidized celluloses. X-ray diffraction patterns of all TEMPO-oxidized hemp bast holocelluloses had the same cellulose I crystal structure and similar crystallinity indices and crystal widths, indicating that carboxylate groups formed by the oxidation were selectively present on the crystalline cellulose microfibril surfaces in the holocellulose. However, the weight recovery ratios and viscosity-average degrees of polymerization of the TEMPO-oxidized hemp bast holocelluloses decreased to 69–59 % and 470–380, respectively, when their carboxylate contents increased to 1.5–1.7 mmol/g by the TEMPO-mediated oxidation. Atomic force microscopy height images showed that the nanofibril widths were 2.7–2.9 nm, and the average nanofibril lengths decreased from 590 to 400 nm as the NaClO addition level was increased from 7.5 to 12.5 mmol/g in the TEMPO-mediated oxidation.     

Photo-oxidation and Photo-toxicity of Crude and Refined Oils

The fate and effects of an oil spill are effected by solar radiation through the action of photo-oxidation and photo-toxicity. Photo-oxidation, an important process in the weathering of oil, produces a variety of oxidized compounds, including aliphatic and aromatic ketones, aldehydes, carboxylic acids, fatty acids, esters, epoxides, sulfoxides, sulfones, phenols, anhydrides, quinones and aliphatic and aromatic alcohols. Some of these compounds contribute to the marine biota toxicity observed after an oil spill. Photo-toxicity occurs when uptake of certain petroleum compounds, e.g. certain polycyclic aromatic hydrocarbons and benzothiophenes, is followed by solar exposure which results in much greater toxicity than after dark uptake. The mechanism of PAH photo-toxicity includes absorbance of solar radiation by the PAH which produces a free radical and this free radical in turn reacts with oxygen to produce reactive oxygen species that can damage DNA and other cellular macromolecules. While most studies on photo-toxicity have been carried out in the laboratory, there are studies showing that water from an oil spill is photo-toxic to bivalve embryos for at least a few days after the spill. Other studies have found that oil contaminated sediments are photo-toxic to several marine invertebrates. More studies are required to determine if marine fauna at an oil spill site are effected by the action of photo-toxicity and photo-oxidation.     

Biodegradation of Dispersed Forties Crude and Alaskan North Slope Oils in Microcosms Under Simulated Marine Conditions

For oil spills in the open sea, operational experience has found that conventional response techniques, such as mechanical recovery, tend to remove only a small fraction of oil during major spills, a recent exception being the Mississippi River spill in Louisiana [Spill Sci. Technol. Bull. 7 (2002) 155]. By contrast, the use of dispersants can enable significant fractions of oil to be removed from the sea surface by dispersing the oil into the water column. It is thought that once dispersed the oil can biodegrade in the water column, although there is little information on the mechanism and rate of biodegradation. Two studies were undertaken on dispersion, microbial colonisation and biodegradation of Forties crude and Alaskan North Slope (ANS) oils under simulated marine conditions. The study using the Forties crude lasted 27 days and was carried out in conditions simulating estuarine and coastal conditions in waters around the UK (15 °C and in the presence of nutrients, 1 mg N-NO₃/l), while the ANS study simulated low temperature conditions typical of Prince William Sound (8 °C) and took place over 35 days. The results of both studies demonstrated microbial colonisation of oil droplets after 4 days, and the formation of neutrally buoyant clusters consisting of oil, bacteria, protozoa and nematodes. By day 16, the size of the clusters increased and they sank to the bottom of the microcosms, presumably because of a decrease in buoyancy due to oil biodegradation, however biodegradation of n-alkanes was confirmed only in the Forties study. No colonisation or biodegradation of oil was noted in the controls in which biological action was inhibited. Oil degrading bacteria proliferated in all biologically active microcosms. Without dispersant, the onset of colonisation was delayed, although microbial growth rates and population size in ANS were greater than observed with the Forties. This difference reflected the greater droplet number seen with ANS at 8 °C than with Forties crude at 15 °C. Although these studies differed by more than one variable, complicating comparison, the findings suggest that dispersion (natural or chemical) changes the impact of the oil on the marine environment, potentially having important implications for management of oil spills in relation to the policy of dispersant use in an oil spill event.     

Current status and challenges of remediating petroleum‐derived PAHs in soils: Nigeria as a case study for developing countries

Polycyclic aromatic hydrocarbons (PAHs) are among the world's most significant environmental organic contaminants because of their carcinogenic properties. PAHs are widely distributed globally as a result of releases from numerous natural and anthropogenic activities. Consequently, several PAH monitoring studies have been conducted and remediation approaches explored. This article aims to provide the current status of PAH distribution in Nigeria's oil and gas industrial region in relation to the technologies adopted for PAH remediation. Ideally, the findings will provide insight into the challenges in managing organic contaminants derived from petroleum exploration activities in developing countries with Nigeria as a case study.     

Characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil

An attempted has been made to recover high-calorific fuel gas and useful carbonaceous residue by the electric arc pyrolysis of waste lubricating oil. The characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil were investigated in this study. The produced gas was mainly composed of hydrogen (35–40%), acetylene (13–20%), ethylene (3–4%) and other hydrocarbons, whereas the concentration of CO was very low. Calorific values of gas ranged from 11,000 to 13,000 kcal kg^?1 and the concentrations of toxic gases, such as NO_x, HCl and HF, were below the regulatory emissions limit. Gas chromatography–mass spectrometry (GC/MS) analysis of liquid-phase residues showed that high molecular-weight hydrocarbons in waste lubricating oil were pyrolyzed into low molecular-weight hydrocarbons and hydrogen. Dehydrogenation was found to be the main pyrolysis mechanism due to the high reaction temperature induced by electric arc. The average particle size of soot as carbonaceous residue was about 10 μm. The carbon content and heavy metals in soot were above 60% and below 0.01 ppm, respectively. The utilization of soot as industrial material resources such as carbon black seems to be feasible after refining and grinding.     

Thermal desorption of PCB-contaminated waste at the waukegan harbor superfund site

In June 1992, SoilTech ATP Systems, Inc., completed the soil treatment phase of the Waukegan Harbor Superfund Project in Waukegan, Illinois, after approximately five months of operation. SoilTech successfully treated 12,700 tons of sediment contaminated with polychlorinated hiphenyls (PCBs) using a transportable SoilTech anaerobic thermal processor (ATP) system nominally rated at ten tons per hour throughput capacity. The SoilTech ATP technology anaerobically desorbs contaminants such as PCBs from solids and sludges at temperatures over 1,000° F. Principal products of the process are clean, treated solids and an oil condensate containing the hydrocarbon contaminants. At the Waukegan Harbor Superfund site, PCB concentrations in the sediments excavated and dredged from a ditch, lagoon, and harbor slip averaged 10,400 parts per million (ppm) (1.04 percent) and were as high as 23,000 ppm (2.3 percent). Treated soil was backfilled in an on-site containment cell. The removal efficiency of PCBs from the soil averaged 99.98 percent, relative to the project performance specification of 97 percent, and treated soil PCB concentrations were measured below 2 ppm. Approximately 30,000 gallons of PCB oil, desorbed from the feed material, were returned to the owner for subsequent off-site disposal. After modifications to the emissions control equipment, compliance with the 99.9999 percent destruction and removal efficiency (DRE) for PCBs in stack emissions required by the U.S. Environmental Protection Agency was achieved.     

Enhanced biodegradation of creosote-contaminated soil

Bioremediation, a viable option for treatment of cresote-contaminated soil, can be enhanced by the use of surfactant. A study was conducted to investigate the effect of a non-ionic surfactant, Triton X-100, on biodegradation of creosote-contaminated soil. Abiotic soil desorption experiments were performed to determine the kinetics of release of selected polynuclear aromatic hydrocarbon (PAH) compounds. Respirometric experiments were also conducted to evaluate the effect of nonionic surfactant on biodegradation. The N-Con system respirometer was used to monitor the oxygen uptake by the microorganisms. The abiotic experiments results indicated that the addition of surfactant to soil/water systems increased the desorption of PAH compounds. It was also observed that the desorption rate of PAH compounds depended on their molecular weight. The 3- and 4-ring PAH compounds showed higher and faster desorption rates than the 5- and 6-ring PAHs. The respirometric experiments indicated that an increase in soil contamination level from 112.5 to 771.8 mg/kg showed an increase in oxygen uptake. But for a soil contamination level of 1102.5 mg/kg, the oxygen uptake was similar to the contamination level of 771.8 mg/kg. This might be due to toxicity by the surfactant or the solubilized PAHs at high concentration or interference with contaminant transport into the cell or to reversible physical-chemical interferences with the activity of enzymes involved in the PAH degradation. The increase in PAH availability to the microorganisms in the aqueous phase produced an increase in oxygen consumption that is proportional to the biodegradation of organic compounds.     

An analysis of the composition and metal contamination of plastics from waste electrical and electronic equipment (WEEE)

The compositions of three WEEE plastic batches of different origin were investigated using infrared spectroscopy, and the metal content was determined with inductively coupled plasma. The composition analysis of the plastics was based mainly on 14 samples collected from a real waste stream, and showed that the major constituents were high impact polystyrene (42 wt%), acrylonitrile–butadiene–styrene copolymer (38 wt%) and polypropylene (10 wt%). Their respective standard deviations were 21.4%, 16.5% and 60.7%, indicating a considerable variation even within a single batch. The level of metal particle contamination was found to be low in all samples, whereas wood contamination and rubber contamination were found to be about 1 wt% each in most samples. In the metal content analysis, iron was detected at levels up to 700 ppm in the recyclable waste plastics fraction, which is of concern due to its potential to catalyse redox reactions during melt processing and thus accelerate the degradation of plastics during recycling. Toxic metals were found only at very low concentrations, with the exception of lead and cadmium which could be detected at 200 ppm and 70 ppm levels, respectively, but these values are below the current threshold limits of 1000 ppm and 100 ppm set by the Restriction of Hazardous Substances directive.     

Lead Speciation in the Sediments of the Heavily Polluted Western Harbor of Alexandria

The Western Harbor (WH) became under stress in the past decades, following successive increase in population. This study deals with local distribution of total lead and its species in the WH sediments. The lead content was high and there was a relationship between its enrichment and oil dispersed from ships. The lowest total lead value was found in the harbor middle far from direct effects of pollution. A five-step sequential extraction scheme was applied to illustrate the contribution shared by each individual fraction in the total lead concentration in the WH sediments. The exchangeable fraction (F1) was very low. The bound to carbonate fraction (F2), the bound to iron-manganese oxide fraction (F3) and the bound to organic matter—sulfide fraction (F4) ranked fourth, second and third in abundance. Oxygen was the main factor controlling the value of F2. F3 gave a direct relationship with total lead. The high levels of F4 occurred at locations of low salinity and enriched with organic matter. The residual fraction (F5) dominated other lead species, reflecting the sediment composition and the amounts of discharged pollutants.