固定化微生物对养殖水体中NH_4~ -N和NO_2~--N的转化作用

采用聚乙烯醇 (PVA) (ρ=gL-1)的方法对沼泽红假单胞菌、诺卡氏菌和假丝酵母 3种菌株进行固定化 ,所得的凝胶颗粒机械强度好 ,经久耐用 .运用这 3种菌株的固定化细胞对养殖水体中NH 4 N和NO-2 N进行转化 ,其最适作用温度范围为 2 5～ 30℃ ,最适pH范围分别为 :6 .5～ 8.5 ,7.0～ 7.5及 5 .5～ 7.0 ,且对水质初始氮浓度有很强的适应性 .3菌株经固定化后 ,其对养殖水体中NH 4 N和NO-2 N的转化效率明显优于其游离细胞 .若将 3菌株按 2 :1:2组合成复合菌株并固定化 ,其对养殖水体中的NH 4 N和NO-2 N转化效果将更佳 .图 3表 3参 9     

水稻不同时期吸收的氮素的行为

为研究水稻不同时期吸收的氮素在其体内的行为，作者利用^15NH^4＋和^15NO3^-双标记，对Indica水稻亚种（品种Hinohikari）进行水培，在分蘖期、幼穗分化期、开花期施用，将培养液卢州）20mg／L的NH4NO3换成相同质量浓度的^15TH4NO3或NH4^15NO3；部分水稻在一周后收获，其他分别在分蘖期、幼穗分化期、开花期、成熟期收获。植株分成根系、地上部的底部、地上部的顶部、旗叶和穗部，对各自的全氮、^15N进行测定，计算植物的总吸收量。从施用量、植株总吸收量以及三部分总和的植株氮残存量的比较来研究氮素在两种水稻亚种中的行为。研究结果表明，各个时期的^15NH4NO3或NH4^15NO3处理下水稻的N吸收总量上没有差别，但1周后收获的^15NH4-N处理的水稻中^15N的含量比^15NO3-N要高得多，直到成熟期收获的水稻都有同样的结果，这意味着各个时期吸收的NH4-N和NO3-N有着不同的损失量，吸收的NO3-N比NH4-N要损失得多。水稻叶片的氮素损失可能以N2O和NH3的形式。不同氮肥形态的处理下转移到穗部的氮素的量和来源也不相同，在NH4^15NO3的处理中穗部的^15N主要来自地上部的底部，而在^15NH4NO3的处理中穗部的^15N主要来自分蘖期吸收的^15N，少量来自成熟期并且^15N主要来自植株的各个部分。     

好氧脱氮微生物的混合培养条件

从土壤和水中筛选分离到混合脱氮微生物菌群，能在好氧条件下将NH4^ 一步转化为N2排放，整个过程无NO3^-的积累，混合脱氮微生物菌群培养的最佳碳源为NaHCO3和CH3COONa的混合物，质量浓度均为0.25gL^-1;（NH4）2SO4为氮源的最适质量浓度为0.2gL^-1；最适pH7-10；温度30℃；在混合脱氮微生物菌群的最适培养条件下，30h内氨氮去除率达98%以上，细胞生长质量浓度达2.9gL^-1，采用分批补料策略补加（NH4）2SO4使菌浓提高了31.0%，图6表4参11     

氮在水稻中的行为及其品种间的差别

目前氮肥的利用效率很低，很多研究重点放在氮肥在土壤过程中的损失，对植物本身的氮素损失较少注意。作者利用^15NH4^ 和^15NO3^-双标记，对Indica和Japonica水稻亚种进行水培，在分蘖期、幼穗分化期、开花期施用，将培养液ρ(N)20mg／L的NH4NO3换成相同质量浓度的^15NH4^ NO3或NH^15NO3^；部分水稻在一周后收获，其他分别在分蘖期、幼穗分化期、开花期、成熟期收获。植株分成根系、地上部和穗部，对各自的全氮、^15N进行测定，计算植物的总吸收量。从施用量、植株总吸收量以及三部分总和的植株氮残存量的比较来研究氮素在两种水稻亚种中的行为。研究结果表明，两种植物都近100％吸收了所施用的^15NH4NO3或NH4^15NO3，但^15NH4^ 和^15NO3^-在Japonica的残存量要比Indica多，损失的部分可能往大气中散失了，意味着两种水稻亚种有着明显不同的氮素利用率。比较^15NH4^ 和^15NO3^-的残存量，结果表明^15NH4^ 留在植株体内要比^15NO3^-多，尤其在抽穗期施用的情况下，植物体在后期对^15NO3^-的转化能力大大减弱，但这部分的氮如何损失掉尚不清楚。比较植株体内各部分的氮素含量，发现Japonica的穗部比Indica含有更多的氮素，表明氮在前者的体内转化效率和利用效率高。试验结果表明，不同水稻亚种对氮素的利用以及不同氮素形态在其体内的行为不同。     

南黄海不同粒度表层沉积物中可转化氮与环境因子的关系

南黄海不同粒度表层沉积物中可转化氮的形成与释放受环境因子的驱动作用各不相同,上覆水体的温度、盐度、pH值、DO的含量以及NH4^ 和NO3^-的含量都对其有一定的影响．其中DO是不同形态的氮形成与释放最显著的影响因素,这是因为上覆水体中DO的含量愈高,扩散进入表层沉积物中的O2就愈多,沉积物处于相对氧化的环境中,有机质的矿化作用较易进行,致使无机形态氮的含量相对较高,而有机形态氮的含量相对较低,所以其与可转化有机形态氮呈负相关,而与可转化无机形态氮呈正相关．温度与中、细粒度沉积物中的SOEF-N的含量呈显著正相关,可能是因为温度的升高加快了海洋底栖生物的生长发育,使生物排泄物和死亡残体增多,尽管温度的升高加快了沉积物中有机质的矿化分解,但由于中、细粒度沉积物堆积紧密,对温度的响应不明显,致使SOEF-N的含量随温度的升高而升高．上覆水体中的NH;和NO3^-分别与中、细粒度沉积物中的SAEF-N和SOEF-N的含量呈正相关,说明上覆水体中的NH4^ 和NO3^-主要来自于沉积物中SAEF-N和SOEF-N的形成与释放．另外,粗粒度沉积物中不同形态的氮对环境的响应较中、细粒度沉积物中的强．     

碳源及碳氮比对异养反硝化微生物异养反硝化作用的影响

碳源(甘油和柠檬酸钠)及碳氮比对纯培养的异养反硝化菌HP1(Pseudomonas alcaligenes)异养反硝化能力影响的试验表明，碳源种类对硝酸还原酶活性没有明显影响，对氧化亚氮还原酶活性有影响。批式培养方式下最适C／N为8，菌株HP1可以利用NO3^-f作为唯一氮源进行反硝化作用，证明HP1至少有2种硝酸还原途径。连续培养方式下温度对菌株HP1异养反硝化作用中间产物的积累有影响，不同C／N时均有NH4^ 积累，C／N为3时还有NO2^-的积累。     

非贵金属催化电解无害化去除硝酸盐氮的反应机制

以Ti/Co-Fe-Cu为阴极,Ti/IrO2-RuO2为阳极组成无隔膜电解体系,对非贵金属催化电解无害化去除NO3--N的反应机制进行了实验研究和理论分析.结果表明,NO3--N阴极催化还原过程中,反应物、产物需要通过对流、扩散作用,克服电场力,迁移至目标位置;在非贵金属的催化作用下,NO3--N受还原剂攻击,逐步还原为NH4+-N;还原中间产物NO-N和NH-N直接生成N2-N的过程受抑制,产物NH4+-N难以被再度直接氧化.添加Cl-作为支持电解质,实验电解体系发生阳极析氯、Cl2水解、NH4+-N氯氧化等过程,可将NH4+-N氧化为N2-N,且出水中NO3--N、NO2--N、氯胺类浓度很低.NO3--N无害化去除的反应机制是NO3--N在催化作用下,经传质、吸脱附、电子交换过程,还原为NH4+-N,NH4+-N经由Cl-→Cl2→HOCl→Cl-电解氯氧化循环,最终生成N2-N.     

三种载体上生物膜硝化作用动力学初步研究

通过测定水中COD、：NH4^ —N、NO2^-—N及NO3^-—N的浓度变化，研究了淹没式废水处理装置中沸石、活性炭和沙粒3种载体上硝化作用生物膜的动力学过程和反硝化作用。结果表明，3种载体上生物膜降解有机物(以COD表示)的过程可用一级动力学方程描述，反应速率常数分别为：沙粒0．0848h^-1、活性炭0．1187h^-1、沸石0．1334h^-1。3种载体上生物膜去除氨态氮的过程则可用零级动力学方程描述，反应速率常数分别为：沙粒-0．7743h^-1、活性炭-0．9886h^-1、沸石-1．0714h^-1．附着于沙上的生物膜去除亚硝酸盐氮的过程也可用零级动力学方程描述，反应速率常数为-0．6057h^-1，水中硝酸盐氮浓度较高时，载体沸石和活性炭上可能附着生长反硝化菌。图5表2参15。     

浅水体浮萍污水净化系统的除氮途径

以稀释的猪场厌氧污水为供试水样,少根紫萍为供试生物材料,对夏、冬2季浅水体浮萍污水净化系统TN、NH4 -N和NOx--N(NO2--N与NO3--N之和)的去除途径进行了试验研究。结果表明,在夏季气温条件下,TN通过气态氨挥发、浮萍系统吸收/吸附NH4 -N和NOx--N得以去除,3途径去除的N分别占TN去除量的30.5%、15.9%和53.6%;NH4 -N通过气态氨挥发、浮萍系统吸收/吸附和硝化反应得以去除,3途径去除的N分别占NH4 -N总去除量的33.1%、17.3%和49.6%;NOx--N则完全通过浮萍系统吸收/吸附得以去除。在冬季气温条件下,TN通过气态氨挥发和浮萍系统吸收/吸附NH4 -N得以去除,2途径去除的N分别占TN去除量的31.7%和68.3%;NH4 -N通过气态氨挥发、浮萍系统吸收/吸附和硝化反应得以去除,3途径去除的N分别占NH4 -N总去除量的28.9%、69.5%和1.6%;而水体中的NOx--N含量始终保持稳定。     

利用根箱法解析甜椒根际土壤中氮的行为(英文)

为研究甜椒根际土壤中氮的行为,与既报同样的方法进行研究,即,利用15NH4+,15NO3-双标记的硝胺(NH,4>15NO3,15NH4NO3),在温室里对甜椒进行6周的根箱栽培.收割后,对土壤全氮,NO3-N,水溶性NH4-N,KCl抽出NH4-N和其各自的15N atom%进行测定.结果表明,土壤全氮从非根际到根际逐渐增加,与栽培前相比,土壤全氮在非根际中减少,却在根际中增大.土壤NO3-N浓度朝根际增加到离根际2 mm处,然后激减到根际.NO3-N的来自施给NO3-N的比例靠近根际逐渐升高,在根际达到了69%,反而,来自施给NH4-N的比例靠近根际逐渐降低,在根际将至7%左右.水溶性NH4-N和KCl抽出NH4-N浓度靠近根际逐渐降低,而且,从非根际到根际,二者匀保持3∶10的比例.KCl抽出NH4-N的来自施给NO3-N的比例靠近根际逐渐升高,但在根际仍低于3%,反而,其来自施给NH4-N的比例在非根际约为47%～55%,在根际降到41%.在整个根箱里,施用NO3-N的有機率达到62%,但其值在根际比非根圈要低.相反,施用NH4-N的有機率仅11%左右,但其值在根际比非根际要高.以上结果表明,在甜椒根际土壤中氮的无机化-有机化活性与水稻相比显著低.     

SO2-4/TiO2对SO2-C7H16-TiO2复相光化学反应的影响

研究了TiO2与SO2,C7H16复相光化学反应的光催化活性.在SO2-C7H16-O2-TiO2光催化反应过程中,TiO2表面可形成SO2-4/TiO2结构,它的存在可提高庚烷的光催化氧化速率,利用IR和XPS研究了反应过程中TiO2表面形成的SO2-4/TiO2结构.     

Cu/Cr co-stabilization mechanisms in a simulated Al2O3-Fe2O3-Cr2O3-CuO waste system

• Cu and Cr can be mostly incorporated into CuFe_xAl_yCr_2−x−yO₄ with a spinel structure. • Spinel phase is the most crucial structure for Cu and Cr co-stabilization. • Compared to Al, Fe and Cr are easier to be incorporated into the spinel structure. • ‘Waste-to-resource’ by thermal process at attainable temperatures can be achieved. Chromium slag usually contains various heavy metals, making its safe treatment difficult. Glass-ceramic sintering has been applied to resolve this issue and emerged as an effective method for metal immobilization by incorporating heavy metals into stable crystal structures. Currently, there is limited knowledge about the reaction pathways adopted by multiple heavy metals and the co-stabilization functions of the crystal structure. To study the Cu/Cr co-stabilization mechanisms during thermal treatment, a simulated system was prepared using a mixture with a molar ratio of Al₂O₃:Fe₂O₃:Cr₂O₃:CuO= 1:1:1:3. The samples were sintered at temperatures 600–1300°C followed by intensive analysis of phase constitutions and microstructure development. A spinel phase (CuFe_xAl_yCr_2−x−yO₄) started to generate at 700°C and the incorporation of Cu/Cr into the spinel largely complete at 900°C, although the spinel peak intensity continued increasing slightly at temperatures above 900°C. Fe₂O₃/Cr₂O₃ was more easily incorporated into the spinel at lower temperatures, while more Al₂O₃ was gradually incorporated into the spinel at higher temperatures. Additionally, sintered sample microstructures became more condensed and smoother with increased sintering temperature. Cu / Cr leachability substantially decreased after Cu/Cr incorporation into the spinel phase at elevated temperatures. At 600°C, the leached ratios for Cu and Cr were 6.28% and 0.65%, respectively. When sintering temperature was increased to 1300°C, the leached ratios for all metal components in the system were below 0.2%. This study proposes a sustainable method for managing Cu/Cr co-exist slag at reasonable temperatures.     

KMnO4/H2SO4引发制备淀粉改性絮凝剂的研究

以高锰酸钾为引发剂,制备淀粉-丙烯酰胺接枝共聚物.研究酸浓度、引发剂浓度、单体浓度、温度和加料方式对接枝反应的影响.结果表明,少量KMnO4(0.45mmol·l-1)和H2SO4(0.8mmol·l-1)可有效引发淀粉-丙烯酰胺接枝共聚反应,接枝效率达到90%以上,分子量大大提高,对高岭土的絮凝效果较好.     

3D flower-like mesoporous Bi4O5I2/MoS2 Z-scheme heterojunction with optimized photothermal-photocatalytic performance

3D flower-like hierarchical mesoporous Bi₄O₅I₂/MoS₂ Z-scheme layered heterojunction photocatalyst was fabricated by oil bath and hydrothermal methods. The heterojunction with narrow band gap of ～1.95 eV extended the photoresponse to near-infrared region, which showed obvious photothermal effect due to the introduction of MoS₂ with broad spectrum response. MoS₂ nanosheets were anchored onto the surface of flower-like hierarchical m...     

Fe2O3-CeO2-Bi2O3/γ-Al2O3 catalyst in the catalytic wet air oxidation (CWAO) of cationic red GTL under mild reaction conditions

Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃, an environmental friendly material, was investigated. The catalyst exhibited good catalytic performance in the CWAO of cationic red GTL. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. HO₂· and O₂·⁻ appeared as the main reactive species in the reaction. The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst, a novel environmental-friendly material, was used to investigate the catalytic wet air oxidation (CWAO) of cationic red GTL under mild operating conditions in a batch reactor. The catalyst was prepared by wet impregnation, and characterized by special surface area (BET measurement), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst exhibited good catalytic activity and stability in the CWAO under atmosphere pressure. The effect of the reaction conditions (catalyst loading, degradation temperature, solution concentration and initial solution pH value) was studied. The result showed that the decolorization efficiency of cationic red GTL was improved with increasing the initial solution pH value and the degradation temperature. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. Hydroperoxy radicals (HO₂·) and superoxide radicals (O₂⁻·) appeared as the main reactive species upon the CWAO of cationic red GTL.     

Self-assembly synthesis of phosphorus-doped tubular g-C3N4/Ti3C2 MXene Schottky junction for boosting photocatalytic hydrogen evolution

Establishing highly effective charge transfer channels in carbon nitride(g-C₃N₄) to enhance its photocatalytic activity is still a challenging issue. Herein, the delaminated 2D Ti₃C₂ MXene nanosheets were employed to decorate the P-doped tubular g-C₃N₄(PTCN)for engineering 1D/2D Schottky heterojunction(PTCN/TC) through electrostatic self-assembly. The optimized PTCN/TC exhibited the highest hydrogen evolution rate(565 μmol h^-...     

磷酸活化活性炭对Cu2+的吸附特征研究

寻求廉价而高效的吸附材料为目的,研究向日葵秸杆基活性炭对铜离子的吸附性能。以向日葵秸秆为原料,经H3PO4活化制备活性炭,通过静态实验研究了其对水溶液中Cu2+的吸附特性,考察了溶液pH值、吸附温度和离子强度对吸附的影响,探讨了吸附热力学、动力学和吸附机理。结果表明:溶液pH值为5～6时活性炭对Cu2+的去除效果最好;向50 mL 170 mg·L-1的溶液中加入0.5 g活性炭,温度为45℃、吸附时间为1 h时,对Cu2+的去除率可达98.3%;Langmuir方程能更好地描述Cu2+在活性炭上的等温吸附特征,静态吸附容量可达41.03 mg·g-1;吸附过程符合拟二级动力学过程,且为吸热的化学吸附过程,膜扩散为速率控制步骤,离子交换可能在吸附过程中起了重要作用。     

Catalytic ozonation of organic compounds in water over the catalyst of RuO2/ZrO2-CeO2

This research investigates the performances of RuO₂/ZrO₂-CeO₂ in catalytic ozonation for water treatment. The results show that RuO₂/ZrO₂-CeO₂ was active for the catalytic ozonation of oxalic acid and possessed higher stability than RuO₂/Al₂O₃ and Ru/AC. In the catalytic ozonation of dimethyl phthalate (DMP), RuO₂/ZrO₂-CeO₂ did not enhance the DMP degradation rate but significantly improved the total organic carbon (TOC) removal rate. The TOC removal in catalytic ozonation was 56% more than that in noncatalytic ozonation. However this does not mean the catalyst was very active because the contribution of catalysis to the overall TOC removal was only 30%. The adsorption of the intermediates on RuO₂/ZrO₂-CeO₂ played an important role on the overall TOC removal while the adsorption of DMP on it was negligible. This adsorption difference was due to their different ozonation rates. In the catalytic ozonation of disinfection byproduct precursors with RuO₂/ZrO₂-CeO₂, the reductions of the haloacetic acid and trihalomethane formation potentials (HAAFPs and THMFPs) for the natural water samples were 38%–57% and 50%–64%, respectively. The catalyst significantly promoted the reduction of HAAFPs but insignificantly improved the reduction of THMFPs as ozone reacts fast with the THMs precursors. These results illustrate the good promise of RuO₂/ZrO₂-CeO₂ in catalytic ozonation for water treatment.     

Immobilization of Cu2+, Zn2+, Pb2+, and Cd2+ during geopolymerization

The present research explored the application of geopolymerization for the immobilization and solidification of heavy metal added into metakaolinte. The compressive strength of geopolymers was controlled by the dosage of heavy metal cations, and geopolymers have a toleration limit for heavy metals. The influence of alkaline activator dosage and type on the heavy metal ion immobilization efficiency of metakaolinte-based geopolymer was investigated. A geopolymer with the highest heavy metal immobilization efficiency was identified to occur at an intermediate Na₂SiO₃ dosage and the metal immobilization efficiency showed an orderly increase with the increasing Na⁺ dosage. Geopolymers with and without heavy metals were analyzed by the X-ray powder diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. No crystalline phase containing heavy metals was detected in geopolymers with heavy metal, suggesting that the crystalline phase containing heavy metals is not produced or most of the phases incorporating heavy metals are amorphous. FTIR spectroscopy showed that, with increasing heavy metal addition, an increase in NO3- peak intensity was observed, which was accompanied by a decrease in the CO32- peak.     

六铝酸盐负载CuO催化还原NO性能

采用共沉淀法制备了LaAl12O19六铝酸盐载体,采用等体积浸渍法制备了不同负载量的CuO/LaAl12O19催化剂,并对其进行了XRD、H2-TPR和BET表征,考察了催化剂对CH4选择催化还原NO的性能.结果表明,CuO的负载并未改变六铝酸盐载体的结构,Cu在载体上以Cu2+的形式存在,活性组分CuO与载体LaAl12O19之间存在协同作用;CuO/LaAl12O19催化剂对CH4选择催化还原NO表现出良好活性,所制备的催化剂均能使NO的转化率达到99%;其中负载量为1.0 wt%的CuO/LaAl12O19催化剂的活性最好,完全反应温度T99%为560℃,且在80 h稳定性试验中表现出了良好的高温活性和热稳定性.