一株耐盐好氧反硝化细菌的分离鉴定及其脱氮特性

从处理高盐废水的生物接触氧化工艺成熟活性污泥中分离得到一株耐盐好氧反硝化细菌F10.根据形态学特征、生理生化以及16S rRNA基因序列测定分析,初步判定该菌株为盐单胞菌属(Halomonas sp.).菌株能在盐度为3%~7%的培养基中良好的生长及脱氮,最适盐度为3%(以Na Cl计),最适碳源为乙酸钠,最适p H为7~8,最适温度为30℃.该菌株能利用NO-3-N进行反硝化作用,在盐度为3%的反硝化培养基中24 h内对NO-3-N的去除率达到92.6%,36 h基本完全去除。该菌株在3%盐度下表现出良好的异养硝化-好氧反硝化性能,初始硝态氮浓度在270 mg/L时,菌株的脱氮率可达90%以上,氨氮的去除率可达75%以上,脱氮过程中无NO-2-N积累,可实现同步硝化反硝化,具有一定的工程应用价值。     

马兰黄土中与三氮有关的微生物的分布及其反硝化能力

选择关中盆地马兰黄土为研究对象,采用平板菌落计数法研究了与三氮转化有关的微生物在0～9 m剖面上的垂直分布.结果表明,剖面上氨化细菌、硝化细菌、反硝化细菌、固氮菌分别为克土106～1010、101～103、103～108、103～105个.在试验区剖面7 m处的土壤中存在着反硝化菌富集区,数量达克土108个.对此层位土壤进行了反硝化能力实验,结果表明,马兰黄土反硝化作用最适宜温度为22 ℃和37 ℃,碳源的存在可大大提高反硝化速率,但改变碳氮比对反硝化速率影响不大.在15 ℃、无外界供给碳源、硝酸根初始质量浓度为56 mg/L情况下,反硝化菌对硝酸根的降解作用符合方程y=-2.682 8x 60.979,回归系数R=0.960 9.该反硝化菌富集区的存在为研究包气带中三氮转化提供了重要信息.     

两阶段曝气生物滤池的硝化性能

曝气生物滤池(BAF)是近年来受到广泛关注的一种新型污水处理技术,具有占地面积少、投资费用低、处理效率高、出水水质好等优点。现已被应用于许多污水处理厂的二级处理、深度处理以及污水的回用。实验以陶粒为填料,自行设计了升流式两阶段BAFs(UBAFs)处理模拟生活污水,考察了反应器运行条件对COD与氨氮去除影响,并探讨了UBAFs反应器内氮流失及同步硝化反硝化情况。结果表明,UBAFs对生活污水处理具有良好的净化效果。在进水COD和氨氮浓度分别为200~363 mg/L和16.8~31.3 mg/L条件下,UBAFs处理出水水质均达到《城市污水再生利用城市杂用水水质》(GB/T 18920-2002)标准,能够满足回用要求。通过采用氮平衡分析方法和借助电子扫描电镜技术,初步认为UBAFs反应器脱氮方式是由于在UBAFs第一阶段局部厌氧环境中以传统方式进行硝化反硝化脱氮,第二阶段是在好氧条件下,异养好氧硝化菌的同步硝化反硝化脱氮。     

苯污染地下水系统更硝化菌分布及其净化过程

生物降解作用是地下水系统有机污染物自然衰减过程中最重要的破坏性衰减机制。在分析中，以我国某受苯污染水源地的地下水系统为对象，研究了该地下水中反硝化菌的分布，筛选出2株土著反硝化菌，通过生物降解实验证明其具有降解苯的能力，同时结合水源地历年的水质监测数据，首次从地球化学及生物学2个方面说明了该地下水中存在反硝化菌对苯的生物净化作用，为进一步研究该地下水中苯自然衰减规律奠定基础。     

苯污染地下水系统反硝化菌分布及其净化过程

生物降解作用是地下水系统有机污染物自然衰减过程中最重要的破坏性衰减机制。在分析中,以我国某受苯污染水源地的地下水系统为对象,研究了该地下水中反硝化菌的分布,筛选出2株土著反硝化菌,通过生物降解实验证明其具有降解苯的能力,同时结合水源地历年的水质监测数据,首次从地球化学及生物学2个方面说明了该地下水中存在反硝化菌对苯的生物净化作用,为进一步研究该地下水中苯自然衰减规律奠定基础。     

基于好氧反硝化反应器的海水脱氮性能及动力学特征

以去除海水循环水养殖系统中硝酸盐(NO_3~--N)为目的,通过接种好氧反硝化细菌的方式构建海水好氧反硝化反应器,对其反硝化脱氮性能和动力学特征展开研究。研究结果显示,好氧反硝化反应器完成挂膜需要15 d。在有氧条件下,反应器对NO_3~--N浓度为30～150 mg·L-1海水具有良好的反硝化性能,NO_3~--N的去除率达到90%以上。批次实验结果显示:好氧反硝化过程呈现阶段性,NO_3~--N在整个过程中可被高效去除;NO_2~--N积累最大值随初始NO_3~--N浓度的增大而增大,且初始NO_3~--N浓度越高,NO_2~--N完全去除所需时间越长。采用Monod方程的微分方程模型,能够很好地拟合反硝化过程中NO_3~--N、NO_2~--N的变化趋势。该好氧反硝化反应器具有良好的脱氮性能,为解决循环水养殖系统NO_3~--N积累问题提供了新的思路。     

实时控制SBR系统中的短程硝化反硝化

以人工模拟高氨氮废水为研究对象,采用循环间歇式曝气方式,以溶解氧浓度(DO)和pH值为过程控制参数,对SBR系统进行实时控制、全程跟踪.根据此过程中COD、NH4 -N、NO2--N和NO3--N 4项水质指标的变化情况,研究SBR系统中的短程硝化反硝化工艺.实验结果表明,在短程硝化反硝化工艺中,采用较高曝气量,并且在曝气过程中用DO和pH值作为过程控制参数是可行的.     

低氧条件下同时硝化和反硝化机理初探

采用人工配水 ,对低氧条件下完全混合系统中氮的去除进行了研究。实验结果表明 ,在低氧条件下 (DO为 0 .3～0 .8mg/L )完全混合系统的同时硝化和反硝化具有一定的可行性。在泥龄为 45 d,C/N比为 10∶ 1,F/M为 0 .1g CODCr/(g ML SS·d)条件下 ,总氮的去除率达 66.7%。经分析 ,本实验发生的硝化反应仍然是自养硝化菌的好氧硝化 ,同时硝化和反硝化现象应归因于微环境理论     

膜生物反应器同步硝化反硝化系统的研究

设计结构合理的膜生物反应器,驯化培养硝化污泥,复配反硝化细菌,构建了具有同步硝化反硝化功能且能去除COD的膜生物反应器系统.MLVSS的增高和污泥结构的改善为同步硝化反硝化提供条件.进水氨氮浓度在50 mg/L,MLVSS为8 g/L时,最佳HRT为4～6 h,气量控制在0.5 m3/h左右,TN去除率达80%以上.系统承受负荷变化范围0～0.36 kg N/(m3·d),TN去除率均能保持80%左右,COD去除率稳定在90%.系统投加粉末活性炭的方法可以改善污泥结构,进而减轻膜污染.在试验阶段内,添加了PAC的活性污泥MLVSS的高低对膜通量的影响不大,膜通量基本保持稳定.     

一株高效异养硝化-好氧反硝化菌的分离鉴定及脱氮性能

从经驯化的污泥中筛选出一株异养硝化-好氧反硝化细菌,编号为TN-05,通过形态学特征观察,生理生化特征试验和核酸序列分析鉴定其为门多萨假单胞菌（pseudomonasmendocina）。同时对其进行脱氮性能研究,结果表明,TN-05具有较好的异养硝化能力,菌株在培养至48h时对总氮和氨氮去除率均能达95％以上。通过反硝化能力验证实验发现,菌株对NO3-N和N0f—N也分别具有较好的去除效率。将菌株应用于人工合成废水中,发现对废水中氨氮优先利用并能在24h时使去除率接近100％,对硝态氮和亚硝态氮也具有一定的去除效率。因此,菌株TN-05是一株同时具备异养硝化和好氧反硝化能力的高效菌株。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.