Optimum moisture levels for biodegradation of mortality composting envelope materials

Moisture affects the physical and biological properties of compost and other solid-state fermentation matrices. Aerobic microbial systems experience different respiration rates (oxygen uptake and CO2 evolution) as a function of moisture content and material type. In this study the microbial respiration rates of 12 mortality composting envelope materials were measured by a pressure sensor method at six different moisture levels. A wide range of respiration (1.6-94.2mg O2/g VS-day) rates were observed for different materials, with alfalfa hay, silage, oat straw, and turkey litter having the highest values. These four envelope materials may be particularly suitable for improving internal temperature and pathogen destruction rates for disease-related mortality composting. Optimum moisture content was determined based on measurements across a range that spans the maximum respiration rate. The optimum moisture content of each material was observed near water holding capacity, which ranged from near 60% to over 80% on a wet basis for all materials except a highly stabilized soil compost blend (optimum around 25% w.b.). The implications of the results for moisture management and process control strategies during mortality composting are discussed.     

Prediction of temperature and thermal inertia effect in the maturation stage and stockpiling of a large composting mass

A macroscopic non-steady state energy balance was developed and solved for a composting pile of source-selected organic fraction of municipal solid waste during the maturation stage (13,500 kg of compost). Simulated temperature profiles correlated well with temperature experimental data (ranging from 50 to 70 degrees C) obtained during the maturation process for more than 50 days at full scale. Thermal inertia effect usually found in composting plants and associated to the stockpiling of large composting masses could be predicted by means of this simplified energy balance, which takes into account terms of convective, conductive and radiation heat dissipation. Heat losses in a large composting mass are not significant due to the similar temperatures found at the surroundings and at the surface of the pile (ranging from 15 to 40 degrees C). In contrast, thermophilic temperature in the core of the pile was maintained during the whole maturation process. Heat generation was estimated with the static respiration index, a parameter that is typically used to monitor the biological activity and stability of composting processes. In this study, the static respiration index is presented as a parameter to estimate the metabolic heat that can be generated according to the biodegradable organic matter content of a compost sample, which can be useful in predicting the temperature of the composting process.     

Changes in organic matter composition during composting of two digested sewage sludges

Changes in the chemical and chemical-structural composition of the organic matter of two different sewage sludges (aerobic and anaerobic) mixed with sawdust (1:1 and 1:3, v/v) during composting were determined by monitoring chemical and microbiological parameters as well as by pyrolysis-gas chromatography. Composting was carried out in periodically turned outdoor piles, which were sampled for analysis 1, 30, 60 and 90 days after the beginning of the composting process. Both volatile organic matter and the water soluble C fraction decreased during composting, indicating that the more labile C fractions are mineralized during the process. Microbial activity as measured by microbial respiration (CO(2) evolved from compost samples during incubation) also decreased with composting, reflecting the more stable character of the resulting compost. No major differences were observed between the four composts studied as regards their chemical-structural characteristics. The acetonitrile, acetic acid and phenol pyrolytic fragment tended to increase with composting. Although the final composts were more aromatic in nature than the starting materials, a low degree of humification was observed in all four composts studied, as determined by their high proportion of polysaccharides and alkyl compounds. For this reason, the relationship between pyrolytic fragments, such as benzene/toluene or benzene+toluene/pyrrol+phenols, which are used as indices of humification for soil organic matter, are not of use for such poorly evolved sludge composts; instead, ratios that involve carbohydrate derivatives and aromatic compounds, such as furfural+acetic/benzene+toluene or acetic/toluene, are more sensitive indices for reflecting the transformations of these materials during composting. Both the chemical and microbiological parameters and pyrolytic analysis provided valuable information concerning the nature of the compost's organic matter and its changes during the composting process.     

Green house gas emissions from composting and mechanical biological treatment.

In order to carry out life-cycle assessments as a basis for far-reaching decisions about environmentally sustainable waste treatment, it is important that the input data be reliable and sound. A comparison of the potential greenhouse gas (GHG) emissions associated with each solid waste treatment option is essential. This paper addresses GHG emissions from controlled composting processes. Some important methodological prerequisites for proper measurement and data interpretation are described, and a common scale and dimension of emission data are proposed so that data from different studies can be compared. A range of emission factors associated with home composting, open windrow composting, encapsulated composting systems with waste air treatment and mechanical biological waste treatment (MBT) are presented from our own investigations as well as from the literature. The composition of source materials along with process management issues such as aeration, mechanical agitation, moisture control and temperature regime are the most important factors controlling methane (CH4), nitrous oxide (N2O) and ammoniac (NH3) emissions. If ammoniac is not stripped during the initial rotting phase or eliminated by acid scrubber systems, biofiltration of waste air provides only limited GHG mitigation, since additional N2O may be synthesized during the oxidation of NH3, and only a small amount of CH4 degradation occurs in the biofilter. It is estimated that composting contributes very little to national GHG inventories generating only 0.01-0.06% of global emissions. This analysis does not include emissions from preceding or post-treatment activities (such as collection, transport, energy consumption during processing and land spreading), so that for a full emissions account, emissions from these activities would need to be added to an analysis.     

Contribution of the lignocellulosic fraction of two-phase olive-mill wastes to the degradation and humification of the organic matter during composting

One of the main disadvantages in the composting of two-phase olive mill wastes (TPOMW) is the long time required for its transformation (up to 40 weeks). The aim of this work was to evaluate the relationship between the degradation of the lignocellulosic fraction of TPOMW and the organic matter (OM) mineralisation rate in four composting piles prepared with different bulking agents and N-sources used to enhance OM degradation. The kinetics of degradation of the lignocellulosic fraction was compared to conventional maturation and stability indices to evaluate its impact on the duration of the composting process. The composition of bulking agents mainly affected the water-soluble fraction which influenced the OM degradation rate (linear or exponential OM degradation pattern) at early stages of the composting process but it neither modified the duration of the process (between 34 and 36 weeks) nor the total OM degradation underwent by the piles. The high initial mineral N availability was a key factor to significantly enhanced microbial activity. The mixture with urea as N-source registered the most efficient degradation of hemicellulose, cellulose and lignin, reducing the thermophilic phase and the total duration of TPOMW composting.     

A complete mass balance of a complex combined anaerobic/aerobic municipal source-separated waste treatment plant

In this study a combined anaerobic/aerobic full-scale treatment plant designed for the treatment of the source-separated organic fraction of municipal solid waste (OFMSW) was monitored over a period of one year. During this period, full information was collected about the waste input material, the biogas production, the main rejects and the compost characteristics. The plant includes mechanical pre-treatment, dry thermophilic anaerobic digestion, tunnel composting system and a curing phase to produce compost. To perform the monitoring of the entire plant and the individual steps, traditional chemical methods were used but they present important limitations in determining the critical points and the efficiency of the stabilization of the organic matter. Respiration indices (dynamic and cumulative) allowed for the quantitative calculation of the efficiency of each treatment unit. The mass balance was calculated and expressed in terms of Mgy(-1) of wet (total) matter, carbon, nitrogen and phosphorus. Results show that during the pre-treatment step about 32% of the initial wet matter is rejected without any treatment. This also reduces the biodegradability of the organic matter that continues to the treatment process. About 50% of the initial nitrogen and 86.4% of the initial phosphorus are found in the final compost. The final compost also achieves a high level of stabilization with a dynamic respiration index of 0.3±0.1g O(2) per kg of total solids per hour, which implies a reduction of 93% from that of the raw OFMSW, without considering the losses of biodegradable organic matter in the refuse (32% of the total input). The anaerobic digestion process is the main contributor to this stabilization.     

A kinetic analysis of solid waste composting at optimal conditions

This discussion explores the possibility of having a measure of the biodegradable organic carbon content in solid wastes. Currently, indirect measures for determining the concentration of biodegradable organic matter are being used and most of them are based on respiration indices (oxygen consumption or carbon dioxide production) or chemical parameters (volatile solids or total organic carbon). The results obtained for the cumulative carbon dioxide production in composting experiments can be expressed as "aerobic biodegradable carbon" for the wastes that were studied. The calculation of a useful biodegradable C/N can also be obtained from the aerobic biodegradable carbon content. A comparison with some results obtained in measuring the concentration of "anaerobic biodegradable carbon" also is presented.     

CH4 and N2O from mechanically turned windrow and vermicomposting systems following in-vessel pre-treatment

Methane (CH4) and nitrous oxide (N2O) are included in the six greenhouse gases listed in the Kyoto protocol that require emission reduction. To meet reduced emission targets, governments need to first quantify their contribution to global warming. Composting has been identified as an important source of CH4 and N2O. With increasing divergence of biodegradable waste from landfill into the composting sector, it is important to quantify emissions of CH4 and N2O from all forms of composting and from all stages. This study focuses on the final phase of a two stage composting process and compares the generation and emission of CH4 and N2O associated with two differing composting methods: mechanically turned windrow and vermicomposting. The first stage was in-vessel pre-treatment. Source-segregated household waste was first pre-composted for seven days using an in-vessel system. The second stage of composting involved forming half of the pre-composted material into a windrow and applying half to vermicomposting beds. The duration of this stage was 85 days and CH4 and N2O emissions were monitored throughout for both systems. Waste samples were regularly subjected to respirometry analysis and both processes were found to be equally effective at stabilising the organic matter content. The mechanically turned windrow system was characterised by emissions of CH4 and to a much lesser extent N2O. However, the vermicomposting system emitted significant fluxes of N2O and only trace amounts of CH4. In-vessel pre-treatment removed considerable amounts of available C and N prior to the second stage of composting. This had the effect of reducing emissions of CH4 and N2O from the second stage compared to emissions from fresh waste found in other studies. The characteristics of each of the two composting processes are discussed in detail. Very different mechanisms for emission of CH4 and N2O are proposed for each system. For the windrow system, development of anaerobic zones were thought to be responsible for CH4 release. High N2O emission rates from vermicomposting were ascribed to strongly nitrifying conditions in the processing beds combined with the presence of de-nitrifying bacteria within the worm gut.     

CIELAB color variables as indicators of compost stability

The composting process of different organic wastes both in laboratory and on a large-scale was characterized using CIELAB color variables to evaluate compost stability for the better application in agriculture. The time courses of the CIELAB variables of composting materials were determined directly from the bottom of a glass petri dish filled with dried and ground samples using a Minolta Color Reader (CR-13) calibrated with clean empty petri dishes placed on a white tile. To compare the proposed method with conventional methods, the same materials were also evaluated using commonly used compost stability evaluation indices. Most of the CIELAB variables of a compost made from a mixture of green tea waste and rice bran reached a plateau after 84 days of composting and showed strong relationships with the commonly used compost stability evaluation indices. The time needed for CIELAB variables, especially the L*and b* values, to stabilize at large-scale composting plants of cattle litter, farmyard manure, kitchen garbage and bark compost, were more or less similar to the times of maturation evaluated by the respective compost producers. The CIELAB color variable offers a new, simple, rapid and inexpensive means of evaluating compost stability and its quality prior to agricultural use.     

Mass and element balance in food waste composting facilities

The mass and element balance in municipal solid waste composting facilities that handle food waste was studied. Material samples from the facilities were analyzed for moisture, ash, carbon, nitrogen, and the oxygen consumption of compost and bulking material was determined.Three different processes were used in the food waste composting facilities: standard in-vessel composting, drying, and stand-alone composting machine. Satisfactory results were obtained for the input/output ash balance despite several assumptions made concerning the quantities involved. The carbon/nitrogen ratio and oxygen consumption values for compost derived only from food waste were estimated by excluding the contribution of the bulking material remaining in the compost product. These estimates seemed to be suitable indices for the biological stability of compost because there was a good correlation between them, and because the values seemed logical given the operating conditions at the facilities.     

Home composting versus industrial composting: Influence of composting system on compost quality with focus on compost stability

Stability is one of the most important properties of compost obtained from the organic fraction of municipal solid wastes. This property is essential for the application of compost to land to avoid further field degradation and emissions of odors, among others. In this study, a massive characterization of compost samples from both home producers and industrial facilities is presented. Results are analyzed in terms of chemical and respiration characterizations, the latter representing the stability of the compost. Results are also analyzed in terms of statistical validation. The main conclusion from this work is that home composting, when properly conducted, can achieve excellent levels of stability, whereas industrial compost produced in the studied facilities can also present a high stability, although an important dispersion is found in these composts. The study also highlights the importance of respiration techniques to have a reliable characterization of compost quality, while the chemical characterization does not provide enough information to have a complete picture of a compost sample.     

Composting toilets as a sustainable alternative to urban sanitation – A review

In today’s flush based urban sanitation systems, toilets are connected to both the centralized water and wastewater infrastructures. This approach is not a sustainable use of our water and energy resources. In addition, in the U.S., there is a shortfall in funding for maintenance and upgrade of the water and wastewater infrastructures. The goal of this paper was to review the current knowledge on composting toilets since this technology is decentralized, requires no water, creates a value product (fertilizer) and can possibly reduce the burden on the current infrastructure as a sustainable sanitation approach. We found a large variety of composting toilet designs and categorized the different types of toilets as being self contained or central; single or multi chamber; waterless or with water/foam flush, electric or non-electric, and no-mix or combined collection. Factors reported as affecting the composting process and their optimum values were identified as; aeration, moisture content (50–60%), temperature (40–65 °C), carbon to nitrogen ratio (25–35), pH (5.5–8.0), and porosity (35–50%). Mass and energy balance models have been created for the composting process. However there is a literature gap in the use of this knowledge in design and operation of composting toilets. To evaluate the stability and safety of compost for use as fertilizer, various methods are available and the temperature–time criterion approach is the most common one used. There are many barriers to the use of composting toilets in urban settings including public acceptance, regulations, and lack of knowledge and experience in composting toilet design and operation and program operation.     

Effects of air flow directions on composting process temperature profile

In this study, chicken manure mixed with carnation wastes was composted by using three different air flow directions: R1-sucking (downward), R2-blowing (upward) and R3-mixed. The aim was to find out the most appropriate air flow direction type for composting to provide more homogenous temperature distribution in the reactors. The efficiency of each aeration method was evaluated by monitoring the evolution of parameters such as temperature, moisture content, CO(2) and O(2) ratio in the material and dry material losses. Aeration of the reactors was managed by radial fans. The results showed that R3 resulted in a more homogenous temperature distribution and high dry material loss throughout the composting process. The most heterogeneous temperature distribution and the lowest dry material loss were obtained in R2.     

Determination of nitrous oxide, methane, and ammonia emissions from a swine waste composting process

The amounts of harmful gas emissions from the process of composting swine waste were determined using an experimental composting apparatus. Forced aeration (19.2–96.1 l/m³/min) was carried out continuously, and exhaust gases were collected and analyzed periodically. With weekly turning and the addition of a bulking agent in order to decrease the moisture content and increase air permeability, the temperature of most of the contents rose to 70°C and composting was complete within 3–5 weeks. NH₃, CH₄, and N₂O emissions were high in the early stage of composting. About 10%–25% of the nitrogen in the raw material was lost as NH₃ gas during composting. The emission rate of NH₃ mainly depended on the aeration rate, so that as the aeration rate rose, the level of NH₃ emissions increased. The CH₄ and N₂O emissions could be kept lower with adequate treatment at more than 40 l/m³/min aeration. N₂O may be mainly the result of the denitrification of NO _x -N in the additional matured compost used as a composting accelerator. Received: September 11, 1998 / Accepted: November 8, 1999     

Field scale evaluation of volatile organic compound production inside biosecure swine mortality composts

Emergency mortality composting associated with a disease outbreak has special requirements to reduce the risks of pathogen survival and disease transmission. The most important requirements are to cover mortalities with biosecure barriers and avoid turning compost piles until the pathogens are inactivated. Temperature is the most commonly used parameter for assessing success of a biosecure composting process, but a decline in compost core temperature does not necessarily signify completion of the degradation process. In this study, gas concentrations of volatile organic compounds (VOCs) produced inside biosecure swine mortality composting units filled with six different cover/plant materials were monitored to test the state and completion of the process. Among the 55 compounds identified, dimethyl disulfide, dimethyl trisulfide, and pyrimidine were found to be marker compounds of the process. Temperature at the end of eight weeks was not found as an indicator of swine carcass degradation. However, gas concentrations of the marker compounds at the end of eight weeks were found to be related to carcass degradation. The highest gas concentrations of the marker compounds were measured for the test units with the lowest degradation (highest respiration rates). Dimethyl disulfide was found to be the most robust marker compound as it was detected from all composting units in the eighth week of the trial. Concentration of dimethyl disulfide decreased from a range of 290–4340 ppmv to 6–160 ppbv. Dimethyl trisulfide concentrations decreased to a range of below detection limit to 430 ppbv while pyrimidine concentrations decreased to a range of below detection limit to 13 ppbv.     

Investigation and optimization of composting processes-test systems and practical examples

To determine the optimal course of composting it is useful to carry out experiments. The selection of the right experimental set-up depends on the question of concern. Each set-up is useful for a particular application and has its limits. Two test systems of different scales (up to 1500 ml; up to 100 l) are introduced. The purpose and importance of each system design shall be highlighted by application examples: (1). Suitability of a liquid industrial residue as composting accelerator; (2). Determination of the compost maturity; (3). Behaviour of odor-reducing additives during waste collection and composting; (4). Production of tailor-made compost with respect to Nitrogen (5). Suitability of O(2)-enriched air for acceleration of composting. Small-scale respiration experiments are useful to optimize parameters which have to be adjusted during substrate pre-treatment and composting, with the exception of particle size and temperature, and to reduce the number of variants which have to be investigated in greater detail in larger scale experiments. As all regulation possibilities such as aeration, moistening, turning can be simulated with the technical scale set-up, their complex cooperation can be taken into consideration. Encouraging composting variants can be tested, compared and optimized.     

Comparison of aerobic and anaerobic stability indices through a MSW biological treatment process

A complex mechanical-biological waste treatment plant designed for the processing of mixed municipal solid wastes (MSW) and source-selected organic fraction of municipal solid wastes (OFMSW) has been studied by using stability indices related to aerobic (respiration index, RI) and anaerobic conditions (biochemical methane potential, BMP). Several selected stages of the plant have been characterized: waste inputs, mechanically treated wastes, anaerobically digested materials and composted wastes, according to the treatment sequence used in the plant. Results obtained showed that the main stages responsible for waste stabilization were the two first stages: mechanical separation and anaerobic digestion with a diminution of both RI and BMP around 40% and 60%, respectively, whereas the third stage, composting of digested materials, produced lesser biological degradation (20-30%). The results related to waste stabilization were similar in both lines (MSW and OFMSW), although the indices obtained for MSW were significantly lower than those obtained for OFMSW, which demonstrated a high biodegradability of OFMSW. The methodology proposed can be used for the characterization of organic wastes and the determination of the efficiency of operation units used in mechanical-biological waste treatment plants.     

Maturity assessment of compost from municipal solid waste through the study of enzyme activities and water-soluble fractions

In this work the dynamics of biochemical (enzymatic activities) and chemical (water-soluble fraction) parameters during 100 days of municipal solid wastes composting were studied to evaluate their suitability as tools for compost characterization. The hydrolase (protease, urease, cellulase, beta-glucosidase) and dehydrogenase activities were characterized by significant changes during the first 2 weeks of composting, because of the increase of easily decomposable organic compounds. After the 4th week a "maturation phase" was identified in which the enzymatic activities tended to gently decrease, suggesting the stabilisation of organic matter. Also the water-soluble fractions (water-soluble carbon, nitrogen, carbohydrates and phenols), which are involved in many degradation processes, showed major fluctuations during the first month of composting. The results obtained showed that the hydrolytic activities and the water-soluble fractions did not vary statistically during the last month of composting. Significant correlations between the enzymatic activities, as well as between enzyme activities and water-soluble fractions, were also highlighted. These results highlight the suitability of both enzymatic activities and water soluble fractions as suitable indicators of the state and evolution of the organic matter during composting. However, since in the literature the amount of each activity or fraction at the end of composting depends on the raw material used for composting, single point determinations appear inadequate for compost characterization. This emphasizes the importance of the characterization of the dynamics of enzymatic activities and water-soluble fractions during the process.     

Influences of winery–distillery waste compost stability and soil type on soil carbon dynamics in amended soils

The application of organic materials to replenish soil organic matter and improve soil structure and fertility has become a common agronomic practice. This research deals with the effects of soil amendment with winery and distillery waste composts on organic carbon (C) mineralisation in two arable soils. A sandy-loam and clay-loam soil were treated and incubated with a number organic materials obtained from the co-composting of different proportions of grape stalk, grape marc, exhausted grape marc and vinasse, with sewage sludge or animal manure. Moreover, the effect of compost stability on C mineralisation dynamics was studied by applying organic materials from different stages of the composting process. The results obtained showed that the addition of exogenous organic matter stimulated microbial growth, enhanced soil respiration and increased water-extractable C contents in both soils, particularly in the days immediately following amendment. The initial composition of the different organic materials used, especially for the mature samples, and the texture of the receiving soil did not influence significantly the C mineralisation final values, with around 11–20% of the added organic C being mineralised over the first 140 days. However, the contribution of organic amendment to the labile organic C pool, maximum rates of soil respiration, as well as the extent of initial disturbance of the soil microbiota were all found to be related to the degree of organic matter stability. Moreover, irrespective of the type and stability of the organic amendment, the mineralogical composition of the receiving soil was found to significantly influence its resilience in such systems.     

Analysis of branched-chain fatty acids in humic substances as indices for compost maturity by pyrolysis–gas chromatography/mass spectrometry with tetramethylammonium hydroxide (TMAH-py–GC/MS)

Parameters that affect the degree of humification for humic substances (HSs) are deeply related to the maturity of the compost. In general, the matured composts contain HSs with a higher degree of humification. In addition, microbial activities during composting are also one of the indices for compost maturation. Branched-chain fatty acids are metabolites as the result of microbial activities in a soil environment. Such branched-chain fatty acids, regarded as humic precursors, are incorporated into HSs during the composting process. To determine whether branched-chain fatty acids in HSs can be used as biomarkers during composting processes or not, HSs were extracted from three types of composts with the different maturation, and the branched-chain fatty acids in the HSs were analyzed by pyrolysis–gas chromatography/mass spectrometry with tetramethylammonium hydroxide (TMAH-py–GC/MS). HSs with a higher degree of humification (higher aromaticity and lower molecular weight) contained higher levels of branched-chain fatty acids. These results show that branched-chain fatty acids in HSs from matured compost samples can be used as biomarkers, which indicate the history of microbial activities during overall composting process.