Partitioning of polychlorinated biphenyls in octanol/water, triolein/water, and membrane/water systems

The use of the octanol/water partition constant (Kow) as a surrogate parameter for lipid/water partitioning of persistent organic pollutants (POPs) was reassessed by comparing the measured Kow of 12 selected polychlorinated biphenyl congeners (PCBs) with partition constants in triolein/water (Ktw) and membrane/water (Kmw) systems. Kow and Ktw were measured by the slow-stirring method. Kmw was measured by an adaptation of the slow-stirring method using suspensions of phosphatidylcholine and phosphatidylserine liposomes. Partitioning of POPs to octanol, triolein, and liposomes is similar but not equal. The log-log correlation for Kow and Ktw is excellent (r2 = 0.982) and that for Kow and Kmw is somewhat weaker (r2 = 0.856). Ktw values are greater than Kow by a factor of 1.6. Kmw of some PCB congeners exceed both Kow and Ktw by an order of magnitude. The differences are attributed to different PCB activity coefficients in the different lipid phases. The results imply that Kow can be used as a reasonable conservative estimate of lipid/water partitioning. But the observed differences between Kow and Kmw also indicate that using Kow to predict accumulation of POPs, particularly highly hydrophobic ones, in the polar lipids of organisms will underestimate their concentrations at equilibrium.     

The binding of three PCB congeners to dissolved organic carbon in freshwaters

The binding of three polychlorinated biphenyl (PCB) congeners to natural levels of dissolved organic carbon (DOC) was measured in 12 lakes and streams using Sep-Pak C₁₈ columns. The association coefficients calculated on the basis of DOC (i.e. K_DOC mL/g C), varied by over an order of magnitude among the different freshwaters and ranged between 2.05 × 10² and 8.86 × 10³ mL/g C for PCB 52 and 1.03 × 10⁴ and 1.70 × 10⁵ mL/g C for PCB 153. In general, there were no significant correlations (p > 0.05) between the K_DOC values and various chemical parameters in the study lakes and streams.

A relationship was derived between the fraction of bound PCB and the octanol-water partition coefficient. While this relationship explained almost 50% of the variation in the observed data, it is apparent that other factors influence K_DOC values and that in natural freshwaters, only a small fraction of the DOC is involved in the binding of PCBs and other hydrophobic pollutants.     

Differential uptake for dioxin-like compounds by zucchini subspecies

The zucchini (Cucurbita pepo) cultivars 'Patty Green', 'Black Beauty', and 'Gold Rush' were cultivated on weathered dioxin-contaminated soil in pots, and concentrations of the 29 dioxin-like compounds that were assigned WHO-TEFs, three non-toxic polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), and two non-dioxin-like polychlorinated biphenyls (PCBs) were analyzed. Toxic equivalent (TEQ) values accumulated in 'Black Beauty' and 'Gold Rush' were about 180 times higher than those in 'Patty Green'. The bioconcentration factor (BCF) based on total mass concentration of the twelve dioxin-like PCBs was higher than those of the seven PCDDs and ten PCDFs in all the cultivars. The BCFs for PCDD and PCDF congeners were negatively correlated with octanol-water partition coefficients in all the plants. No correlations were observed in PCB congeners in the high accumulators, although in 'Patty Green' the BCFs for PCB congeners were significantly correlated with octanol-water partition coefficients. Our findings suggest that the high accumulators had unknown, unique mechanisms for uptake of PCBs, whereas PCDDs and PCDFs were absorbed based on their physicochemical properties.     

Modeling the partitioning of BTEX in water-reformulated gasoline systems containing ethanol

The objectives of this research were to quantify the extent of cosolvency for water–gasoline mixtures containing ethanol and to identify appropriate modeling tools for predicting the equilibrium partitioning of BTEX compounds and ethanol between an ethanol-bearing gasoline and water. Batch-equilibrium experiments were performed to measure ethanol and BTEX partitioning between a gasoline and aqueous phase. The experiments incorporated simple binary and multicomponent organic mixtures comprised of as many as eight compounds as well as highly complex commercial gasolines where the composition of the organic phase was not completely defined. At high ethanol volume fractions, the measured partition coefficients displayed an approximate linear relationship when plotted on semi-log scale as a function of ethanol volume fraction. At lower concentrations, however, there was a distinctly different trend which is attributed to a change in solubilization mechanisms at these concentrations. Three mathematical models were compared with or fit to the experimental results. Log-linear and UNIFAC-based models were used in a predictive capacity and were capable of representing the overall increase in partition coefficients as a function of increasing ethanol content in the aqueous phase. However, neither of these predicted the observed two-part curve. A piecewise model comprised of a linear relationship for low ethanol volume fractions and a log-linear model for higher concentrations was fit to data for a surrogate gasoline comprised of eight compounds and was then used to predict BTEX concentrations in the aqueous phase equilibrated with three different commercial gasolines. This model was superior to the UNIFAC predictions, especially at the low aqueous ethanol concentrations.     

Atmospheric concentrations and phase partitioning of polybrominated diphenyl ethers (PBDEs) in Izmir, Turkey

Atmospheric concentrations of 7 PBDE congeners (BDE-28, -47, -99, -100, -153, -154 and -209) were determined at four sites (i.e. Suburban, Urban 1, Urban 2, Industrial) in Izmir, Turkey and their gas/particle partitioning was investigated. Total PBDE ( summation operator(7)PBDE) concentrations ranged between 11 (Urban 1) and 149pgm(-3) (Industrial) in summer, while in winter, they ranged from 6 (Suburban) to 81pgm(-3) (Industrial). BDE-209 was the dominant congener at all sites, followed by BDE-99 and -47. Investigation of source profiles indicated that the air samples were dominated by congeners of the penta and deca-technical BDE mixtures. The measured PBDE particle fractions were compared to the predictions of the K(OA) (octanol-air partition coefficient)-based equilibrium partitioning model and to the dynamic uptake model developed by others for passive samplers, which was adapted to model gas-particle partitioning in this study. For BDE-28, good agreement was observed between the experimental particle fractions and those predicted by the equilibrium partitioning model. However, this model overestimated the particle fractions of other congeners. The predictions of the dynamic uptake model supported the hypothesis that the unexpectedly high partitioning of BDEs (except BDE-28) to the gas-phase is due to their departure from equilibrium partitioning. When congeners with very large octanol-air partition coefficients (i.e. BDE-100, -99, -154, -153, and -209) are emitted from their sources in the gas-phase, they may remain in that phase for several months before reaching equilibrium with atmospheric particles. This may also have important implications for the transport of atmospheric PBDEs. For example, in addition to particle-bound transport, the gas-phase transport of highly brominated congeners (i.e. BDE-209) may also be important.     

Octanol-solubility of dissolved and particulate trace metals in contaminated rivers: implications for metal reactivity and availability

The lipid-like, amphiphilic solvent, n-octanol, has been used to determine a hydrophobic fraction of dissolved and particulate trace metals (Al, Cd, Co, Cu, Mn, Ni, Pb, Zn) in contaminated rivers. In a sample from the River Clyde, southwest Scotland, octanol-solubility was detected for all dissolved metals except Co, with conditional octanol-water partition coefficients, D(ow), ranging from about 0.2 (Al and Cu) to 1.25 (Pb). In a sample taken from the River Mersey, northwest England, octanol-solubility was detected for dissolved Al and Pb, but only after sample aliquots had been spiked with individual ionic metal standards and equilibrated. Spiking of the River Clyde sample revealed competition among different metals for hydrophobic ligands. Metal displacement from hydrophobic complexes was generally most significant following the addition of ionic Al or Pb, although the addition of either of these metals had little effect on the octanol-solubility of the other. In both river water samples hydrophobic metals were detected on the suspended particles retained by filtration following their extraction in n-octanol. In general, particulate Cu and Zn (up to 40%) were most available, and Al, Co and Pb most resistant (<1%) to octanol extraction. Distribution coefficients defining the concentration ratio of octanol-soluble particle-bound metal to octanol-soluble dissolved metal were in the range 10(3.3)-10(5.3)mlg(-1). The presence of hydrophobic dissolved and particulate metal species has implications for our understanding of the biogeochemical behaviour of metals in aquatic environments. Specifically, such species are predicted to exhibit characteristics of non-polar organic contaminants, including the potential to penetrate the lipid bilayer. Current strategies for assessing the bioavailability and toxicity of dissolved and particulate trace metals in natural waters may, therefore, require revision.     

Soot-water distribution coefficients for polychlorinated dibenzo-p-dioxins,polychlorinated dibenzofurans and polybrominated diphenylethers determined with the soot cosolvency-column method

For many types of hydrophobic compounds, sorption non-linearity and solid-water distributions in the field well above expectations from organic matter partitioning models have lead to the proposition that strong adsorption to soot surfaces may not be limited to polycyclic aromatic hydrocarbons but may extend as a significant process for many aromatic compound classes. Here, the soot-water distribution coefficients (Ksc) were determined with the soot cosolvency-column method for homolog series of five polychlorinated dibenzo-p-dioxins (PCDDs), five polychlorinated dibenzofurans (PCDFs) and for two polybrominated diphenylethers (PBDEs). All compounds exhibited significantly stronger association with soot carbon than expected from estimates of their bulk organic-carbon normalized partition coefficients (Koc). The Ksc/Koc ratios (at aqueous concentrations of around 0.1-1 microg/l) were for PCDDs (up to tetrachlorination) 19-130 (median 25), for PCDFs (also up to tetrachlorination) 150-490 (median 300), and for both the tetra- and pentabrominated PBDEs a factor of 60. The particularly strong soot sorption for the PCDFs is of similar enhancement factors as previously elucidated for polycyclic aromatic hydrocarbons. Compound-class specific correlations between log Ksc and octanol-water partition coefficients (log Kow) were significant for both PCDDs and PCDFs (and with R2 > 98%). These may prove useful for anticipating variable fractions of dissolved exposures between different environmental regimes and putative remediation objects.     

PBDEs in leachates from municipal solid waste dumping sites in tropical Asian countries: phase distribution and debromination

Polybrominated diphenyl ethers (PBDEs) are extensively used as flame retardants in many consumer products, and leachates from landfills have been identified as one of the possible sources of PBDEs in the environment. Meanwhile, the unprecedented economic and population growths of some Asian countries over the last decade have led to significant increases in the amount of waste containing PBDEs in that region. This study investigates the status of PBDEs in leachates from municipal solid waste dumping sites (MSWDS) in tropical Asian countries. A total of 46 PBDE congeners were measured, both in the adsorbed (n?=?24) and dissolved (n?=?16) phases, in leachate samples collected, from 2002 to 2010, from ten MSWDS distributed among the eight countries of Lao PDR, Cambodia, Vietnam, India, Indonesia, Thailand, the Philippines, and Malaysia. PBDEs were predominantly found in the adsorbed phase. Partitioning of PBDEs in the dissolved phase was associated with the presence of dissolved organic matter; the apparent organic carbon-normalized partition coefficients (K′_oc) of the BDE congeners were lower by two to four orders of magnitude than the K _oc predicted from the octanol–water partition coefficients (K _ow). The total PBDE concentrations from mono- to deca-BDEs ranged from 3.7 to 133,000 ng/L, and showed a trend toward higher concentrations in the more populous and industrialized Asian countries. The congener profiles in the leachates basically reflected the composition of PBDE technical mixtures. The occurrence of congeners not contained, or in trace concentrations, in technical products (e.g., BDEs 208, 207, 206, 202, 188, 179, 49, 17/25, 8, 1) was observed in most of the leachate samples, suggesting the debromination of technical mixtures, including BDE-209, in the MSWDS of tropical Asian countries. Moreover, the temporal trend indicated the reduction of BDE-209 over time, with a corresponding increase in and/or emergence of lower brominated PBDE congeners. The results indicated that MSWDS of tropical Asian countries are potential sources of environmental PBDEs, which may be transported to the aquatic environment via dissolution with dissolved organic matter. MSWDS could be amplifiers of PBDE toxicity in the environment, possibly through debromination.     

Modelling PCB bioaccumulation in a Baltic food web

A steady state model is developed to describe the bioaccumulation of organic contaminants by 14 species in a Baltic food web including pelagic and benthic aquatic organisms. The model is used to study the bioaccumulation of five PCB congeners of different chlorination levels. The model predictions are evaluated against monitoring data for five of the species in the food web. Predicted concentrations are on average within a factor of two of measured concentrations. The model shows that all PCB congeners were biomagnified in the food web, which is consistent with observations. Sensitivity analysis reveals that the single most sensitive parameter is log K(OW). The most sensitive environmental parameter is the annual average temperature. Although not identified amongst the most sensitive input parameters, the dissolved concentration in water is believed to be important because of the uncertainty in its determination. The most sensitive organism-specific input parameters are the fractional respiration of species from the water column and sediment pore water, which are also difficult to determine. Parameters such as feeding rate, growth rate and lipid content of organism are only important at higher trophic levels.     

Dietary uptake kinetics of polychlorinated biphenyls from sediment-contaminated sandworms in a marine benthic fish (Pseudopleuronectes yokohamae)

To evaluate the dietary uptake of polychlorinated biphenyls (PCBs) from live food, we investigated the dietary uptake and depuration kinetics of PCBs in a marine benthic fish (marbled sole, Pseudopleuronectes yokohamae) by using as food live sandworms (Perinereis nuntia) that were laboratory-exposed to field-collected PCB-contaminated sediment. Marbled sole were fed the PCB-contaminated sandworms for 28 d and then uncontaminated sandworms for 56 d. The assimilation efficiencies (AEs) of 84 PCB congeners via the gastrointestinal tract (GIT) to the muscle of the fish ranged from 0.21 to 0.78; whole-body AEs would be lower than those of muscle because of the lower PCB concentrations, on a lipid basis. The AEs determined in this study were lower than those in other studies that used PCB-spiked commercial pelletized food. The lower AEs found in this study might be attributable to differences in the food administered (live sandworms vs. commercial pellet food), possibly because of low digestibility of sandworm lipids by marbled sole. In addition, the AEs in this study tended to increase with increasing log octanol-water partition coefficients (K_OW) up to about seven, although AEs in the other studies using commercial pelletized food did not increase with increasing log K_OW. This result suggests the co-transport of highly hydrophobic PCB congeners along with lipids and fatty acids from the digested sandworms into the GIT epithelium cells. The growth-corrected half-lives of 26 PCB congeners in the muscle of fish ranged from 20 to 107 d.     

Assessment of polychlorobiphenyls in human/poultry fat and in hair/plumage from a contaminated area

HR gas chromatographic PCB patterns in human/poultry fat tissue and hair/plumage in samples from a polluted region of Bela Krajina /Slovenia/ were investigated. The concentration of PCBs in human adipose tissue was found to be 9.62 μg/g in comparison to 0.67 μg/g in the adipose tissue of the non-exposed population, and in poultry fat 12.80 μg/g on a fat basis. The corresponding values in human hair and poultry plumage were 0.90 μg/g and 0.20 μg/g of original weight. The difference in PCB patterns between fat and hair can be attributed to the different routes of contamination (ingestion, air transport), to the time of exposure and physicochemical properties (octanol- water partition coefficients, Henry's law constants and the metabolism) of some individual congeners. Hair could be used for the assessment of ingestion of contaminated food and of the PCB levels in the air. In fat tissue PCB congeners with higher metabolic stability are enriched, whereas in hair PCB congeners with higher concentrations in air and with high octanol- water partition coefficients predominate.     

Modelling the dynamic air-water-sediment coupled fluxes and occurrence of polychlorinated biphenyls in a high altitude lake

The BIODEP model in terms of atmosphere-lake interactions was developed. The model was applied to an oligotrophic, dimictic high altitude lake (Lake Redo, Pyrenees) for a range of polychlorinated biphenyl (PCB) congeners. High altitude lakes, which receive their contaminant inputs uniquely from the atmosphere through long-range atmospheric transport, provide ideal controlled environments for the study of the interactions between atmospheric depositional and water column biogeochemical processes. The BIODEP model was able to predict dissolved water concentrations and PCB accumulation in the lake sediment within a factor of 2. This shows that the BIODEP model captures the essential processes driving the sink of POPs in high altitude lakes and that POP occurrence in the lake is driven by direct atmospheric inputs with limited influence from the watershed. An important seasonal variability in water column concentrations is predicted which should have important implications in sampling strategies. Furthermore, it is shown that diffusive air-water exchange dominated the PCB dynamics in the lake, especially for the less chlorinated biphenyls.     

Quantification of the dissolved organic matter effect on the sorption of hydrophobic organic pollutant: application of an overall mechanistic sorption model

This study presents an overall sorption model to estimate the sorption equilibrium coefficients of hydrophobic organic pollutants for heterogeneous aquatic systems. This proposed model combines a series of sorption equilibrium relationships including the adsorption of dissolved organic matters on particulates, the binding between organic pollutants and dissolved organic matters, and the sorption of organic pollutants on particulates with or without the presence of dissolved organic matters. By using this model, variations among the sorption equilibrium coefficients with the concentrations of dissolved organic matters are obtained. Also discussed herein are case studies involving pollutants having a wide spectrum of K(ow)s, different types of dissolved organic matters, different pH values and ionic strengths. In most of the case studies, the sorption equilibrium coefficients initially increase with the-concentrations of dissolved organic matters and, then, decrease after reaching a maximum value. This study also addresses the relative errors of partition coefficients attributed to the negligence of the effect caused by the dissolved organic matter, the so-called third-phase effect.     

Persistent organic pollutants in soil density fractions: distribution and sorption strength

The sorption strength of persistent organic pollutants in soils may vary among different soil organic matter (SOM) pools. We hypothesized that polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) were unevenly distributed and had different soil organic carbon (SOC)-water partition coefficients (K(OC)) among soil density fractions. We determined the concentrations and K(OC) values of 20 PAHs and 12 PCBs in bulk samples and three density fractions (light, <2.0, medium, 2.0-2.4, and heavy, >2.4 g cm(-3)) of 11 urban topsoils (0-5 cm) from Bayreuth, Germany. The K(OC) values were determined using sequential extraction with methanol-water mixtures (35% and 65% methanol) at 60 degrees C. The sum of 20 PAH concentrations in bulk soil ranged 0.4-186 mg kg(-1), and that of 12 PCB concentrations 1.2-158 microg kg(-1). The concentrations of all PAHs and PCBs decreased in the order light>medium>heavy fraction. When normalized to the SOC concentrations, PAH concentrations were significantly higher in the heavy than in the other density fractions. The K(OC) values of the PAHs in density fractions were 3-20 times higher than those of the PCBs with similar octanol-water partition coefficients (K(OW)). The K(OC) values of individual PAHs and PCBs varied up to a factor of 1000 among the studied soils and density fractions. The K(OC) values of 5- and 6-ring PAHs tended to be highest in the heavy fraction, coinciding with their enrichment in this fraction. For the other PAHs and all PCBs, the K(OC) values did not differ among the density fractions. Thus, there is no relationship between sorption strength and distribution among density fractions, indicating that density fractionation is not a suitable tool to distinguish among differently reactive PAH and PCB pools in soils.     

Use of semipermeable membrane devices (SPMDs)

Triolein-containing semipermeable membrane devices (SPMDs) were employed as passive samplers to provide data on the bioavailable fraction of organic, waterborne, organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs) and polynuclear aromatic hydrocarbons (PAHs) in streams flowing through a highly polluted industrial area of Bitterfeld in Saxony-Anhalt, Germany. The contamination of the region with organic pollutants originates in wastewater effluents from the chemical industry, from over one-hundred years of lignite exploitation, and from chemical waste dumps. The main objective was to characterise time-integrated levels of dissolved contaminants, to use them for identification of spatial trends of contamination, and their relationship to potential pollution sources. SPMDs were deployed for 43 days in the summer of 1998 at four sampling sites. The total concentration of pollutants at sampling sites was found to range from a low of 0.8 microgram/SPMD to 25 micrograms/SPMD for PAHs, and from 0.4 microgram/SPMD to 22 micrograms/SPMD for OCPs, respectively. None of the selected PCB congeners was present at quantifiable levels at any sampling site. A point source of water pollution with OCPs and PAHs was identified in the river system considering the total contaminant concentrations and the distribution of individual compounds accumulated by SPMDs at different sampling sites. SPMD-data was also used to estimate average ambient water concentrations of the contaminants at each field site and compared with concentrations measured in bulk water extracts. The truly dissolved or bioavailable portion of contaminants at different sampling sites ranged from 4% to 86% for the PAHs, and from 8% to 18% for the OCPs included in the estimation. The fraction of individual compounds found in the freely dissolved form can be attributed to the range of their hydrophobicity. In comparison with liquid/liquid extraction of water samples, the SPMD method is more suitable for an assessment of the background concentrations of hydrophobic organic contaminants because of substantially lower method quantification limits. Moreover, contaminant residues sequestered by the SPMDs represent an estimation of the dissolved or readily bioavailable concentration of hydrophobic contaminants in water, which is not provided by most analytical approaches.     

Distribution of polycyclic aromatic hydrocarbons in soil-water system containing a nonionic surfactant

The effect of a nonionic surfactant, Triton X-100 (TX100), on the distribution of four representative polycyclic aromatic hydrocarbons (PAHs), phenanthrene, fluorene, acenaphthene and naphthalene, in soil-water system was studied on a natural soil. The apparent soil-water distribution coefficient with surfactant (Kd*) for these compounds increased when TX100 equilibrium concentration from zero to around the critical micelle concentration (CMC), followed by a decrease in Kd* at TX100 equilibrium concentration greater than CMC. This is a direct result of surfactant sorption onto soil followed by PAHs partitioning to the sorbed surfactant. The values of carbon-normalized solute distribution coefficient (Kss) with the sorbed TX100 are greater than the corresponding partition coefficients with soil organic matter (Koc), which indicates the soil-sorbed nonionic surfactant is more effective per unit mass as a partitioning medium than the native soil organic matter for PAHs. When Kd* = Kd the corresponding initial concentration of surfactant was defined as critical washing concentration (CWC). Depending on the surfactant initial concentration below or above the CWC, the addition of nonionic surfactant can enhance the retardation of soil for PAHs or promote the removal of PAHs from soil, respectively. The values of Kd* and CWC can be predicted by a model, which correlates them with the compounds' octanol-water partition coefficients (Kow), soil property and the amount of soil-sorbed surfactant.     

Experimental verification of a model describing solid phase microextraction (SPME) of freely dissolved organic pollutants in sediment porewater

To verify a theoretical mass balance and multiple compartment partitioning model developed to predict freely dissolved concentrations (FDCs) of hydrophobic organic chemicals (HOCs) using negligible depletion-solid phase microextraction (nd-SPME), a series of sediment slurry experiments were performed using disposable poly(dimethyl)siloxane (PDMS) coated-SPME fibers and (14)C-radiolabeled HOC analogs. First, pre-calibration of disposable PDMS coated fibers for four model compounds (phenanthrene, PCB 52, PCB 153 and p,p'-DDE) with good precision (PCB 52>PCB 153, and the measured and predicted C(pw) values were not substantially different from empirically determined values except for p,p'-DDE.     

Regression method of the hydrophobicity ruler approach for determining octanol/water partition coefficients of very hydrophobic compounds

A regression method was developed for the hydrophobicity ruler approach, which is an indirect method for determining the octanol/water partition coefficients of very hydrophobic compounds. Two constants introduced into the mathematical model were obtained by regression of the absorption data sampled before the partition equilibrium. A water miscible organic solvent was used to increase the solubility of the very hydrophobic compounds in the aqueous solution so that the hydrophobicity scale was reduced and the equilibration was accelerated. Polydimethylsiloxane/methanol aqueous solution and a series of 21 polychlorinated biphenyls (PCBs) were used to demonstrate the regression method. The PCB compounds with known experimental logK(o/w) values served as reference compounds, while the PCB compounds without known logK(o/w) values were determined. The distribution coefficients (logK(p/s)), uptake and elimination rate constants were obtained from the two regression constants for each compound (reference or unknown). The correlation of the logK(p/s) values of the reference PCB compounds with their logK(o/w) values was linear (logK(o/w)=2.69logK(p/s)+0.76, R(2)=0.97). The logK(o/w) values were compared with literature values and suggested that some values from the literature far off the calibration line could be inaccurate. The critical experimental factors, the merits of the regression method were discussed.     

Chlorothalonil binding to aquatic humic substances assessed from gas purge studies

Abstract

Fate of the fungicide chlorothalonil (TCIN) binding to dissolved organic acid fractions was quantified using gas‐purge desorption studies. Binding studies were conducted to measure the dissolved organic carbon partition constant (K_DOC) with aquatic fulvic and humic acid fractions purified from cranberry bog water. Desorption studies at DOC concentrations up to 50 mg L^‐1 resulted in mean log K_DOC values of 4.63 (s.d.=0.5, n=8) and 4.81 (s.d.=0.7, n=7) for fulvic and humic acids, respectively. These values deviated from reported K_OC (organic carbon) values by 0.5 to 1.5 orders of magnitude. The relationship between K_OC and K_DOC did not conform to accepted ratios of 10: 1 to 3: 1, although these studies were conducted with the strong hydrophobic fraction of DOC. Binding was rapid suggesting hydrophobic partitioning or weak Van Der Waals forces as binding mechanisms. The strong binding potential for TCIN to aquatic humic substances corresponds to increased solubility in the aqueous system. Sorption to DOC suggests a possible transport mechanism which may result in elevated concentrations of TCIN in cranberry bog systems.     

Investigation of partitioning mechanism for volatile organic compounds in a multiphase system

Laboratory experiments were performed to investigate the partitioning behavior of a set of diverse volatile organic compounds (VOCs). After equilibration at a temperature of 25 °C, the VOC concentrations were measured by headspace method in combination with gas chromatography/mass spectrometry (GC/MS). The obtained data were used to determine the partition coefficients (K_P) of VOCs in a gas-liguid-solid system. The results have shown that the presence and nature of solid materials in the working solution control the air-water partitioning of dissolved VOCs. The air/solution partitioning of BTEX and C₉-C₁₀ aldehydes was most affected in the presence of diesel soot. K_P values decreased by a factor ranging from 1.5 for toluene to 3.0 for ethylbenzene. The addition of mineral dust in the working solution exhibited greater influence on the partitioning of short aldehydes. K_P values decreased by a factor of 1.8. The experimental partition coefficients were used to develop a predictive model for partitioning of BTEX and n-aldehydes between air, water and solid phases.