低频超声协同Fe-Ni-Mn／Al2O3催化降解酸性绿B的研究

采用低频超声与Fe-Ni-Mn／Al2O3催化剂协同降解偶氮染料酸性绿B模拟废水,考察染料初始浓度和pH值、催化剂、饱和气体及H2O2等因素对酸性绿B降解效果的影响,结果表明：催化剂Fe-Ni-Mn／Al2O3与低频超声存在协同效应,催化剂的最佳投加量为6g／L;酸性条件有利于染料的超声降解,当pH=3．8时,可取得最佳的降解效果;酸性绿B降解率随初始浓度的增大而降低,其优化初始浓度为100mg／L,此外,在反应体系中鼓入饱和气体也可促进酸性B的降解,且影响顺序为混合气体（air＋Ar）〉氧气〉氩气;在反应过程中投加H2O2有利于染料降解率的提高。在优化实验条件下降解150min,酸性绿B色度去除率达到91．4％。     

Cu-SBA-15催化湿式过氧化氢氧化水溶液中罗丹明B

采用水热晶化法合成了不同含铜量的Cu—SBA-15介孔分子筛,并且用XRD、N2吸附、TEM以及uV—vis对所合成的样品进行表征。以Cu—SBA-15为催化剂,H2O2为氧化剂,催化湿式过氧化水溶液中的罗丹明B,主要考察H2O2浓度、催化剂用量、处理温度、初始pH等因素对罗丹明B氧化效果的影响。结果表明,在同样的处理条件下罗丹明的脱色率明显高于TOC去除率,处理温度、初始pH对罗丹明B的脱色与氧化有重要影响。在罗丹明B初始浓度100mg／L,H2O2初始浓度1．8g／L,催化剂量0．3g／L,温度60℃,pH为7．0,处理时间100min时,罗丹明B的脱色率为98．6％,TOC去除率为62．8％。     

碱催化H2O2氧化法预处理奶牛养殖废水的试验研究

采用碱催化H2O2氧化法对奶牛养殖废水进行预处理试验,研究了温度、pH、H2O2投加量、反应时间等参数对COD去除效果的影响,确定了反应最佳运行条件。试验结果表明,碱催化H2O2氧化法在pH7~12时,对COD的去除率为40%~60%;当反应温度50℃,pH值9,H2O2投加量2.72 g/L,反应时间20 min时,COD的去除率为66.3%。     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

双频超声辐射协同H_2O_2降解偶氮染料废水的研究

采用双频超声协同H2O2降解酸性绿20染料废水,考察超声功率密度、染料初始浓度和pH、饱和气体及H2O2投加量等因素对酸性绿20降解效果的影响,结果表明,在给定实验条件下,双频降解效果优于单频超声波,且降解率随超声功率密度的增大而增大。酸性条件有利于酸性绿20的降解,当染料废水初始pH=4可取得最佳的降解效果;酸性绿20的降解效率随染料初始浓度的增大而降低,其优化初始浓度为40 mg/L。在反应体系中通入空气并投加H2O2,可取得最佳的降解效果。在优化实验条件下,采用双频超声协同H2O2降解5 h,酸性绿20的色度和TOC去除率分别为94.6%和36.3%;分析降解前后的紫外-可见光谱图可知,酸性绿20并非完全被降解为CO2和H2O,而是生成一些小分子有机中间体。     

鼓泡反应器中液相络合催化同时脱硫脱硝的研究

在鼓泡反应器中考察了[Co(en)3]2+同时吸收去除SO2和NO的影响因素,实验结果表明,pH值和脱硫剂种类是影响乙二胺合钴同时脱除NO和SO2的最重要影响因素,烟气中的氧促进乙二胺合钴吸收NO和SO2,烟气中的SO2,CO2和NO2对乙二胺合钴吸收NO具有抑制作用。在实验条件温度为20℃,pH为13.0,[Co(en)3]2+浓度为0.025 mol/L,加入1 g NH3.H2O的脱硝率更好,连续吸收60 min,脱硝率均保持在93.5%,加入NaOH和NH3.H2O的脱硫效果最好。乙二胺合钴络合同时脱除NO和SO2完全可以在一个装置中完成。     

响应面法优化UV／H2O2光氧化法处理高浓度LAS废水

采用响应面法对UV／H2O2光氧化法处理高浓度LAS废水的工艺参数进行了系统研究。根据Box—BehnkenDesign（BBD）设计原理,以初始pH与H2O2投加量、反应时间和温度为主要影响因素,设计4因素3水平共29个实验点的实验方案,并建立了二次响应面拟合模型。方差分析表明,初始pH与H2O2投加量、反应时间和温度以及初始pH和H2O2投加量、H2O2投加量和温度之间的交互作用,对实验结果具有显著性影响。实验得到的光氧化高浓度LAS废水最佳工艺条件,pH为4．0,H2O2投加量为40mmol／L,反应时间为90min,温度为25℃,在此条件下,LAS的平均去除率为98．1％。     

O3/H2O2工艺降解1,2,4-三氯苯的优化设计

考察用不同的氧化剂降解1,2,4-三氯苯（TCB）,3种不同方法对TCB的去除效果存在较大差别,其处理效果依次为：H2O2〈O3〈O3/H2O2。采用响应面法优化O3/H2O2工艺降解TCB的条件。结果表明,TCB初始浓度和H2O2投加量对TCB去除效果影响较大。TCB的降解符合准一级反应动力学规律,最佳降解条件为TCB初始浓度0.3 mg/L,pH=8.13,H2O2投加量0.40 mmol/L,O3转化率75%。在此条件下,TCB的平均去除率为91.5%,与预测值93.1%吻合度较高。     

A study on influential factors of high-phosphorus wastewater treated by electrocoagulation–ultrasound

A combined treatment of electrocoagulation and ultrasound was proposed to solve some problems which exist in the phosphorus removal processes in fine chemical industry. The intermittently discharged wastewater has the features of high initial phosphorus concentration and wide initial pH variation. The electrocoagulation–ultrasound effective performance for the removal of phosphorus was investigated. The results obtained from synthetic wastewater showed that the total phosphorus (TP) decreased from 86 to about 0.4 mg/L, and the removal efficiency reached about 99.6 %, when ultrasound was applied to the electrocoagulation cell under the optimum working conditions in 10 min. Comparatively, the TP removal efficiency of electrocoagulation group was 81.3 % and the ultrasound group has almost no change. Therefore, we can conclude that the electrocoagulation and ultrasound synergistic effect can effectively degrade high-phosphorus wastewater. We have discussed the impact of various parameters on the electrocoagulation–ultrasound based on the phosphorus removal efficiency. The results obtained from synthetic wastewater showed that the optimum working pH was found to be 6, allowing the effluent to be met the emission standards without pH adjustment. An increased current enhanced the speed of treatment significance, but higher current (>40 mA/cm²) enhanced ultrasonic cavitation effect causing flocculation ineffective. In addition, it was found that the optimum ultrasonic power was 4 W/cm² and the frequency was 20 kHz. The best ultrasound intervention and ultrasonic irradiation time were processed with electrocoagulation simultaneously. The results indicated that the electrocoagulation–ultrasound could be utilized as an attractive technique for removal of phosphate in the real wastewater.     

O3/H2O2处理嘧啶废水的研究

采用O3/H2O2法对嘧啶废水进行处理,考察了不同反应条件对嘧啶和COD去除率的影响,并对O3/H2O2降解嘧啶的反应机制和动力学进行了初步探讨。实验结果表明,在pH值为11,反应时间为70 min,O3流量为4 g/h,H2O2投加量为50 mmol/L的条件下,废水的嘧啶和COD的去除率分别达到86.46%和74.97%。嘧啶的去除率随自由基抑制剂叔丁醇增加而降低,说明O3/H2O2降解嘧啶主要为体系中.OH的贡献。同时动力学研究表明,O3/H2O2对嘧啶的降解符合一级反应动力学模型。     

High temperature dependence of 2,4-dichlorophenoxyacetic acid degradation by Fe3+/H(2)O(2) system

This study demonstrates the importance of reaction temperature on the degradation of 2,4-dichlorophenoxyacetic acid (2,4-D). In addition, we provide a mechanistic explanation for the temperature dependence of 2,4-D degradation. Thermal enhancement of 2,4-D degradation and H(2)O(2) decomposition was measured in the absence and in the presence of the z.rad;OH scavenger (t-butanol). The half-life for 2,4-D degradation was reduced by more than 70-fold in the absence of t-butanol, and by more than 700-fold, in the presence of t-butanol, when the reaction temperature was increased from 10 to 50 degrees C. In addition, similar temperature relationships were found for H(2)O(2) decomposition. The major reason for the high temperature dependence of the Fe(3+)/H(2)O(2) system in the case of 2,4-D degradation is due to the dependence of the initiation reaction of the Fe(3+)/H(2)O(2) system (i.e., Fe(3+)+H(2)O(2)-->Fe(2+)+HO(2)(z.rad;)+H(+) upon temperature), which is entirely consistent with the kinetics of the activation energy. In the presence of a z.rad;OH scavenger, the initiation reaction of the Fe(3+)/H(2)O(2) system became a determining factor of this temperature dependence, whereas in the absence of z.rad;OH scavenger, several other radical reactions played a role and this result in an apparent decrease in the activation energy for 2,4-D degradation. Moreover, the enhanced 2,4-D removal at higher temperatures did not alter H(2)O(2) utilization. The practical implications of the thermal enhancement of the Fe(3+)/H(2)O(2) system are discussed.     

Photooxidative removal of the herbicide Acid Blue 9 in the presence of hydrogen peroxide: modeling of the reaction for evaluation of electrical energy per order (E EO)

The present work deals with photooxidative removal of the herbicide, Acid Blue 9 (AB9), in water in the presence of hydrogen peroxide (H2O2) under UV light illumination (30 W). The influence of the basic operational parameters such as amount of H2O2, irradiation time and initial concentration of AB9 on the photodegradation efficiency of the herbicide was investigated. The degradation rate of AB9 was not appreciably high when the photolysis was carried out in the absence of H2O2 and it was negligible in the absence of UV light. The photooxidative removal of the herbicide was found to follow pseudo-first-order kinetic, and hence the figure-of-merit electrical energy per order (E Eo) was considered appropriate for estimating the electrical energy efficiency. A mathematical relation between the apparent reaction rate constant and H2O2 used was applied for prediction of the electricity consumption in the photooxidative removal of AB9. The results indicated that this kinetic model, based on the initial rates of degradation, provided good prediction of the E Eo values for a variety of conditions. The results also indicated that the UV/H2O2 process was appropriate as the effective treatment method for removal of AB9 from the contaminated wastewater.     

Replacement of H2O2 by O2 in Fenton and photo-Fenton reactions

The consumption of oxygen during the degradation of aniline by Fenton and photo-Fenton reactions is studied. The effect that parameters like aniline, Fe(II) and H2O2 initial concentration, pH, temperature and O2 flow rate have on the ratio O2 consumed/H2O2 consumed is examined. The determination of those combinations of experimental conditions for which an effective partial replacement of H2O2 by O2 as electron acceptor takes place is investigated. The results show that this replacement takes place in a variable extent, but the presence of H2O2 is necessary along the reaction, and the maximum consumption of O2 only takes place when the ratio amount of aniline mineralized vs. initial aniline concentration is minimal.     

TS-1分子筛催化O_3/H_2O_2氧化乙酸

研究了酸性条件下TS-1分子筛催化O3/H2O2体系（O3/H2O2/TS-1）对降解水中乙酸效率的影响,优化了相关工艺参数,并对其作用机理进行了分析。结果表明,在pH为2.8时,TS-1的加入能显著提高臭氧化的降解效率。优化工艺参数表明,当过氧化氢投加量为3 g/L,TS-1投加量为5 g/L时,O3/H2O2/TS-1体系对乙酸具有较高的降解率,60 min后O3/H2 O2/TS-1体系对乙酸（初始浓度为100 mg/L）的去除率达到了58.7%。当pH为0.8时,O3/H2 O2/TS-1体系对乙酸的去除率仅为19.8%,降解效果较差。定量化计算表明,O3/H2O2和O3/H2O2/TS-1的Rct分别为1.62×10-8和8.67×10-7。通过测定乙酸降解过程水样中过氧化氢和液相臭氧的浓度变化,推测了具体反应机理。由于此体系在酸性条件下对乙酸有较好的降解效果,拓宽了现有O3/H2O2体系的应用范围。     

TS-1分子筛催化O3/H2O2氧化乙酸

研究了酸性条件下TS-1分子筛催化O3/H2O2体系(O3/H2O2/TS-1)对降解水中乙酸效率的影响,优化了相关工艺参数,并对其作用机理进行了分析。结果表明,在pH为2.8时,TS-1的加入能显著提高臭氧化的降解效率。优化工艺参数表明,当过氧化氢投加量为3 g/L,TS-1投加量为5 g/L时,O3/H2O2/TS-1体系对乙酸具有较高的降解率,60 min后O3/H2 O2/TS-1体系对乙酸(初始浓度为100 mg/L)的去除率达到了58.7%。当pH为0.8时,O3/H2 O2/TS-1体系对乙酸的去除率仅为19.8%,降解效果较差。定量化计算表明,O3/H2O2和O3/H2O2/TS-1的Rct分别为1.62×10-8和8.67×10-7。通过测定乙酸降解过程水样中过氧化氢和液相臭氧的浓度变化,推测了具体反应机理。由于此体系在酸性条件下对乙酸有较好的降解效果,拓宽了现有O3/H2O2体系的应用范围。     

超声波/紫外线-Fenton反应联用去除克拉玛依土壤中石油类污染物

研究了超声波(ultrasonic)和紫外线(ultraviolet)-Fenton反应联用处理干旱区老化石油污染土壤。土壤TPH含量为30 470 mg/kg,pH值为3,H2O2与Fe比例为50∶1时,H2O2浓度为0.37%、0.74%、1.11%和1.85%在超声波处理6 h土壤TPH去除量分别为4 495、11 983、15 470和19 800 mg/kg;TPH去除量随H2O2/Fe2+增大而增大,H2O2/Fe2+为100∶1时,TPH去除量为12 699 mg/kg。溶液pH值接近中性,H2O2浓度为0.74%,H2O2/Fe2+为50∶1,超声波与UV共同作用2 h和4 h,TPH去除量分别达到14 824和21 821 mg/kg;UV单独作用2 h、4 h对土壤TPH去除量为9 253和12 845 mg/kg。超声波-Fenton反应对1,2-二甲苯降解效果最好,其次为C17-C28的直链及支链烷烃,最低为烃类衍生物。     

低频超声协同Fe-Ni-Mn/Al_2O_3催化降解酸性绿B的研究

采用低频超声与Fe-Ni-Mn/Al2O3催化剂协同降解偶氮染料酸性绿B模拟废水,考察染料初始浓度和pH值、催化剂、饱和气体及H2O2等因素对酸性绿B降解效果的影响,结果表明:催化剂Fe-Ni-Mn/Al2O3与低频超声存在协同效应,催化剂的最佳投加量为6 g/L;酸性条件有利于染料的超声降解,当pH=3.8时,可取得最佳的降解效果;酸性绿B降解率随初始浓度的增大而降低,其优化初始浓度为100 mg/L,此外,在反应体系中鼓入饱和气体也可促进酸性B的降解,且影响顺序为混合气体(air+Ar)>氧气>氩气;在反应过程中投加H2O2有利于染料降解率的提高.在优化实验条件下降解150 min,酸性绿B色度去除率达到91.4%.     

Color and COD removal from wastewater containing Reactive Black 5 using Fenton's oxidation process

In this study, Reactive Black 5 (RB5) was removed from synthetic wastewater using Fenton's oxidation (FO) process. Experiments were conducted on the samples containing 100 and 200 mg l(-1) of RB5 to remove the dye toxicity. Seventy-five milligram per litre of RB5 caused 25% toxicity on 24-h born daphnids whereas 100 mg l(-1) of RB5 displayed 100% toxicity on Daphnia magna. The study was performed in a systematic approach searching optimum values of FeSO(4) and H(2)O(2) concentrations, pH and temperature. Optimum pH and temperature for 100 mg l(-1) of RB5 were observed as 3.0 and 40 degrees C, respectively, using 100 mg l(-1) of FeSO(4) and 400 mg l(-1) of H(2)O(2) resulted in 71% chemical oxygen demand (COD) and 99% color removal. For 200 mg l(-1) of RB5, 84% COD removal was obtained using 225 mg l(-1) of FeSO(4) and 1000 mg l(-1) of H(2)O(2) yielding 0.05 molar ratio at pH 3.0 and 40 degrees C. Color removal was also more than 99%. The optimum conditions determined in accordance with the literature data. The H(2)O(2) requirement seems to be related to initial COD of the sample. FeSO(4)/H(2)O(2) ratios found were not changed for both concentrations. The temperature affected the COD removal significantly at high degrees. Toxicity was completely removed for each concentration of RB5 at optimum removal conditions.     

Atrazine removal by ozonation processes in surface waters

Atrazine (6-chloro-N-ethyl-N'-isopropyl-1,3,5-triazinedyl-2,4-diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continuously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O3/H2O2 process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O3/H2O2 and O3/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.