Converging hydrostatic and hydromechanic concepts of preferential flow definitions

The boundary between preferential flow and Richards-type flow is a priori set at a volumetric soil water content θ at which soil water diffusivity D (θ) = η (= 10^− 6 m² s^− 1), where η is the kinematic viscosity. First we estimated with a hydrostatic approach from soil water retention curves the boundary, θ^K, between the structural pore domain, in which preferential flow occurs, and the matrix pore domain, in which Richards-type flow occurs. We then compared θ^K with θ that was derived from the respective soil hydrological property functions of same soil sample. Second, from in situ investigations we determined 96 values of θ^G as the terminal soil water contents that established themselves when the corresponding water-content waves of preferential flow have practically ceased. We compared the frequency distribution of θ^G with the one of θ that was calculated from the respective soil hydrological property functions of 32 soil samples that were determined with pressure plate apparatuses in the laboratory. There is support of the notion that θ^K ≈ θ^G ≈ θ, thus indicating the potential of θ to explain more generally what constitutes preferential flow. However, the support is assessed as working hypothesis on which to base further research rather than a procedure to a clear-cut identification of preferential flow and associated flow paths.     

Impact of initial and boundary conditions on preferential flow

Preferential flow in soil is approached by a water-content wave, WCW, that proceeds downward from the ground surface. WCWs were obtained from sprinkler experiments with infiltration rates varying from 5 to 40 mm h^− 1. TDR-probes and tensiometers measured volumetric water contents θ(z,t) at seven depths, and capillary heads, h(z,t) at six depths in a column of an undisturbed soil. The wave is characterized by the velocity of the wetting front, c_W, the amplitude, w_S, and the final water content, θ. We tested with uni-variate and bi-variate linear regressions the impacts of initial volumetric water contents, θ_ini, and input rates, q_S, on c_W, w_S and θ.The test showed that θ_ini influenced θ and w_S and q_S effected c_W. The expected proportionality of w_S ≈ qs^1/3 was weak and c_W ≈ qs^2/3 was strong.     

Comparative studies of the Fe–UV, H2O2–UV, TiO2–UV/vis systems for the decolorization of a textile dye X-3B in water

The degradation of a common textile dye, Reactive-brilliant red X-3B, by several advanced oxidation technologies was studied in an air-saturated aqueous solution. The dye was resistant to the UV illumination (wavelength λ  320 nm), but was decolorized when one of Fe³⁺, H₂O₂ and TiO₂ components was present. The decolorization rate was observed to be quite different for each system, and the relative order evaluated under comparable conditions followed the order of Fe²⁺–H₂O₂–UV  Fe²⁺–H₂O₂ > Fe³⁺–H₂O₂–UV > Fe³⁺–H₂O₂ > Fe³⁺–TiO₂–UV > TiO₂–UV > Fe³⁺–UV > TiO₂–visible light (λ  450 nm) > H₂O₂–UV > Fe²⁺–UV. The mechanism for each process is discussed, and linked together for understanding the observed differences in reactivity.     

Oxidative properties of ambient PM2.5 and elemental composition: Heterogeneous associations in 19 European cities

We assessed the extent to which constituents of PM_2.5 (transition metals, sodium, chloride) contribute to the ability to generate hydroxyl radicals (OH) in vitro in PM_2.5 sampled at 20 locations in 19 European centres participating in the European Community Respiratory Health Survey. PM_2.5 samples (n = 716) were collected on filters over one year and the oxidative activity of particle suspensions obtained from these filters was then assessed by measuring their ability to generate OH in the presence of hydrogen peroxide. Associations between OH formation and the studied PM constituents were heterogeneous. The total explained variance ranged from 85% in Norwich to only 6% in Albacete. Among the 20 centres, 15 showed positive correlations between one or more of the measured transition metals (copper, iron, manganese, lead, vanadium and titanium) and OH formation. In 9 of 20 centres OH formation was negatively associated with chloride, and in 3 centres with sodium. Across 19 European cities, elements which explained the largest variations in OH formation were chloride, iron and sodium.     

Integration of traditional and innovative characterization techniques for flux-based assessment of Dense Non-aqueous Phase Liquid (DNAPL) sites

Key attributes of the source zone and the expanding dissolved plume at a trichloroethene (TCE) site in Australia were evaluated using trends in groundwater monitoring data along with data from on-line volatile organic compound (VOC) samplers and passive flux meters (PFMs) deployed in selected wells. These data indicate that: (1) residual TCE source mass in the saturated zone, estimated using two innovative techniques, is small ( 10 kg), which is also reflected in small source mass discharge ( 3 g/day); (2) the plume is disconnecting, based on TCE concentration contours and TCE fluxes in wells along a longitudinal transect; (3) there is minimal biodegradation, based on TCE mass discharge of  6 g/day at a plume control plane  175 m from source, which is also consistent with aerobic geochemical conditions observed in the plume; and (4) residual TCE in the vadose zone provides episodic inputs of TCE mass to the plume during infiltration/recharge events. TCE flux data also suggest that the small residual TCE source mass is present in the low-permeability zones, thus making source treatment difficult. Our analysis, based on a synthesis of the archived data and new data, suggests that source treatment is unwarranted, and that containment of the large TCE plume ( 1.2 km long,  0.3 km wide; 17 m deep;  2000–2500 kg TCE mass) or institutional controls, along with a long-term flux monitoring program, might be necessary. The flux-based site management approach outlined in this paper provides a novel way of looking beyond the complexities of groundwater contamination in heterogeneous domains, to make intelligent and informed site decisions based on strategic measurement of the appropriate metrics.     

A new approach to quantify the degradation kinetics of linuron with UV, ozonation and UV/O3 processes

The degradation of linuron, one of phenylurea herbicides, was investigated for its reaction kinetics by different treatment processes including ultraviolet irradiation (UV), ozonation (O₃), and UV/O₃. The decay rate of linuron by UV/O₃ process was found to be around 3.5 times and 2.5 times faster than sole-UV and ozone-alone, respectively. Experimental results also indicate overall rate constants increased exponentially with pH above 9.0 while the increase of rate constants with pH below 9 is insignificant in O₃ system. All dominant parameters involved in the three processes were determined in the assistant of proposed linear models in this study. The approach was found useful in predicting the process performances through the quantification of quantum yield (rate constant for the formation of free radical HOO⁻ from ozone decomposition at high pH), rate constant of linuron with ozone (k_O3,LNR), rate constant of linuron with hydroxyl radical (k_OH,LNR), and α (the ratio of the production rate of OH and the decay rate of ozone in UV/O₃ system).     

Simultaneous E. coli inactivation and NOM degradation in river water via photo-Fenton process at natural pH in solar CPC reactor. A new way for enhancing solar disinfection of natural water

Bacteria inactivation and natural organic matter oxidation in river water was simultaneously conducted via photo-Fenton reaction at “natural” pH (6.5) containing 0.6 mg L⁻¹ of Fe³⁺ and 10 mg L⁻¹ of H₂O₂. The experiments were carried out by using a solar compound parabolic collector on river water previously filtered by a slow sand filtration system and voluntarily spiked with Escherichia coli. Fifty five percent of 5.3 mg L⁻¹ of dissolved organic carbon was mineralized whereas total disinfection was observed without re-growth after 24 h in the dark.     

Evolution rates and PCB content of surface films that develop on impervious urban surfaces

Surface films on impervious surfaces mediate the fate of organic contaminants in urban areas. Using sheltered 3-mm diameter glass beads as a surrogate impervious urban surface, studies in downtown Toronto showed that surface films developed at a consistent rate of 1.6–2.6 nm day⁻¹. Linear film growth was observed up to and including the last day of three studies of 89-, 273-, and 84-day duration. Total PCB content (sum of 15 PCB congeners) also increased linearly, at a similar rate as the surface film. A complementary study using unsheltered beads showed that up to 80% of film mass and PCB content were removed by film wash-off during rain events. The film growth rate on beads exposed at a rural site, 200 km northeast of Toronto, was 12–20 times lower with PCB burdens that were 7–22 times lower compared to Toronto. Based on these findings, it is estimated that approximately 56–226 g of PCBs are captured by a 70 nm thick film covering just the horizontal surface area of Toronto. This is a substantial quantity of PCB that is available for rapid surface–air exchange and wash-off.     

Nature and prevalence of non-additive toxic effects in industrially relevant mixtures of organic chemicals

The concentration addition (CA) and the independent action (IA) models are widely used for predicting mixture toxicity based on its composition and individual component dose–response profiles. However, the prediction based on these models may be inaccurate due to interaction among mixture components. In this work, the nature and prevalence of non-additive effects were explored for binary, ternary and quaternary mixtures composed of hydrophobic organic compounds (HOCs). The toxicity of each individual component and mixture was determined using the Vibrio fischeri bioluminescence inhibition assay. For each combination of chemicals specified by the 2ⁿ factorial design, the percent deviation of the predicted toxic effect from the measured value was used to characterize mixtures as synergistic (positive deviation) and antagonistic (negative deviation). An arbitrary classification scheme was proposed based on the magnitude of deviation (d) as: additive (10%, class-I) and moderately (10 < d  30%, class-II), highly (30 < d  50%, class-III) and very highly (>50%, class-IV) antagonistic/synergistic. Naphthalene, n-butanol, o-xylene, catechol and p-cresol led to synergism in mixtures while 1, 2, 4-trimethylbenzene and 1, 3-dimethylnaphthalene contributed to antagonism. Most of the mixtures depicted additive or antagonistic effect. Synergism was prominent in some of the mixtures, such as, pulp and paper, textile dyes, and a mixture composed of polynuclear aromatic hydrocarbons. The organic chemical industry mixture depicted the highest abundance of antagonism and least synergism. Mixture toxicity was found to depend on partition coefficient, molecular connectivity index and relative concentration of the components.     

Coupled infrared extinction spectra and size distribution measurements for several non-clay components of mineral dust aerosol (quartz, calcite, and dolomite)

Simultaneous size distributions and Fourier transform infrared (FTIR) extinction spectra have been measured for several representative components of mineral dust aerosol (quartz, calcite, and dolomite) in the fine particle size mode (D=0.1–1 μm). Optical constants drawn from the published literature have been used in combination with the experimentally determined size distributions to simulate the extinction spectra. In general, Mie theory does not accurately reproduce the peak position or band shape for the prominent IR resonance features in the 800–1600 cm⁻¹ spectral range. The resonance peaks in the Mie simulation are consistently blue shifted relative to the experimental spectra by 20–50 cm⁻¹. Spectral simulations, derived from a simple Rayleigh-based analytic theory for a “continuous distribution of ellipsoids” particle shape model, better reproduce the experimental spectra, despite the fact that the Rayleigh approximation is not strictly satisfied in these experiments. These results differ from our previous studies of particle shape effects in silicate clay mineral dust aerosols where a disk-shaped model for the particles was found to be more appropriate.     

pH dependence of persulfate activation by EDTA/Fe(III) for degradation of trichloroethylene

The ability of free ferrous ion activated persulfate (S₂O₈²⁻) to generate sulfate radicals (SO₄⁻) for the oxidation of trichloroethylene (TCE) is limited by the scavenging of SO₄⁻ with excess Fe²⁺ and a quick conversion of Fe²⁺ to Fe³⁺. This study investigated the applicability of ethylene-diamine-tetra-acetic acid (EDTA) chelated Fe³⁺ in activating persulfate for the destruction of TCE in aqueous phase under pH 3, 7 and 10. Fe³⁺ and EDTA alone did not appreciably degrade persulfate. The presence of TCE in the EDTA/Fe³⁺ activated persulfate system can induce faster persulfate and EDTA degradation due to iron recycling to activate persulfate under a higher pH condition. Increasing the pH leads to increases in pseudo-first-order-rate constants for TCE, S₂O₈²⁻ and EDTA degradations, and Cl generation. Accordingly, the experiments at pH 10 with different EDTA/Fe³⁺ molar ratios indicated that a 1/1 ratio resulted in a remarkably higher degradation rate at the early stage of reaction as compared to results by other ratios. Higher persulfate dosage under the EDTA/Fe³⁺ molar ratio of 1/1 resulted in greater TCE degradation rates. However, increases in persulfate concentration may also lead to an increase in the rate of persulfate consumption.     

Ten years of atmospheric methane observations at a high elevation site in Western China

In this paper, the continuous (1994–2001) and discrete air sample (1991–2001) measurements of atmospheric CH₄ from the Waliguan Baseline Observatory located in western China (36°17′N, 100°54′E, 3816 m asl) are presented and characterized. The CH₄ time series show large episodic events on the order of 100 ppb throughout the year. During spring, a diurnal cycle with average amplitude of 7 ppb and a morning maximum and late afternoon minimum is observed. In winter, a diurnal cycle with average amplitude of 14 ppb is observed with an afternoon maximum and morning minimum. Unlike most terrestrial observational sites, no obvious diurnal patterns are present during the summer or autumn. A background data selection procedure was developed based on local horizontal and vertical winds. A selected hourly data set representative of “baseline” conditions was derived with approximately 50% of the valid hourly data. The range of CH₄ mixing ratios, annual means, annual increases and mean annual cycle at Waliguan during the 1992–2001 were derived from discrete and continuous data representative of “baseline” conditions and compared to air samples collected at other Northern Hemisphere sites. The range of CH₄ monthly means of 1746–1822 ppb, average annual means of 1786.7±10.8 ppb and mean annual increase of 4.5±4.2 ppb yr⁻¹ at Waliguan were inline with measurements from sites located between 30° and 60°N. There were variations observed in the CH₄ annual increase patterns at Waliguan that were slightly different from the global pattern. The mean CH₄ annual cycle at Waliguan shows an unusual pattern of two gentle peaks in summer and February along with two small valleys in early winter and spring and a mean peak-to-peak amplitude of 11 ppb, much smaller than amplitudes observed at most other mid- and high-northern latitude sites. The Waliguan CH₄ data are strongly influenced by continental Asian CH₄ emissions and provide key information for global atmospheric CH₄ models.     

Gas/particle partitioning of atmospheric PCDD/Fs in a satellite town in Eastern China

Gas/particle partitioning of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in ambient air was investigated in a satellite town in Eastern China from April 2007 to January 2008 comprehending large temperature variations (from 3 to 34 °C, daily average). Molecular weight, molecular structure and ambient temperatures are the three major factors that govern the gas/particle partitioning of atmospheric PCDD/Fs throughout the year. Generally, good agreements were obtained (except for winter) between measured particulate fractions and theoretical estimates of both the Junge–Pankow adsorption model and Harner Bidleman absorption model using different sets of subcooled liquid vapor pressure and octanol–air partition coefficient (K_oa), respectively. Models utilizing estimates, derived from gas chromatographic retention indices (GC-RIs), are more accurate than that of entropy-based. Moreover, during winter, the K_oa-based model using the GC-RIs approach performs better on lower chlorinated PCDD/Fs than that of -based. Furthermore, possible sources of mismatch between measured and predicted values in winter (3–7 °C) were discussed. Gas adsorption artifact was demonstrated to be of minor importance for the phenomena observed. On the other hand, large deviations of slopes (m_r) and intercepts (b_r) in logK_p vs. plots from theoretical values are observed in the literature data and these are found to be linearly correlated with ambient temperatures (P<0.001) in this study. This indicates that the non-equilibrium partitioning of PCDD/Fs in winter may be significantly influenced by the colder temperatures that may have slowed down the exchange between gaseous and particulate fractions.     

Removal of toxic ions (chromate, arsenate, and perchlorate) using reverse osmosis, nanofiltration, and ultrafiltration membranes

Rejection characteristics of chromate, arsenate, and perchlorate were examined for one reverse osmosis (RO, LFC-1), two nanofiltration (NF, ESNA, and MX07), and one ultrafiltration (UF and GM) membranes that are commercially available. A bench-scale cross-flow flat-sheet filtration system was employed to determine the toxic ion rejection and the membrane flux. Both model and natural waters were used to prepare chromate, arsenate, and perchlorate solutions (approximately 100 μg L⁻¹ for each anion) in mixtures in the presence of other salts (KCl, K₂SO₄, and CaCl₂); and at varying pH conditions (4, 6, 8, and 10) and solution conductivities (30, 60, and 115 mS m⁻¹). The rejection of target ions by the membranes increases with increasing solution pH due to the increasingly negative membrane charge with synthetic model waters. Cr(VI), As(V), and rejection follows the order LFC-1 (>90%) > MX07 (25–95%)  ESNA (30–90%) > GM (3–47%) at all pH conditions. In contrast, the rejection of target ions by the membranes decreases with increasing solution conductivity due to the decreasingly negative membrane charge. Cr(VI), As(V), and rejection follows the order CaCl₂ < KCl  K₂SO₄ at constant pH and conductivity conditions for the NF and UF membranes tested. For natural waters the LFC-1 RO membrane with a small pore size (0.34 nm) had a significantly greater rejection for those target anions (>90%) excluding (71–74%) than the ESNA NF membrane (11–56%) with a relatively large pore size (0.44 nm), indicating that size exclusion is at least partially responsible for the rejection. The ratio of solute radius (r_i,s) to effective membrane pore radius (r_p) was employed to compare ion rejection. For all of the ions, the rejection is higher than 70% when the r_i,s/r_p ratio is greater than 0.4 for the LFC-1 membrane, while for di-valent ions (, , and ) the rejection (38–56%) is fairly proportional to the r_i,s/r_p ratio (0.32–0.62) for the ESNA membrane.     

Degradation of acetic acid with sulfate radical generated by persulfate ions photolysis

The photolysis of was studied for the removal of acetic acid in aqueous solution and compared with the H₂O₂/UV system. The radicals generated from the UV irradiation of ions yield a greater mineralization of acetic acid than the OH radicals. Acetic acid is oxidized by radicals without significant formation of intermediate by-products. Increasing system pH results in the formation of OH radicals from radicals. Maximum acetic acid degradation occurred at pH 5. The results suggest that above this pH, competitive reactions with the carbon mineralized inhibit the reaction of the solute with and also OH radicals. Scavenging effects of two naturally occurring ions were tested; in contrast to ions, the presence of Cl⁻ ions enhances the efficiency of the /UV process towards the acetate removal. It is attributed to the formation of the Cl radical and its great reactivity towards acetate.     

Simulation of aerosol radiative properties with the ORISAM-RAD model during a pollution event (ESCOMPTE 2001)

The aim of this study is to present the organic and inorganic spectral aerosol module-radiative (ORISAM-RAD) module, allowing the 3D distribution of aerosol radiative properties (aerosol optical depth, single scattering albedo and asymmetry parameter) from the ORISAM module. In this work, we test ORISAM-RAD for one selected day (24th June) during the ESCOMPTE (expérience sur site pour contraindre les modèles de pollution atmosphérique et de transport d’emissions) experiment for an urban/industrial aerosol type. The particle radiative properties obtained from in situ and AERONET observations are used to validate our simulations. In a first time, simulations obtained from ORISAM-RAD indicate high aerosol optical depth (AOD)0.50–0.70±0.02 (at 440 nm) in the aerosol pollution plume, slightly lower (10–20%) than AERONET retrievals. In a second time, simulations of the single scattering albedo (ω_o) have been found to well reproduce the high spatial heterogeneities observed over this domain. Concerning the asymmetry parameter (g), ORISAM-RAD simulations reveal quite uniform values over the whole ESCOMPTE domain, comprised between 0.61±0.01 and 0.65±0.01 (at 440 nm), in excellent agreement with ground based in situ measurements and AERONET retrievals. Finally, the outputs of ORISAM-RAD have been used in a radiative transfer model in order to simulate the diurnal direct radiative forcing at different locations (urban, industrial and rural). We show that anthropogenic aerosols strongly decrease surface solar radiation, with diurnal mean surface forcings comprised between −29.0±2.9 and −38.6±3.9 W m⁻², depending on the sites. This decrease is due to the reflection of solar radiations back to space (−7.3±0.8<ΔF_TOA<−12.3±1.2 W m⁻²) and to its absorption into the aerosol layer (21.1±2.1<ΔF_ATM<26.3±2.6 W m⁻²). These values are found to be consistent with those measured at local scale.     

The Danish eulerian hemispheric model — a three-dimensional air pollution model used for the arctic

A three-dimensional Eulerian hemispheric air pollution model, the Danish Eulerian Hemispheric Model (DEHM), is in development at the National Environmental Research Institute (NERI). The model has been used to study long-range transport of air pollution in the Northern Hemisphere. The present version of the model includes long-range transport of sulphur dioxide (SO₂) and particulate sulphate (SC₄²⁻. The chemistry in the model is described by a simple linear oxidation of SO₂ to SO₄²⁻, and the wet deposition of SO₂ and SO₄⁻ is estimated based on the amount of precipitation, which is calculated from the contents of liquid cloud water (see Christensen, Air Pollution Modelling and its Applicatioons, Vol. X, pp. 119–127, Vol. XI, pp. 249–256, Plenum press, New York; 1995, Ph.D. thesis, National Environmental Research Institute, Denmark). The model has been used to study the air pollution in the Arctic. Results from yr simulation with an analysis of the results is presented: the model results are verified by comparisons, to measurements not only from the Arctic region but also from Europe and Canada. Some examples of episodes in the Arctic including analysis of the meteorological conditions during the episodes are presented. Finally, the model has been used to estimate the contribution from the different source regions on the northern hemisphere to the Arctic sulphur pollution.     

Assessment and optimisation of VOC mass transfer enhancement by advanced oxidation process in a compact wet scrubber

Dimethyl disulphide (DMDS) removal was investigated in a compact scrubber (hydraulic residence time ≈20 ms), composed of a wire mesh packing structure where liquid and gas flow at co-current and high gas superficial velocity (>12 m s⁻¹). In order to regenerate the scrubbing liquid and to maintain a driving force in the scrubber, ozone and hydrogen peroxide were added to water since they allow the generation of nonselective and highly reactive species, hydroxyl radicals HO. Three ways of reagent distribution were tested. The influence of several parameters (liquid flow rate(s), ozone flow rate, pH and reagent concentrations) was investigated. The best configuration was obtained when ozone is transferred in the scrubbing liquid before introduction at the top of the scrubber simultaneously with the hydrogen peroxide solution, allowing to generate hydroxyl radical in the scrubber. With this configuration, DMDS removal could be increased from 16% with water to 34% at the same gas and liquid flow rates in the scrubber showing the potentiality of advanced oxidation process.