Maize tassel-modified carbon paste electrode for voltammetric determination of Cu(II)

The preparation and application of a practical electrochemical sensor for environmental monitoring and assessment of heavy metal ions in samples is a subject of considerable interest. In this paper, a carbon paste electrode modified with maize tassel for the determination of Cu(II) has been proposed. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) were used to study morphology and identify the functional groups on the modified electrode, respectively. First, Cu(II) was adsorbed on the carbon paste electrode surface at open circuit and voltammetric techniques were used to investigate the electrochemical performances of the sensor. The electrochemical sensor showed an excellent electrocatalytic activity towards Cu(II) at pH 5.0 and by increasing the amount of maize tassel biomass, a maximum response at 1:2.5 (maize tassel:carbon paste; w/w) was obtained. The electrocatalytic redox current of Cu(II) showed a linear response in the range (1.23 μM to 0.4 mM) with the correlation coefficient of 0.9980. The limit of detection and current–concentration sensitivity were calculated to be 0.13 (±0.01) μM and 0.012 (±0.001) μA/μM, respectively. The sensor gave good recovery of Cu(II) in the range from 96.0 to 98.0 % when applied to water samples.     

水样品中汞砷联合测定的研究--氢化物发生原子荧光光谱法

利用氢化物发生-原子荧光分析技术(HG-AFS)对水样品中汞、砷联合测定方法进行了有益的探索.通过一系列条件实验,设定出了合理有效的水样前处理方法、仪器测定条件以及主要试剂的浓度.并对其最低检出下限、精密度和准确度进行了评估,结果表明该方法用于环境水样品中汞、砷元素的同时测定具有很好的可行性和适用性.     

气动进样原子荧光法测定环境水样中痕量汞和砷

以硼氢化钾作为还原剂原子荧光法测定环境水样中的汞和砷,配合以气动进样,方法简单、试剂用量少、灵敏度高.测汞时KBH4-KOH浓度为0.01%～0.0005%,样品中王水浓度3%(v/v),检测限为5.8×10-3μg/L;测砷时KBH4-KOH浓度为2.6%～1.0%,样品中盐酸浓度5%(v/v),检测限为4.9μg/L.     

Voltammetric determination of platinum at a lead film electrode in environmental water samples

The paper presents the first report on the application of a lead film electrode for the determination of ultratrace concentrations of platinum. The procedure is based on preconcentration of the Pt(IV)-formaldehyde complexes at an in situ plated lead film electrode held at ?0.9 V (vs. Ag/AgCl), followed by a negatively sweeping differential pulse voltammetric scan. The composition of the supporting electrolyte, the influence of accumulation potential and time on the sensitivity of platinum responses are discussed. The detection limit of Pt(IV) with the accumulation time of 60 was equal to 9.2?×?10^?12 mol L^?1. The application of this method was tested by recovery of Pt(IV) from spiked environmental water samples.     

Simultaneous determination of selected endocrine disrupter compounds in wastewater samples in ultra trace levels using HPLC-ES-MS/MS

An analytical procedure for the simultaneous determination of six selected endocrine disrupter compounds (EDCs: diltiazem, progesterone, benzyl butyl phthalate (BBP), estrone, carbamazepine (Cbz), acetaminophen) was developed by liquid chromatography electrospray ionization tandem mass spectrometry (HPLC-ES-MS/MS). All of the parameters for HPLC and ES-MS/MS systems including mobile phase composition, flow rate, and sample injection volume were optimized to obtain not only the best separation of species interested but also low detection limits. Reverse phase chromatography coupled to ES-MS/MS was used for the separation and detection of EDCs. Formic acid (0.10% ) and 5.0 mM ammonium formate were selected as mobile phase composition in gradient elution. Detection limits for diltiazem, progesterone, BBP, estrone, Cbz, and acetaminophen were found to be 0.13, 0.12, 0.04, 0.13, 0.12, and 0.05 ng/mL, respectively. Influent and effluents from three different wastewater treatment plants located in Ankara, i.e., rotating flat-sheet membrane unit, pilot type flat-sheet membrane unit located at METU Campus and samples from Ankara central wastewater treatment plant were analyzed for their EDCs contents under the optimum conditions.     

导数示波极谱法测定废水中微量的对硝基乙苯

研究了导数示波极谱法测定废水中微量的对硝基乙苯的方法.在0.0150mol/L乙二胺-0.0100mol/L EDTA底液中,对硝基乙苯产生一灵敏的二阶导数极谱峰,峰电位为-0.54V(Vs·SCE).对硝基乙苯浓度在1.00×10-7～7.00×10-5mol/L范围内,浓度与峰电流成线性关系.检测限为1.00×10-7mol/L.本方法可用于废水中微量对硝基乙苯的测定.     

Remediation aspect of microbial changes of plant rhizosphere in mercury contaminated soil

Phytoremediation, an approach that uses plants to remediate contaminated soil through degradation, stabilization or accumulation, may provide an efficient solution to some mercury contamination problems. This paper presents growth chamber experiments that tested the ability of plant species to stabilize mercury in soil. Several indigenous herbaceous species and Salix viminalis were grown in soil collected from a mercury-contaminated site in southern Poland. The uptake and distribution of mercury by these plants were investigated, and the growth and vitality of the plants through a part of one vegetative cycle were assessed. The highest concentrations of mercury were found at the roots, but translocation to the aerial part also occurred. Most of the plant species tested displayed good growth on mercury contaminated soil and sustained a rich microbial population in the rhizosphere. The microbial populations of root-free soil and rhizosphere soil from all species were also examined. An inverse correlation between the number of sulfur amino acid decomposing bacteria and root mercury content was observed. These results indicate the potential for using some species of plants to treat mercury contaminated soil through stabilization rather than extraction. The present investigation proposes a practical cost-effective temporary solution for phytostabilization of soil with moderate mercury contamination as well as the basis for plant selection.     

Separation and determination of trace levels of aromatic amines by HPLC

Aromatic amines were analysed by normal phase and reverse phase high performance liquid chromatography employing silica gel and octadecyl silane (ODS) columns, respectively. A number of mobile phases were used. The results obtained on silica gel column were compared with those achieved on reverse phase column. Excellent results were obtained on ODS and shoulder peaks were eliminated when a mixture of methyl alcohol and sodium perchlorate was used as mobile phase.     

多元配合物胶束增溶光度法测定微量氰化物

根据CN-对丁二酮肟-Ni-OP-10体系的增色作用,建立了一种测定微量氰化物的新方法.该方法操作简便,选择性好,不需要蒸馏和萃取.CN-量在0～5μg/25ml内符合比尔定律,用于环境水中氰化物的测定,结果满意.     

燃煤电厂烟气中汞的采集与分析方法

汞的测试技术包括采样和分析两部分,其中汞含量的分析方法已经相对比较成熟,限制测试技术发展的诸多问题主要来源于取样过程。根据不同的取样方式,将现有测试技术分为湿式采样分析法、干式采样分析法以及在线分析技术3种,重点介绍了3种方法的采样原理、系统构成、过程的影响因素以及适用范围。最后针对CVAAS、CVAFS、AES 3种汞含量测定技术在Hg CEMS测试系统中的应用进行了对比介绍。     

A simple extraction procedure for determination of total mercury in crude oil

The determination of mercury in crude oil and petroleum products is particularly difficult due to the volatile nature of both mercury and the matrix, which may lead to significant loss of the analyte. A simple extraction method for total mercury has been developed to determine total mercury in crude oil using cold vapor atomic fluorescence spectrometry. The homogenized crude oil sample was diluted to 5, 10, and 20 % (w/w) in toluene. The diluted crude oil samples were spiked with 10 and 40 μg/kg (w/w). The samples were extracted using an oxidant/acid solution, BrCl/HCl. The mercury was extracted into the aqueous phase; the ionic mercury was then reduced to volatile elemental mercury (Hg⁰) by stannous chloride (SnCl₂). The mercury vapor was detected by Merlin cold vapor atomic fluorescence spectrometry at a 253.7-nm wavelength. The average recoveries for mercury in spiked diluted crude oil (10 and 40 μg/kg, w/w) were between 96 and 103 %, respectively, in 5 and 10 % spiked diluted crude oil. Whereas, low recoveries (<50 %) were recorded in 20 % diluted spiked crude oil. The method detection limit was calculated as t _{(0.01)(n ? 1)}?×?SD where t is the student's value for 99 % confidence level and standard deviation estimate with n???1 degrees of freedom. The method detection limit was found to be 0.38 μg/kg based on 5 g of diluted crude oil sample. The method is sensitive enough to determine low levels of mercury in crude oil.     

Influence of mercury from fly ash on cattle reared nearby thermal power plant

Cattle grazing nearby coal-fired power stations are exposed to fly ash. The present investigation aims to assess the environmental and health impacts of fly ash containing mercury emitted from thermal power plant. The health effect of fly ash were studied using 20 lactating cattle reared within a 5-km radius of s thermal power plant for the possible effect of fly ash such as the alterations in hematological and biochemical parameters of blood, milk, and urine. Results indicated that the hemoglobin levels (6.65?±?0.40?g/dl) were significantly reduced in all the exposed animals. Biochemical parameters viz., blood urea nitrogen (27.35?±?1.19?mg/dl), serum glutamate oxaloacetate transaminase (43.39?±?3.08?IU/l), albumin, and creatinine were found to be increased, whereas serum glutamate pyruvic transaminase (29.26?±?2.02) and Ca²⁺ were observed to be statistically insignificant in exposed animals. Mercury concentrations estimated in the blood, milk, and urine of exposed (n?=?20) and control (n?=?20) animals were 7.41?±?0.86, 4.75?±?0.57, 2.08?±?0.18, and 1.05?±?0.07, 0.54?±?0.03, 0.20?±?0.02?μg/kg, respectively. The significant increase (P?<?0.01) in the levels of mercury in blood, milk, and urine of exposed animals in comparison to control indicated that the alterations of biochemical parameters in exposed cattle could be due to their long term exposure to fly ash mercury which may have direct or indirect impact on human populations via food chain.     

石墨炉原子吸收光谱法测定土壤中的微量砷

土壤样品经ＨＮＯ３－ＨＣＩＯ４消解处理后,采用Ｎｉ作为基体改进剂,偏振塞曼效应扣去背景,实现了砷的石墨炉原子吸收法的直接测定。该方法操作简单,干扰少,灵敏度高,砷的检测下限为０．７ｎｇ／ｍｌ,样品分析回收率９４％－１０８％,相对标准偏差５．１％。     

示波极谱法测定大气总悬浮微粒中微量锌

在乙二胺 (en)介质中 (p H1 1 .5～ 1 2 .3 ) ,Zn(en) 2 +3在单扫描示波极谱仪上于 -1 .42 V(vs.SCE)处产生一灵敏的络合物吸附波 ,锌含量在 0 .0 0 6～ 0 .3 5 μg/ml范围内 ,浓度与峰电流呈线性关系。检测限为 0 .0 0 3 μg/ml。加标回收率为92 %～ 1 0 3 % ,相对标准偏差小于 4.1 %。该方法准确、简便、选择性好 ,可用于 TSP中微量锌的测定。     

Preconcentration of Zn2+ and Cu2+ ions from food and vegetable samples using modified activated carbon

In this work, two N/S-containing chelating agents 2-(4-methoxybenzylideneamino)thiophenol (2-4-MBAT) and 2-(4-chlorobenzylideneamino) benzenethiol (2-4-CBABT) were synthesized as new sorbents and were used for preconcentration of Zn(2+) and Cu(2+) ions in food and vegetable samples. In the proposed procedure, the trace amount of Zn(2+) and Cu(2+) ions from 250?mL of sample solution at pH?=?5.0 was preconcentrated by 1?g of activated carbon (AC) loaded with 15?mg of 2-4-MBAT and 2-4-CBABT separately. The breakthrough volumes (maximum sample volume that their metal ions quantitatively can be enriched) for solid-phase extraction (SPE) procedure based on the AC modified with 2-4-MBAT and 2-4-CBABT were 800 and 750?mL, respectively. The sorbed Zn(2+) and Cu(2+) ions were efficiently eluted by 8?mL of 4?mol?L(-1) HNO(3) and preconcentration factor of 112.5 and 93.7 and experimental enhancement factor of 30 and 35 ions were obtained for Zn(2+) and Cu(2+), respectively. The application of this enrichment procedure allowed the extraction of trace metal ions with recoveries exceeding of 90%.     

Simultaneous spectrophotometric determination of trace amount of polycyclic aromatic hydrocarbons in water samples after magnetic solid-phase extraction by using projection pursuit regression

Magnetic solid-phase extraction based on coated nano-magnets Fe₃O₄ was applied for the preconcentration of four polycyclic aromatic hydrocarbons (PAHs; anthracene, phenanthrene, fluorine, and pyrene) in environmental water samples prior to simultaneous spectrophotometric determination using multivariate calibration method. Magnetic nanoparticles, carrying target metals, were easily separated from the aqueous solution by applying an external magnetic field so, no filtration or centrifugation was necessary. After elution of the adsorbed PAHs, the concentration of PAHs was determined spectrophotometrically with the aid of a new and efficient multivariate spectral analysis base on principal component analysis-projection pursuit regression, without separation of analytes. The obtained results revealed that using projection pursuit regression as a flexible modeling approach improves the predictive quality of the developed models compared with partial least squares and least squares support vector machine methods. The method was used to determine four PAHs in environmental water samples.     

Spectrophotometeric determination of trace amounts of Al3+ ion in water samples after cloud point extraction using quinizarin as a complexing agent

In this study, cloud point extraction was used for the preconcentration of Al³⁺ ion after the complex formation with 1,4-dihydroxy-9,10-anthraquinone (Quinizarin [QUIN]), and subsequent analysis by spectrophotometeric method, using Triton X-114 as surfactant. The optimal extraction and reaction conditions were studied (i.e., pH?=?5.5, 0.1 mM QUIN, Triton X-114?=?0.1 % (w/v)), and the analytical characteristics of the method (e.g., limit of detection, linear range, preconcentration, and enrichment factors) were obtained. Linearity was obeyed in the range of 3.33–166.67 ng ml^?1 of Al³⁺ ion. The detection limit of the method was 2.09 ng ml^?1 for Al³⁺ ion. The interference effect of some anions and cations was also tested. The method was applied to determine Al³⁺ ion in water samples.     

Methods for determination of elemental carbon in ambient air

A few analytical methods of elemental carbon determination are described. The purpose of the work is to choose the best method for determination of its content in dust suspended in air in industrial regions. The reflectance and chromatographic methods were investigated. It was shown that the reflectance methods could be used only when the particle size and form of elemental carbons constant. The chromatographic method, which includes the step of combustion of the sample in oxygen and chromatographic determination of evolved CO₂ is recommended, since it is independent of the form of carbon. Organic carbon is removed from dust samples by extraction with benzene-methanol mixture.     

Environmental applications of ICP-MS for simultaneous determination of trace elements and statistical data analysis

Water samples collected from two lakes separated from each other by the cascade of four small lowland reservoirs were subjected to analyses in order to compare contamination levels in these ecosystems. Inductively coupled plasma mass spectrometry was used to determine eight elements: Al, As, Cd, Cr, Li, Mn, Sb, and Zn. Statistical methods were applied in order to assess the degree of self-purification of water, during its flow from Swarz?dzkie Lake to Malta Lake. Obtained distinctly, lower concentrations of all studied elements in Malta Lake than in Swarz?dzkie Lake indicated the role of self-purification processes, which occurred in the distance between these lakes.     

Preconcentration technique for the determination of trace elements in natural water samples by ICP-AES

A procedure was developed for the determination of Cd, Cu, Zn, Co, Ni, Mn, Pb and Mo in water samples by inductively coupled plasma atomic emission spectrometry (ICP-AES) after preconcentration on a morpholine dithiocarbamate (mor-DTC) supported by bagasse (Saccharam aphisinaram). The sorbed elements were subsequently eluted with 4,M HNO₃ and the acid eluates were analysed by ICP–AES. The influence of various parameters such as pH, flow rate of sample, eluent concentration, volume of the sample and volume of eluent were investigated to enhance the sensitivity of the present method. A 20,mL disposable syringe served as preconcentration column. Under the optimal conditions Cd, Cu, Zn, Co, Ni, Mn, Pb and Mo in aqueous sample was concentrated about 100-fold. The sorption recoveries of elements were higher than 99.6%. The method is also applied for the analysis of natural and spiked water samples.