Reference values for heavy metals in soils of the Brazilian agricultural frontier in Southwestern Amazônia

Guideline values are used to identify polluted or contaminated areas based on background values. Brazilian law establishes three guideline values for pollutants: a quality reference value (QRV), a prevention value, and an intervention value. Reference values refer to the natural concentration of an element or a substance in soils that have not been modified by anthropogenic impacts. These values inform assessments of soil quality and are used to establish maximum permissible limits. The objective of this study was to determine the natural levels and reference values for Cd, Co, Cr, Cu, Ni, Pb, and Zn in samples from the surface layer (0–20 cm) of 19 representative soils of the states of Mato Grosso and Rondônia, on Brazil’s agricultural frontier. Pseudo-total metal concentrations were obtained following microwave-assisted digestion using the aqua regia and EPA3051 methods. QRVs were calculated for each element as the 75th and 90th percentiles of the frequency distribution of the data. Natural levels of heavy metals in the soil samples followed the order: Cr?>?Zn?>?Cu?>?Co?>?Pb?>?Ni?>?and Cd (aqua regia) and Cr?>?Co?>?Cu?>?Pb?>?Zn?>?Ni?>?Cd (EPA3051). These values are generally lower than those reported in the Brazilian and international literature, which highlights the importance of establishing reference values for each state or for each soil type, taking into account the geomorphological, pedological, and geological diversity of the region under study.     

Geochemical fractionation of trace elements in sediments of Hugli River (Ganges) and Sundarban wetland (West Bengal, India)

A sequential extraction procedure was carried out to determinate the concentrations of 11 elements (Al, As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn) in different geochemical phases of sediments collected along the Hugli (Ganges) River Estuary and in the Sundarban mangrove wetland, eastern coastal part of India. The chemical speciation of elements was determined using the three-step sequential extraction procedure described by the European Community Bureau of Reference. Total metal concentration was determined using a microwave-assisted acid digestion procedure. Metal concentrations were near the background level except for As for which a moderate pollution can be hypothesized. The mobility order of the metals was: Cd?>?Mn?>?Cu?>?Zn?>?As?>?Co?>?Pb?>?Ni?>?Fe?>?Cr?>?Al. The highest percentage of Cd (>60%) was found in the most labile phase. Residual fraction was prevailing for Fe, Cr and Al, while Pb was mainly associated with the reducible fraction. Data were compared with Sediment Quality Guidelines to estimate the relationship between element concentrations and adverse biological effects on benthic community, finding the possibility of some toxic effects due to the presence of As in the entire studied area and Cd, only in Calcutta.     

Vertical distribution of heavy metals in soil profile in a seasonally waterlogging agriculture field in Eastern Ganges Basin

The accumulation of heavy metals in soil and water is a serious concern due to their persistence and toxicity. This study investigated the vertical distribution of heavy metals, possible sources and their relation with soil texture in a soil profile from seasonally waterlogged agriculture fields of Eastern Ganges basin. Fifteen samples were collected at ～0.90-m interval during drilling of 13.11 mbgl and analysed for physical parameters (moisture content and grain size parameters: sand, silt, clay ratio) and heavy metals (Fe, Mn, Cr, Cu, Pb, Zn, Co, Ni and Cd). The average metal content was in the decreasing order of Fe?>?Mn?>?Cr?>?Zn?>?Ni?>?Cu?>?Co?>?Pb?>?Cd. Vertical distribution of Fe, Mn, Zn and Ni shows more or less similar trends, and clay zone records high concentration of heavy metals. The enrichment of heavy metals in clay zone with alkaline pH strongly implies that the heavy metal distributions in the study site are effectively regulated by soil texture and reductive dissolution of Fe and Mn oxy-hydroxides. Correlation coefficient analysis indicates that most of the metals correlate with Fe, Mn and soil texture (clay and silt). Soil quality assessment was carried out using geoaccumulation index (I _geo), enrichment factor (EF) and contamination factor (CF). The enrichment factor values were ranged between 0.66 (Mn) and 2.34 (Co) for the studied metals, and the contamination factor values varied between 0.79 (Mn) and 2.55 (Co). Results suggest that the elements such as Cu and Co are categorized as moderate to moderately severe contamination, which are further confirmed by I _geo values (0.69 for Cu and 0.78 for Co). The concentration of Ni exceeded the effects-range median values, and the biological adverse effect of this metal is 87 %. The average concentration of heavy metals was compared with published data such as concentration of heavy metals in Ganga River sediments, Ganga Delta sediments and upper continental crust (UCC), which apparently revealed that heavy metals such as Fe, Mn, Cr, Pb, Zn and Cd are influenced by the dynamic nature of flood plain deposits. Agricultural practice and domestic sewage are also influenced on the heavy metal content in the study area.     

Application of a modified BCR sequential extraction (three-step) procedure for the determination of extractable trace metal contents in a sewage sludge amended soil reference material (CRM 483), complemented by a three-year stability study of acetic acid and EDTA extractable metal content

This paper provides additional data on a sewage sludge amended soil certified reference material, CRM 483, which was certified in 1997 for its EDTA and acetic acid extractable contents of some trace metals, following standardised extraction procedures. The additional work aimed to test the long-term stability of the material and the applicability of an improved version of the BCR three-step sequential extraction procedure on the sewage sludge amended soil (CRM 483). The paper demonstrates the CRM 483 long-term stability for EDTA and acetic acid extractable contents of Cd, Cr, Cu, Ni, Pb and Zn and gives the results (obtained in the framework of an interlaboratory study) for the extractable contents of the same elements in the CRM 483, following the BCR three-step sequential extraction scheme. The aqua regia extractable contents following the ISO 11466 Standard are also given. The data are given as indicative (not certified) values.     

Total and available heavy metal concentrations in soils of the Thriassio plain (Greece) and assessment of soil pollution indexes

The Thriassio plain is located 25 km west of Athens city, the capital of Greece. Two major towns (Elefsina and Aspropyrgos), heavy industry plants, medium to large-scale manufacturing, logistics plants, and agriculture comprise the main land uses of the studied area. The aim of the present study was to measure the total and available concentrations of Cr, Zn, Ni, Pb, Co, Mn, Ba, Cu, and Fe in the top soils of the plain, and to asses soil contamination by these metals by using the geoaccumulation index (I _geo), the enrichment factor (EF), and the availability ratio (AR) as soil pollution indexes. Soil samples were collected from 90 sampling sites, and aqua regia and DTPA extractions were carried out to determine total and available metal forms, respectively. Median total Cr, Zn, Ni, Pb, Co, Mn, Ba, Cu, and Fe concentrations were 78, 155, 81, 112, 24, 321, 834, 38, and 16?×?10³ mg?kg^?1, respectively. The available fractions showed much lower values with medians of 0.4, 5.6, 1.7, 6.9, 0.8, 5.7, 19.8, 2.1, and 2.9 mg?kg^?1. Though median total metal concentrations are not considered as particularly high, the I _geo and the EF values indicate moderate to heavy soil enrichment. For certain metals such as Cr, Ni, Cu, and Ba, the different distribution patterns between the EFs and the ARs suggest different origin of the total and the available metal forms. The evaluation of the EF and AR data sets for the soils of the two towns further supports the argument that the EFs can well demonstrate the long-term history of soil pollution and that the ARs can adequately portray the recent history of soil pollution.     

Atmospheric deposition studies of heavy metals in Arctic by comparative analysis of lichens and cryoconite

Lichens and cryoconite (rounded or granular, brownish-black debris occurring in holes on the glacier surface) from Ny-Ålesund were used for understanding the elemental deposition pattern in the area. Lichen samples collected from low-lying coastal region and cryoconite samples from high altitudinal glacier area were processed and analysed for elements such as aluminium (Al), arsenic (As), cadmium (Cd), cobalt (Co), chromium (Cr), cesium (Cs), copper (Cu), iron (Fe), manganese (Mn), nickel (Ni), lead (Pb), vanadium (V) and zinc (Zn) through inductively coupled plasma mass spectrometry. Results showed that heavy metals, Al and Fe, are present in high concentration in the cryoconite samples. Al was also present in high amounts in seven of the eight lichen samples studied. The general scheme of elements in the decreasing order of their concentrations for most of the cryoconite samples was Al?>?Fe?>?Mn?>?Zn?>?V?>?Pb?>?Cr?>?Ni?>?Cu?>?Co?>?As?>?Cs?>?Cd while that for the lichen samples was Al?>?Fe?>?Zn?>?Mn?>?Pb?>?Cu?>?Cs?>?Cr?>?Ni?>?V?>?Co?>?As?>?Cd. Similarity in trends in the two sample types confirms that the environment indeed contains these elements in that order of concentration which overtime got accumulated in the samples. Overall comparison showed most elements to be present in high concentrations in the cryoconite samples as compared to the lichen samples. Within the lichens, elemental accumulation data suggests that the low-lying site (L-2) from where Cladonia mediterranea sample was collected was the most polluted accumulating a number of elements at high concentrations. The probable reasons for such deposition patterns in the region could be natural (crustal contribution and sea salt spray) and anthropogenic (local and long-distance transmission of dust particles). In the future, this data can form a baseline for monitoring quantum of atmospheric heavy metal deposition in lichens and cryoconite of Svalbard, Arctic.     

Determination of total and EDTA extractable metal distributions in the colloidal fraction of contaminated soils using SdFFF-ICP-HRMS

Newly developed methods involving an on-line combination of sedimentation field-flow fractionation-inductively coupled plasma-high resolution mass spectrometry (SdFFF-ICP-HRMS) have been used to study the distributions of extractable heavy metals in a soil which had been treated with sewage sludge contaminated with Cu or Pb. The relationship of these metals with other elements in the colloidal fraction was also investigated. The colloidal fraction from the soil was obtained by repeated gravitational sedimentation and extracted with 0.11 M acetic acid, 0.1 M hydroxylamine hydrochloride, 0.05 M ethylenediaminetetraacetic acid disodium salt (EDTA) or aqua regia to assess the potential availability of the metals Cu and Pb. Large proportions of the Cu and Pb were extracted by EDTA, approaching that removed by aqua regia, whereas < 10% of the aqua regia extractable metals were removed by acetic acid and hydroxylamine chloride. The distributions of the heavy metals, the major mineral forming element (Al) and the elements forming sesquioxides (Fe and Mn) within different size classes (0.05-1 microm) of the colloidal fraction were measured using SdFFF-ICP-HRMS before and after extraction with EDTA. This information provides an insight into the composition of the colloids and the distributions of metal contaminants. In the contaminated soil colloids, the concentration of Fe, Mn and Pb is greatest in the smaller particles (<0.2 microm). In contrast, the Cu concentration is constant over the size range studied. Iron oxide surface coatings probably play a significant role in Pb adsorption on soil particles, but may be less important for Cu. The combination of selective chemical extraction, SdFFF and ICP-HRMS provides a means of determining the distribution of potentially available heavy metals within the colloidal fraction of contaminated soils.     

Metallic components of traffic-induced urban aerosol, their spatial variation, and source apportionment

This study proposes a practical method to estimate elemental composition and distribution in order to attribute source and quantify impacts of aerosol particles at an urban region in Kolkata, India. Twelve-hour total particulates were collected in winter (2005–2006) and analyzed by energy-dispersive X-ray fluorescence technique to determine multi-elemental composition, especially trace metals. The aerosols consist of various elements including K, Ca, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Se, and Pb which exhibit significant concentration at various sites (p?<?0.05). The concentration of different metallic elements were found in the order of Zn ?> ?Pb ?> ?Ni ?> ?Cu ?> ?Cr ?>? Co. Statistical multivariate analysis and correlation matrix analyses were performed for factor identification and consequent source apportionment. Contour profiles demonstrate spatial variation of elemental compositions indicating possible source contribution along with meteorological influences. Spatial differences were clearly most significant for Zn, Ni, Pb, and Cu reflecting the importance of anthropogenic inputs, primarily from automobile sources.     

Trace element concentration and speciation in selected urban soils in New York City

A long history of urbanization and industrialization has affected trace elements in New York City (NYC) soils. Selected NYC pedons were analyzed by aqua regia microwave digestion and sequential chemical extraction as follows: water soluble (WS); exchangeable (EX); specifically sorbed/carbonate bound (SS/CAR); oxide-bound (OX); organic/sulfide bound (OM/S). Soils showed a range in properties (e.g., pH 3.9 to 7.4). Sum of total extractable (SUM_TE) trace elements was higher in NYC parks compared to Bronx River watershed sites. NYC surface horizons showed higher total extractable (TE) levels compared to US non-anthropogenic soils. TE levels increased over 10 year in some of the relatively undisturbed and mostly wooded park sites. Surface horizons of park sites with long-term anthropogenic inputs showed elevated TE levels vs. subsurface horizons. Conversely, some Bronx River watershed soils showed increased concentrations with depth, reflective of their formation in a thick mantle of construction debris increasing with depth and intermingled with anthrotransported soil materials. Short-range variability was evident in primary pedons and satellite samples (e.g., Pb 253?±?143 mg/kg). Long-range variability was indicated by Pb_TE (348 versus 156 mg/kg) and Hg_TE (1 versus 0.3 mg/kg) concentrations varying several-fold in the same soil but in different geographic locations. Relative predominance of fractions: RES (37 %)?>?SS/CAR (22 %)?>?OX (20 %)?>?OM/S (10 %)?>?EX (7 %)?>?WS (4 %). WS and EX fractions were greatest for Hg (7 %) and Cd (14 %), respectively. RES was predominant fraction for Co, Cr, Ni, and Zn (41 to 51 %); SS/CAR for Cd and Pb (40 and 63 %); OM/S for Cu and Hg (36 and 37 %); and OX for As (59 %).     

Fractions and background concentrations of potentially toxic elements in Hungarian surface soils

This work established background concentrations for the pseudo total (HNO₃ + H₂O₂-soluble), mobilisable (NH₄-acetate + EDTA-soluble) and mobile (1?M NH₄NO₃-soluble) element fractions of Hungarian surface soils that can be used as reference values for the soil quality standards. The 193 soils investigated were taken from the Hungarian Soil Information and Monitoring System. The background values for Al, As, B, Cd, Co, Cr, Cu, Mn, Ni, Pb, Sr and Zn were given as a range covering 95% of the variance of the representative samples. The differences between observed element concentrations and the calculated background values indicated anthropogenic or pedogenic impact in each fraction. The comparison of the calculated background values with the Hungarian quality standards and the contamination limit values of other countries showed that the limit values of a certain region or country are not suitable for other areas. Generally, Mn and Al had the highest, while Cd had the lowest concentration in each fraction. Cr and Al were the least and Sr was the most mobile element. The principal component analysis indicated different geochemical and physico-chemical behaviour of the elements in the fractions; the pseudo total fraction was influenced more by the geological behaviour, while mobilisable and mobile fraction explained a much higher proportion of the total variance of soil physico-chemical properties than soil geochemical properties. The Cd–Ni and Co–Mn element pairs were always in the same principal component in each fractions indicating similar geogenic origin and showing that their solubility changes are similar in function of soil properties.     

Metal release from serpentine soils in Sri Lanka

Ultramafic rocks and their related soils (i.e., serpentine soils) are non-anthropogenic sources of metal contamination. Elevated concentrations of metals released from these soils into the surrounding areas and groundwater have ecological-, agricultural-, and human health-related consequences. Here we report the geochemistry of four different serpentine soil localities in Sri Lanka by coupling interpretations garnered from physicochemical properties and chemical extractions. Both Ni and Mn demonstrate appreciable release in water from the Ussangoda soils compared to the other three localities, with Ni and Mn metal release increasing with increasing ionic strengths at all sites. Sequential extraction experiments, utilized to identify “elemental pools,” indicate that Mn is mainly associated with oxides/(oxy)hydroxides, whereas Ni and Cr are bound in silicates and spinels. Nickel was the most bioavailable metal compared to Mn and Cr in all four soils, with the highest value observed in the Ussangoda soil at 168?±?6.40 mg kg^?1 via the 0.01-M CaCl₂ extraction. Although Mn is dominantly bound in oxides/(oxy)hydroxides, Mn is widely dispersed with concentrations reaching as high as 391 mg kg^?1 (Yudhaganawa) in the organic fraction and 49 mg kg^?1 (Ussangoda) in the exchangeable fraction. Despite Cr being primarily retained in the residual fraction, the second largest pool of Cr was in the organic matter fraction (693 mg kg^?1 in the Yudhaganawa soil). Overall, our results support that serpentine soils in Sri Lanka offer a highly labile source of metals to the critical zone.     

Certification of the extractable contents of Cd, Cr, Cu, Ni, Pb and Zn in a freshwater sediment following a collaboratively tested and optimised three-step sequential extraction procedure

Sequential extraction procedures have been used during the last decades to study and determine trace element mobility in aquatic sediments. However, the results obtained are operationally defined and, therefore, the significance of the analytical results is related to the extraction scheme used. So, there is a need for suitable reference materials for this type of study to enable the validation of the methodologies and to control the quality of the measurements. This paper describes the preparation of a sediment reference material, BCR-701, the homogeneity and stability studies and the analytical work performed for the certification of the extractable contents of some trace elements, following a collaboratively tested and optimised sequential (three-step) extraction procedure. The paper contains all the results and gives the methods used to certify the extractable contents (mass fractions expressed as mg kg-1 on a dry matter basis) of Cd, Cr, Cu, Ni, Pb and Zn in all steps. Moreover, indicative values are given for the aqua regia extractable contents of the six elements in the sediment and the residue obtained after sequential extraction.     

Speciation and ecological risk of heavy metals in intertidal sediments of Quanzhou Bay, China

The chemical speciation of nine heavy metals in intertidal sediments from Quanzhou Bay was determined using a modified sequential extraction procedure, proposed by the Commission of the European Community Bureau of Reference. The results show that Mn presents the highest percentage in the acid-soluble fraction, and Pb and Cu present the highest percentages in the reducible fraction. The highest percentages of Fe, V, Cr, Ni, Zn, and Co were found in the residual fraction. The mobility order of the heavy metals studied on the basis of the nonresidual content of the elements is Mn > Pb > Cu > Co > Zn > Ni > Cr > V > Fe. The assessment on potential ecological risk indices of some heavy metals indicates that Zn, Ni, and Cr show moderate contamination, while Cu and Pb show slighter contamination. On the whole, the comprehensive potential ecological risk index of Cu, Zn, Ni, Cr, and Pb in the sediments presents moderate degree.     

Statistical characteristics of selected elements in vegetables from Kosovo

Zinc, copper, iron, chromium and cobalt are essential elements for human health, showing toxicity only in high concentrations, while lead and cadmium are extremely toxic even as traces. Therefore, it is important to monitor the contents of toxic metals in vegetables. Large number of vegetables is grown and used in nutrition, in Kosovo. The concentrations of selected elements in vegetables (radish, onion, garlic and spinach) from Kosovo were determined using ICP-OES method. Oral intake of metals and health risk index were calculated. Statistical analysis indicated numerous positive correlations between concentrations of selected elements in vegetables. As a result of principal component analysis, 15 new variables were obtained which were characterized by eigenvalues. The sequence of health quotients for the heavy metals followed the decreasing order Zn?=?Mn?>?Pb?>?Cu?>?Ni?>?Fe?>?Cd?>?Co?>?Cr. The health quotients for all investigated heavy metals were below 1 (one), which is considered safe. The vegetables from Kosovo are mainly safe for use in everyday diet.     

Heavy metals in urban ambient PM10 and soil background in eight cities around China

The ambient PM₁₀ and background soil samples were collected and analyzed with ICP-AES in eight cities around China to investigate the levels of ten heavy metals (Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, and Pb). The mean concentrations of ten heavy metals in PM₁₀ of the eight cities of China followed the order of Zn?>?Pb?>?Mn?>?Cu?>?Ni?>?Cr?>?Co?>?V. The metals in the ambient PM₁₀ and soil were compared in each city to evaluate the heavy metal mass fraction from anthropogenic sources in ambient air. The CD values in these cities were all above 0.2, indicating that the ingredients spectrums of PM₁₀ and soil vary markedly. Most heavy metals were enriched in PM₁₀, except Fe and Ti. The results showed that almost all the cities suffer important heavy metal pollution from anthropogenic sources. The eight cities were also grouped according to their similarity in heavy metals of ambient PM₁₀ by cluster analysis to investigate the relationship between the heavy metals and the pollution sources of each city. The conclusion was that the eight cities were divided into three clusters which had similar industrial type and economy scale: the first cluster consisted of Shenzhen, Wuxi, and Guiyang; followed by Jinan and Zhengzhou as the second grouping; and the third group had Taiyuan, Urumqi, and Luoyang.     

Assessment of background levels of trace metals in water and soil from a remote region of Himalaya

Selected trace metals were estimated by atomic absorption spectrometry in the water and soil samples collected from the remote region of Himalaya. The soil samples were analysed for soluble and acid extractable fraction of trace metals. In water samples, Ca, Na, Mg and K emerged as dominant contributors, whereas, Ca, Na, K, Mg, Fe and Pb were estimated at comparatively higher levels in the water extract of the soil. In case of acid extract of the soil samples, Ca, K, Fe, Mg, Mn and Na were found at elevated concentrations. Based on mean levels of the metals, following decreasing concentration order was observed in water samples: Ca > Na > Mg > K > Pb > Co > Cu > Zn > Mn > Cr > Fe > Cd > Li, however, in the acid extract of the soil, following order was noted: Ca > K > Fe > Mg > Mn > Na > Pb > Zn > Cr > Li > Cu > Co > Cd. The correlation study revealed appreciably diverse mutual relationships of trace metals in the water and soil samples. The multivariate cluster analyses exhibited divergent apportionment of trace metals in water and soil samples. Among the trace metals, Cd, Pb, Li, Zn, Cr, Cu, Mn and Co exhibited extreme to significant anthropogenic enrichment in the soil samples, while the rest of the metals were mostly contributed by the natural processes.     

Total concentrations, fractionation and mobility of heavy metals in soils of urban area of Guwahati, India

This work describes the results of assessment of the heavy metals, Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn in urban soil of Guwahati City, India from 31 sites of five different land use types covering residential, commercial, industrial, public utilities, and roadside. Sequential extraction procedure was used to evaluate the relative distribution of the eight metals in exchangeable, carbonate, reducible (Fe?CMn oxide), organic and sulfide, and residual fractions. Of the eight metals, Cd and Co occur in lower concentrations (Cd <?< Co) in all types of land, and concentration variation from one type of land use to another is not much significant for both the metals. Ni presence is more than Co, and the concentrations show some variation depending on land use status. Average Cr and Cu concentrations are ??100?mg/kg, but Cr has a significantly higher presence in industrial land use. The results are similar in case of Pb. The two metals, Mn and Zn have domination over the other metals, and the values are ??300?mg/kg. Industrial and roadside soil contains much more Mn, while commercial soil is most enriched with Zn. Of the metals, Ni has the largest proportion (~42%) bound to the exchangeable fraction and Co, Cr, and Pb also have appreciable proportion bound to the same fraction. A significant amount of Co is associated with carbonates. The reducible fraction has bound considerable quantity of Mn and Zn, while most of Cu is associated with the organic and sulfide fraction. Both Cd and Pb are dominantly associated with the residual fraction. Computation of the mobility factor of the metals indicates Mn to be the most mobile metal present in the soil samples.     

The determination of the extractability of selected elements from agricultural soil

Concentrations of Ag, Al, Ba, Cd, Co, Cr, Cu, Fe, K, Mn, Na, Ni, Pb, Sr, and Zn—isolated by sequential extraction steps from apple orchard soil—were analyzed by inductively coupled plasma-atomic emission spectroscopy and compared to the total amount of metal in soil determined by XRF. The extractable amount of each metal was calculated by the extraction yields of the four steps. The LODs of the different elements in all extracts ware below 3 μg/L except for Ba (steps 1 and 2), Cu (step 1), Fe (all steps), K (steps 1–3), Mn (step 2), Na (steps 1–3), Ni (step 1), Pb (steps 1 and 4), and Zn (steps 1 and 2). The highest LOD (>10 μg/L) was found for Fe, K, and Na (step 1). The recovery of all metals after four sequential extraction steps was 90–112%. The repeatability (<1.1%), the intermediate precision (<5.3%), the day-to-day reproducibility (<6.2%), and the overall uncertainty of measurement (approximately 4–8.5%) for all analyzed metals supports the choice of the method used.     

Chemical fractionation of heavy metals in urban soils of Guangzhou, China

Knowledge of the total concentration of heavy metals is not enough to fully assess the environmental impact of urban soils. For this reason, the determination of metal speciation is important to evaluate their environment and the mobilization capacity. Sequential extraction technique proposed by the former European Community Bureau of Reference (BCR) was used to speciate Cd, Cu, Fe, Mn, Ni, Pb, and Zn in urban soils from Guangzhou into four operationally defined fractions: HOAc extractable, reducible, oxidizable, and residual. The Cu, Fe, Ni, and Zn were predominately located in the residual fraction, Pb in the reducible fraction, and Cd and Mn within the HOAc extractable fraction. The order of Cd in each fraction was generally HOAc extractable > reducible > residual > oxidizable; Cu and Fe were residual > reducible > oxidizable > HOAc extractable; Mn was HOAc extractable > residual > reducible > oxidizable; Ni and Zn were residual > reducible > HOAc extractable > oxidizable; and Pb was reducible > residual > oxidizable > HOAc extractable. Cadmium was identified as being the most mobile of the elements, followed by Mn, Zn, Ni, Cu, Pb and Fe. Iron–Mn oxides can play an important role in binding Cd, Cu, Ni, Pb, and Zn and in decreasing their proportion associated with the residual fraction in the soils. With total concentrations of Cd, Cu, Ni, Pb, Zn, and Mn increase, these metals more easily release and may produce more negative effects on the urban environment.     

Geochemical patterns in soils in and around Siddipet, Medak District, Andhra Pradesh, India

This paper reports the first results of geochemical survey carried out in and around Siddipet, taking soil (topsoil 0–25 cm and subsoil 70–95 cm) as the sampling media. The data were obtained in a consistent way from 61 sites. The samples were analyzed for 29 elements (As, Ba, Cd, Co, Cr, Cu, F, Mo, Ni, Pb, Rb, Se, Sr, Th, U, V, Y, Zn, Zr, Si, Al, Fe, Mn, Mg, Ca, Na, K, Ti, and P) by X-ray fluorescence spectrometer, and baseline levels for these elements are presented. Results reveal that the correlation between the geochemical patterns in the soils developed on different litho-variants is not straight forward, but some general trends can be observed. Regional parent materials and pedogenesis are the primary factors influencing the concentrations of trace elements while anthropogenic activities have secondary influence.