CuxCe1-xO2/γ-Al2O3催化剂催化燃烧甲苯性能的研究

以γ-Al₂O₃ 为载体,以复合氧化物Cu_xCe_1-xO₂为活性组分,其中,x=0.1,0.2,0.4,0.6,0.8,通过浸渍法制备了一系列Cu_xCe_1-xO₂/γ-Al₂O₃催化剂.在固定床反应器中评价了催化剂对甲苯的催化活性,通过XRD、SEM对催化剂进行表征,并运用ICP-MS分析并计算Cu、Ce的摩尔比以及活性组分的负载量.结果表明,在Cu_xCe_1-xO₂/γ-Al₂O₃催化剂中Cu、Ce摩尔比的实际值与理论值相近,活性组分的负载量在19%以上,而且对甲苯都有较好的低温催化活性,其中当x=0.2时,即Cu_0.2Ce_0.8O₂/γ-Al₂O₃催化剂对甲苯的催化活性最高,其中T₁₀=160 ℃,T₉₀=265 ℃;当甲苯的进口浓度在700~3000 mg·m^-3时,进口浓度对Cu_0.2Ce_0.8O₂/γ-Al₂O₃催化剂的催化活性影响较小,且经过连续80 h的稳定性操作后转化率仍然保持在90%以上.     

Mn含量对Mn/ZSM-5催化剂脱硝和SO2氧化性能的影响

为研究不同Mn含量对Mn基催化剂上SO₂氧化特性的影响,采用湿式浸渍法制备了一系列不同Mn含量的Mn/ZSM-5催化剂,并研究了这些催化剂上SO₂的氧化及脱硝特性,利用一系列表征手段研究了Mn/ZSM-5催化剂的物化特性和SO₂氧化机理.结果表明：①在标准SCR（选择性催化还原）反应中,随着Mn含量和温度的升高,SO₂氧化率先增后减,并在300℃时达最大值.②在快速SCR反应中,NO₂会直接氧化SO₂,提高了SO₂的氧化率,300℃时SO₂氧化率达到最高值（0.76%）.③脱硝性能试验表明,随着温度的升高,NO_x转化率呈先升后降的特征,在快速SCR反应中NO₂促进了氧化还原反应的进行,9Mn（Mn含量为9%）催化剂在250℃时NO_x转化率达最大值（96.58%）,远高于标准SCR反应的NO_x转化率.④表征结果表明,增加Mn含量提高了晶格氧和Mn⁴⁺的含量,使SO₂氧化率和NO_x转化率均增加;但过高的Mn含量会导致催化剂表面活性物质积聚,导致晶格氧和Mn⁴⁺含量下降,从而降低锰基催化剂的氧化还原性能.研究显示,在实际运行温度范围（150~400℃）内,应选择合适的Mn含量的催化剂,保证较高的脱硝效率,降低SO₂的氧化率.     

Mn-Ce/TiO2低温SCR催化剂成型过程添加剂的影响

催化剂成型过程中添加剂的种类和添加量对成型后催化剂的机械强度、成型效果和催化性能有很大影响.本文研究了Mn-Ce/TiO₂催化剂制备过程中添加剂对催化剂的低温脱硝性能和机械性能的影响.结果表明,添加10%的拟薄水铝石作为黏结剂,可使催化剂具有较强的机械强度;添加2.5%的活性炭作为造孔剂,可以有效改善催化剂的孔结构.催化剂成型后脱硝性能下降,反应温度为90℃和120℃时,催化剂的NO_x转化率分别下降了15%和30%左右,当温度到达150℃及以上时,催化剂成型前后的脱硝性能基本一致.最后,通过BET、FT-IR、NH₃-TPD和H₂-TPR表征分析原因：成型后催化剂比表面积和孔容下降,催化剂的表面酸性位点和氧化还原能力下降都会影响催化剂的脱硝性能,所以催化剂成型后低温活性变差.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

SO2对Ag/Al2O3催化剂上CH3OH还原NO性能的影响

用溶胶-凝胶混合法制备了Ag负载量为5%的Ag/A1₂O₃催化剂.研究了富氧条件下,SO₂对CH₃OH在催化剂上还原NO性能的影响.结果表明,反应气不含SO₂和H₂O时,NO还原活性温度较低,有显著量N₂O生成,这被归因为反应过程中,部分氧化态Ag被还原为金属Ag.添加SO₂或同时添加SO₂和H_{2相似文献}   

钒和钨负载量对V2O5-WO3/TiO2表面形态及催化性能的影响

采用浸渍法制备了一系列不同钒和钨负载量的V₂O₅-WO₃/TiO₂催化剂样品,对样品NH₃选择性催化还原NO性能进行了评价,并用BET、XRD、XPS等手段对催化剂样品的表面形态进行了表征.研究发现,钒的负载量对催化剂的比表面积和催化活性有显著影响,当钒负载量从1％升高到8％时,催化剂比表面积下降了16 m²/g,最高活性温度降低了约100℃.钨起到稳定剂和助剂的双重作用,当钒负载量为1％时,钨负载量从0升高到6％,催化剂比表面积仅下降了3 m²/g,而活性温度窗口向高温和低温各拓宽了约50℃.研究表明钒和钨负载量都能影响催化剂表面的VO_x物种,但对催化剂的表面晶型没有明显影响.     

关中盆地NO2和SO2对颗粒物污染的协同效应

基于WRF-Chem模式模拟了关中盆地2019年1月2—14日一次颗粒物污染事件,评估了NO_x和SO₂减排及其在颗粒物污染中的协同作用对PM_2.5污染的影响。敏感性实验结果表明：NO_x减排可使PM_2.5中硝酸盐含量下降,但大气中O₃浓度上升,大气氧化能力增强,其他二次组分上升,导致PM_2.5下降不明显;SO₂人为源减排可使硫酸盐质量浓度下降,但由于硫酸盐在PM_2.5中占比较低,当SO₂减排75%时,PM_2.5仅下降1.74%;当减排比例较高时,NO_x和SO₂同时减排更有利于颗粒物污染防治。PM_2.5质量浓度在NO_x和SO₂同时减排75%时比分开减排75%时多下降0.75%,主要是硫酸盐下降所致;对气溶胶含水量进行分析,发现NO_x对气溶胶含水量影响较大,当NO_x减排75%时,气溶胶含水量可下降15.51%;此外,NO_x和SO₂同时减排比分开减排时气溶胶含水量更低,更不利于二次颗粒物生成。     

VOx-MnOx/TiO2催化脱除氮氧化物与二英研究

二英会降低人类的免疫力,影响人体和神经发育;氮氧化物则会对人体的各项脏器和血液组织有严重危害,还会破坏臭氧层,加速酸雨的形成.商业钒钛催化剂既能脱除氮氧化物又能催化分解二英（邻二氯苯作为模拟物）,二英活性温度区为200~300℃,而脱硝活性温度为300~400℃.研究了VO_x/TiO₂、MnO_x/TiO₂以及VO_x-MnO_x/TiO₂等催化剂在200~300℃脱硝、脱除二英的情况.结果表明,在VO_x/TiO₂催化剂中掺入MnO_x促进脱硝活性温度区间由300~400℃往200~300℃偏移,当MnO_x和VO_x摩尔比为3：1时,催化剂在250℃脱硝和脱除二英的效果最好,催化NO和邻二氯苯效率分别为92.0%和89.0%.原位红外漫反射光谱研究表明,1V3M/T催化剂表面的脱硝反应在250℃遵循L-H机理,—NH₂、N_xH_yO_z、单齿亚硝酸盐和二齿硝酸盐是主要的反应中间体.     

溴代甲烷在SO42-/TiO2上的光催化降解

采用溶胶-凝胶法制备了SO₄^2-/TiO₂催化剂,运用XRD、BET比表面测定,FTIR等技术对催化剂进行了表征,并在微型常压连续反应装置上进行CH₃Br光催化反应性能考察.结果表明,SO₄^2-引入TiO₂体系使得催化剂的结构和光催化性能得到显著改善.SO₄^2-负载量为9%,烧结温度为450℃时,SO₄^2-/TiO₂催化剂的光催化活性最高;SO₄^2-/TiO₂催化剂对反应物料中的水汽有很好的耐受性;当反应温度低于85℃时,提高反应温度,有利于改善对CH₃Br的光催化反应活性,表观活化能约为19.6kJ·mol^-1,反应温度在85℃～105℃区间时,CH3Br的光催化降解表观活化能为0.     

CeO2-La2O3/γ-Al2O3稀土氧化物混合物催化还原SO2的实验研究

在La₂O₃ 中加入变价稀土氧化物CeO₂,组成一种稀土氧化物的混合物,以这种混合物作为CO还原SO₂的催化剂.采用连续流动固定床反应器,在反应气体SO₂和CO按SO₂∶CO = 1∶3,载流气体为N₂,气体流量为1000 mL/min的条件下,实验研究了该催化剂的活化过程以及温度和反应物浓度配比对活化反应的影响,用XRD和XPS对反应前后催化剂进行了表征,分析了相结构的变化.结果表明:CeO₂和La₂O₃ 2种稀土氧化物的混合物,在CO还原SO₂的催化反应中,活化温度比单个的CeO₂或La₂O₃氧化物下降了50℃～100℃,而且具有更高的活性.这可能是CeO₂和La₂O₃氧化物之间存在着某种协同作用所致.     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

Improvement of the activity and SO2 tolerance of Sb-modified Mn/PG catalysts for NH3-SCR at a low temperature

A series of MnM/palygorskite (PG) (M = La, W, Mo, Sb, Mg) catalysts was prepared by the wetness co-impregnation method for low-temperature selective catalytic reduction (SCR) of NO with NH₃. Conversion efficiency followed the order Sb > Mo > La > W > Mg. A combination of various physico-chemical techniques was used to investigate the influence of Sb-modified Mn/PG catalysts. MnSb_0.156/PG catalyst showed highest NO conversion at low temperatures in the presence of SO₂ which reveals that addition of Sb oxides effectively enhances the SCR activity of catalysts. A SO₂ step-wise study showed that MnSb_0.156/PG catalyst displays higher durable resistance to SO₂ than Mn/PG catalyst, where the sulfating of active phase is greatly inhibited after Sb doping. Scanning electron microscopy and X-ray diffraction results showed that Sb loading enhances the dispersion of Mn oxides on the carrier surface. According to the results of characterization analyses, it is suggested that the main reason for the deactivation of Mn/PG is the formation of manganese sulfates which cause the permanent deactivation of Mn-based catalysts. For Sb-doped Mn/PG catalyst, SO_x ad-species formed were mainly combined with SbO_x rather than MnO_x. This preferential interaction between SbO_x and SO₂ effectively shields the MnO_x as active species from being sulfated by SO₂ resulting in the improvement of SO₂ tolerance on Sb-added catalyst. Multiple information support that, owing to the addition of Sb, original formed MnO_x crystallite has been completely transformed into highly dispersed amorphous phase accounting for higher SCR activity.     

Effect of MoO3 on vanadium based catalysts for the selective catalytic reduction of NOx with NH3 at low temperature

The selective catalytic reduction(SCR) activities of the MoO_3 doped V/WTi catalysts prepared by the incipient wetness impregnation method at low temperature were investigated.The results showed that the addition of MoO_3 could enhance the NO_ xconversion at low temperature and the best SCR activity was obtained when the dosage of MoO_3 reached5 wt.%. The NH3-TPD and DRIFTS experiments indicated that the addition of MoO_3 changed the type and number of acid sites on the surface of catalysts and reaction activities of acid sites were altered at the same time. The redox capacity and amount of active oxygen species got improved for V3Mo5/WTi catalyst, which could be confirmed by the H_2-TPR and transient response experiments. Water vapor inhibited the NO_xconversion at low temperature. Deposition of ammonium sulfate or bisulfate might be main reason for the loss of catalytic activity in the presence of SO_2 at low temperature. Choosing the suitable NH_3/NO ratio and elevation of reaction temperature both could weaken the influence of SO_2 on the SCR activity of the V3Mo5/WTi catalyst. Thermal treatment of the deactivated catalyst at350°C could get the low temperature activity recovered. The decrease of GHSV improved the de NO_x efficiency at low temperature and we speculated that the rational technological process and operation parameters could contribute to the application of this kind of catalysts in real industrial environment.     

V2O5/TiO2催化剂中毒机理的试验研究

选择性催化还原(SCR)催化剂是SCR烟气脱硝技术的核心,是整个SCR系统脱硝效率和经济性的决定因素.本文工作的主要研究思路是以钒钛SCR催化剂为研究对象,研究了H2O和SO2,以及相同含量下K、Na、Ca、Pb的氧化物对钒钛催化剂NO转化率的影响.H2O的存在会抑制V2O5/TiO2催化剂脱硝活性,而SO2在一定程度上促进(V2O5/TiO2)催化剂的SCR脱硝反应,提高NO转化率;碱金属K对钒钛催化剂的钝化作用都是最强,K2O和Na2O的掺入会抑制钒钛催化剂上V2O5的还原能力,而CaO和PbO的掺入对钒钛催化剂上V2O5的还原能力影响较小.     

Mn/TiO2和Mn-Ce/TiO2低温脱硝催化剂的抗硫性研究

在低温选择性催化还原(SCR)反应条件下考察了烟气残余SO2对Mn/TiO2和Mn-Ce/TiO2催化剂选择性催化还原活性的影响,同时对SO2的影响机理进行了探讨.结果发现,Mn/TiO2催化剂在SO2反应气氛中失活很快,硫铵盐的沉积和活性组分的硫酸化是催化剂失活的重要原因;Ce的加入可以有效地抑制催化剂活性组分的硫酸化,同时还能降低硫酸盐在催化剂表面的稳定性,从而可以提高催化剂的抗硫性.     

Numerical evaluation of the effectiveness of NO2 and N2O5 generation during the NO ozonation process

Wet scrubbing combined with ozone oxidation has become a promising technology for simultaneous removal of SO₂ and NO_x in exhaust gas. In this paper, a new 20-species, 76-step detailed kinetic mechanism was proposed between O₃ and NO_x. The concentration of N₂O₅ was measured using an in-situ IR spectrometer. The numerical evaluation results kept good pace with both the public experiment results and our experiment results. Key reaction parameters for the generation of NO₂ and N₂O₅ during the NO ozonation process were investigated by a numerical simulation method. The effect of temperature on producing NO₂ was found to be negligible. To produce NO₂, the optimal residence time was 1.25 sec and the molar ratio of O₃/NO about 1. For the generation of N₂O₅, the residence time should be about 8 sec while the temperature of the exhaust gas should be strictly controlled and the molar ratio of O₃/NO about 1.75. This study provided detailed investigations on the reaction parameters of ozonation of NO_x by a numerical simulation method, and the results obtained should be helpful for the design and optimization of ozone oxidation combined with the wet flue gas desulfurization methods (WFGD) method for the removal of NO_x.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

次氯酸钠湿法烟气脱硝及同时脱硫脱硝技术研究

采用NaClO作氧化吸收剂,在鼓泡反应装置进行了湿法烟气脱硝实验研究,考察了NaIO、NO浓度、液相温度、气体流量、pH对脱硝效率的影响以及SO2对同时脱硫脱硝效率的影响,并结合液相产物分析探讨了同时脱硫脱硝反应机理.研究结果表明,pH值是影响活性成分HClO存在形式的重要因素,同时也是影响氧化吸收的关键因素;在一定范...     

Effects of WOx modification on the activity, adsorption and redox properties of CeO2 catalyst for NOx reduction with ammonia

A series of WO₃/CeO₂ (WOx/CeO₂) catalysts were synthesized by wet impregnation of ammonium metatungstate on a CeO₂ support. The resulting solid acid catalysts were characterized by X-ray diffraction (XRD), UV-Vis spectroscopy (UV-Vis), Raman spectroscopy (Raman), in-situ Fourier transform infrared spectroscopy (in-situ FT-IR) of ammonia adsorption, NH₃-TPD, H₂ temperature-programmed reduction (H₂-TPR), NH₃/NO oxidation and activity measurements for NOx reduction by NH₃ (NH₃-SCR). The results show that polytungstate (WOx) species are the main species of tungsten oxide on the surface of ceria. The addition of tungsten oxide enhances the Brönsted acidity of ceria catalysts remarkably and decreases the amount of surface oxygen on ceria, with strong interaction between CeO₂ and WOx. As a result, the N₂ selectivity of NH₃ oxidation and NH₃-SCR at high temperatures (> 300℃) is enhanced. Therefore, a wide working temperature window in which NOx conversion exceeds 80% (NOx conversion > 80%) from 200 to 450℃, is achieved over 10 wt.% WOx/CeO₂ catalyst. A tentative model of the NH₃-SCR reaction route on WOx/CeO₂ catalysts is presented.     

液相氧化-吸收脱除模拟烟气中NOx的研究

分别采用Na Cl O2和Na2SO3溶液作为氧化液和吸收液,在自行设计的鼓泡塔反应系统进行了液相氧化-吸收脱除模拟烟气NOx的研究,考察了气相SO2浓度、Na Cl O2和Na2SO3投加量以及p H值等因素对NO氧化和NOx脱除的影响.结果表明,SO2会优先于NO与氧化剂反应,从而增大氧化剂消耗量.偏酸性条件有利于NO氧化,但酸性太强会导致Na Cl O2分解为Cl O2逸出.碱性吸收液对NO几乎不具吸收脱除效果,但共存NO2能促进NO的吸收脱除.SO2对NO2吸收脱除具有促进作用.