Oil Spill Modeling towards the Close of the 20th Century: Overview of the State of the Art

The state-of-the-art in oil spill modeling is summarized, focusing primarily on the years from 1990 to the present. All models seek to describe the key physical and chemical processes that transport and weather the oil on and in the sea. Current insights into the mechanisms of these processes and the availability of algorithms for describing and predicting process rates are discussed. Advances are noted in the areas of advection, spreading, evaporation, dispersion, emulsification, and interactions with ice and shorelines. Knowledge of the relationship between oil properties, and oil weathering and fate, and the development of models for the evaluation of oil spill response strategies are summarized. Specific models are used as examples where appropriate. Future directions in these and other areas are indicated     

Pyrolysis of tyres. Influence of the final temperature of the process on emissions and the calorific value of the products recovered

A study was made of the pyrolysis of tyre particles, with the aim of determining the possibilities of using the products resulting from the process as fuel. Three final temperatures were used, determined from thermogravimetric data. The design of the experiment was a horizontal oven containing a reactor into which particles of the original tyre were placed. After the process, a solid fraction (char) remained in the reactor, while the gases generated went through a set of scrubbers where most of the condensable fraction (oils) was retained. Finally, once free of this fraction, the gases were collected in glass ampoules. Solid and liquids fractions were subjected to thermogravimetric analyses in order to study their combustibility. The gas fraction was analysed by means of gas chromatography to establish the content of CO, CO2, H2 and hydrocarbons present in the samples (mainly components of gases produced in the pyrolysis process). A special study was made of the sulphur and chlorine content of all the fractions, as the presence of these elements could be problematic if the products are used as fuel. Tyre pyrolysis engenders a solid carbon residue that concentrates sulphur and chorine, with a relatively high calorific value, although not so high as that of the original tyre. The liquid fraction produced by the process has a high calorific value, which rises with the final temperature, up to 40 MJ/kg. The chlorine content of this fraction is negligible. Over 95% of the gas fraction, regardless of the final temperature, is composed of hydrocarbons of a low molecular weight and hydrogen, this fraction also appearing to be free of chlorine.     

Economic aspects of the rehabilitation of the Hiriya landfill

The Hiriya landfill, Israel's largest, operated from 1952 to 1998. The landfill, located in the heart of the Dan Region, developed over the years into a major landscape nuisance and environmental hazard. In 1998, the Israeli government decided to close the landfill, and in 2001 rehabilitation activities began at the site, including site investigations, engineering and scientific evaluations, and end-use planning. The purpose of the present research is to perform a cost-benefit analysis of engineering and architectural-landscape rehabilitation projects considered for the site. An engineering rehabilitation project is required for the reduction of environmental impacts such as greenhouse gas emissions, slope instability and leachate formation. An architectural-landscape rehabilitation project would consider improvements to the site to make it suitable for future end uses such as a public park. The findings reveal that reclamation is worthwhile only in the case of architectural-landscape rehabilitation of the landfill, converting it into a public park. Engineering rehabilitation alone was found to be unjustified, but is essential to enable the development of a public park.     

Monitoring of the Degradation Activities and the Diversity of the Microbial Community Degrading Refinery Waste Sludge

The biodegradation of n-alkanes and branched alkanes from waste sludge were observed in landfarming soils of Motor Oil Hellas (a petroleum refinery) and changes in the bacterial communities in the soils were monitored during the remediation. Bacterial 16S rRNA gene (rDNA)-based community fingerprint patterns were obtained from soil samples by terminal restriction fragment length polymorphism (T-RFLP) analysis. Changes in T-RFLP fingerprints, as well as in the petroleum contaminant composition of the polluted soil, correlated with degradation activities in field tests.     

On the Methods for the Delimitation of Seasons

It is well known that air pollution is one of the major factors affecting human health and the activities in a town. Among the various air pollutants an interesting one, especially for sunny climates, is the reactive O₃. O₃ varies significantly through the year; it is therefore very important to know the onset and the duration of the warm period of the year since at that time O₃ concentrations increase significantly. In this work, an attempt was made to determine the onset of warm season of the year as well as its duration in various sites located in Northeastern Mediterranean. For this purpose, a fuzzy clustering method is used. The method was applied on the isobaric thickness between 1000 and 500 hPa for the period from 1974 to 1997. The results were compared to conventional methods based on synoptic classification and were found to be in good agreement.     

区域特性分析在广东烟气脱硫工艺优选中的应用

电厂优选烟气脱硫工艺时必须进行切合实际的区域特性分析。石灰石—石膏湿法烟气脱硫工艺成熟、稳定、高效，且具有适应广东区域特点的诸多优势，故存在着广阔的发展前景。     

A comparison of the comprehensive municipal solid waste management systems of the region of Prague and the principality of Asturias. the influence of collection systems and municipality size on the waste collection and the recycling rates

Journal of Material Cycles and Waste Management - The correct management of municipal solid waste (MSW) is a critical factor in the protection of the environment, as well as a source for the...     

Fundamental study of the behavior of chlorine during the combustion of single RDF

A fundamental study of the combustion characteristics and the de-HCl behavior of a single refuse-derived fuel (RDF) pellet was carried out to explain the de-HCl phenomena of RDF during fluidized bed combustion and to provide data for the development of high efficiency power generation technology using RDF. In this research, combustion and pyrolysis experiments were carried out in an electrical furnace using a series of model and actual RDF samples. The de-HCl capability of Ca(OH)2 in RDF was evaluated by measuring the emission fraction of HCl in the flue gas and the capture fraction of Cl in the residue. It was found that the capture fraction of Cl components in the residue increased from 0 to nearly 70% when the molar ratio of Ca/Cl was changed from 0 to around 13. Apparently, the capture fraction also decreased with increasing oxygen concentration in the feed gas. The devolatilization process of RDF was confirmed to be a very important part of de-HCl process. The effect of temperature profile of the RDF pellet on the de-HCl process, as it varies with the heating rate of RDF and the oxygen concentration in the vicinity of the sample, is discussed.     

Revisiting the elemental composition and the calorific value of the organic fraction of municipal solid wastes

In this work, the elemental content (C, N, H, S, O), the organic matter content and the calorific value of various organic components that are commonly found in the municipal solid waste stream were measured. The objective of this work was to develop an empirical equation to describe the calorific value of the organic fraction of municipal solid waste as a function of its elemental composition. The MSW components were grouped into paper wastes, food wastes, yard wastes and plastics. Sample sizes ranged from 0.2 to 0.5 kg. In addition to the above individual components, commingled municipal solid wastes were sampled from a bio-drying facility located in Crete (sample sizes ranged from 8 to 15 kg) and were analyzed for the same parameters. Based on the results of this work, an improved empirical model was developed that revealed that carbon, hydrogen and oxygen were the only statistically significant predictors of calorific value. Total organic carbon was statistically similar to total carbon for most materials in this work. The carbon to organic matter ratio of 26 municipal solid waste substrates and of 18 organic composts varied from 0.40 to 0.99. An approximate chemical empirical formula calculated for the organic fraction of commingled municipal solid wastes was C₃₂NH₅₅O₁₆.     

Effect of the Incorporation of Lysozyme on the Properties of Jackfruit Starch Films

Jackfruit starch based biodegradable films containing lysozyme were characterized for their antimicrobial activity, thickness, solubility, water vapor permeability and mechanical properties. The biodegradable films had good appearance and antimicrobial activity against Micrococcus lysodeikticus. The thickness of the biodegradable films were not affected by the variation in pH, but the addition of lysozyme increased the thickness, the thickest films being those with the highest lysozyme concentrations. The variation in pH of the filmogenic solutions affected the solubility of the biodegradable films, water solubility being greatest at pH 7.0 and with the highest lysozyme concentration. The permeability of the biodegradable films was increased by incorporating lysozyme. The lysozyme concentration and pH variation caused changes in the mechanical properties. The addition of 8% lysozyme increased the tensile strength and Young’s modulus for all the pH values studied. With respect to the release of antimicrobial activity, the diffusion of lysozyme was shown to follow Fickian transport mechanism.     

Proposal for the integration of decentralised composting of the organic fraction of municipal solid waste into the waste management system of Cuba

Municipal solid waste (MSW) generation and management in Cuba was studied with a view to integrating composting of the organic fractions of MSW into the system. Composting is already included as part of the environmental strategy of the country as an appropriate waste management solution. However, no programme for area-wide implementation yet exists. The evaluation of studies carried out by some Cuban and international organisations showed that organic matter comprises approximately 60-70% of the MSW, with households being the main source. If all organic waste fractions were considered, the theoretical amount of organic waste produced would be approximately 1 Mio. Mg/a, leading to the production of approximately 0.5 Mio. Mg/a of compost. Composting could, therefore, be a suitable solution for treating the organic waste fractions of the MSW. Composting would best be carried out in decentralised systems, since transportation is a problem in Cuba. Furthermore, low technology and low budget composting options should be considered due to the problematic local economic situation. The location for such decentralised composting units would optimally be located at urban agricultural farms, which can be found all over Cuba. These farms are a unique model for sustainable farming in the world, and have a high demand for organic fertiliser. In this paper, options for the collection and impurity-separation in urban areas are discussed, and a stepwise introduction of source-separation, starting with hotel and restaurant waste, is suggested. For rural areas, the implementation of home composting is recommended.     

A Review of the Fate and Effects of Silicones in the Environment

Silicones are well-known useful materials varying in structure, reactivity, and chemical and physical properties, but they all contain a covalent bond between the silicon atom and an organic group. Most common of these polymers are those based on polydimethylsiloxane (PDMS) having a siloxane (Si–O–Si) repeat unit and two methyl groups on each silicon atom. All these polymers are manmade, and the organosilicon linkage is not found in nature. It was therefore erroneously assumed that these polymers do not degrade naturally in the environment. It is the purpose of this review to refute this myth and to describe the degradation processes of PDMS in the environment and any potential ecological impact on the terrestrial, aquatic, and atmospheric compartments. Although it was found that minor degradation takes place by hydrolysis of PDMS to dimethylsilandiol followed by oxidation of the methyl group to aldehyde and ultimately to CO₂ by Arthobacter and Fusarium oxysporium schlechtendahl, the major degradation processes are abiotic. High molecular weight PDMS are initially depolymerized by soil hydrolysis of the siloxane bonds to yield organosilanol terminated oligomers. These organosilanols and low molecular weight linear PDMS and cyclics are evaporated into the atmosphere and are oxidized there by hydroxyl radicals to benign silica, water, and CO₂.     

Study of the evaporation process of saline waste from the tanning industry.

The second and third steps of wastewater treatment in the tanning industry generate sludges that are rich in salts, organic matter and suspended solids. Since these are formally catalogued as industrial wastes by environmental legislation, they cannot be disposed of directly but need a final treatment. One of the problems with these wastes is their high water content, which has to be reduced. In the particular case of the concentrated streams from the secondary and tertiary treatment steps, the sludges are first concentrated by evaporation, and the evaporated water is used in other parts of the plant. This study, which preceded evaporator design, analysed the evaporation process (laboratory scale) of a saline residue produced in the reverse osmosis step of the treatment of tanning wastewaters by the company Aquagest Levante, S.A. in Lorca (Murcia, Spain), to ascertain its behaviour in the evaporation process and the evolution of its physical properties. The study served to determine the exact mineralogy and ionic composition as well as the characteristics of the waste in question. This information was used in the last step of the design of the evaporation equipment.     

Lead Speciation in the Sediments of the Heavily Polluted Western Harbor of Alexandria

The Western Harbor (WH) became under stress in the past decades, following successive increase in population. This study deals with local distribution of total lead and its species in the WH sediments. The lead content was high and there was a relationship between its enrichment and oil dispersed from ships. The lowest total lead value was found in the harbor middle far from direct effects of pollution. A five-step sequential extraction scheme was applied to illustrate the contribution shared by each individual fraction in the total lead concentration in the WH sediments. The exchangeable fraction (F1) was very low. The bound to carbonate fraction (F2), the bound to iron-manganese oxide fraction (F3) and the bound to organic matter—sulfide fraction (F4) ranked fourth, second and third in abundance. Oxygen was the main factor controlling the value of F2. F3 gave a direct relationship with total lead. The high levels of F4 occurred at locations of low salinity and enriched with organic matter. The residual fraction (F5) dominated other lead species, reflecting the sediment composition and the amounts of discharged pollutants.     

An event study on the concealment of the blending ratio of waste paper

We conducted an event study on the concealment of the blending ratio of waste paper with virgin pulp in Japan. By investigating 10 companies in the paper industry between May 30, 2007 and January 18, 2008, we clearly show that stock prices of the relevant companies were affected by the news on the concealment of the blending ratio of waste paper. In addition, the impact of the second event was found to be greater than that of the first event. Therefore, the concealment of major companies negatively affects the stock prices of non-major companies, which did not conceal information during this period. Thus, bad news is negatively assessed by the market, and this influence has spread in the paper industry in general.     

Assessment of Several Test Methods for the Determination of the Anaerobic Biodegradability of Polymers

Anaerobic degradation of eight commercially available biodegradable polymers was compared in two anaerobic tests using digestion sludge, according to ISO 11734 and ASTM D.5210-91. Cotton, polyhydroxybutyrate/hydroxyvalerate copolymer (PHB/PHV), starch blend, thermoplastic cellulose acetate, and cellulose acetate fibers proved to be anaerobically degradable, but only a low extent of degradation was found for polylactide, polyvinylalcohol, and polycaprolactone. Both test methods gave the same overall results, but with the ISO medium, longer lag phases and greater ranges of variation in the results were observed. These effects are presumably due to low concentrations of carbon dioxide in the ISO medium. Carbon dioxide has been demonstrated to be essential for the growth of various anaerobic bacteria, notably homoacetogenic and methanogenic bacteria.     

Adapting the Speciation of the VOCs Emission Inventory in the Greater Athens Area

An adaptation procedure of a new emission inventory of theGreater Athens Area is attempted, based on a sensitivityanalysis on the treatment of the VOC emissions. Throughthis procedure the impact that a more detailed treatment ofthe VOCs emissions might have on the atmospheric chemistrysimulations, is examined. For this analysis three differentchemical mechanisms were applied for two differentlocations (urban and city plume) with different VOC andNO_x mixture characteristics. Finally, this studyrecommends new carbon fractions, reflecting the localconditions in Athens basin.     

Comparative Thermodynamic Study on the Contribution of the Autocondensation and Copolymerization Reactions for the Tannins of the Subspecies of Acacia nilotica

Autocondensation and copolymerization reactions of the Acacia nilotica subspecies tomentosa (Ant) and the subspecies adansonii (Ana) tannins extracts solutions have been studied at several pH values by thermomechanical analyzer. Results of chemical analysis of these tannins revealed that the studied tannins, Ant and Ana contained high percentages of extractable tannins (54 and 57 %) for and polyphenolic materials (78 and 80 %) respectively. Different hardeners such as paraformaldehyde, Urea and pMDI were added at different ratios and their polycondensation reactions was studied and compared with their autocondensation ones. The aim was to evaluate the tannins suitability for the production of commercially and technically viable tannin adhesives with reduced Formaldehyde emission for wood products and to study the interference between the autocondensation and the copolymerization reaction. The obtained results of autocondensation reaction for both of the tannins studied showed that the best Young’s modulus values for Ant (3,500 and 2,750 MPa) and Ana (2,650 and 2,620 MPa) were obtained at pH 5 and 7. The Young’s modulus values obtained by the tannins Ant were higher than those achieved by Ana. This indicates that the Ant is more reactive than Ana. These results were also in line with results achieved by the gel time for both of the tannins. Gel time results indicate that the reactivity of both tannins increased towards alkalinity with Ana being more reactive at alkaline pH. Addition of 8 % of paraformaldehyde was adversely affecting the autocondensation reactions, as the best Young’s modulus values were achieved at pH 4 for Ant tannins. As for Ana the higher Young’s modulus values (2,000 and 2,310 MPa) were achieved at pH 5 and 7. This indicates that autocondensation reaction was contributed to the final network of the copolymerization reaction. When smaller ratio of paraformaldehyde and Urea (5 %) was added to Ant tannins it favors the autocondensation reaction and the best Young’s modulus values were obtained at pH 5 and 7. Addition of pMDI (10–30 %) was found to decrease the temperature of copolymerization and the obtained Young’s modulus values by Ant were lower than those obtained by autocodensation reaction. Best Young’ modulus values were obtained by Ant at pH 5 and 7. Ana gave the best Young’s modulus values at pH 4 and 5 indicating that the autocondensation appears to depress the copolymerization reactions. The obtained results by both reactions were very important from technical and economical point of view as they concluded that it is very possible to produce adhesives system with zero emission depending on the tannins autocondensation reaction and pH values. Reduction of formaldehyde emission was also possible upon addition of smaller amount of paraformaldehyde and Urea.     

Contamination of the environment by the current disposal methods of mercury-containing lamps in the state of Minas Gerais, Brazil.

This survey describes the degree of environmental contamination resulting from the current disposal methods of mercury-containing lamps. The territory studied for this purpose is the federal state of Minas Gerais, one of the most populated areas in the Brazilian federation of states. The results of this survey derive in part from answers received to a questionnaire mailed out to industrial firms, commercial business enterprises, hospitals and departments of public work. The sampling technique used was a nonprobabilistic (purposive sampling). Three types of disposal were found to prevail: (1) as an addition to corporate waste disposal (garbage), (2) recycling and (3) disposal by other methods. Overall, our study shows that the majority of mercury lamps are being disposed in the metropolitan area of Belo Horizonte, primarily by the public sector, followed by industrial, commercial and hospital sectors. Although recycling constitutes a relatively high fraction of the disposal methods, we find Federal regulations in Brazil regarding the disposal of hazardous, mercury-containing lamps to be far behind the state of technological achievement. This gap has permitted the adoption of disposal measures that are obsolete, incorrect, and a primary cause for the extensive contamination of the ecosystems with harmful effects to human health.     

Assessment of the leaching of metallic elements in the technology of solidification in aqueous solution

Results are presented of experiments performed to optimize the solidification/stabilization system for metallic elements in aqueous solution. This system involves mixing cement and a solution of metallic elements in a conventional mixer: the paste thus obtained is transferred drop by drop into a recipient filled with an aqueous solution of NaOH at 20% by weight, in which it solidifies immediately. The separate use of chloride solutions of Li+, Cr3+, Pb2+ and Zn2+ makes it possible to obtain granules displaying various levels of compressive strength. Three different inertization matrices were used in the experiments, the first consisting solely of Portland cement, the second of Portland cement and a superplasticizer additive, and the third of Portland cement partially replaced with silica-fume and superplasticizer. The results of the tests performed showed a very low level of leaching into the alkaline solidification solution for Cr3+, the quantity leached being under 2% as against higher levels for the other metallic elements. For all the considered elements, the best results were obtained by using silica-fume in the inertization matrix.