Reduction of tar using cheap catalysts during sewage sludge gasification

Solid-fuel conversion or gasification study of sewage sludge and energy recovery has become increasingly important because energy recovery and climate change are emerging issues. Various types of catalysts, such as dolomite, steel slag and calcium oxide, were tested for tar reduction during the sewage sludge gasification process. For the experiments on sewage sludge gasification reactions and tar reduction using the catalysts, a fixed bed of laboratory-scale experimental apparatus was set up. The reactor was made of quartz glass using an electric muffle furnace. The sewage sludge samples used had moisture contents less than 6%. The experimental conditions were as follows: sample weight was 20 g and reaction time was 10 min, gasification reaction temperature was from 600 to 800°C, and the equivalence ratio was 0.2. The quantity of catalysts was 2–6 g, and temperatures of catalyst layers were 500–700°C. As the reaction temperature increased up to 800°C, the yields of gaseous products and liquid products increased, whereas char and tar products decreased, showing effects on gas product compositions. These results were considered to be due to the increase of the water-gas reaction and Boudouard reaction. In the case of experiments with catalysts, dolomite (4 g), steel slag (6 g) and calcium oxide (6 g) were used. When the temperature of catalysts increased, the weight of the tar produced decreased with different cracking performances by different catalysts. Reforming reactions were considered to occur on the surface of dolomite, steel slag and calcium oxide, causing cracking of the hydrocarbon structure, which eventually showed reduced tar generation.     

废催化裂化催化剂的危险性及污染特征

为考察我国废催化裂化(FCC)催化剂的危险性及污染特征,以国内典型FCC装置的废催化剂为研究对象,分析其易燃性、反应性、腐蚀性、浸出毒性、毒性物质含量及急性毒性。研究发现:废FCC催化剂无易燃性、反应性、腐蚀性、急性毒性危险;未检测出具有致癌致突变性的有机污染物;废FCC催化剂的特征污染物为Ni及其化合物,Ni的浸出浓度低于国家标准限值,Ni的存在形态为Ni Al2O4尖晶石,而非具有致癌性的Ni O形态。     

钙钛矿型催化剂催化湿式氧化处理煤气化废水纳滤浓缩液

采用溶胶-凝胶法制备了Mn掺杂钙钛矿型催化剂LaFexMn1-xO3,并以其为催化剂催化湿式双氧水氧化处理煤气化废水纳滤浓缩液。采用XRD,SEM,FTIR技术对催化剂进行了表征。表征结果显示：制备的催化剂均具有标准的钙钛矿型结构,其中,LaFe0.9Mn0.1O3的结构稳定,比表面积大。实验结果表明：制备的催化剂中LaFe0.9Mn0.1O3的催化活性最高,且稳定性好,连续使用5次后催化活性未见明显减弱;在H2O2投加量3.0 g/L、n（H2O2）∶n（LaFe0.9Mn0.1O3）=12∶1、反应温度160 ℃、反应压力1 MPa、浓缩液pH 3、反应时间60 min的最优条件下,COD、UV254和TOC的去除率分别达到80.9%、95.2%和68.0%,BOD5/COD由0.02提升至0.40,可生化性大幅提高。     

Production of gaseous fuel from refuse plastic fuel via co-pyrolysis using low-quality coal and catalytic steam gasification

In this study, refuse plastic fuel (RPF) was copyrolyzed with low-quality coal and was gasified in the presence of a metal catalyst and steam. Some metal catalysts, such as Ni, NiO, and Mg, and mixtures of these with base promoters such as Al₂O₃ and Fe₂O₃ were employed in the pyrolysis and gasification processes to convert the synthesis gas into more valuable fuel gas. The operating temperatures for the pyrolysis and gasification were between 700° and 1000°C. The experimental parameters were the operating temperature, catalyst type, basic promoter type, and steam injection amount. Solid fuel samples (5 g) were fed into a semibatch-type quartz tube reactor when the reactor reached the designated temperature. The synthesis gas was analyzed by gas chromatography. The use of low-quality coal as fuel in co-pyrolysis with RPF was explored. For the co-pyrolysis of RPF and low-quality coal, the effectiveness of the catalysts for fuel gas production followed the order Mg > NiO > Ni. In catalytic gasification of RPF, the addition of Al₂O₃ seemed to reduce the activity of the corresponding catalysts Ni and Mg. The maximum fuel gas yield (92.6%) was attained when Mg/Fe₂O₃ was used in steam gasification at 1000°C.     

Geopolymer synthesized from spent fluid catalytic cracking catalyst and its heavy metal immobilization behavior

Journal of Material Cycles and Waste Management - Porous geopolymers (GP) are energy saving, environment-friendly and simple in preparation, which has attracted increasing attention from both...     

Improved biogas production from rice straw by co-digestion with kitchen waste and pig manure

In order to investigate the effect of feedstock ratios in biogas production, anaerobic co-digestions of rice straw with kitchen waste and pig manure were carried out. A series of single-stage batch mesophilic (37 ± 1 °C) anaerobic digestions were performed at a substrate concentration of 54 g/L based on volatile solids (VS). The results showed that the optimal ratio of kitchen waste, pig manure, and rice straw was 0.4:1.6:1, for which the C/N ratio was 21.7. The methane content was 45.9–70.0% and rate of VS reduction was 55.8%. The biogas yield of 674.4 L/kg VS was higher than that of the digestion of rice straw or pig manure alone by 71.67% and 10.41%, respectively. Inhibition of biogas production by volatile fatty acids (VFA) occurred when the addition of kitchen waste was greater than 26%. The VFA analysis showed that, in the reactors that successfully produced biogas, the dominant intermediate metabolites were propionate and acetate, while they were lactic acid, acetate, and propionate in the others.     

Effect of water washing on the thermal behavior of rice straw

Rice straw can be used as a renewable fuel for heat and power generation. It is a viable mean of replacing fossil fuels and preventing pollution caused by open burning, especially in the areas where this residual biomass is generated. Nevertheless, the thermal conversion of rice straw can cause some operating problems such as slag formation, which negatively affects thermal conversion systems. So, the main objective of this research is studying the combustion behavior of rice straw samples collected from various regions by applying thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). In addition, the thermal behavior of ashes from rice straw was also analyzed in order to detect their melting points, and ash sintering was detected at different temperatures within the range between 550 and 1000 °C. Since washing rice straw with water could reduce the content of undesirable inorganic compounds related to the ash fusibility, samples of washed rice straw were analyzed under combustion conditions to investigate its differences regarding the thermal behavior of rice straw. The results showed that rice straw washing led to a significant improvement in its thermal behavior, since it reduced the ash contents and sintering formation.     

Transportation fuel production by combination of LDPE thermal cracking and catalytic hydroreforming

Fuel production from plastics is a promising way to reduce landfilling rates while obtaining valuable products. The usage of Ni-supported hierarchical Beta zeolite (h-Beta) for the hydroreforming of the oils coming from LDPE thermal cracking has proved to produce high selectivities to gasoline and diesel fuels (>80%). In the present work, the effect of the Ni loading on Ni/h-Beta is investigated in the hydroreforming of the oils form LDPE thermal cracking. h-Beta samples were impregnated with Ni nitrate, calcined and reduced in H₂ up to 550 °C to achieve different Ni contents: 1.5%, 4%, 7% and 10%. Larger and more easily reducible metal particles were obtained on Ni 7%/h-Beta and Ni 10%/h-Beta. Hydroreforming tests were carried out in autoclave reactor at 310 °C, under 20 bar H₂, for 45 min. Ni content progressively increased the amount of gases at the expenses of diesel fractions, while gasoline remained approximately constant about 52–54%. Maximum selectivity to automotive fuels (～81%) was obtained with Ni 7%/h-Beta. Ni loading also enhanced olefins saturation up to Ni 7%/h-Beta. High cetane indices (71–86) and octane numbers (89–91) were obtained over all the catalysts. Regarding the different studied Ni contents, Ni 7%/h-Beta constitutes a rather promising catalyst for obtaining high quality fuels from LDPE thermal cracking oils.     

Multiple use of waste catalysts with and without regeneration for waste polymer cracking

Waste plastics contain a substantial number of valuable chemicals. The wastes from post-consumer as well as from industrial production can be recycled to valuable chemical feedstock, which can be used in refineries and/or petrochemical industries. This chemical recycling process is an ideal approach in recycling the waste for a better environment. Polymer cracking using a laboratory fluidised bed reactor concentrated on the used highly contaminated catalyst, E-Cat 2. Even though E-Cat 2 had low activity due to fewer acid sites, the products yielded were similar with amorphous ASA and were far better than thermal cracking. The high levels of heavy metals, namely nickel and vanadium, deposited during their lifetime as an FCC catalyst, did not greatly affect on the catalyst activity. It was also shown that E-Cat 2 could be used with and without regeneration. Although there was more deactivation when there was no regeneration step, the yield of gases (C₂-C₇) remained fairly constant. For the first time, these results indicate that “waste” FCC catalyst (E-Cat) is a good candidate for future feedstock recycling of polymer waste. The major benefits of using E-Cat are a low market price, the ability to tolerate reuse and regeneration capacity.     

Preparation of hydrogen-rich gas from waste polyurethane foam by steam gasification and catalytic reforming in a two-stage fixed bed reactor

Journal of Material Cycles and Waste Management - The reclamation of waste rigid polyurethane foam (WRPUF) is capable of realizing both circulations of waste and protection of the environment. In...     

CeMn氧化物催化剂的制备及其对甲苯的催化降解性能

采用草酸沉淀法合成了铈锰氧化物(CeMn氧化物)催化剂,在固定床反应器中考察了不同Ce-Mn摩尔比、空速对CeMn氧化物催化剂催化降解甲苯效果的影响,通过XRD、SEM、XPS等技术表征了催化剂的理化性质.实验结果表明:当n(Ce):n(Mn)=1:3时得到的Ce1Mn3催化剂降解甲苯的活性最佳,T50=198℃,T9...     

Pyrolysis of low-density polyethylene using synthetic catalysts produced from fly ash

Catalytic pyrolysis of low-density polyethylene (LDPE) was investigated using various fly ash-derived silica–alumina catalysts (FSAs). FSAs were prepared by a simple activation method that basically includes NaOH treatment of fly ash by a fusion method, followed by an aging process. A series of LDPE pyrolysis experiments was conducted and the catalytic performance of FSAs was assessed in terms of the degradation temperature and the simulated boiling point distribution of the liquid products. The effects of synthesis conditions such as NaOH/fly ash weight ratio and aging time were examined by X-ray diffractometer (XRD), Brunauer-Emmett-Teller (BET) surface area analyzer, and scanning electron microscope to clarify the controlling factors affecting the catalytic activity. To obtain catalyst with high activity, it is necessary to produce sufficient silica and alumina species that can be easily co-precipitated into solid acid catalyst by destruction of the fly ash structure and to optimize the activation time for catalyst synthesis to prevent the transformation into inactive phases. The catalytic performance of FSA obtained from optimal conditions was equivalent to that of commercial catalysts, demonstrating the effectiveness of the catalyst.     

Influence of moisture content,particle size and forming temperature on productivity and quality of rice straw pellets

A large amount of rice straw is generated and left as much in paddy fields, which causes greenhouse gas emissions as methane. Rice straw can be used as bioenergy. Rice straw pellets are a promising technology because pelletization of rice straw is a form of mass and energy densification, which leads to a product that is easy to handle, transport, store and utilize because of the increase in the bulk density. The operational conditions required to produce high quality rice straw pellets have not been determined. This study determined the optimal moisture content range required to produce rice straw pellets with high yield ratio and high heating value, and also determined the influence of particle size and the forming temperature on the yield ratio and durability of rice straw pellets. The optimal moisture content range was between 13% and 20% under a forming temperature of 60 or 80 °C. The optimal particle size was between 10 and 20 mm, considering the time and energy required for shredding, although the particle size did not significantly affect the yield ratio and durability of the pellets. The optimized conditions provided high quality rice straw pellets with nearly 90% yield ratio, ?12 MJ/kg for the lower heating value, and >95% durability.     

催化氧化处理苯化工装置和罐区含氮挥发性有机物废气

采用自行研制的WSH-2N型蜂窝状Pt-Pd-Ce催化剂,对某企业苯胺、硝基苯等生产装置和罐区的含氮挥发性有机物(NVOCs)废气进行集中处理,考察了废气处理工业装置的运行效果。在小型装置上处理后总烃去除率大于97%,净化气总烃质量浓度小于20 mg/m~3,NO_x质量浓度小于30 mg/m~3,苯胺、硝基苯中氮转化为N2的选择性大于95%。20 000 Nm~3/h催化氧化处理装置生产运行和性能考核表明,苯化工装置和罐区VOCs废气经过催化氧化处理,非甲烷总烃去除率大于99%;净化气中非甲烷总烃质量浓度小于10 mg/m~3,苯、苯胺、硝基苯、环己烷等有机特征污染物均低于检出限,NO_x的质量浓度小于10 mg/m~3。     

Solid-state anaerobic co-digestion of food waste,rice straw,and rice husk supplemented with cattle digesta under thermophilic conditions

Journal of Material Cycles and Waste Management - Improving the solid-state digestion of food waste (FW) is important for recovering energy and utilizing the digested residue as fertilizer. Herein,...     

Influence of liquid- and solid-state coupling anaerobic digestion process on methane production of cow manure and rice straw

Journal of Material Cycles and Waste Management - Based on the different characteristics of cow manure and rice straw, liquid- and solid-state coupling anaerobic digestion (L-SS-AD) is designed in...     

The mixing and segregation characteristics of rice straw in a cylindrical bubbling fluidized bed

In the present study, an experiment was performed to investigate the mixing and segregation characteristics of standard sand and rice straw particles in a cylindrical bubbling fluidized bed. The mass ratio (rice straw/standard sand = 0.5–1.25 %) of two particles and superficial gas velocity (0.13–0.18 m/s) were changed as experimental variables. The pressure drop curve and Kramer’s equation were used to determine the minimum fluidization velocity and mixing index, respectively. In all cases, the mixing index was the lowest at U/U _mf = 1.15. Based on the point of U/U _mf = 1.15, the segregation region and mixing region were observed. In the segregation region, mass ratio of 0.75 % showed the lowest mixing index. At the U/U _mf = 1.23 which was selected as the starting of fast pyrolysis considering residence time and the previous fast pyrolysis experiment, mass ratio of 1.25 % showed the highest mixing index which was 0.90.     

Co-composting of livestock manure with rice straw: Characterization and establishment of maturity evaluation system

Composting is considered to be a primary treatment method for livestock manure and rice straw, and high degree of maturity is a prerequisite for safe land application of the composting products. In this study pilot-scale experiments were carried out to characterize the co-composting process of livestock manure with rice straw, as well as to establish a maturity evaluation index system for the composts obtained. Two pilot composting piles with different feedstocks were conducted for 3 months: (1) swine manure and rice straw (SM–RS); and (2) dairy manure and rice straw (DM–RS). During the composting process, parameters including temperature, moisture, pH, total organic carbon (TOC), organic matter (OM), different forms of nitrogen (total, ammonia and nitrate), and humification index (humic acid and fulvic acid) were monitored in addition to germination index (GI), plant growth index (PGI) and Solvita maturity index. OM loss followed the first-order kinetic model in both piles, and a slightly faster OM mineralization was achieved in the SM–RS pile. Also, the SM–RS pile exhibited slightly better performance than the DM–RS according to the evolutions of temperature, OM degradation, GI and PGI. The C/N ratio, GI and PGI could be included in the maturity evaluation index system in which GI > 120% and PGI > 1.00 signal mature co-composts.     

催化氧化技术治理苯化工装置和罐区含氮挥发性有机物废气

采用催化氧化技术对某石化企业苯胺、硝基苯等生产装置和罐区的含氮挥发性有机物(NVOCs)废气进行集中处理,建成了一套20 000 Nm~3/h规模的安全高效处理装置。采用自主研发的WSH-2N型蜂窝状Pt-Pd-Ce催化剂,在高效氧化有机物的同时,高选择性地将有机氮转化为N_2。运行结果表明,净化气非甲烷总烃质量浓度低于15 mg/m~3,非甲烷总烃去除率大于99%,NO_x质量浓度低于10 mg/m~3,苯、苯胺、硝基苯、环己烷等特征有机污染物浓度均低于检出限,各项指标优于国内外现有技术。     

Characterization of cellulosic wastes and gasification products from chicken farms

The current article focuses on gasification as a primary disposal solution for cellulosic wastes derived from chicken farms, and the possibility to recover energy from this process. Wood shavings and chicken litter were characterized with a view to establishing their thermal parameters, compositional natures and calorific values. The main products obtained from the gasification of chicken litter, namely, producer gas, bio-oil and char, were also analysed in order to establish their potential as energy sources. The experimental protocol included bomb calorimetry, pyrolysis combustion flow calorimetry (PCFC), thermo-gravimetric analyses (TGA), differential scanning calorimetry (DSC), Fourier transform infrared (FT-IR) spectroscopy, Raman spectroscopy, elemental analyses, X-ray diffraction (XRD), mineral content analyses and gas chromatography. The mass and energy balances of the gasification unit were also estimated. The results obtained confirmed that gasification is a viable method of chicken litter disposal. In addition to this, it is also possible to recover some energy from the process. However, energy content in the gas-phase was relatively low. This might be due to the low energy efficiency (19.6%) of the gasification unit, which could be improved by changing the operation parameters.