Effect of Coconut, Sisal and Jute Fibers on the Properties of Starch/Gluten/Glycerol Matrix

Coconut, sisal and jute fibers were added as reinforcement materials in a biodegradable polymer matrix comprised of starch/gluten/glycerol. The content of fibers used in the composites varied from 5% to 30% by weight of the total polymers (starch and gluten). Materials were processed in a Haake torque rheometer (120 °C, 50 rpm) for 6 min. The mixtures obtained were molded by heat compression and further characterized. Addition of lignocellulosic fibers in the matrix decreased the water absorption at equilibrium. The diffusion coefficient decreased sharply around 5% fiber concentration, and further fiber additions caused only small variations. The thermogravimetric (TG) analysis revealed improved thermal stability of matrix upon addition of fibers. The Young’s modulus and ultimate tensile strength increased with fiber content in the matrix. The storage modulus increased with increasing fiber content, whereas tanδ curves decreased, confirming the reinforcing effect of the fibers. Morphology of the composites analyzed under the scanning electron microscope (SEM) exhibited good interfacial adhesion between the matrix and the added fibers. Matrix degraded rapidly in compost, and addition of increased amounts of coconut fiber in the matrix caused a slowdown the biodegradability of the matrix. Names are necessary to report factually on available data; however, the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA implies no approval of the product to the exclusion of others that may be suitable.     

Effect of Cotton Fiber Contents and Lengths on Properties of Thermoplastic Starch Composites Prepared from Rice and Waxy Rice Starches

Biodegradable polymer was prepared as thermoplastic starch (TPS) using rice and waxy rice starches. In order to increase mechanical properties and reduce water absorption of the TPS, cotton fiber was incorporated as the fiber reinforcement into the TPS matrix. The effect of cotton fiber contents and lengths on properties of the TPS was examined. Internal mixer and compression molding machine were used to mix and shape the samples. It was found that the thermoplastic rice starch (TPRS) showed higher stress at maximum load and Young’s modulus but lower strain at maximum load than the thermoplastic waxy rice starch (TPWRS). In addition, stress at maximum load and Young’s modulus of both TPRS and TPWRS increased significantly with the addition of the cotton fiber. Cotton fiber contents and lengths also affected mechanical properties of the TPRS and TPWRS composites. Moreover, water absorption of the TPRS and TPWRS composites decreased by the use of the cotton fibers. FT-IR and XRD techniques were used to study a change in functional group and crystallinity of the thermoplastic starch composites. Morphological, thermal and biodegradable properties of different thermoplastic starch composites were also investigated.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Mechanical Properties of Poly (Lactic Acid)/Hemp Fiber Composites Prepared with a Novel Method

This research dealt with a novel method of fabricating green composites with biodegradable poly (lactic acid) (PLA) and natural hemp fiber. The new preparation method was that hemp fibers were firstly blending-spun with a small amount of PLA fibers to form compound fiber pellets, and then the traditional twin-screw extruding and injection-molding method were applied for preparing the composites containing 10–40 wt% hemp fibers with PLA pellets and compound fiber pellets. This method was very effective to control the feeding and dispersing of fibers uniformly in the matrix thus much powerful for improving the mechanical properties. The tensile strength and modulus were improved by 39 and 92 %, respectively without a significant decrease in elongation at break, and the corresponding flexural strength and modulus of composites were also improved by 62 and 90 %, respectively, when the hemp fiber content was 40 wt%. The impact strength of composite with 20 wt% hemp fiber was improved nearly 68 % compared with the neat PLA. The application of the silane coupling agent promoted further the mechanical properties of composites attributed to the improvement of interaction between fiber and resin matrix.     

A Comparison Study of Wheat Gluten Composites Filled with Dialdehyde Starch and Native Starch

Environmentally friendly green composites were prepared by blending Wheat gluten (WG) as matrix, dialdehyde starch (DAS) as filler and glycerol as plasticizer followed by compression molding of the mixture at 110 °C. The properties of the WG/DAS composite are compared with those of the WG/native wheat starch (NWS) composites. While tensile strength and strain at break decrease with increasing NWS content in the WG/NWS composites, a small content of DAS could improve tensile strength and strain at break simultaneously in the WG/DAS composites. The WG/DAS composites exhibit reduced moisture absorption in comparison with the WG/NEW composites. Formation of chemical bonding between DAS and WG is beneficial for the dispersion of DAS in the WG matrix and WG/DAS composites exhibit improved mechanical properties and reduced moisture absorption over the WG/NWS composites.     

Soda-Treated Sisal/Polypropylene Composites

Treated sisal fibers were used as reinforcement of polypropylene (PP) composites, with maleic anhydride-grafted PP (MAPP) as coupling agent. The composites were made by melting processing of PP with the fiber in a heated roller followed by multiple extrusions in a single-screw extruder. Injection molded specimens were produced for the characterization of the material. In order to improve the adhesion between fiber and matrix and to eliminate odorous substances, sisal fibers were treated with boiling water and with NaOH solutions at 3 and 10 wt.%. The mechanical properties of the composites were assessed by tensile, bend and impact tests. Additionally, the morphology of the composites and the adhesion at he fiber–matrix interface were analyzed by SEM. The fiber treatment led to very light and odorless materials, with yields of 95, 74 and 62 wt.% for treatments with hot water, 3 and 10 wt.% soda solution respectively. Fiber treatment caused an appreciable change in fiber characteristics, yet the mechanical properties under tensile and flexural tests were not influenced by that treatment. Only the impact strength increased in the composites with alkali-treated sisal fibers.     

Influence of Hygrothermal Ageing on the Physico-Mechanical Properties of Alkali Treated Industrial Hemp Fibre Reinforced Polylactic Acid Composites

30 wt% aligned untreated long hemp fibre/polylactic acid (AUL) and aligned alkali treated long hemp fibre/polylactic acid (AAL) composites were produced by film stacking and subjected to hygrothermal ageing environment along with neat polylactic acid (PLA). Hygrothermal ageing was carried out by immersing samples in distilled water at 25 and 50 °C over a period of 3 months. It was found that both neat PLA and composites followed Fickian diffusion. Higher temperature generally increased the Diffusion coefficient, D of neat PLA and composites, as well as shortening the saturation time. Neat PLA had the lowest D value followed by AAL composites and then AUL composites. After hygrothermal ageing, tensile and flexural strength, Young’s and flexural modulus and K _Ic were found to decrease and impact strength was found to increase for both AUL and AAL composites. AUL composites had greater overall reduction in mechanical properties than that for AAL composites after hygrothermal ageing. Crystallinity contents of the hygrothermal aged composites support the results of the deterioration of mechanical properties upon exposure to hygrothermal ageing environment.     

Lightweight Polypropylene Composites Reinforced by Long Switchgrass Stems

Switchgrass (SG) stems with lengths up to 10 cm have been used as reinforcement to make lightweight composites with polypropylene (PP) webs. The long SG stems, with simple cut or split and without chemical treatment, were used directly in the composites. Utilizing SG stems for composites not only increases the values of SG but also provides a green, sustainable and biodegradable material for the composites industry. Lightweight composites are preferred, especially for automotive applications due to the potential saving in energy. In this research, the effects of manufacturing parameters on the properties of composites have been studied. Although the tensile properties of SG stem are significantly worse than jute fiber, SG stem with low bulk density is found to better reinforce the lightweight composites. Compared with the jute-PP composites of the same density (0.47 g/cm³), composites reinforced by the split SG stems have 56% higher flexural strength, 19% higher modulus of elasticity, 15% higher impact resistance, 63% higher Young’s modulus, 52% lower tensile strength, and similar sound absorption property. The SG-PP composites with optimized properties have the potential to be used for industrial applications such as the support layers in automotive interiors, office panels and ceiling tiles.     

Analysis of Flax and Cotton Fiber Fabric Blends and Recycled Polyethylene Composites

Manufacturing composites with polymers and natural fibers has traditionally been performed using chopped fibers or a non-woven mat for reinforcement. Fibers from flax (Linum usitatissimum L.) are stiff and strong and can be processed into a yarn and then manufactured into a fabric for composite formation. Fabric directly impacts the composite because it contains various fiber types via fiber or yarn blending, fiber length is often longer due to requirements in yarn formation, and it controls the fiber alignment via weaving. Composites created with cotton and flax-containing commercial fabrics and recycled high-density polyethylene (HDPE) were evaluated for physical and mechanical properties. Flax fiber/recycled HDPE composites were easily prepared through compression molding using a textile preform. This method takes advantage of maintaining cotton and flax fiber lengths that are formed into a yarn (a continuous package of short fibers) and oriented in a bidirectional woven fabric. Fabrics were treated with maleic anhydride, silane, enzyme, or adding maleic anhydride grafted polyethylene (MAA-PE; MDEX 102-1, Exxelor^® VA 1840) to promote interactions between polymer and fibers. Straight and strong flax fibers present problems because they are not bound as tightly within yarns producing weaker and less elastic yarns that contain larger diameter variations. As the blend percentage and mass of flax fibers increases the fabric strength, and elongation generally decrease in value. Compared to recycled HDPE, mechanical properties of composite materials (containing biodegradable and renewable resources) demonstrated significant increases in tensile strength (1.4–3.2 times stronger) and modulus of elasticity (1.4–2.3 times larger). Additional research is needed to improve composite binding characteristics by allowing the stronger flax fibers in fabric to carry the composites load.     

Injection Molded Biocomposites from Soy Protein Based Bioplastic and Short Industrial Hemp Fiber

Biocomposites from soy based bioplastic and chopped industrial hemp fiber were fabricated using twin-screw extrusion and injection molding process. Soy based bioplastics were prepared through cooking with plasticizer and blending with biodegradable poly(ester amide). Mechanical, thermal properties and fracture surface morphology of the “green”/biocomposites were evaluated with universal testing system (UTS), dynamic mechanical analysis (DMA), Environmental Scanning Electron Microscopy (ESEM). It was found that the tensile strength and modulus, flexural strength and modulus, impact strength and heat deflection temperature of industrial hemp fiber reinforced biocomposites significantly improved. The fracture surfaces showed no signs of matrix on the fiber surface suggesting poor interfacial adhesion.     

Reactively Compatibilized Cellulosic Polylactide Microcomposites

Poly(lactic acid) (PLA) possesses a suite of favorable material properties that are enabling its penetration into diverse markets (e.g., as packaging material or textile fibers). In order to increase the range of applications for this material, it is necessary to modify its properties and for certain applications, reduce its cost. The introduction of fibers into a polymeric matrix is an established route towards property enhancement provided good dispersion and intimate interfacial adhesion can be achieved. In addition, cellulosic microfibers are obtainable at low to moderate cost. In this study, reactive compatibilization of cellulosic fibers with PLA is pursued. Hydroxyl groups available on the surface of cellulosic fibers are used to initiate lactide polymerization. Various processing strategies are investigated: (1) blending preformed PLA with the fiber material, (2) through a one-step process in which lactide is polymerized in the presence of the fibers alone, or (3) reactive compatibilization in the presence of preformed high molecular weight polymer. The results show that materials prepared by simultaneous introduction of lactide and preformed high molecular PLA at the beginning of the reaction possess superior mechanical properties compared to composites made by either purely mechanical mixing or solely polymerization of lactide in the presence of fibers. The modulus of materials containing 25% fibers which are prepared by reactive compatibilization of 30% preformed PLA and 70% lactide (30/70 P/L) improves by 53% compared to the homopolymer, whereas 36% reinforcement can be achieved upon purely mechanical mixing. A further increase to 35% fiber loading leads to a reduction in modulus due to an excess in initiating groups. The same trend was observed in systems containing 65% preformed PLA and 35% lactide (65/35 P/L) with an overall achievable reinforcement that was slightly lower.     

Effects of Alkali Treatment on the Properties of Short Flax Fiber–Poly(Lactic Acid) Eco-Composites

In this study, the influence of alkali (NaOH) treatment on the mechanical, thermal and morphological properties of eco-composites of short flax fiber/poly(lactic acid) (PLA) was investigated. SEM analysis conducted on alkali treated flax fibers showed that the packed structure of the fibrils was deformed by the removal non-cellulosic materials. The fibrils were separated from each other and the surface roughness of the alkali treated flax fibers was improved. The mechanical tests indicated that the modulus of the untreated fiber/PLA composites was higher than that of PLA; on the other hand the modulus of alkali treated flax fiber/PLA was lower than PLA. Thermal properties of the PLA in the treated flax fiber composites were also affected. T_g values of treated flax fiber composites were lowered by nearly 10 °C for 10% NaOH treatment and 15 °C for 30% NaOH treatment. A bimodal melting behavior was observed for treated fiber composites different than both of neat PLA and untreated fiber composites. Furthermore, wide angle X-ray diffraction analysis showed that the crystalline structure of cellulose of flax fibers changed from cellulose-I structure to cellulose-II.     

Molding Method, Thermal and Mechanical Properties of Jute/PLA Injection Molding

Natural composites have been important materials system due to preservation of earth environments. Natural fibers such as jute, hemp, bagasse and so on are very good candidate of natural composites as reinforcements. On the other hand regarding matrix parts thermosetting polymer and thermoplastic polymer deriver form petrochemical products are not environmental friendly material, even if thermoplastic polymer can be recycled. In order to create fully environmental friendly material (FEFM) biodegradable polymer which can be deriver from natural resources is needed. Therefore poly(lactic acid) (PLA) polymer is very good material for the FEFM. In this paper jute fiber filled PLA resin (jute/PLA) composites was fabricated by injection moldings and mechanical properties were measured. It is believable that industries will have much attention to FEFM, so that injection molding was adopted to fabricate the composites. Long fiber pellet fabricated by pultrusion technique was adopted to prepare jute/PLA pellet. Because it is able to fabricate composite pellets with relative long length fibers for injection molding process, where, jute yarns were continuously pulled and coated with PLA resin. Here two kinds of PLA materials were used including the one with mold releasing agent and the other without it. After pass through a heated die whereby PLA resin impregnates into the jute yarns and sufficient cooling, the impregnated jute yarns were cut into pellets. Then jute/PLA pellets were fed into injection machine to make dumbbell shape specimens. In current study, the effects of temperature of PLA melting temperature i.e. impregnation temperature and the kinds of PLA were focused to get optimum molding condition. The volume fractions of jute fiber in pellet were measured by several measuring method including image analyzing, density measurement and dissolution methods. Additionally, thermal and mechanical properties were investigated. It is found that 250° is much suitable for jute/PLA long fiber pultrusion process because of its less heat degradation of jute, better impregnation, acceptable mechanical property and higher production efficiency. Additionally the jute fibers seem much effective to increase deflection temperature under load, tensile modulus and Izod strength.     

Preparation and Properties of Green Composites Based on Tapioca Starch and Differently Recycled Paper Cellulose Fibers

Green composites obtained from biodegradable renewable resources have gained much attention due to environmental problems resulting from conventionally synthetic plastics and a global increasing demand for alternatives to fossil resources. In this work we used different cellulose fibers from used office paper and newspaper as reinforcement for thermoplastic starch (TPS) in order to improve their poor mechanical, thermal and water resistance properties. These composites were prepared by using tapioca starch plasticized by glycerol (30 % wt/wt of glycerol to starch) as matrix reinforced by the extracted cellulose fibers with the contents ranging from 0 to 8 % (wt/wt of fibers to matrix). Properties of composites were determined by mechanical tensile tests, differential scanning calorimetry, thermogravimetric analysis, water absorption measurements, scanning electron microscopy, and soil burial tests. The results showed that the introduction of either office paper or newspaper cellulose fibers caused the improvement of tensile strength and elastic modulus, thermal stability, and water resistance for composites when compared to the non-reinforced TPS. Scanning electron microscopy showed a good adhesion between matrix and fibers. Moreover, the composites biological degraded completely after 8 weeks but required a longer time compared to the non-reinforced TPS. The results indicated that these green composites could be utilized as commodity plastics being strong, inexpensive, plentiful and recyclable.     

Bio-based composites from waste agricultural residues

The main objective of this research was to study the potential of waste agricultural residues such as sunflower stalk, corn stalk and bagasse fibers as reinforcement for thermoplastics as an alternative to wood fibers. The effects of two grades (Eastman G-3003 and G-3216) of coupling agents on the mechanical properties were also studied. In the sample preparation, one level of fiber loading (30 wt.%) and three levels of coupling agent content (0, 1.5 and 2.5 wt.%) were used. For overall trend, with addition of both grades of the coupling agents, tensile, flexural and impact properties of the composites significantly improved, as compared with untreated samples. In addition, morphological study revealed that the positive effect of coupling agent on interfacial bonding. The composites treated with G-3216 gave better results in comparison with G-3003. This could be caused by the high melt viscosity of G-3003. In general, bagasse fiber showed superior mechanical properties due to its chemical characteristics.     

Biopolymers Based Green Composites: Mechanical, Thermal and Physico-chemical Characterization

Natural cellulosic fibers are one of the smartest materials for use as reinforcement in polymers possessing a number of applications. Keeping in mind the immense advantages of the natural fibers, in present work synthesis of natural cellulosic fibers reinforced polymer composites through compression molding technique have been reported. Scanning Electron microscopy (SEM), Thermo gravimetric/Differential thermal/Derivative Thermogravimetry (TGA/DTA/DTG), absorption in different solvents, moisture absorbance, water uptake and chemical resistance measurements were used as characterization techniques for evaluating the different behaviour of cellulosic natural fibers reinforced polymer composites. Effect of fiber loading on mechanical properties like tensile strength, flexural strength, compressive strength and wear resistances has also been determined. Reinforcing of the polymer matrix with natural fibers was done in the form of short fiber. Present work indicates that green composites can be successfully fabricated with useful mechanical properties. These composites may be used in secondary structural applications in automotive, housing etc.     

Comparison of Polylactic Acid/Kenaf and Polylactic Acid/Rise Husk Composites: The Influence of the Natural Fibers on the Mechanical, Thermal and Biodegradability Properties

This paper investigates and compares the performances of polylactic acid (PLA)/kenaf (PLA-K) and PLA/rice husk (PLA-RH) composites in terms of biodegradability, mechanical and thermal properties. Composites with natural fiber weight content of 20% with fiber sizes of less than 100 μm were produced for testing and characterization. A twin-screw extrusion was used to compound PLA and natural fibers, and extruded composites were injection molded to test samples. Flexural and Izod impact test, TGA, soil burial test and SEM were used to investigate properties. All results were compared to a pure PLA matrix sample. The flexural modulus of the PLA increased with the addition of natural fibers, while the flexural strength decreased. The highest impact strength (34 J m⁻¹), flexural modulus (4.5 GPa) and flexural strength (90 MPa) were obtained for the composite made of PLA/kenaf (PLA-K), which means kenaf natural fibers are potential to be used as an alternative filler to enhance mechanical properties. On the other hand PLA-RH composite exhibits lower mechanical properties. The impact strength of PLA has decreased when filled with natural fibers; this decrease is more pronounced in the PLA-RH composite. In terms of thermal stability it has been found that the addition of natural fibers decreased the thermal stability of virgin PLA and the decrement was more prominent in the PLA-RH composite. Biodegradability of the composites slightly increased and reached 1.2 and 0.8% for PLA-K and PLA-RH respectively for a period of 90 days. SEM micrographs showed poor interfacial between the polymer matrix and natural fibers.     

Thermal and mechanical properties of poly(lactic Acid) and poly(ethylene/butylene Succinate) blends

In this study, blends of poly (lactic acid) (PLA) with poly(ethylene/butylene succinate) (Bionolle) have been investigated for their thermal and mechanical properties as a function of the concentration of Bionolle. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and tensile tests were used to characterize the blends. From the results of the DMA and DSC, it was found that this blend system was not miscible within the compositions studied. DSC results showed that adding Bionolle aids in crystallization of PLA. It was observed that increasing the Bionolle concentration led to a slight increase in the strain-at-break of the blends but a decrease in the Young’s modulus and ultimate tensile strength. Biaxially oriented films showed an increase in tensile strength, modulus, and strain-at-break.     

Properties of Distillers Grains Composites: A Preliminary Investigation

Interest in renewable biofuel sources has intensified in recent years, leading to greatly increased production of ethanol and its primary coproduct, Distillers Dried Grain with Solubles (DDGS). Consequently, the development of new outlets for DDGS has become crucial to maintaining the economic viability of the industry. In light of these developments, this preliminary study aimed to determine the suitability of DDGS for use as a biofiller in low-cost composites that could be produced by rapid prototyping applications. The effects of DDGS content, particle size, curing temperature, and compression on resulting properties, such as flexural strength, modulus of elasticity, water activity, and color were evaluated for two adhesive bases. The composites formed with phenolic resin glue were found to be greatly superior to glue in terms of mechanical strength and durability: resin-based composites had maximum fiber stresses of 150–380 kPa, while glue composites had values between 6 kPa and 35 kPa; additionally, glue composites experienced relatively rapid microbial growth. In the resin composites, both decreased particle size and increased compression resulted in increased mechanical strength, while a moderate DDGS content was found to increase flexural strength but decrease Young’s modulus. These results indicate that DDGS has the potential to be used in resin glue-based composites to both improve flexural strength and improve potential biodegradability.     

Mechanical Properties of Kenaf/Polypropylene Nonwoven Composites

With an industrial trend of going green, the use of natural fibers in polymer composites is growing rapidly, especially in the automotive industry. The objectives of this research are to investigate mechanical performance of kenaf/polypropylene nonwoven composites (KPNCs) in production of automotive interior parts, and to develop preliminary linear models for quantifying elastic range of the KPNCs under various loading conditions. Using polypropylene (PP) fiber as bonding fiber, the KPNCs were fabricated with 50/50 blend ratio by weight. Unlike the manufacturing method of fiber reinforced plastics, all KPNCs were produced by carding and needle-punching techniques and thermally bonded by a panel press with 3-mm thickness gauge. Mechanical properties of the KPNCs in terms of uniaxial tensile, open-hole tensile, tensile at different strain rates, flexural, and in-plane shear were measured instrumentally. It was found that sample which was processed at higher temperature (230?°C) but shorter time (60?s) had the best mechanical performance. KPNCs were relatively insensitive to the notch but sensitive to strain rates. The linear elastic finite element model of KPNCs agreed well with the experimental results in the valid strain range of 0?C0.5?% for uniaxial tensile test and 0?C1?% for flexural test.