Mathematical model for photocatalytic destruction of organic contaminants in air

Photocatalytic oxidation (PCO) was investigated in a bench-scale reactor for the abatement of two airborne organic contaminants: toluene and ethanol. A mathematical model that includes the impacts of light intensity, initial contaminant concentration, catalyst thickness, and relative humidity (RH) on the degradation of organic contaminants in a photocatalytic reactor was developed to describe this process. The commercially available catalyst Degussa-PtTiO2 was selected to compare with the MTU-PtTiO2-350 catalyst, which was synthesized by the sol-gel process, platinized, and calcined at 350 degrees C. For toluene removal using the MTU-PtTiO2-350 catalyst, the degradation rate increased with increases in light intensity from 0.2 to 2.2 mW/cm2 and in catalyst thickness from 0.00037 to 0.00361 cm. However, further increases in light intensity and catalyst thickness had only slight effect on the toluene degradation rate. Increasing the initial concentration from 6.29 to 127.9 microg/L and the RH from 10 to 85% resulted in decreases in the toluene degradation rate. For ethanol removal using the MTU-PtTiO2-350 catalyst, the degradation rate increased more rapidly with an increase in RH from 17 to 56%; the RH had little effect on the ethanol degradation rate while it further increased from 56% to 82%. We discuss applicability of the model to estimate the influence of process variables and to evaluate photocatalyst performance.     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO₂作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO₂催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO₂的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO₂溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37％;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

光催化降解模拟室内挥发性有机污染物研究

用浸渍-提拉法制备玻璃弹簧负载型TiO2薄膜催化剂,在自制的反应器中进行光催化降解由丙酮、甲苯、对二甲苯组成的模拟室内挥发性有机污染物VOCs研究.研究发现:催化剂中掺杂金属离子能影响催化剂的降解效果,降解效果依次为掺铈TiO2＞纯TiO2＞掺银TiO2;气体流量显著影响降解效果,丙酮、甲苯和对二甲苯的最佳降解流量分别为3、5、7 L/min;混合气体中非对称性的极性分子的降解效率高于对称性分子,导致丙酮、对二甲苯组分降解率降低,甲苯降解率增高.     

活性炭吸附和脱附-等离子体氧化净化有机废气的研究

根据滑动弧放电等离子体适于降解高浓度有机物废气的特性,结合活性炭吸附法,提出了吸附器的吸附浓缩和热脱附-等离子体氧化净化有机废气的方法。在活性炭吸附过程中,最初2 h内甲苯净化率达到100%,随着时间的增加净化率下降;在热脱附滑动弧放电等离子体净化过程中,甲苯降解效率最高为97.3%。将滑动弧放电等离子体反应器出口气相产物收集进行FT-IR检测,发现放电后有CO2、CO、H2O和NO2产生,并分析了甲苯的降解机理。     

Macro kinetic studies for photocatalytic degradation of benzoic acid in immobilized systems

Semiconductor photocatalytic process has been studied extensively in recent years due to its intriguing advantages in environmental remediation. In this study, a two-phase swirl-flow monolithic-type reactor is used to study the kinetics of photocatalytic degradation of benzoic acid in immobilized systems. Transport contributions into the observed degradation rates were determined when catalyst is immobilized. Intrinsic kinetic rate constants and its dependence on light intensity and catalyst layer thickness, values of adsorption equilibrium constant, internal as well as external mass transfer parameters were determined. The simultaneous effect of catalyst loading and light intensity and optimum catalyst layer thickness were also determined experimentally. Reaction rate constants and overall observed degradation rates were compared with slurry systems.     

Photocatalytic oxidation of xenobiotics in water with immobilized TIO2 on agitator

Abstract

A novel photocatalytic oxidation reactor, using Degussa P‐25 T_iO₂ as a stationary phase with a thickness of 1.5–2.0 um on the blades of agitator, was developed to study the photocatalytic oxidation of xenobiotics. Particularly in this device, separation of photocatalyst from the purified water after oxidation reaction was not necessary, and no other aeration equipment was required to supply oxygen. To examine the efficiency of this device, photocatalytic degradation of xenobiotic organics such as carbofuran was studied as an example. Results indicated that carbofuran could be degraded completely with mineralization efficiency of 20 % after 6 hours of oxidation under the imposed conditions. The mineralization rate of carbofuran was found to follow the pseudo‐first order reaction kinetics. Moreover, the rate constant of mineralization was found to be proportional to T_iO₂ film area and the square root of UV light intensity. These results implied the mineralization efficiency of carbofuran could be improved through increasing T_iO₂ film area and UV light intensity. Accordingly, this novel device showed potential application for degrading xenobiotics in water.     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

Photocatalytic degradation of phenol using Ag core-TiO<Subscript>2</Subscript> shell (Ag@TiO<Subscript>2</Subscript>) nanoparticles under UV light irradiation

Ag@TiO₂ nanoparticles were synthesized by one pot synthesis method with postcalcination. These nanoparticles were tested for their photocatalytic efficacies in degradation of phenol both in free and immobilized forms under UV light irradiation through batch experiments. Ag@TiO₂ nanoparticles were found to be the effective photocatalysts for degradation of phenol. The effects of factors such as pH, initial phenol concentration, and catalyst loading on phenol degradation were evaluated, and these factors were found to influence the process efficiency. The optimum values of these factors were determined to maximize the phenol degradation. The efficacy of the nanoparticles immobilized on cellulose acetate film was inferior to that of free nanoparticles in UV photocatalysis due to light penetration problem and diffusional limitations. The performance of fluidized bed photocatalytic reactor operated under batch with recycle mode was evaluated for UV photocatalysis with immobilized Ag@TiO₂ nanoparticles. In the fluidized bed reactor, the percentage degradation of phenol was found to increase with the increase in catalyst loading.     

APCA Financial Statements for FY 1981–82

ABSTRACT

The objective of this study was to determine whether ultraviolet-light-emitting diodes (UV-LEDs) could serve as an efficient photon source for heterogeneous photocatalytic oxidation (PCO). An LED module consisting of 12 high-power UV-A (λ_max?=?365 nm) LEDs was designed to be interchangeable with a UV-A fluorescent black light blue (BLB) lamp for a bench scale annular reactor packed with silica-titania composite (STC) pellets. Lighting and thermal properties of the module were characterized to assess its uniformity and total irradiance. A forward current (I _F) of 100 mA delivered an average irradiance of 4.0 mW cm^?2 at a distance of 8 mm, which is equivalent to the maximum output of the BLB, but the irradiance of the LED module was less uniform than that of the BLB. The LED and BLB reactors were tested for the oxidization of ethanol (50 ppm_v) in a continuous-flow-through mode with 0.94 sec residence time. At the same average irradiance, the UV-A LED reactor resulted in a lower CO₂ production rate (19.8 vs. 28.6 nmol L^?1 s^?1), lower ethanol removal (80% vs. 91%), and lower mineralization efficiency (28% vs. 44%) than the UV-A BLB reactor. Ethanol mineralization was enhanced with the increase of the irradiance at the catalyst surface. This result suggests that reduced ethanol mineralization in the LED reactor relative to the BLB reactor at the same average irradiance could be attributed to the nonuniform irradiance over the photocatalyst, that is, a portion of the catalyst was exposed to less than the average irradiance. The potential of UV-A LEDs may be fully realized by optimizing the light distribution over the catalyst and utilizing their instantaneous “on” and “off” feature for periodic irradiation. Nevertheless, our results also showed that the current UV-A LED module had the same wall plug efficiency (WPE) of 13% as that of the UV-A BLB, demonstrating that UV-A LEDs are a viable photon source both in terms of WPE and PCO efficiency.

IMPLICATIONS Mercury (Hg)-vapor lamps are common UV sources for photocatalysis but create safety and environmental concerns because they contain Hg; furthermore, they have a relatively short life span. This paper demonstrated that the UV-A LED is a viable alternative to the Hg-vapor lamps without sacrificing PCO efficiency if the design of the LED arrays is improved to increase the lighting uniformity. The use of LEDs could eliminate hazardous Hg wastes and extend the application of photocatalysis in places requiring more compact and robust air purification solutions.     

Carbofuran removal in continuous-photocatalytic reactor: Reactor optimization,rate-constant determination and carbofuran degradation pathway analysis

Carbofuran (CBF) removal in a continuous-flow photocatalytic reactor with granular activated carbon supported titanium dioxide (GAC-TiO₂) catalyst was investigated. The effects of feed flow rate, TiO₂ concentration and addition of supplementary oxidants on CBF removal were investigated. The central composite design (CCD) was used to design the experiments and to estimate the effects of feed flow rate and TiO₂ concentration on CBF removal. The outcome of CCD experiments demonstrated that reactor performance was influenced mainly by feed flow rate compared to TiO₂ concentration. A second-order polynomial model developed based on CCD experiments fitted the experimental data with good correlation (R² ～ 0.964). The addition of 1 mL min^?1 hydrogen peroxide has shown complete CBF degradation and 76% chemical oxygen demand removal under the following operating conditions of CBF ～50 mg L^?1, TiO₂ ～5 mg L^?1 and feed flow rate ～82.5 mL min^?1. Rate constant of the photodegradation process was also calculated by applying the kinetic data in pseudo-first-order kinetics. Four major degradation intermediates of CBF were identified using GC-MS analysis. As a whole, the reactor system and GAC-TiO₂ catalyst used could be constructive in cost-effective CBF removal with no impact to receiving environment through getaway of photocatalyst.     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶凝胶法制备TiO₂/beads光催化剂载体,然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

氮掺杂二氧化钛可见光催化降解曙红Y溶液

采用溶胶凝胶法制备了氮掺杂二氧化钛光催化剂,用XRD、SEM、FTIR和粒度分析仪对催化剂进行了表征,并且在可见光作用下对曙红Y溶液进行了光催化降解实验。研究了催化剂的投加量、曙红Y的初始浓度、光照时间和pH对曙红Y溶液的光降解效果。结果表明,以可见光作光源,催化剂的投入量为0.4 g,曙红Y溶液的初始浓度为20 mg/L,光照时间为50 min,pH=4条件下,曙红Y溶液的降解率达98.87%。     

氮掺杂TiO_2可见光光催化剂的制备及性能

以尿素和钛酸丁酯为原料,通过溶胶-凝胶法低温下制备了高可见光催化活性的氮掺杂TiO2（NDT）光催化剂,采用XRD、TEM、BET和UV-Vis DRS等测试手段对其进行了表征,并在自制光催化反应器中降解甲基橙评价了样品的光催化活性。结果表明,当氮与钛的摩尔比为0.5∶1时,350℃焙烧的样品（NDT350）具有最佳的可见光光谱吸收和光催化活性,该催化剂为锐钛矿晶相,平均粒径为21 nm,比表面积为89.13 m2/g。可见光辐照下,NDT350降解甲基橙的表观反应速率常数为1.381×10-2min-1,是商业P25催化剂的16.85倍。NDT350优良的可见光催化活性与其大的比表面积和强烈的可见光光谱吸收有关。     

活性炭纤维负载TiO_2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响.结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%.     

黄铁矿催化H2O2氧化降解水中三氯生

以三氯生为目标污染物,研究了黄铁矿催化H2O2非均相类Fenton体系对污染物的去除效果,并利用SEM、EDS等手段对天然黄铁矿进行了表征。考察了催化剂、H2O2投加量、溶液初始pH、反应时间等重要因素对催化氧化反应的影响。在H2O2投加量5 mg/L,黄铁矿用量0.1 g/L,溶液初始pH为8,反应10 min后,三氯生的去除率达90%以上。相对于传统Fenton反应,pH对本非均相催化反应的影响较小,在2～10的pH范围内,仍有较高的催化活性。利用GC-MS分析显示,三氯生降解过程能够产生包括2,4-二氯苯酚在内的多种中间产物。     

Decomposition of low-concentration gas-phase toluene using plasma-driven photocatalyst reactor

Plasma-driven photocatalysis system was prepared and performed. To overcome the treatment difficulty of volatile organic compounds, non-thermal plasma was used as a light source of photocatalysis. The removal of low-concentration toluene was investigated and secondary products were analyzed by gas chromatograph–mass spectroscopy. The plasma-driven photocatalyst reactor using direct current as a light source and titanium dioxide catalyst loaded on activated carbon fiber (TiO₂/ACF) as photocatalyst was studied. It was found that plasma-driven photocatalysis system could significantly increase the removal effect of toluene. The number of secondary products was largely decreased. It means that plasma-driven photocatalysis hybrid system was an effective method for the removal of volatile organic compounds.     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

Batch reactor kinetic studies on the reductive dechlorination of chlorinated ethylenes by tetrakis-(4-sulfonatophenyl)porphyrin cobalt

Tetrakis-(4-sulfonatophenyl)porphyrin cobalt was identified as a highly-active reductive dechlorination catalyst for chlorinated ethylenes. Through batch reactor kinetic studies, degradation of chlorinated ethylenes proceeded in a step-wise fashion with the sequential replacement of Cl by H. For perchloroethylene (PCE) and trichloroethylene (TCE), the dechlorination products were quantified and the C₂ mass was accounted for. Degradation of the chlorinated ethylenes was found to be first-order in substrate. Dechlorination trials with increasing catalyst concentration showed a linearly increasing pseudo first-order rate constant which yielded rate laws for PCE and TCE degradation that are first-order in catalyst. The dechlorination activity of this catalyst was compared to that of another water-soluble cobalt porphyrin under the same reaction conditions and found to be comparable for PCE and TCE.     

光催化-膜分离三相流化床循环反应装置处理酸性红B废水

耦合光催化氧化和有机膜分离技术,设计了一种新型光催化氧化-有机膜分离三相流化床循环反应装置（循环反应装置）;并对循环反应装置光催化降解酸性红B时的影响因素进行了研究。结果表明,减小膜出水通量和降低酸性红B废水浓度均有利于膜出水降解率的提高;循环反应装置中废水降解率随光催化反应器底部曝气量的增加而先增加再降低,膜分离器中废水降解率的波动则随曝气量的增加而总是在增大,其最佳曝气量为1．00m^3／h;光催化反应器中多光源布置有利于循环反应装置的稳定运行;循环反应装置可有效地处理酸性红B废水。     

氧化亚铜光催化降解活性艳红的研究

制备了纳米SiO2-Cu2O复合氧化物,并对其进行表征。研究了SiO2-Cu2O在可见光照射下光催化降解活性艳红X-3B的性能。考察了催化剂组成、活性艳红浓度、催化剂用量、H2O2等对光催化反应的影响,还研究了Cu2O光催化反应动力学。结果表明,用SiO2摩尔含量为2%的SiO2-Cu2O光催化降解活性艳红,反应4 h,活性艳红降解率达到85%,降解反应为一级反应。