Evaluation of an offline method for the analysis of atmospheric reactive gaseous mercury and particulate mercury

Reactive gaseous mercury (RGM) and particulate mercury (PHg) were collected in Milwaukee, WI, between April 2004 and May 2005, and in Riverside, CA, between July 25 and August 7, 2005 using sorbent and filter substrates. The substrates were analyzed for mercury by thermal desorption analysis (TDA) using a purpose-built instrument. Results from this offline-TDA method were compared with measurements using a real-time atmospheric mercury analyzer. RGM measurements made with the offline-TDA agreed well with a commercial real-time method. However, the offline TDA reported PHg concentrations 2.7 times higher than the real-time method, indicating evaporative losses might be occurring from the real-time instrument during sample collection. TDA combined with reactive mercury collection on filter and absorbent substrates was cheap, relatively easy to use, did not introduce biases due to a semicontinuous sample collection strategy, and had a dynamic range appropriate for use in rural and urban locations. The results of this study demonstrate that offline-TDA is a feasible method for collecting reactive mercury concentrations in a large network of filter-based samplers.     

Measurement of Particulate Bound Mercury,Gaseous Elemental Mercury,and Reactive Gaseous Mercury Concentrations by Using an Ambient Air Mercury Collection System

In this investigation, the concentrations of gaseous elemental mercury (GEM), reactive gaseous mercury (RGM) and particulate bound mercury (PBM) in ambient air were measured at the Hung Kuang (traffic) sampling site during September 27 to October 6, 2014. An ambient air mercury collection system (AAMCS) was utilized to measure simultaneously PBM, GEM, and RGM concentrations in ambient air. The results thus obtained demonstrate that the mean concentrations of PBM, GEM, and RGM were 38.57 ± 11.4 (pg/m³), 17.67 ± 5.56 (ng/m³) and 10.78 ± 2.8 (pg/m³), respectively, at this traffic-sampling site. The mean GEM/PBM and GEM/RGM concentration ratios were 458 and 1639, respectively. The results obtained herein demonstrate that AAMCS can be utilized to collect three phases of mercury simultaneously. The mean PBM, GEM, and RGM concentrations herein were compared with others found in Asia, America, Europe and Antarctica. The mean PBM, GEM, and RGM concentrations were found to be lowest in Asia and Antarctica. The mean PBM concentration in Europe was approximately eight times that in this investigation. The mean GEM and RGM concentrations in this study were 1.21 and 170 times those found in the United States.     

Temporal distribution and potential sources of atmospheric mercury measured at a high-elevation background station in Taiwan

Measurements of gaseous elemental mercury (GEM), reactive gaseous mercury (RGM), and particulate mercury (PHg) have been conducted at Lulin Atmospheric Background Station (LABS) in Taiwan since April 2006. This was the first long-term free tropospheric atmospheric Hg monitoring program in the downwind region of East Asia, which is a major Hg emission source region. Between April 13, 2006 and December 31, 2007, the mean concentrations of GEM, RGM, and PHg were 1.73 ng m^?3, 12.1 pg m^?3, and 2.3 pg m^?3, respectively. A diurnal pattern was observed for GEM with afternoon peaks and nighttime lows, whereas the diurnal pattern of RGM was opposite to that of GEM. Spikes of RGM were frequently observed between midnight and early morning with concurrent decreases in GEM and relative humidity and increases in O₃, suggesting the oxidation of GEM and formation of RGM in free troposphere (FT). Upslope movement of boundary layer (BL) air in daytime and subsidence of FT air at night resulted in these diurnal patterns. Considering only the nighttime data, which were more representative of FT air, the composite monthly mean GEM concentrations ranged between 1.06 and 2.06 ng m^?3. Seasonal variation in nighttime GEM was evident, with lower concentrations usually occurring in summer when clean marine air masses prevailed. Between fall and spring, air masses passed the East Asian continent prior to reaching LABS, contributing to the elevated GEM concentrations. Analysis of GEM/CO correlation tends to support the argument. Good GEM/CO correlations were observed in fall, winter, and spring, suggesting influence of anthropogenic emission sources. Our results demonstrate the significance of East Asian Hg emissions, including both anthropogenic and biomass burning emissions, and their long-range transport in the FT. Because of the pronounced seasonal monsoon activity and the seasonal variation in regional wind field, export of the Asian Hg emissions to Taiwan occurs mainly during fall, winter, and spring.     

Mercury chemistry in the MBL: Mediterranean case and sensitivity studies using the AMCOTS (Atmospheric Mercury Chemistry over the Sea) model

The atmospheric oxidation of mercury in the Mediterranean marine boundary layer (MBL) has been studied using the Atmospheric Mercury Chemistry over the Sea (AMCOTS) model. The model results have been compared to measured data obtained during an oceanographic research campaign in 2000, with more success than previous modelling attempts. In light of the often high concentrations of ozone present in the Mediterranean boundary layer, seasonal case studies using typical meteorological conditions and average ozone concentrations have been performed to identify the main oxidants of elemental mercury. The sensitivity of the modelled reactive gaseous mercury (RGM) concentrations to the Hg+O₃ rate constant has been assessed using the two most recent rate determinations. The results using the higher of the two literature values gives results inconsistent with measured values of RGM when the reaction between Hg and O₃ is assumed to give a gas phase product. This does not necessarily indicate that the rate constant is incorrect but possibly that other rate constants in the model are overestimated or indeed that there may be reduction reactions occurring in the atmosphere which have yet to be identified. Alternatively, when the reaction product of Hg and O₃ is assumed to be a solid and therefore not contribute to RGM the modelled and measured results are comparable. The deposition rates calculated by the model when compared with calculated and measured sea surface emission fluxes available in the literature indicate that dry deposition flux of RGM is comparable to the sea surface emission flux. The calculated lifetime of Hg⁰ in the Mediterranean MBL is between one and two weeks.     

Particulate mercury emissions in regional wildfire plumes observed at the Mount Bachelor Observatory

Atmospheric mercury is composed primarily of Hg⁰ (>95%), but Hg⁺² and particle bound mercury are also found in some environments. The three forms of mercury were measured at the Mount Bachelor Observatory beginning in 2005. Using data gathered from 2005 to 2007, 15 periods were identified during which PHg was above the instrument detection limit of 3 pg m^?3 for nine or more consecutive hours. Peak PHg concentrations ranged from 6.0 to 44.3 pg m^?3. During these events, PHg is strongly correlated with CO and sub-micron aerosol scatter coefficient (typically R² > 0.6). Our data suggest that the 15 PHg events were likely due to regional wildfires in California and Oregon. Wildfires were identified as the primary PHg source using a combination of air-mass back-trajectories, MODIS satellite data, and chemical and physical tracers of combustion. Slopes of the PHg/σ_sp and PHg/CO relationships ranged from 0.20 to 1.57 pg (Mm^?1)^?1 and 0.11 to 0.61 pg m^?3 ppb^?1, respectively. The range of slopes may indicate different types of burning (e.g. flaming vs. smoldering), differing amounts of chemical processing, different fuel sources, or different physical parameters such as the plume injection height. The slopes provide constraints for the relationship between PHg, CO, and aerosol scatter from wildfires. Asian long-range transport was not a source of PHg but we cannot rule out the possibility of local U.S. industrial sources of PHg for some of the events. Assuming our observations are representative of global fire emissions, we estimate that PHg represents 15% of the total mercury released from wildfires and is a source of PHg comparable to anthropogenic sources.     

Measurements of atmospheric mercury species during an international study of mercury depletion events at Ny-Ålesund,Svalbard, spring 2003. How reproducible are our present methods?

Six groups participated in an international study of springtime atmospheric mercury depletion events (AMDEs) at Ny-Ålesund in the Norwegian Arctic during April and May 2003 with the aim to compare analytical methods for measurements of atmospheric mercury species and study the physical and chemical processes leading to AMDEs. Five groups participated in the method comparison that was conducted at three different locations within Ny-Ålesund. Various automated and manual instrumentation were used to sample, measure and compare gaseous elemental mercury (GEM), reactive gaseous mercury (RGM) and mercury associated with particles (Hg-P). The concentration of GEM was reproducible during background conditions. For the first time using ambient air, the statistics associated with round robin test procedures were applied. This was found to be an appropriate tool to investigate the reproducibility of GEM measurements in ambient air. The precision for each group measuring GEM concentrations was found to be consistently good (within 5%). Five AMDEs were recorded during the study. Using four different methods, including single and replicate samples, all groups recorded higher values of RGM and Hg-P during AMDEs. The results show that measuring comparable atmospheric mercury species at both the same and different locations (within the Ny-Ålesund area) is difficult. Not only do site location and site characteristics create challenges when trying to intercompare results but there are difficulties, as well, in obtaining comparable results with similar sampling and analysis methods. Nevertheless, with our current procedures for atmospheric mercury identification we can differentiate with certainty between “high” and “low” concentration values of RGM and Hg-P.     

Temporal variability of mercury speciation in urban air

Semi-continuous measurements of ambient mercury (Hg) species were performed in Detroit, MI, USA for the calendar year 2003. The mean (±standard deviation) concentrations for gaseous elemental mercury (GEM), particulate mercury (HgP), and reactive gaseous mercury (RGM) were 2.2±1.3 ng m⁻³, 20.8±30.0, and 17.7±28.9 pg m⁻³, respectively. A clear seasonality in Hg speciation was observed with GEM and RGM concentrations significantly (p<0.001) greater in warm seasons, while HgP concentrations were greater in cold seasons. The three measured Hg species also exhibited clear diurnal trends which were particularly evident during the summer months. Higher RGM concentrations were observed during the day than at night. Hourly HgP and GEM concentrations exhibited a similar diurnal pattern with both being inversely correlated with RGM. Multivariate analysis coupled with conditional probability function analysis revealed the conditions associated with high Hg concentration episodes, and identified the inter-correlations between speciated Hg concentrations, three common urban air pollutants (sulfur dioxide, ozone, and nitric oxides), and meteorological parameters. This analysis suggests that both local and regional sources were major factors contributing to the observed temporal variations in Hg speciation. Boundary layer dynamics and the seasonal meteorological conditions, including temperature and moisture content, were also important factors affecting Hg variability.     

Estimating contribution of precipitation scavenging of atmospheric particulate mercury to mercury wet deposition in Japan

Mercury wet deposition is dependent on both the scavenging of divalent reactive gaseous mercury (RGM) and atmospheric particulate mercury (Hg(p)) by precipitation. Estimating the contribution of precipitation scavenging of RGM and Hg(p) is important for better understanding the causes of the regional and seasonal variations in mercury wet deposition. In this study, the contribution of Hg(p) scavenging was estimated on the basis of the scavenging ratios of other trace elements (i.e., Cd, Cu, Mn, Ni, Pb and V) existing entirely in particulate form. Their wet deposition fluxes and concentrations in air, which were measured concurrently from April 2004 to March 2005 at 10 sites in Japan, were used in this estimation. The monthly wet deposition flux of mercury at each site correlated with the amount of monthly precipitation, whereas the Hg(p) concentrations in air tended to decrease during summer. There was a significant correlation (P<0.001) among the calculated monthly average scavenging ratios of trace elements, and the values in each month at each site were similar. Therefore, it is assumed the monthly scavenging ratio of Hg(p) is equivalent to the mean value of other trace elements. Using this scavenging ratio (W), the wet deposition flux (F) due to Hg(p) scavenging in each month was calculated by F=WKP, where K and P are the Hg(p) concentration and amount of precipitation, respectively. Relatively large fluxes due to Hg(p) scavenging were observed at a highly industrial site and at sites on the Japan Sea coast, which are strongly affected by the local sources and the long-range transport from the Asian continent, respectively. However, on average, at the 10 sites, the contribution of Hg(p) scavenging to the annual mercury deposition flux was 26%, suggesting that mercury wet deposition in Japan is dominated by RGM scavenging. This RGM should originate mainly from the in situ oxidation of Hg⁰ in the atmosphere.     

Investigation of a Mercury Speciation Technique for Flue Gas Desulfurization Materials

Abstract

Most of the synthetic gypsum generated from wet flue gas desulfurization (FGD) scrubbers is currently being used for wallboard production. Because oxidized mercury is readily captured by the wet FGD scrubber, and coal-fired power plants equipped with wet scrubbers desire to benefit from the partial mercury control that these systems provide, some mercury is likely to be bound in with the FGD gypsum and wallboard. In this study, the feasibility of identifying mercury species in the FGD gypsum and wallboard samples was investigated using a large sample size thermal desorption method. Potential candidates of pure mercury standards including mercuric chloride (HgCl₂), mercurous chloride (Hg₂Cl₂), mercury oxide (HgO), mercury sulfide (HgS), and mercuric sulfate (HgSO₄) were analyzed to compare their results with those obtained from FGD gypsum and dry wallboard samples. Although any of the thermal evolutionary curves obtained from these pure mercury standards did not exactly match with those of the FGD gypsum and wallboard samples, it was identified that Hg₂Cl₂ and HgCl₂ could be candidates. An additional chlorine analysis from the gypsum and wallboard samples indicated that the chlorine concentrations were approximately 2 orders of magnitude higher than the mercury concentrations, suggesting possible chlorine association with mercury.     

Atmospheric mercury distribution in Northern Europe and in the Mediterranean region

Mercury species in air have been measured at five sites in Northwest Europe and at five coastal sites in the Mediterranean region during measurements at four seasons. Observed concentrations of total gaseous mercury (TGM), total particulate mercury (TPM) and reactive gaseous mercury (RGM) were generally slightly higher in the Mediterranean region than in Northwest Europe. Incoming clean Atlantic air seems to be enriched in TGM in comparison to air in Scandinavia. Trajectory analysis of events where high concentrations of TPM simultaneously were observed at sites in North Europe indicate source areas in Central Europe and provide evidence of transport of mercury on particles on a regional scale.     

Atmospheric mercury concentrations and speciation measured from 2004 to 2007 in Reno, Nevada, USA

Atmospheric elemental, reactive and particulate mercury (Hg) concentrations were measured north of downtown Reno, Nevada, USA from November 2004 to November 2007. Three-year mean and median concentrations for gaseous elemental Hg (Hg⁰) were 1.6 and 1.5 ng m⁻³ (respectively), similar to global mean Hg⁰ concentrations. The three-year mean reactive gaseous Hg (RGM) concentration (26 pg m⁻³) was higher than values reported for rural sites across the western United States. Well defined seasonal and daily patterns in Hg⁰ and RGM concentrations were observed, with the highest Hg⁰ concentrations measured in winter and early morning, and RGM concentrations being greatest in the summer and mid-afternoon. Elevated Hg⁰ concentrations in winter were associated with periods of cold, stagnant air; while a regularly observed early morning increase in concentration was due to local source and surface emissions. The observed afternoon increase and high summer values of RGM can be explained by in situ oxidation of gaseous Hg⁰ or mixing of RGM derived from the free troposphere to the surface. Because both of these processes are correlated with the same environmental conditions it is difficult to assess their overall contribution to the observed trends.     

A review of current knowledge concerning dry deposition of atmospheric mercury

The status of the current knowledge concerning the dry deposition of atmospheric mercury, including elemental gaseous mercury (Hg⁰), reactive gaseous mercury (RGM), and particulate mercury (Hg_p), is reviewed. The air–surface exchange of Hg⁰ is commonly bi-directional, with daytime emission and nighttime deposition over non-vegetated surfaces and vegetated surfaces with small leaf area indices under low ambient Hg⁰ conditions. However, daytime deposition has also been observed, especially when the ambient Hg⁰ is high. Typical dry deposition velocities (V_d) for Hg⁰ are in the range of 0.1–0.4 cm s^?1 over vegetated surfaces and wetlands, but substantially smaller over non-vegetated surfaces and soils below canopies. Meteorological, biological, and soil conditions, as well as the ambient Hg⁰ concentrations all play important roles in the diurnal and seasonal variations of Hg⁰ air–surface exchange processes. Measurements of RGM deposition are limited and are known to have large uncertainties. Nevertheless, all of the measurements suggest that RGM can deposit very quickly onto any type of surface, with its V_d ranging from 0.5 to 6 cm s^?1. The very limited data for Hg_p suggest that its V_d values are in the range of 0.02–2 cm s^?1.A resistance approach is commonly used in mercury transport models to estimate V_d for RGM and Hg_p; however, there is a wide range of complexities in the dry deposition scheme of Hg⁰. Although resistance-approach based dry deposition schemes seem to be able to produce the typical V_d values for RGM and Hg⁰ over different surface types, more sophisticated air–surface exchange models have been developed to handle the bi-directional exchange processes. Both existing and newly developed dry deposition schemes need further evaluation using field measurements and intercomparisons within different modelling frameworks.     

The effect of temperature on the gas–particle partitioning of reactive mercury in atmospheric aerosols

Measurements of gas–particle-partitioning coefficients for reactive mercury in dry urban and laboratory aerosol were found to strongly depend on ambient temperature. Samples of atmospheric and laboratory aerosols (defined as both the gas and particle phases) were collected using filter and absorbent methods and analyzed for reactive mercury using thermal desorption combined with cold vapor atomic fluorescence spectroscopy. Synthetic ambient aerosols were generated in the laboratory from ammonium sulfate and adipic acid mixed with mercuric chloride in a purpose-built aerosol reactor. The aerosol reactor was operated in a temperature-controlled laboratory. Linear relationships between the logarithm of inverse gas–particle partitioning and inverse temperature were observed and parameterized for use in the atmospheric modeling of reactive mercury. Reactive mercury was observed to partition from the particle to the gas phase as ambient temperature increased. Good agreement between measurements made using urban and laboratory aerosols was seen after gas–particle-partitioning coefficients were normalized for surface area instead of mass. Thermodynamic analyses of the urban and laboratory gas–particle-partitioning measurements revealed that the strength of interaction between reactive mercury and particle surfaces was suggestive of chemisorption. Gas–particle-partitioning coefficients made with the Tekran ambient mercury analyzer (AMA) also showed a dependence on temperature. However, the Tekran AMA partitioning coefficients did not agree well with partitioning coefficients measured using the filter-based methods. The disagreement is consistent with the 50 °C operational temperature of the Tekran AMA.     

Sources and deposition of reactive gaseous mercury in the marine atmosphere

Observations of reactive gaseous mercury (RGM) in marine air show a consistent diurnal cycle with minimum at night, rapid increase at sunrise, maximum at midday, and rapid decline in afternoon. We use a box model for the marine boundary layer (MBL) to interpret these observations in terms of RGM sources and sinks. The morning rise and midday maximum are consistent with oxidation of elemental mercury (Hg⁰) by Br atoms, requiring <2 ppt BrO in most conditions. Oxidation of Hg⁰ by Br accounts for 35–60% of the RGM source in our model MBL, with most of the remainder contributed by oxidation of Hg⁰ by ozone (5–20%) and entrainment of RGM-rich air from the free troposphere (25–40%). Oxidation of Hg⁰ by Cl is minor (3–7%), and oxidation by OH cannot reproduce the observed RGM diurnal cycle, suggesting that it is unimportant. Fitting the RGM observations could be achieved in the model without oxidation of Hg⁰ by ozone (leaving Br as the only significant oxidant) by increasing the entrainment flux from the free troposphere. The large relative diurnal amplitude of RGM concentrations implies rapid loss with a lifetime of only a few hours. We show that this can be quantitatively explained by rapid, mass-transfer-limited uptake of RGM into sea-salt aerosols as HgCl₃^? and HgCl₄^2?. Our results suggest that 80–95% of Hg^II in the MBL should be present in sea-salt aerosol rather than gas-phase, and that deposition of sea-salt aerosols is the major pathway delivering Hg^II to the ocean.     

Intercomparison of methods for sampling and analysis of atmospheric mercury species

An intercomparison for sampling and analysis of atmospheric mercury species was held in Tuscany, June 1998. Methods for sampling and analysis of total gaseous mercury (TGM), reactive gaseous mercury (RGM) and total particulate mercury (TPM) were used in parallel sampling over a period of 4 days. The results show that the different methods employed for TGM compared well whereas RGM and TPM showed a somewhat higher variability. Measurement results of RGM and TPM improved over the time period indicating that activities at the sampling site during set-up and initial sampling affected the results. Especially the TPM measurement results were affected. Additional parallel sampling was performed for two of the TPM methods under more controlled conditions which yielded more comparable results.     

An Evaluation of the Tapered Element Oscillating Microbalance Method for Measuring Diesel Particulate Emissions

Abstract

We determined the usefulness of tapered element oscillating microbalances (TEOMs) for researchers and engineers involved with measuring diesel particulate mass. Two different test facilities were used for generating diesel particulates and comparing the TEOM to the commonly used U.S. Environmental Protection Agency (EPA) manual filter method. The EPA method is very labor-intensive and requires long periods of time to complete. The TEOM is an attractive approach because it has the potential to reduce the amount of time and labor required in diesel testing, as well as to provide real-time particulate-mass data that are not obtainable with the EPA method. It was found that the TEOM was a precise and easy-to-operate instrument that could measure the mass concentration (MC) of diesel particulate emissions in real time. Although the TEOM diesel particulate MC measurements were highly correlated with the manual filter measurements, the two techniques were not equivalent because the TEOM consistently reported MC results that were 20–25% lower than those obtained using the manual filter technique. In conclusion, the TEOM can be used to increase test-cell throughput and to measure transient values of diesel par-ticulate emissions at sites performing diesel-engine testing. However, unless EPA is able to certify the TEOM as an equivalent method, it cannot replace the manual filter method for diesel certification work.     

Urban–rural differences in atmospheric mercury speciation

Measurements of gaseous elemental mercury (GEM), particulate mercury (Hg_p), and reactive gaseous mercury (RGM) were concurrently recorded at an urban site in Detroit and a rural site in Dexter, both in Michigan for the calendar year 2004. Their average concentrations (±standard deviation) for the urban area were 2.5 ± 1.4 ng m^?3, 18.1 ± 61.0 pg m^?3, and 15.5 ± 54.9 pg m^?3, respectively, while their rural counterparts were 1.6 ± 0.6 ng m^?3, 6.1 ± 5.5 pg m^?3, and 3.8 ± 6.6 pg m^?3, respectively. The medians of urban-to-rural ratios of Hg concentrations indicate approximately 1-fold, 2-fold, and 3-fold gradients between Detroit and Dexter for GEM, Hg_p, and RGM, respectively. The urban–rural differences in Hg also varied considerably on different temporal scales and with wind flow patterns, which was most evident in RGM. Our results show that while Hg at both sites was impacted by regional sources, meteorological conditions, and photochemical transformations, the extent of variations in the observed urban-to-rural gradients, particularly in RGM, cannot be fully accounted for by these processes. Both analyses of the annual data and case studies indicate that the more variable and episodic nature of Hg, particularly RGM, seen in Detroit compared with Dexter, was the result of direct impact from local anthropogenic sources.     

The influence of ozone on atmospheric emissions of gaseous elemental mercury and reactive gaseous mercury from substrates

Experiments were performed to investigate the effect of ozone (O₃) on mercury (Hg) emission from a variety of Hg-bearing substrates. Substrates with Hg(II) as the dominant Hg phase exhibited a 1.7 to 51-fold increase in elemental Hg (Hg^o) flux and a 1.3 to 8.6-fold increase in reactive gaseous mercury (RGM) flux in the presence of O₃-enriched clean (50 ppb O₃; 8 substrates) and ambient air (up to ∼70 ppb O₃; 6 substrates), relative to clean air (oxidant and Hg free air). In contrast, Hg^o fluxes from two artificially Hg^o-amended substrates decreased by more than 75% during exposure to O₃-enriched clean air relative to clean air. Reactive gaseous mercury emissions from Hg^o-amended substrates increased immediately after exposure to O₃ but then decreased rapidly. These experimental results demonstrate that O₃ is very important in controlling Hg emissions from substrates. The chemical mechanisms that produced these trends are not known but potentially involve heterogenous reactions between O₃, the substrate, and Hg. Our experiments suggest they are not homogenous gas-phase reactions. Comparison of the influence of O₃ versus light on increasing Hg^o emissions from dry Hg(II)-bearing substrates demonstrated that they have a similar amount of influence although O₃ appeared to be slightly more dominant. Experiments using water-saturated substrates showed that the presence of high-substrate moisture content minimizes reactions between atmospheric O₃ and substrate-bound Hg. Using conservative calculations developed in this paper, we conclude that because O₃ concentrations have roughly doubled in the last 100 years, this could have increased Hg^o emissions from terrestrial substrates by 65–72%.     

Evidence for short-range transport of atmospheric mercury to a rural,inland site

Atmospheric mercury (Hg) species, including gaseous elemental mercury (GEM), reactive gaseous mercury (RGM) and particulate-bound mercury (Hg_p), were monitored near three sites, including a cement plant (monitored in 2007 and 2008), an urban site and a rural site (both monitored in 2005 and 2008). Although the cement plant was a significant source of Hg emissions (for 2008, GEM: 2.20 ± 1.39 ng m^?3, RGM: 25.2 ± 52.8 pg m^?3, Hg_p 80.8 ± 283 pg m^?3), average GEM levels and daytime average dry depositional RGM flux were highest at the rural site, when all three sites were monitored sequentially in 2008 (rural site, GEM: 2.37 ± 1.26 ng m^?3, daytime RGM flux: 29 ± 40 ng m^?2 day^?1). Photochemical conversion of GEM was not the primary RGM source, as highest net RGM gains (75.9 pg m^?3, 99.0 pg m^?3, 149 m^?3) occurred within 3.0–5.3 h, while the theoretical time required was 14–23 h. Instead, simultaneous peaks in RGM, Hg_p, ozone (O₃), nitrogen oxides, and sulfur dioxide in the late afternoon suggested short-range transport of RGM from the urban center to the rural site. The rural site was located more inland, where the average water vapor mixing ratio was lower compared to the other two sites (in 2008, rural: 5.6 ± 1.4 g kg^?1, urban: 9.0 ± 1.1 g kg^?1, cement plant: 8.3 ± 2.2 g kg^?1). Together, these findings suggested short-range transport of O₃ from an urban area contributed to higher RGM deposition at the rural site, while drier conditions helped sustain elevated RGM levels. Results suggested less urbanized environments may be equally or perhaps more impacted by industrial atmospheric Hg emissions, compared to the urban areas from where Hg emissions originated.     

Mercury in feathers of Squacco Heron (Ardeola ralloides) chicks in relation to age, hatching order, growth, and sampling dates

We studied the relationships between mercury content of Squacco Heron (Ardeola ralloides) chick body-feathers and nestling age, hatching order (seniors-juniors) and growth parameters, and the date of feather sampling in the Axios Delta, northern Greece, in 1993 (n = 75 chicks) and 1994 (n = 80). Mercury levels were not significantly correlated with chick age in either year of the study. Most of the variability in mercury (90%) was found among broods, attributable to differential prey selection and/or foraging habitat and patch utilization by parents. Within broods, juniors had significantly higher mercury loads than seniors in 1993, but there was no significant difference between the two in 1994. Correlations of nestling weight and linear measurements corrected for chick age and mercury concentrations were never significant and explained small amounts of variability in chick growth. However, linear measurements corrected for age were significantly higher among seniors in 1993, when those nestlings had lower mercury loads than their siblings. Mercury levels were unaffected by the date of feather collection in 1993, but exhibited a significant increase over time in 1994. This can be attributed to a shift towards more highly contaminated habitats and prey types by foraging parents, resulting from seasonal changes in water level and vegetation cover in important foraging habitats. Feather collection from Squacco Heron nestlings late in the breeding season seems to be an appropriate method for biomonitoring mercury pollution in the Axios Delta.