Source Apportionment of Ambient Total Suspended Particulates and Coarse Particulate Matter in Urban Areas of Jiaozuo,China

Abstract

Approximately 750 total suspended particulates (TSPs) and coarse particulate matter (PM₁₀) filter samples from six urban sites and a background site and >210 source samples were collected in Jiaozuo City during January 2002 to April 2003. They were analyzed for mass and abundances of 25 chemical components. Seven contributive sources were identified, and their contributions to ambient TSP/PM₁₀ levels at the seven sites in three seasons (spring, summer, and winter days) and a “whole” year were estimated by a chemical mass balance (CMB) receptor model. The spatial TSP average was high in spring and winter days at a level of approximately 530 ～g/m³ and low in summer days at 456 ～g/m³; however, the spatial PM₁₀ average exhibited little variation at a level of approximately 325 ～g/m³, and PM_10-to-TSP ratios ranged from 0.58 to 0.81, which suggested heavy particulate matter pollution existing in the urban areas. Apportionment results indicated that geological material was the largest contributor to ambient TSP/PM₁₀ concentrations, followed by dust emissions from construction activities, coal combustion, secondary aerosols, vehicle movement, and other industrial sources. In addition, paved road dust and re-entrained dust were also apportioned to the seven source types and found soil, coal combustion, and construction dust to be the major contributors.     

Monitoring and Source Apportionment of Particulate Matter near a Large Phosphorus Production Facility

ABSTRACT

A source apportionment study was conducted to identify sources within a large elemental phosphorus plant that contribute to exceedances of the National Ambient Air Quality Standards (NAAQS) for 24-hr PM₁₀. Ambient data were collected at three monitoring sites from October 1996 through July 1999, and included the following: 24-hr PM₁₀ mass, 24-hr PM_2.5 and PM_10–2.5 mass and chemistry, continuous PM₁₀and PM_2.5 mass, continuous meteorological data, and wind-direction-resolved PM_2.5 and PM₁₀ mass and chemistry. Ambient-based receptor modeling and wind-directional analysis were employed to help identify major sources or source locations and source contributions. Fine-fraction phosphate was the dominant species observed during PM₁₀ exceedances, though in general, re-suspended coarse dusts from raw and processed materials at the plant were also needed to create an exceedance. Major sources that were identified included the calciners, the CO flares, process-related dust, and electric-arc furnace operations.     

Source Apportionment of Fine Particulate Matter in the Southeastern United States

Abstract

Particulate matter (PM) less than 2.5 μm in size (PM_2.5)source apportionment by chemical mass balance receptor modeling was performed to enhance regional characterization of source impacts in the southeastern United States. Secondary particles, such as NH₄HSO₄, (NH₄)₂SO₄,NH₄NO₃, and secondary organic carbon (OC) (SOC), formed by atmospheric photochemical reactions, contribute the majority (<50%) of ambient PM_2.5 with strong seasonality. Source apportionment results indicate that motor vehicle and biomass burning are the two main primary sources in the southeast, showing relatively more motor vehicle source impacts rather than biomass burning source impacts in populated urban areas and vice versa in less urbanized areas. Spatial distributions of primary source impacts show that each primary source has distinctively different spatial source impacts. Results also find impacts from shipping activities along the coast. Spatiotemporal correlations indicate that secondary particles are more regionally distributed, as are biomass burning and dust, whereas impacts of other primary sources are more local.     

Source Apportionment of Particulate Matter (PM10) and Indoor Dust in a University Building

A study on source apportionment of indoor dust and particulate matter (PM₁₀) composition was conducted in a university building by using chemometrics. The objective of this study was to investigate the potential sources of selected heavy metals and ionic species in PM₁₀ and indoor dust. PM₁₀ samples were collected using a low-volume sampler (LVS) and indoor dust was collected using a soft brush. Inductively coupled plasma spectrometry (ICP-MS) was used to determine the concentration of heavy metals, while the concentration of cations and anions was determined by atomic absorption spectrometer (AAS) and ion chromatography (IC), respectively. The concentration of PM₁₀ recorded in the building throughout the sampling period ranged from 20 ± 10 μgm^?3 to 80 ± 33 μgm^?3. The composition of heavy metals in PM₁₀ and indoor dust were dominated by zinc (Zn), followed by lead (Pb), copper (Cu), and cadmium (Cd). Principle component analysis (PCA) and multiple linear regression (MLR) showed that the main sources of pollutants in PM₁₀ came from indoor renovations (73.83%), vehicle emissions (16.38%), earth crust sources (9.68%), and other outdoor sources (0.11%). For indoor dust, the pollutant source was mainly earth crust. This study suggests that chemometrics can be used for forensic investigation to determine the possible sources of indoor contaminants within a public building.     

Sensitivity of Source Apportionment of Urban Particulate Matter to Uncertainty in Motor Vehicle Emissions Profiles

Abstract

A sensitivity analysis was conducted to characterize sources of uncertainty in results of a molecular marker source apportionment model of ambient particulate matter using mobile source emissions profiles obtained as part of the Gasoline/Diesel PM Split Study. A chemical mass balance (CMB) model was used to determine source contributions to samples of fine particulate matter (PM_2.5) collected over 3 weeks at two sites in the Los Angeles area in July 2001. The ambient samples were composited for organic compound analysis by the day of the week to investigate weekly trends in source contributions. The sensitivity analysis specifically examined the impact of the uncertainty in mobile source emissions profiles on the CMB model results. The key parameter impacting model sensitivity was the source profile for gasoline smoker vehicles. High-emitting gasoline smoker vehicles with visible plumes were seen to be a significant source of PM in the area, but use of different measured profiles for smoker vehicles in the model gave very different results for apportionment of gasoline, diesel, and smoker vehicle tailpipe emissions. In addition, the contributions of gasoline and diesel emissions to total ambient PM varied as a function of the site and the day of the week.     

Effects of Wind Direction on Coarse and Fine Particulate Matter Concentrations in Southeast Kansas

Abstract

Field data for coarse particulate matter ([PM] PM₁₀) and fine particulate matter (PM_2.5) were collected at selected sites in Southeast Kansas from March 1999 to October 2000, using portable MiniVol particulate samplers. The purpose was to assess the influence on air quality of four industrial facilities that burn hazardous waste in the area located in the communities of Chanute, Independence, Fredonia, and Coffeyville. Both spatial and temporal variation were observed in the data. Variation because of sampling site was found to be statistically significant for PM₁₀ but not for PM_2.5. PM₁₀ concentrations were typically slightly higher at sites located within the four study communities than at background sites. Sampling sites were located north and south of the four targeted sources to provide upwind and downwind monitoring pairs. No statistically significant differences were found between upwind and downwind samples for either PM₁₀ or PM_2.5, indicating that the targeted sources did not contribute significantly to PM concentrations. Wind direction can frequently contribute to temporal variation in air pollutant concentrations and was investigated in this study. Sampling days were divided into four classifications: predominantly south winds, predominantly north winds, calm/variable winds, and winds from other directions. The effect of wind direction was found to be statistically significant for both PM₁₀ and PM_2.5. For both size ranges, PM concentrations were typically highest on days with predominantly south winds; days with calm/variable winds generally produced higher concentrations than did those with predominantly north winds or those with winds from “other” directions. The significant effect of wind direction suggests that regional sources may exert a large influence on PM concentrations in the area.     

Receptor Oriented Methods of Air Particulate Source Apportionment

Receptor models have evolved rapidly over the past 13 years but have just recently been recognized as a distinct discipline. The general category of receptor models includes both microscopic and chemical methods of apportioning source contributions to ambient air particulates. The number and variations of these methods have grown rapidly over the past few years and include such methods as automated scanning electron microscopy, chemical mass balance and multivariate procedures. These methods as well as hybrid procedures such as target transformation factor analysis, are reviewed and their boundary conditions, strengths, and weaknesses discussed.     

Apportionment of Ambient Primary and Secondary Fine Particulate Matter during a 2001 Summer Intensive Study at the CMU Supersite and NETL Pittsburgh Site

Abstract

Gaseous and particulate pollutant concentrations associated with five samples per day collected during a July 2001 summer intensive study at the Pittsburgh Carnegie Mellon University (CMU) Supersite were used to apportion fine particulate matter (PM_2.5) into primary and secondary contributions using PMF2. Input to the PMF2 analysis included the concentrations of PM_2.5 nonvolatile and semivolatile organic material, elemental carbon (EC), ammonium sulfate, trace element components, gas-phase organic material, and NO_x, NO₂, and O₃ concentrations. A total of 10 factors were identified. These factors are associated with emissions from various sources and facilities including crustal material, gasoline combustion, diesel combustion, and three nearby sources high in trace metals. In addition, four secondary sources were identified, three of which were associated with secondary products of local emissions and were dominated by organic material and one of which was dominated by secondary ammonium sulfate transported to the CMU site from the west and southwest. The three largest contributors to PM_2.5 were sec ondary transported material (dominated by ammonium sulfate) from the west and southwest (49%), secondary material formed during midday photochemical processes (24%), and gasoline combustion emissions (11%). The other seven sources accounted for the remaining 16% of the PM_2.5. Results obtained at the CMU site were comparable to results previously reported at the National Energy Technology Laboratory (NETL), located approximately 18 km south of downtown Pittsburgh. The major contributor at both sites was material transported from the west and southwest. Some difference in nearby sources could be attributed to meteorology as evaluated by HYSPLIT model back-trajectory calculations. These findings are consistent with the majority of the secondary ammonium sulfate in the Pittsburgh area being the result of contributions from distant transport, and thus decoupled from local activity involving organic pollutants in the metropolitan area. In contrast, the major local secondary sources were dominated by organic material.     

Chromium Analysis at a Ferrochrome Smelter,a Chemical Plant and a Refractory Brick Plant

Techniques were developed to sample and analyze the Cr content of participate samples with emphasis on determining the concentration of the carcinogen Cr⁺⁶. Cr⁺⁶ is extracted to alkaline solution and analyzed colorimetrically. Residual particles are extracted with acid solution to remove soluble Cr⁺³, which is determined by atomic absorption spectrometry. This methodology was tested on samples from three diverse types of sources: a ferrochrome smelter, a chemical plant, and a refractory brick plant. Identical quadruplicate samples were collected to determine accuracy and precision of the collection and analysis procedures, and extraction of Cr⁺⁶ and Cr⁺³. A statistical analysis revealed that the precision of Cr⁺⁶ analysis is comparable to that of the particulate mass determination. The stability of Cr⁺⁶ In particulate form and in solution was determined. Size resolved particulate samples were collected to determine the particle size versus the Cr⁺⁶ content. At the ferrochrome smelter and the chemical plant the majority of the Cr⁺⁶ was contained in the respirable particles. The accuracy and completeness of the chemical methods employed were verified by neutron activation analysis, x-ray photoelectron spectroscopy, and scanning electron microscopyenergy dispersive x-ray analysis.     

Characterization of Particulate Matter in California

ABSTRACT

The size, composition, and concentration of particulate matter (PM) vary with location and time. Several monitoring/sampling programs are operated in California to characterize PM less than 2.5 and 10 µm in aerodynamic diameter (PM_2.5 and PM₁₀). This paper presents a broad summary of the spatial and temporal variations observed in ambient PM_2.5 and PM₁₀ concentrations in California. Many areas that have high PM₁₀ concentrations also have relatively high PM_2.5 concentrations, and data indicate that a significant portion of the PM₁₀ air quality problem is caused by PM_2.5. To develop effective plans for attaining the ambient PM standards, improved understanding of these unique problems is needed. Since 1989, pollution control efforts—whether specifically targeted for particulate matter or indirectly via controls on gaseous emissions—have caused annual average PM_2.5 and PM₁₀ concentrations to decline at most sites in California.     

A Pilot Indoor-Outdoor Study of Organic Particulate Matter and Particulate Mutagenicity

Abstract

Many large metropolitan areas experience elevated concentrations of ground-level ozone pollution during the summertime “smog season”. Local environmental or health agencies often need to make daily air pollution forecasts for public advisories and for input into decisions regarding abatement measures and air quality management. Such forecasts are usually based on statistical relationships between weather conditions and ambient air pollution concentrations. Multivariate linear regression models have been widely used for this purpose, and well-specified regressions can provide reasonable results. However, pollution-weather relationships are typically complex and nonlinear—especially for ozone—properties that might be better captured by neural networks. This study investigates the potential for using neural networks to forecast ozone pollution, as compared to traditional regression models. Multiple regression models and neural networks are examined for a range of cities under different climate and ozone regimes, enabling a comparative study of the two approaches. Model comparison statistics indicate that neural network techniques are somewhat (but not dramatically) better than regression models for daily ozone prediction, and that all types of models are sensitive to different weather-ozone regimes and the role of persistence in aiding predictions.     

Effect of the Fine Fraction of Particulate Matter versus the Coarse Mass and Other Pollutants on Daily Mortality in Santiago,Chile

ABSTRACT

Daily counts of non-accidental deaths in Santiago, Chile, from 1988 to 1996 were regressed on six air pollutants— fine particles (PM_2.5), coarse particles (PM_10–2.5), CO, SO₂, NO₂, and O₃. Controlling for seasonal and meteorological conditions was done using three different models— a generalized linear model, a generalized additive model, and a generalized additive model on previously filtered data. Single- and two-pollutant models were tested for lags of 1-5 days and the average of the previous 2-5 days.

The increase in mortality associated with the mean levels of air pollution varied from 4 to 11%, depending on the pollutants and the way season of the year was considered. The results were not sensitive to the modeling approaches, but different effects for warmer and colder months were found. Fine particles were more important than coarse particles in the whole year and in winter, but not in summer. NO₂ and CO were also significantly associated with daily mortality, as was O₃ in the warmer months. No consistent effect was observed for SO₂. Given particle composition in Santiago, these results suggest that combustion-generated pollutants, especially from motor vehicles, may be associated with increased mortality. Temperature was closely associated with mortality. High temperatures led to deaths on the same day, while low temperatures lead to deaths from 1 to 4 days later.     

The Southeastern Aerosol Research and Characterization Study: Part II. Filter-Based Measurements of Fine and Coarse Particulate Matter Mass and Composition

Abstract

The Southeastern Aerosol Research and Characterization Study (SEARCH) was implemented in 1998–1999 to provide data and analyses for the investigation of the sources, chemical speciation, and long-term trends of fine particulate matter (PM_2.5) and coarse particulate matter (PM_10–2.5) in the Southeastern United States. This work is an initial analysis of 5 years (1999–2003) of filter-based PM_2.5 and PM_10–2.5 data from SEARCH. We find that annual PM_2.5 design values were consistently above the National Ambient Air Quality Standards (NAAQS) 15 µg/m³ annual standard only at monitoring sites in the two largest urban areas (Atlanta, GA, and North Birmingham, AL). Other sites in the network had annual design values below the standard, and no site had daily design values above the NAAQS 65 µg/m³ daily standard. Using a particle composition monitor designed specifically for SEARCH, we found that volatilization losses of nitrate, ammonium, and organic carbon must be accounted for to accurately characterize atmospheric particulate matter. In particular, the federal reference method for PM_2.5 underestimates mass by 3–7% as a result of these volatilization losses. Organic matter (OM) and sulfate account for ≥60% of PM_2.5 mass at SEARCH sites, whereas major metal oxides (MMO) and unidentified components (“other”) account for ≥80% of PM_10–2.5 mass. Limited data suggest that much of the unidentified mass in PM_10–2.5 may be OM. For paired comparisons of urban-rural sites, differences in PM_2.5 mass are explained, in large part, by higher OM and black carbon at the urban site. For PM₁₀, higher urban concentrations are explained by higher MMO and “other.” Annual means for PM_2.5 and PM_10–2.5 mass and major components demonstrate substantial declines at all of the SEARCH sites over the 1999–2003 period (10–20% in the case of PM_2.5, dominated by 14–20% declines in sulfate and 11–26% declines in OM, and 14–25% in the case of PM_10–2.5, dominated by 17–30% declines in MMO and 14–31% declines in “ other”). Although declining national emissions of sulfur dioxide and anthropogenic carbon may account for a portion of the observed declines, additional investigation will be necessary to establish a quantitative assessment, especially regarding trends in local and regional emissions, primary carbon emissions, and meteorology.     

Assessment of Human Exposure to Ambient Particulate Matter

ABSTRACT

Recent epidemiological studies have consistently shown that the acute mortality effects of high concentrations of ambient particulate matter (PM), documented in historic air pollution episodes, may also be occurring at the low to moderate concentrations of ambient PM found in modern urban areas. In London in December 1952, the unexpected deaths due to PM exposure could be identified and counted as integers by the coroners. In modern times, the PM-related deaths cannot be as readily identified, and they can only be inferred as fractional average daily increases in mortality rates using sophisticated statistical filtering and analyses of the air quality and mortality data. The causality of the relationship between exposure to ambient PM and acute mortality at these lower modern PM concentrations has been questioned because of a perception that there is little significant correlation in time between the ambient PM concentrations and measured personal exposure to PM from all sources (ambient PM plus indoor-generated PM).

This article shows that the critical factor supporting the plausibility of a linear PM mortality relationship is the expected high correlation in time of people's exposure to PM of ambient origin with measured ambient PM concentrations, as used in the epidemiological time series studies. The presence of indoor and personal sources of PM masks this underlying relationship, leading to confusion in the scientific literature about the strong underlying temporal relationship between personal exposure to PM of ambient origin and ambient PM concentration. The authors show that the sources of PM of non-ambient origin operate independently of the ambient PM concentrations, so that the mortality effect of non-ambient PM, if any, must be independent of the effects of the ambient PM exposures.     

Determination of Levoglucosan in Atmospheric Fine Particulate Matter

Abstract

A microanalytical method suitable for the quantitative determination of the sugar anhydride levoglucosan in low-volume samples of atmospheric fine particulate matter (PM) has been developed and validated. The method incorporates two sugar anhydrides as quality control standards. The recovery standard sedoheptulosan (2,7-anhydro-β-D-altro-heptulopyranose) in 20 μL solvent is added onto samples of the atmospheric fine PM and aged for 1 hr before ultrasonic extraction with ethylacetate/ triethylamine. The extract is reduced in volume, an internal standard is added (1,5-anhydro-D-mannitol), and a portion of the extract is derivatized with 10% by volume N-trimethylsilylimidazole. The derivatized extract is analyzed by gas chromatography/mass spectrometry (GC/MS). The recovery of levoglucosan using this procedure was 69 ± 6% from five filters amended with 2 μg levoglu-cosan, and the reproducibility of the assay is 9%. The limit of detection is ～0.1 μg/mL, which is equivalent to ～3.5 ng/m³ for a 10 L/min sampler or ～8.7 ng/m³ for a 4 L/min personal sampler (assuming 24-hr integrated samples). We demonstrated that levoglucosan concentrations in collocated samples (expressed as ng/m³) were identical irrespective of whether samples were collected by PM with aerodynamic diameter ≤2.5 μm or PM with aerodynamic diameter ≤10 μm impactors. It was also demonstrated that X-ray fluorescence analysis of samples of atmospheric PM, before levoglucosan determinations, did not alter the levels of levoglucosan.     

A Cost-Effective Weighing Chamber for Particulate Matter Filters

ABSTRACT

Particulate matter (PM) is a ubiquitous air pollutant that has been receiving increasing attention in recent years due in part to the association between PM and a number of adverse health outcomes, including mortality and increases in emergency room visits and respiratory symptoms, as well as exacerbation of asthma and decrements in lung function.^1-5 As a result, the ability to accurately sample ambient PM has become important, both to researchers and to regulatory agencies. The federal reference method for the determination of fine PM as PM_2.5 in the atmosphere recommends that particle-sampling filters be conditioned and weighed in an environment with constant temperature and relative humidity (RH).⁶ It is also recommended that vibration, electrostatic charges, and contamination of the filters from laboratory air be minimized to reduce variability in filter weight measurements. These controls have typically been maintained in small, environmentally controlled “cleanrooms.” As an alternative to constructing an elaborate cleanroom, we have designed, and presented in this paper, an inexpensive weighing chamber to maintain the necessary level of humidity control.     

Organic Content of Particulate Matter In Turbine Engine Exhaust

Solid particulate matter, mainly carbon, emitted into the air from the combustion of fossil fuels contains a variety of organic species adsorbed on it. In our examination of these particulates from the combustion of kerosene type fuels in a gas turbine engine, attention was focused on polynuclear aromatic compounds, phenols, nitrosamines, and total organics. Polynuclears were determined by HPLC, GC/MS, and NMR examination. Phenols and nitrosamines were isolated and then measured by gas chromatography using a flame ionization detector and nitrogen detector. Total organics were determined by a backflush chromatographic procedure. The particulates were collected using a high capacity pumping system and 293 mm diameter teflon filters through which was passed up to 43 m³ of exhaust gas. Extraction of the organic matter was done in a Soxhlet extractor using hexane usually. The engine was operated at idle, approach, climb, and takeoff power settings with low sulfur and high sulfur (0.25%) fuels. Most of the PAH were small 3 and 4 fused ring compounds with very few, at low concentrations, of 5 and 6 fused ring species. No nitrosamines were found and except in a few cases, at low levels, no phenols. PNA and total organic levels decreased with increase in a power setting and were higher in the exhaust from low sulfur fuels. Less than 1% of the organic matter emitted by the engine was absorbed on the particulate matter. The body of information presented in the paper is directed to individuals concerned with the nature of emissions from gas turbine engines. The work was supported by a contract with the Environmental Protection Agency.     

Interactions of Sulfur Dioxide with Insoluble Suspended Particulate Matter

A laboratory study was conducted of the heterogeneous catalysis of sulfur dioxide at ppm concentrations in air by insoluble particles of CaCO₂, V₂O₅, Fe₂0₃, flyash from a coal-burning power plant, MnCO₂, activated carbon, and suspended particulate matter from urban air. The investigalion was performed by utilizing a new technique for aerosol stabilization which consists of depositing the aerosol on Teflon beads in a fluidized bed. The Teflon beads with deposited aerosol particles were then packed into a flow reactor. Progress of the chemical reaction of SO₂ with deposited particles was continuously monitored by determining the SO₂ concentrations in the reactor effluent with a microcoulometer.

In this investigation, CaCOg, V₂O₅, and flyash were essentially inert to SO₂ at room temperature. Fe₂O₃, activated carbon, MnO₂, and suspended particulate matter from urban air sorbed SO₂ from air streams with up to 14.4 ppm SO₂ in air. Evidence is presented which suggests that a substantial part of the sorbed SO₂ was physically adsorbed.

Bioassay procedures which utilize pulmonary flow resistance changes in guinea pigs to monitor response to inhaled SO₂-aerosol mixtures in air have indicated the weak or non-potentiating capacity of insoluble aerosols as contrasted to soluble aerosols. Potentiating response of an aerosol appears to be strongly associated with reaction of SO₂ in a water droplet containing aerosol ions and not with physically adsorbed SO₂ on an insoluble aerosol.     

Characterization of Particulate Matter for Three Sites in Kuwait

Abstract

Many studies have shown strong associations between particulate matter (PM) levels and a variety of health outcomes, leading to changes in air quality standards in many regions, especially the United States and Europe. Kuwait, a desert country located on the Persian Gulf, has a large petroleum industry with associated industrial and urban land uses. It was marked by environmental destruction from the 1990 Iraqi invasion and subsequent oil fires. A detailed particle characterization study was conducted over 12 months in 2004–2005 at three sites simultaneously with an additional 6 months at one of the sites. Two sites were in urban areas (central and southern) and one in a remote desert location (northern). This paper reports the concentrations of particles less than 10 µm in diameter (PM₁₀) and fine PM (PM_2.5), as well as fine particle nitrate, sulfate, elemental carbon (EC), organic carbon (OC), and elements measured at the three sites. Mean annual concentrations for PM₁₀ ranged from 66 to 93 µg/m³ across the three sites, exceeding the World Health Organization (WHO) air quality guidelines for PM₁₀ of 20 µg/m³. The arithmetic mean PM_2.5 concentrations varied from 38 and 37 µg/m³ at the central and southern sites, respectively, to 31 µg/m³ at the northern site. All sites had mean PM_2.5 concentrations more than double the U.S. National Ambient Air Quality Standard (NAAQS) for PM_2.5. Coarse particles comprised 50–60% of PM₁₀. The high levels of PM₁₀ and large fraction of coarse particles comprising PM₁₀ are partially explained by the resuspension of dust and soil from the desert crust. However, EC, OC, and most of the elements were significantly higher at the urbanized sites, compared with the more remote northern site, indicating significant pollutant contributions from local mobile and stationary sources. The particulate levels in this study are high enough to generate substantial health impacts and present opportunities for improving public health by reducing airborne PM.