Control of diesel gaseous and particulate emissions with a tube-type wet electrostatic precipitator

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NOx) from diesel exhaust emissions. The concentration of ozone (O3) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O3 analyzer were used for quantifying the inlet and outlet concentrations of CO and NOx (nitric oxide [NO] + nitrogen dioxide [NO2]), and O3 in the diesel exhaust stream. The wESP was capable of removing approximately 67-86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NOx concentration in diesel exhaust. The O3 concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

Diurnal and Weekday Variations in the Source Contributions of Ozone Precursors in California’s South Coast Air Basin

Abstract

For at least 30 years, ozone (O₃) levels on weekends in parts of California’s South Coast (Los Angeles) Air Basin (SoCAB) have been as high as or higher than on weekdays, even though ambient levels of O₃ precursors are lower on weekends than on weekdays. A field study was conducted in the Los Angeles area during fall 2000 to test whether proposed relationships between emission sources and ambient nonmethane hydrocarbon (NMHC) and oxides of nitrogen (NO_x) levels can account for observed diurnal and day-of-week variations in the concentration and proportions of precursor pollutants that may affect the efficiency and rate of O₃ formation. The contributions to ambient NMHC by motor vehicle exhaust and evaporative emissions, estimated using chemical mass balance (CMB) receptor modeling, ranged from 65 to 85% with minimal day-of-week variation. Ratios of ambient NO_x associated with black carbon (BC) to NO_x associated with carbon monoxide (CO) were approximately 1.25 ± 0.22 during weekdays and 0.76 ± 0.07 and 0.52 ± 0.07 on Saturday and Sunday, respectively. These results demonstrate that lower NO_x emissions from diesel exhaust can be a major factor causing lower NO_x mixing ratios and higher NMHC/NO_x ratios on weekends. Nonmobile sources showed no significant day-of-week variations in their contributions to NMHC. Greater amounts of gasoline emissions are carried over on Friday and Saturday evenings but are, at most, a minor factor contributing to higher NMHC/NO_x ratios on weekend mornings.     

Gaseous nitrous acid (HONO) and nitrogen oxides (NOx) emission from gasoline and diesel vehicles under real-world driving test cycles

Reactive nitrogen species emission from the exhausts of gasoline and diesel vehicles, including nitrogen oxides (NO_x) and nitrous acid (HONO), contributes as a significant source of photochemical oxidant precursors in the ambient air. Multiple laboratory and on-road exhaust measurements have been performed to estimate the NO_x emission factors from various vehicles and their contribution to atmospheric pollution. Meanwhile, HONO emission from vehicle exhaust has been under-measured despite the fact that HONO can contribute up to 60% of the total hydroxyl budget during daytime and its formation pathway is not fully understood. A profound traffic-induced HONO to NO_x ratio of 0.8%, established by Kurtenbach et al. since 2001, has been widely applied in various simulation studies and possibly linked to under-estimation of HONO mixing ratios and OH radical budget in the morning. The HONO/NO_x ratios from direct traffic emission have become debatable when it lacks measurements for direct HONO emission from vehicles upon the fast-changing emission reduction technology. Several recent studies have reported updated values for this ratio. This study has reported the measurement of HONO and NO_x emission as well as the estimation of exhaust-induced HONO/NO_x ratios from gasoline and diesel vehicles using different chassis dynamometer tests under various real-world driving cycles. For the tested gasoline vehicle, which was equipped with three-way catalyst after-treatment device, HONO/NO_x ratios ranged from 0 to 0.95 % with very low average HONO concentrations. For the tested diesel vehicle equipped with diesel particulate active reduction device, HONO/NO_x ratios varied from 0.16 to 1.00 %. The HONO/NO_x ratios in diesel exhaust were inversely proportional to the average speeds of the tested vehicles.

Implications: Photolysis of HONO is a dominant source of morning OH radicals. Conventional traffic-induced HONO/NO_x ratio of 0.8% has possibly linked to underestimation of the total HONO budget and consequently underestimation of OH radical budget. The recently reported HONO/NO_x ratio of ~1.6% was used to stimulate HONO emission, which resulted in increased HONO concentrations during morning peak hours and its impact of 14% OH increment in the morning. However, the results were still lower than the measured concentrations. More studies should be conducted to establish an updated traffic-induced HONO/NO_x ratio.     

Analysis of NO,NO2, O3 and NOx concentrations measured at a green area of Buenos Aires City during wintertime

We analyse the air quality data measured at a green area of Buenos Aires City (Argentina) during 38 days in winter. We study the relationships between ambient concentrations of nitric oxide (NO), nitrogen dioxide (NO₂), ozone (O₃) and nitrogen oxides (NO_x=NO+NO₂). The variation of the level of oxidant (OX=O₃+NO₂) with the NO_x is obtained. It can be seen that the level of OX at a given location is made up of two contributions: one independent and another dependent on the NO_x concentration. The first one can be considered as a regional contribution, equivalent to the background O₃ concentration and the second one as a local contribution that depends on the level of primary pollution. Local oxidant sources may include direct NO₂ emissions, the reaction of NO with O₂ at high-NO_x levels, and the emission of species that promote the conversion of NO to NO₂. The final category of emissions may include the nitrous acid (HONO) that is emitted directly in vehicle exhaust. Finally, we present a diurnal variation of the local as well as regional contributions and the dependence of the last one on wind direction.     

生物滤塔和NRB在有氧条件下去除废气中的NOx

研究了有氧条件下氮氧化物在生物滤塔内的传质机理,结果表明,当含NOx废气中氧气含量为20%、氧化度为80%时,被生物滤塔内微生物吸附分解的NOx仅占被净化的NOx的12%左右,而88%左右的NOx没有被微生物及时分解,而是转入液相中形成NO3-和NO2-.在此基础上,提出了采用生物滤塔和硝酸盐脱除反应器(nitrate...     

Responses of herbaceous plants to urban air pollution: Effects on growth, phenology and leaf surface characteristics

Vehicle exhaust emissions are a dominant feature of urban environments and are widely believed to have detrimental effects on plants. The effects of diesel exhaust emissions on 12 herbaceous species were studied with respect to growth, flower development, leaf senescence and leaf surface wax characteristics. A diesel generator was used to produce concentrations of nitrogen oxides (NO_x) representative of urban conditions, in solardome chambers. Annual mean NO_x concentrations ranged from 77 nl l^−l to 98 nl l⁻¹, with NO:NO₂ ratios of 1.4-2.2, providing a good experimental simulation of polluted roadside environments. Pollutant exposure resulted in species-specific changes in growth and phenology, with a consistent trend for accelerated senescence and delayed flowering. Leaf surface characteristics were also affected; contact angle measurements indicated changes in surface wax structure following pollutant exposure. The study demonstrated clearly the potential for realistic levels of vehicle exhaust pollution to have direct adverse effects on urban vegetation.     

Influence of nocturnal vertical stability on daytime chemistry: A one-dimensional model study

Nocturnal chemistry can play an important role in determining the initial morning conditions for daytime chemistry in urban areas. However, the impact on daytime O₃ levels is difficult to assess as the suppression of vertical trace gas transport leads to highly altitude dependent nocturnal chemistry, in particular with respect to the removal and conversion of nitrogen oxides (NO_x) and volatile organic compounds (VOC). One-dimensional (1-D) chemical transport model calculations for different nighttime vertical stabilities and different ozone formation regimes (i.e. NO_x- vs. VOC-sensitive) were performed assuming a 1000 m high daytime boundary layer and a growing nocturnal boundary layer reaching 200 m height at the end of the night. Exclusion of NO₃ chemistry from the model leads to daytime O₃ concentration changes from ?4% to +16% for different O₃ sensitivities. In all cases strong nocturnal vertical concentration profiles of NO_x, O₃, NO₃ and N₂O₅ and a dependence of these profiles on vertical stability were found at night. The nocturnal NO_x loss averaged over the lowest 1000 m changes by 9–24% for different vertical stabilities and ozone sensitivities. The impact of nocturnal vertical stability leads to 7–12% difference in O₃ concentration in the morning and ～0–2.5% in the afternoon.     

Simultaneous removal of NOx,SO2, and Hg from flue gas in FGD absorber with oxidant injection (NaClO2)– full-scale investigation

ABSTRACT

This article presents the results of an industrial-scale study (on 400 MW_e lignite fired unit) of simultaneous NO_x, SO₂, and Hg^T removal in FGD absorber with oxidant injection (NaClO₂) into flue gas. It was confirmed that the injection of sodium chlorite upstream the FGD (Flue Gas Desulfurization) absorber oxidize NO to NO₂, Hg⁰ to Hg²⁺, and enhancing NO_x and Hg^T removal efficiency from exhaust gas in FGD absorber. Mercury removal efficiency grows with the rise of degree of oxidation NO to NO₂ and was limited by the phenomenon of re-emission. For NO_x removal the most critical parameters is slurry pH and temperature. There was no negative effect on sulfur dioxide removal efficiency caused by oxidant injection in tested FGD absorber. Based on the data provided, NO_x and Hg^T emissions can be reduced by adjusting the FGD absorber operating parameters combined with oxidant injection.     

A Fuel-Based Assessment of Off-Road Diesel Engine Emissions

ABSTRACT

The use of diesel engines in off-road applications is a significant source of nitrogen oxides (NO_x) and particulate matter (PM₁₀). Such off-road applications include railroad locomotives, marine vessels, and equipment used for agriculture, construction, logging, and mining. Emissions from these sources are only beginning to be controlled. Due to the large number of these engines and their wide range of applications, total activity and emissions from these sources are uncertain. A method for estimating the emissions from off-road diesel engines based on the quantity of diesel fuel consumed is presented. Emission factors are normalized by fuel consumption, and total activity is estimated by the total fuel consumed.

Total exhaust emissions from off-road diesel equipment (excluding locomotives and marine vessels) in the United States during 1996 have been estimated to be 1.2 × 10⁹ kg NO_x and 1.2 x 10⁸ kg PM₁₀. Emissions estimates published by the U.S. Environmental Protection Agency are 2.3 times higher for both NO_x and exhaust PM₁₀ emissions than estimates based directly on fuel consumption. These emissions estimates disagree mainly due to differences in activity estimates, rather than to differences in the emission factors. All current emission inventories for off-road engines are uncertain because of the limited in-use emissions testing that has been performed on these engines. Regional- and state-level breakdowns in diesel fuel consumption by off-road mobile sources are also presented. Taken together with on-road measurements of diesel engine emissions, results of this study suggest that in 1996, off-road diesel equipment (including     

Idle Emissions from Medium Heavy-Duty Diesel and Gasoline Trucks

Abstract

Idle emissions data from 19 medium heavy-duty diesel and gasoline trucks are presented in this paper. Emissions from these trucks were characterized using full-flow exhaust dilution as part of the Coordinating Research Council (CRC) Project E-55/59. Idle emissions data were not available from dedicated measurements, but were extracted from the continuous emissions data on the low-speed transient mode of the medium heavy-duty truck (MHDTLO) cycle. The four gasoline trucks produced very low oxides of nitrogen (NO_x) and negligible particulate matter (PM) during idle. However, carbon monoxide (CO) and hydrocarbons (HCs) from these four trucks were approximately 285 and 153 g/hr on average, respectively. The gasoline trucks consumed substantially more fuel at an hourly rate (0.84 gal/hr) than their diesel counterparts (0.44 gal/hr) during idling. The diesel trucks, on the other hand, emitted higher NO_x (79 g/hr) and comparatively higher PM (4.1 g/hr), on average, than the gasoline trucks (3.8 g/hr of NO_x and 0.9 g/hr of PM, on average). Idle NO_x emissions from diesel trucks were high for post-1992 model year engines, but no trends were observed for fuel consumption. Idle emissions and fuel consumption from the medium heavy-duty diesel trucks (MHDDTs) were marginally lower than those from the heavy heavy-duty diesel trucks (HHDDTs), previously reported in the literature.     

Predictive NOx emission monitoring on board a passenger ferry

NO_x emissions from a medium speed diesel engine on board a servicing passenger ferry have been indirectly measured using a predictive emission monitoring system (PEMS) over a 1-yr period. Conventional NO_x measurements were carried out with a continuous emission monitoring system (CEMS) at the start of the study to provide historical data for the empirical PEMS function. On three other occasions during the year the CEMS was also used to verify the PEMS and follow any changes in emission signature of the engine. The PEMS consisted of monitoring exhaust O₂ concentrations (in situ electrochemical probe), engine load, combustion air temperature and humidity, and barometric pressure. Practical experiences with the PEMS equipment were positive and measurement data were transferred to a land-based office by using a modem data communication system. The initial PEMS function (PEMS1) gave systematic differences of 1.1–6.9% of the calibration domain (0–1725 ppm) and a relative accuracy of 6.7% when compared with CEMS for whole journeys and varying load situations. Further improvements on the performance could be obtained by updating this function. The calculated yearly emission for a total engine running time of 4618 h was 316 t NO_x±38 t and the average NO_x emission corrected for ambient conditions 14.3 g kWh_corr⁻¹. The exhaust profile of the engine in terms of NO_x, CO and CO₂ emissions as determined by CEMS was similar for most of the year. Towards the end of the study period, a significantly lower NO_x emission was detected which was probably caused by replacement of fuel injector nozzles. The study suggests that PEMS can be a viable option for continuous, long-term NO_x measurements on board ships.     

Analysis of the relationship between ambient levels of O3, NO2 and NO as a function of NOx in the UK

Monitoring data from the UK Automatic Urban and Rural Network are used to investigate the relationships between ambient levels of ozone (O₃), nitric oxide (NO) and nitrogen dioxide (NO₂) as a function of NO_x, for levels ranging from those typical of UK rural sites to those observed at polluted urban kerbside sites. Particular emphasis is placed on establishing how the level of ‘oxidant’, OX (taken to be the sum of O₃ and NO₂) varies with the level of NO_x, and therefore to gain some insight into the atmospheric sources of OX, particularly at polluted urban locations. The analyses indicate that the level of OX at a given location is made up of NO_x-independent and NO_x-dependent contributions. The former is effectively a regional contribution which equates to the regional background O₃ level, whereas the latter is effectively a local contribution which correlates with the level of primary pollution. The local oxidant source has probable contributions from (i) direct NO₂ emissions, (ii) the thermal reaction of NO with O₂ at high NO_x, and (iii) common-source emission of species which promote NO to NO₂ conversion. The final category may include nitrous acid (HONO), which appears to be emitted directly in vehicle exhaust, and is potentially photolysed to generate HO_x radicals on a short timescale throughout the year at southern UK latitudes. The analyses also show that the local oxidant source has significant site-to-site variations, and possible reasons for these variations are discussed. Relationships between OX and NO_x, based on annual mean data, and fitted functions describing the relative contributions to OX made by NO₂ and O₃, are used to define expressions which describe the likely variation of annual mean NO₂ as a function of NO_x at 14 urban and suburban sites, and which can take account of possible changes in the regional background of O₃.     

Revised estimates of construction activity and emissions: Effects on ozone and elemental carbon concentrations in southern California

Emissions from diesel-powered construction equipment are an important source of nitrogen oxides (NO_x) and particulate matter (PM). A new emission inventory for construction equipment emissions is developed based on surveys of diesel fuel use; the revised inventory is compared to current emission inventories. California's OFFROAD model estimates are 4.5 and 3.1 times greater, for NO_x and PM respectively, than the fuel-based estimates developed here. The most relevant uncertainties are the overall amount of construction activity/diesel fuel use, exhaust emission factors for PM and NO_x, and the spatial allocation of emissions to county level and finer spatial scales. Construction permit data were used in this study to estimate spatial distributions of emissions; the resulting distribution is well correlated with population growth. An air quality model was used to assess the impacts of revised emission estimates. Increases of up to 15 ppb in predicted peak ozone concentrations were found in southern California. Elemental carbon and fine particle mass concentrations were in better agreement with observations using revised emission estimates, whereas negative bias in predictions of ambient NO_x concentrations increased.     

Application of CALINE4 to roadside NO/NO2 transformations

The CALINE4 roadway dispersion model has been applied to concentrations of NO_x and NO₂ measured near Gandy Boulevard in Tampa, FL (USA) during May 2002. A NO_x emission factor of 0.86 gr mi⁻¹ was estimated by treating NO+NO₂ (NO_x) as a conserved species and minimizing the differences between measured and calculated NO_x concentrations. This emission factor was then used to calculate NO₂ concentrations using the NO/NO₂ transformation reactions built into CALINE4. A comparison of measured and calculated NO₂ concentrations indicates that for ambient O₃ concentrations less than 40 ppb the model under-predicts the chemical transformation of NO. The enhanced transformation of NO may be due to reactions of NO with oxidants such as peroxy radicals that are present either in the atmosphere or in vehicle exhaust.     

Trend of vehicle emission levels until 2020 – Prognosis based on current vehicle measurements and future emission legislation

The paper describes the incorporation of actual emission measurements and future emission standards into the emission model ‘NEMO’ (Network Emission Model). This model is then applied to make predictions on vehicle emission levels on basis of the Austrian fleet composition until 2020. The output is compared to the results based on the most common emission tool for the calculation of vehicle emissions in Central Europe – the recent version (2.1) of the ‘Handbook Emission Factors for Road Transport’. The discussion is focused on NO_x and particulate matter (PM), since these pollutants are considered to be the most critical for the local air quality level.The NO_x emission levels of recent modern diesel vehicle generations observed in several real world driving conditions were observed to be clearly higher than demanded in the type approval procedure. Due to the growing number of modern diesel engine concepts equipped with coated catalytic exhaust after treatment, the fraction of NO₂ of the total tailpipe NO_x emissions is predicted to continue to increase in the next few years. Bearing in mind the upcoming tightening of the NO₂ air quality limits and the steady increase of traffic volumes, excesses of the NO₂ air quality limits at roadside locations have to be expected to an increasing extent for the beginning of the next decade. The issue of particle emissions originated from the diesel engine combustion process can be regarded as being technically solved due to the extensive introduction of diesel particle filters in the vehicle fleet if these systems will prove a high efficiency over the entire vehicle life in real world operation conditions. However, PM emissions from road transport will continue to be in the focus of public attention due to particle emissions caused by dust re-suspension and abrasion processes.     

低温等离子体处理柴油机NOx和PM试验研究

建立了一种具有较强实用性的介质阻挡放电等离子体反应器试验装置.借助静态试验研究其放电特性,通过发动机台架试验探讨了利用低温等离子体处理柴油机2种主要有害排放物NOx和PM的效果和化学反应机理,并通过模拟试验作了处理PM的进一步验证.试验结果表明,放电功率对于低温等离子体活性成分的产生有重要影响,应当优选放电参数以获得高的放电功率从而达到更好的处理效果;采用低温等离子体处理柴油机排气,NOx总量变化不大,主要将NO转化成NO2;低温等离子体可以有效去除柴油机排气中的PM,去除率随能量密度的增大而提高.     

Study of Miller timing on exhaust emissions of a hydrotreated vegetable oil (HVO)-fueled diesel engine

The effect of intake valve closure (IVC) timing by utilizing Miller cycle and start of injection (SOI) on particulate matter (PM), particle number, and nitrogen oxide (NO_x) emissions was studied with a hydrotreated vegetable oil (HVO)-fueled nonroad diesel engine. HVO-fueled engine emissions, including aldehyde and polyaromatic hydrocarbon (PAH) emissions, were also compared with those emitted with fossil EN590 diesel fuel. At the engine standard settings, particle number and NO_x emissions decreased at all the studied load points (50%, 75%, and 100%) when the fuel was changed from EN590 to HVO. Adjusting IVC timing enabled a substantial decrease in NO_x emission and combined with SOI timing adjustment somewhat smaller decrease in both NO_x and particle emissions at IVC??50 and??70 °CA points. The HVO fuel decreased PAH emissions mainly due to the absence of aromatics. Aldehyde emissions were lower with the HVO fuel with medium (50%) load. At higher loads (75% and 100%), aldehyde emissions were slightly higher with the HVO fuel. However, the aldehyde emission levels were quite low, so no clear conclusions on the effect of fuel can be made. Overall, the study indicates that paraffinic HVO fuels are suitable for emission reduction with valve and injection timing adjustment and thus provide possibilities for engine manufacturers to meet the strictening emission limits.

Implications: NO_x and particle emissions are dominant emissions of diesel engines and vehicles. New, biobased paraffinic fuels and modern engine technologies have been reported to lower both of these emissions. In this study, even further reductions were achieved with engine valve adjustment combined with novel hydrotreated vegetable oil (HVO) diesel fuel. This study shows that new paraffinic fuels offer further possibilities to reduce engine exhaust emissions to meet the future emission limits.

Supplementary Materials: Supplementary materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association for a complete list of analysed PAH compounds.     

Generation and Characterization of Diesel Exhaust in a Facility for Controlled Human Exposures

Abstract

An idling medium-duty diesel truck operated on ultralow sulfur diesel fuel was used as an emission source to generate diesel exhaust for controlled human exposure. Repeat tests were conducted on the Federal Test Procedure using a chassis dynamometer to demonstrate the reproducibility of this vehicle as a source of diesel emissions. Exhaust was supplied to a specially constructed exposure chamber at a target concentration of 100 µg · m^-3 diesel particulate matter (DPM). Spatial variability within the chamber was negligible, whereas emission concentrations were stable, reproducible, and similar to concentrations observed on the dynamometer. Measurements of nitric oxide, nitrogen dioxide, carbon monoxide, particulate matter (PM), elemental and organic carbon, carbonyls, trace elements, and polycyclic aromatic hydrocarbons were made during exposures of both healthy and asthmatic volunteers to DPM and control conditions. The effect of the so-called “personal cloud” on total PM mass concentrations was also observed and accounted for. Conventional lung function tests in 11 volunteer subjects (7 stable asthmatic) did not demonstrate a significant change after 2-hr exposures to diesel exhaust. In summary, we demonstrated that this facility can be effectively and safely used to evaluate acute responses to diesel exhaust exposure in human volunteers.     

Effect of Hydrocarbon and NO x on Photochemical Smog Formation under Simulated Transport Conditions

The body of information presented in this paper is directed to those individuals concerned with the effect of urban pollution on downwind areas. Concern has been expressed over the appropriate hydrocarbon and NO _x control strategy to be used in minimizing the effects of ozone and NO₂ on urban population centers and their downwind environs. O₃ and NO₂ formation were studied in smog chamber irradiations as a function of the initial NO _x concentration at three hydrocarbon concentrations. By carrying out the irradiations for a period of time equivalent to one solar day in a continuously diluting system, smog formation in a chemically reacting pollutant system under transport was simulated. The results of this experimental simulation suggest that hydrocarbon reduction reduces O₃ in urban as well as downwind areas while NO _x reduction increases O₃ in the urban area and has little effect on O₃ in downwind areas. Both hydrocarbon and NO _x reduction will reduce atmospheric NO₂ levels, with the effect of NO _x reduction generally being more pronounced.     

Ground level ozone concentrations and its association with NOx and meteorological parameters in Kathmandu valley, Nepal

This paper summarizes the results of a yearlong continuous measurements of gaseous pollutants, NO, NO₂, NO_x and O₃ in the ambient air at Kathmandu valley. Measured concentration of the pollutants in study area is a function of time. NO, NO₂ and O₃ peak occurred in succession in presence of sunlight. At the time of maximum O₃ concentration most of the NO_x are utilized. The diurnal cycle of ground level ozone concentrations, revealed mid-day peak with lower nocturnal concentrations and inverse relationship exists between O₃ and NO_x, which are evidences of photochemical O₃ formation. The observed ground level ozone during monsoon is slight lower than the pre-monsoon value. Further, lack of rainfall and higher temperature, solar radiation in the pre-monsoon have given rise to the gradual build up of ozone and it is lowest during winter. Ground level ozone concentrations measured during bandha (general strike) and weekend are 19% and 13% higher than those measured during weekdays. The most effective ozone abatement strategy for Kathmandu Valley may be control of NO_x emissions.