Sunflower stalk, an agricultural waste, as an adsorbent for the removal of lead and cadmium from aqueous solutions

Sunflower residue, an agricultural waste material for the removal of lead (Pb) and cadmium (Cd) from aqueous solutions were investigated using a batch method. Adsorbent was prepared by washing sunflower residue with deionized water until the effluent was colorless. Batch mode experiments were carried out as a function of solution pH, adsorbent dosage, initial concentration and contact time. The results indicated that the adsorbent showed good sorption potential and maximum metal removal was observed at pH 5. Within 150 min of operation about 97 and 87 % of Pb and Cd ions were removed from the solutions, respectively. Lead and Cd sorption curves were well fitted to the modified two-site Langmuir model. The adsorption capacities for Pb and Cd at optimum conditions were 182 and 70 mg g^?1, respectively. The kinetics of Pb and Cd adsorption from aqueous solutions were analyzed by fitting the experimental data to a pseudo-second-order kinetic model and the rate constant was found to be 8.42 × 10^?2 and 8.95 × 10^?2 g mg^?1 min^?1 for Cd and Pb, respectively. The results revealed that sunflower can adsorb considerable amount of Pb and Cd ions and thus could be an economical method for the removal of Pb and Cd from aqueous systems.     

Phosphorus recovery from secondary effluent and side-stream liquid in a sewage treatment plant using zirconium-loaded saponified orange waste

Zirconium was loaded onto orange waste, a cheap and available agricultural waste in Japan, to investigate the feasibility of its utilization for phosphorus recovery from secondary effluent and side-stream liquid, which contain 5.9 and 68.2 mg/dm³ phosphorus, respectively. The phosphorus removal from side-stream liquid by using zirconium-loaded saponified orange waste (Zr-SOW) gel increased with an increasing solid/liquid ratio, and it was found that Zr-SOW gel showed better performance than zirconium ferrite. The prepared adsorbent was effective for phosphorus removal and exhibited a reasonably high adsorption capacity, twice than that of zirconium ferrite. The secondary effluent was treated in a column packed with Zr-SOW gel, and an dynamic adsorption capacity of 1.3 mol-P/kg was attained. The adsorbed phosphorus from the column was successfully eluted as a concentrated form by using a small amount of 0.2 M NaOH. Throughout the elution process, zirconium was not leaked from the adsorption gel.     

Investigation of the Thermosensitive Nanosphere Polymer in Removing Organophosphorus Pesticides from Water and Its Isotherm Study (Case Study: Diazinon)

In this research, a novel thermosensitive nanosphere polymer (TNP) was synthesized by copolymerization of N-isopropylacrylamide with 3-allyloxy-1,2-propanediol for the removal of diazinon from water. The characterization of the synthesized adsorbent has been performed by Fourier transform infrared spectrometer, scanning electron microscopy and elemental analysis. Batch adsorption method was performed to investigate the influences of various parameters like pH, temperature and contact time on the adsorption of diazinon. The equilibrium adsorption data of diazinon by TNP was studied by Langmuir, Freundlich, Temkin and Redlich–Peterson model. According to equilibrium adsorption results, the Langmuir, Freundlich and Temkin constants were evaluated to be 0.912 (L/mg), 7.916 (mg/g) (L/mg)^1/n and 2.494 respectively at pH 7 and room temperature. Based on Redlich–Peterson model analysis, the equilibrium data for the adsorption of diazinon was conformed well to the Langmuir isotherm model. This method was successfully applied for removal of diazinon from environmental samples. Moreover, in reusing of TNP, the sorption capacity was maintained without any significant change after 10 cycles of sorption–desorption process.     

Aqueous leaching of cattle manure incineration ash to produce a phosphate enriched fertilizer

Ash produced from the combustion of livestock manure contains large amounts of phosphorus (P), which is an important resource as a fertilizer. Some studies have extracted and recovered P from incinerated biomass ash using inorganic acid or alkaline agents, which produce wastewater that requires treatment and is expensive due to the cost of chemicals. Livestock manure ash contains not only P, but also water soluble salts, which could be a negative influence on plant growth and shall be preferably removed from the recovered fertilizer. In this study, we removed salinity from cattle manure incineration ash by simple aqueous leaching, while retaining the P content. The optimal condition was a 20 min leaching time at a liquid/solid (L/S) ratio of 10 mL g-ash^?1. Under this condition, over 90 % of Cl and 20 % of Na in the original ash was removed, while over 99 % of the P was retained in the leached residue. The leached residue met the fertilizer standard in Japan in terms of citrate soluble fertilizer components and contained few heavy metals. X-ray analyses of the ash indicated that Cl was mainly present as KCl in the original ash, while P was mainly present as Ca compounds in the ash.     

Terrestrial physical and chemical processes for liquid waste treatment

Experiences gained from full-scale evaluation of advanced treatment processes used for reclaiming wastewaters should help in the evaluation of potential treatment systems for treatment and reuse of water in space. Water Factory 21 is a 0.66 m³s⁻¹ (15 million gallons per day) water reclamation plant in California that has been in operation since 1976. The plant receives biologically treated wastewater. Lime treatment is effective for removal of heavy metals. Volatile organic constitutes are efficiently removed by air stripping. Non-volatile organic constituents are removed by activated carbon adsorption and reverse osmosis (RO). RO is a highly effective polishing step, and removes most of the remaining materials including inorganic salts, heavy metals, and organics. RO removed 85% of the total organic carbon, down to about 1 mg 1⁻¹, which is lower than in many treated drinking waters. The series of treatment processes used insured virus and pathogen removal, with lime treatment and chlorination together proving highly effective. Sufficient data has been collected to provide statistically reliable confidence limits to be set on the performance of each unit process.     

Removal of mercury from flue gas using sewage sludge-based adsorbents

Mercury from coal-fired utility boilers, as the largest atmospheric mercury emission source, imposes serious environmental risks and health concerns. In order to explore the possibility of reducing costs of activated carbon injection, we investigated the most promising mercury control technology, Hg⁰ removal using ZnCl₂-impregnated adsorbents derived from sewage sludge. The results demonstrated that sludge-based adsorbents (SBAs) had fairly high mercury adsorption capacity over a wide range of temperatures (80–170 °C). Oxidizing atmosphere could improve the adsorption of Hg⁰ and weaken the inhibition of SO₂ on mercury adsorption to some extent. NO exhibited no obvious impact on mercury removal performance. In addition, to clarify whether oxygen- or chlorine-containing functional groups attributed to good mercury adsorption capacity of SBAs, the oxygen-containing functional groups were removed using Boehm’s method, and a temperature-programmed decomposition desorption experiment was conducted. The results suggest that chlorine-containing functional groups played a significant role in the removal process of mercury from flue gas using SBAs.     

Experimental study of behavior of endocrine-disrupting chemicals in leachate treatment process and evaluation of removal efficiency

An experimental study of the behavior of endocrine-disrupting chemicals (EDCs) in leachate treatment processes (aeration, coagulation and sedimentation, activated carbon adsorption, and advanced oxidation) was conducted and removal efficiencies were evaluated. Among target EDCs, concentrations of BPA (1800 times), DBP (10 times), BBP (40 times), and DEHP (30 times) in leachate are more than ten times higher than those in surface water. BPA, DBP, and BBP can be treated by aeration and DEHP, by advanced oxidation processes. BPA could not be effectively removed by coagulation and sedimentation because most of BPA partitioned in the supernatant. DEHP could hardly be treated by aeration. The removal ratios of DEHP were approximately 50–70% if the generated sediment was removed completely. The removal ratios of DEHP in leachate of 100 m³/d with 100 kg of activated carbon were 50–70%, assuming a complete mixing model. The concentration of DEHP was decreased to below one-tenth in 120 min by advanced oxidation processes.     

Biosorptive removal of Pb(II) and Cu(II) from wastewater using activated carbon from cassava peels

The ability of activated carbon from cassava peels to remove heavy metals like Cu(II) and Pb(II) from hospital wastewater was investigated. The study showed that a pH of 8 was the best for the sorption of both metal ions onto the biosorbent. The time-dependent experiments for the metal ions showed that the binding of the metal ions to the biomass was rapid and occurred within 20–120 min. Sorption efficiency increased with a rise in adsorbent dosage. It increased from 12 to 73 % for Pb(II) and 26 to 79 % for Cu(II) when the adsorbent dose increased from 2 to 12 g. An increase in temperature led to an increase in sorption for both metal ions. The Langmuir model showed that the biomass has a higher sorption capacity for Cu(II) than Pb(II), with q _m = 5.80 mg g^?1 for Pb(II) and 8.00 mg g^?1 for Cu(II). The Freundlich isotherm K _f was 1.4 for Pb(II) and 1.8 for Cu(II), indicating a preferential sorption of Cu(II) onto the biosorbent. Adsorption capacity was found to decrease with an increase in particle sizes. Sorption occurred by physical mechanisms and was mainly controlled by intraparticle diffusion.     

Removal of substituted phenols onto iron‐treated Nostoc sp. biomass

This study explored the possibility of removing 4‐nitrophenol (4‐NP) and 2,4‐dichlorophenol (2,4‐DCP) from water by using a dead blue‐green algae, Nostoc sp., dried and untreated and dried and treated with iron (Fe‐treated with 0.1 M ferric chloride solution for 1 day). The Nostoc sp. untreated and Fe‐treated biomass were used to study the sorption and desorption of 4‐NP and 2,4‐DCP. The effects of solute concentration, ionic strength, and temperature on sorption and desorption in the presence of untreated and treated Nostoc sp. biomass were investigated. The Fe‐treated Nostoc sp. biomass sorbed higher amounts of both 4‐NP and 2,4‐DCP than the untreated biomass. The percent cumulative desorption decreased from 6.41% to 0.28% and 1.84% to 0.19%, respectively, for 4‐NP and 2,4‐DCP for the Fe‐treated biomass. Biosorption of 4‐NP and 2,4‐DCP onto untreated and Fe‐treated Nostoc sp. biomass conformed to Freundlich isotherms. Iron treatment of Nostoc sp. biomass increased the value of ln K from 8.07 to 8.59 for 4‐NP and from 8.04 to 8.51 for 2,4‐DCP but decreased their desorption. An increase in ionic strength (0.003–0.03) increased the biosorption of both substituted phenols and decreased their percent desorption. An increase in temperature in the range of 15–35°C decreased the sorption of 4‐NP and 2,4‐DCP onto both untreated and Fe‐treated Nostoc sp. biomass and increased their desorption, indicating that the biosorption of both substituted phenols onto untreated and Fe‐treated Nostoc sp. biomass was principally a physical process. The results of this study suggest that Fe‐treated dried Nostoc sp. biomass could be explored as an inexpensive and eco‐friendly material for the effective removal of these phenols and, potentially, other chemicals from industrial wastewater and contaminated groundwater.     

Adsorption Efficiency of Polyaspartate-Montmorillonite Composite Towards the Removal of Pb(II) and Cd(II) from Aqueous Solution

The selective modification of sodium montmorillonite (Na⁺-Mt) surface with polyionene followed by poly (succinimde-co-aspartate) has been considered. Na⁺-Mt was allowed to react with well characterized polyionene in two fold excess. The resulting polyionene/Mt (IC) was further modified with poly (succinimide-co-aspartate) through an ion exchange process. The obtained polyaspartate/Mt (IPS) composite was characterized by elemental analysis, X-ray diffraction, FTIR spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and BET surface analyzer. The adsorption efficiency of IPS composite was investigated for the removal of Pb(II) and Cd(II) from aqueous solution under different experimental conditions including initial metal ions concentration, temperature and single and binary mixture systems of metal ions. The experimental data were analyzed by Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models. Langmuir model reveals that the monolayer adsorption capacity of IPS was 92.59 and 67.57 mg/g for Pb(II) and Cd(II), respectively. The modification of parent Na⁺-Mt enhanced their adsorption capacity by about 87.91 and 29.84% for Pb(II) and Cd(II), respectively, due to inclusion of extra active sites of polyaspartate. The mean sorption energy, E calculated from Dubinin–Radushkevich isotherm were 2.75 and 1.98 kJ/mol for the adsorption of Pb(II) and Cd(II), respectively, indicating physical adsorption process. Also, The thermodynamic parameters were calculated and indicated that the adsorption was spontaneous and exothermic process. The mechanism of cation exchange and complexation of metal ions was suggested. IPS composite has a considerable potential for the removal of heavy metal ions from aqueous solution and wastewater stream.     

Remediation of Persistent Organic Pollutants Using a Novel Two-Phase Soil Washing Biosorption Process

A two-phase soil washing biosorption process was developed for the remediation of p,p-DDT-contaminated soil. The process involved desorption of contaminants from soil using dilute primary alcohols (40% 1-propanol) followed by contaminant removal from cosolvent solutions using fungal biosorption. Bench scale remediation studies were preformed to simulate ex situ (recycling experiment) or in situ (soil column study) treatment strategies. Both systems were effective at cleaning the soil to below Australian regulatory p,p-DDT levels. After 50–80 hours of soil washing, over 93% of p,p-DDT was removed from the soil(990 mg kg^-1 to <65 mg kg^-1) using either of these methods.p,p-DDT was removed from the cosolvent phase by sorption onto the fungal biomass. This resulted in only low levels of p,p-DDT remaining in the cosolvent solution(<1.5 mg l^-1). The application of both treatment strategies resulted in the rapid clean up of p,p-DDT-contaminated soil and the potential to recycle cosolvent solutions. The ability to recycle cosolvent solutions provides a mechanism for cost reductions of the remediation strategy.     

Treatment of creosote-contaminated groundwater in vegetated sorption/bio-barriers in cold climates

Permeable barriers are structures installed in situ to treat contaminated groundwater. Pollutants are removed as contaminated groundwater flows through a barrier material. A compost/sand barrier and a plant covered permeable barrier with soil/sand and peat/sand were tested in pilot-scale to treat creosote-contaminated groundwater by sorption and biological removal in situ. Outlet concentrations of the barriers were consistently low during the 29 months of operation. Although sorption sites were filled up with polycyclic aromatic hydrocarbons, they seemed to be regenerated because of biodegradation under aerobic conditions. The vegetated section was least efficient, probably because of lack of oxygen, hence it could not be determined if the plants had a positive effect. As long as biodegradation is efficient the barrier is expected to function for several more years.     

Nutrient export and material recycling using aquatic plants: Lake Kitagata case study

Lake Kitagata in Fukui Prefecture, Japan, was examined to collect fundamental data on nutrient export and material recycling using the native aquatic plants, common reed and wild rice. Common reed was located all over the lake shore, while wild rice was in the upper part of the lake. On average, the nutrient content was nitrogen: 2.1 and 2.6?%, P₂O₅: 0.38 and 0.64?%, K₂O: 2.1 and 2.4?% for common reed and wild rice, respectively, and decreased along with their growth. If harvested in October, the nitrogen and phosphorus exported from the lake were estimated to be only 1.1 and 1.9?% of the inflow, respectively. Methane fermentation of these plants showed an average of 134 and 150?mL-CH₄/g-VS added for common reed and wild rice, respectively, indicating possible use as an auxiliary source. The composting of these plants mixed with chicken manure, bean curd and rice bran was successful, and the products were rich in the major nutrients and well-balanced. A pretreatment method combining sulfuric acid and thermal treatment was able to convert about 50?% of cellulose in common reed to glucose, the precursor for bioethanol production. Therefore, these technologies are demonstrated to be helpful for the beneficial use of the biomass.     

Loblolly pine response to wet-weather harvesting on wet flats after 5 years

The timing of forestry operations relative to weather conditions is a consideration in applying Forestry Best Management Practices (BMPs). Harvesting during different seasons can result in degrees of soil disturbance, the distribution of logging debris, and potentially future stand productivity. The purpose of this study is to examine the response of loblolly pine (Pinus taeda L.) stands after wet- and dry-weather harvesting combined with three site preparation treatments. A 20 × 20 meter grid was established in fifteen 20-year-old, 3.3-ha loblolly pine plantations in South Carolina. A census of soil physical disturbance and slash distribution was made after harvesting. Growth was measured on 1/125th-ha plots at ages two and five. Dry-weather harvested (DWH) sites were 91% undisturbed, and 9% compressed. Wet-weather harvested (WWH) sites were 41% undisturbed, and 59% disturbed. WWH sites averaged 9% bare soil, while DWH sites averaged 16% with 1 kg m^-2 less logging residue; primarily in the form of heavy and light slash. At age five, the green-weight biomass of flat-planted DWH and WWH sites were 13.3 and 12.6 kg tree^-1 respectively, and on the bedded DWH and WWH sites were 18.6 and 22.8 kg tree^-1. Wet weather harvesting did not seem to adversely affect stand growth, and may have improved it. Due to a prolonged drought, bedding had a larger effect on WWH sites than DWH harvested sites. The effects of droughty conditions may be influencing treatment response on these highly productive sites; however, the long-term effects of harvesting on stand growth remain to be seen.     

Partial characterization of the exopolysaccharide from Oscillatoria trichoides Szafer and the role of released polysaccharide in sequestration of Cr6+

The structural investigation and the chromium adsorptive potential of an exopolysaccharide (EPS) released during the growth of an indigenous cyanobacterium, Oscillatoria trichoides Szafer, were investigated in a laboratory‐scale study. The results showed that, of the total EPS produced, 410.53 milligrams/gram (mg g^?1) were released polysaccharides (RPS) and 11.36 mg g^?1 were capsular polysaccharides (CPS). The sorption of hexavalent chromium (Cr⁶⁺) by the RPS achieved a maximum amount of metal removal (q_max) value of 76.92 mg g^?1 of polysaccharide dry weight. The highest coefficient of determination (0.9742) for the Langmuir adsorption model indicates best fitness of the model in explaining the sorption as a unilayer process. Equilibrium studies indicated that 30 to 40 milligrams per liter initial chromium concentration and a pH of 2 were optimal for biosorption of chromium by the RPS. Scanning electron microscopy with energy‐dispersive X‐ray spectroscopy analysis of Cr⁶⁺‐treated RPS showed the presence of 3.76% bound chromium. Compositional analysis of the EPS showed the presence of carbohydrates, proteins, pyruvic acid, and hexosamines. High‐performance liquid chromatography analysis demonstrated the presence of hexoses, as neutral sugars and glucuronic acid as an acidic sugar. The presence of carboxylic groups was also detected by infrared spectroscopy. The presence of these chemical constituents may serve as binding sites for the metal ions; therefore, the RPS of this species appears to be a promising biosorbent for Cr⁶⁺.     

Effective Removing of Remazol Black B by the Polyacrylamide Cryogels Modified with Polyethyleneimine

In this study, modified polyacrylamide (PAAm) cryogels with high dye holding capacity were synthesized with an easily and cheaply process and adsorption of Remazol Black B (RBB) with the synthesized materials was investigated. Firstly, PAAm cryogels were synthesized with free radical cryo-copolymerization method and they were modified with Hofmann reaction to form amine groups in the structure of the cyrogels. Then, to increase the removal efficiency of cryogels, polyethylenimine (PEI) molecules were crosslinked onto the cryogels via NH₂ groups present in the PAAm gels modified by the Hofmann reaction. The original and modified cryogels were characterized with fourier transformed infrared spectroscopy, ¹³C nuclear magnetic resonance spectroscopy, scanning electron microscopy and thermogravimetric analysis. The point of zero charge (pH_pzc) of the modified cryogels was found to be 7.13 and RBB removing capabilities of PEI-modified PAAm cryogels were investigated at pH between 2 and 7. In addition, the adsorption treatments were performed at different process time, incubation temperature, initial dye concentration and adsorbent amount to find maximum removal capacity of the adsorbent. The modified cryogels adsorbed maximum amount of RBB at pH 2 and the sorption process reached equilibrium in 6 h. It was observed that the adsorption efficiency did not change much with the increase in temperature. The maximum RBB removal capacity of the modified cyrogels was determined to be 201 mg/g when the initial RBB concentration was 200 mg/L, treatment time was 6 h at pH 2. Moreover, the adsorption of RBB dye with the modified cryogels takes place with a second order kinetic and RBB dye adsorption data showed compliance with the Langmuir isotherm. The findings of the study expose that the obtained PEI-modified PAAm cryogels are a hopeful material for RBB removal in aqueous environment.

     

Modified Sugarcane Bagasse with Tartaric Acid for Removal of Diazonium Blue from Aqueous Solutions

The present study concerns with exploring the possibility of using of tartaric acid pretreated sugarcane bagasse (SCB) for removing diazonium blue (DB) from aqueous solutions. The effect of different factors on the efficiency of the adsorbent for the DB dye removal was investigated, including initial dye concentration, contact time, SCB dosage and SCB particle size. Langmuir, Freundlich, Tempkin and D–R isothermal models have been employed to analyze the adsorption equilibrium data. It was found that the adsorption of the dye fits well with the D–R model. The adsorption kinetics was also done applying four kinetic models. The regression equation coefficients refer to fitting the data to the second-order kinetic equation for removal of the DB dye. It is probable that the rate limiting step is a chemical adsorption between the adsorbent and the dye. This chemisorption process is further confirmed from the energy value of 15.1 kJ mol^?1 deduced from the D–R isotherm.     

Adsorption characteristics of Cu2+ and Zn2+ from aqueous solution using carbonized food waste

The aim of the present study was to analytically provide adsorption characteristics of Cu²⁺ and Zn²⁺ using carbonized food waste (CFW); more specifically, batch tests were conducted using various concentrations of metal ions, contact times, and initial pH levels in an attempt to understand the adsorption removal of heavy metal ions in aqueous solution at concentrations ranging between 50 and 800 mg/l. The results confirmed that the adsorption equilibrium was established within a maximum of 80 min, and the maximum concentrations for adsorption of Cu²⁺ and Zn²⁺ were 28.3 and 23.5 mg/g, respectively. These adsorption levels indicate that CFW has better performance than many other adsorbents. In experiments using different pH conditions, the applicability to acid wastewater was found to be high, and an excellent adsorption removal ratio of 75%–90% was observed under acid conditions at pH 2–4. Furthermore, as the adsorption time increased, the calcium component in the CFW began to leach into the aqueous solution and raise the pH, accordingly causing the removal of heavy metal ions partially as a result of precipitation. When our results were analyzed using the Langmuir model and the Freundlich model for isothermal adsorptivity, the activity of CFW in this study was shown to be more consistent with the former; the adsorption speed of Cu²⁺ and Zn²⁺ according to a pseudosecond-order reaction model was found to be very fast for an initial concentration of not more than 100 mg/l. In a test in which an attempt was made to compare adsorption capacity values obtained from the experiments in this study with the aforementioned three models, the pseudosecond-order reaction model was found to provide results closest to the actual values.     

硫酸钙晶须对磷的静态吸附

以磷石膏废渣为原料制备硫酸钙晶须,考察了硫酸钙晶须对模拟含磷废水中磷的去除效果,分析了初始废水pH、初始磷质量浓度、硫酸钙晶须加入量对磷吸附效果的影响,研究了硫酸钙晶须对磷的吸附等温线,同时对吸附机理进行了探讨。实验结果表明：硫酸钙晶须在碱性条件下对磷的去除率较酸性条件下高,且初始废水pH为10时去除效果最佳;最佳硫酸钙晶须加入量为0.03 g/mg（以磷计）;在初始废水pH为10、初始磷质量浓度为50 mg/L、硫酸钙晶须加入量为1.5 g/L的条件下,于25 ℃下反应1 h,磷的去除率达到99.16%,上清液TP为0.419 mg/L;与Freundlich模型相比,Langmuir等温吸附模型更适合描述硫酸钙晶须对磷的吸附过程,采用该模型拟合得出25 ℃下磷的饱和吸附量为140.4 mg/g。     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.