Adsorption and desorption characteristics of hydrophobic pesticide endosulfan in four Indian soils

Adsorption and desorption characteristics of endosulfan in four Indian soils were studied extensively. The soils used were clayey soil (CL--lean clay with sand), red soil (GM--silty gravel with sand), sandy soil (SM--silty sand with gravel) and composted soil (PT--peat) as per ASTM (American Society for Testing and Materials) standards. Adsorption and desorption rates were calculated from kinetic studies. These values varied for alpha and beta endosulfan depending on the soil type. Maximum specific adsorption capacities (qmax) for different soils were calculated by Langmuir model. The values varied from 0.1 to 0.45 mg g(-1) for alpha endosulfan and 0.0942-0.2722 mg g(-1) for beta endosulfan. Maximum adsorption took place in clay soil followed by composted soil and red soil. Adsorptions of alpha and beta endosulfan were negligible in sand. The binding characteristics of various functional groups were calculated using Scatchard plot. Effect of functional groups was more predominant in clayey soil. Organic matter also played a significant role in adsorption and desorption of endosulfan. Endosulfan adsorption decreased drastically in clay soil when the pH was reduced. Desorption was higher at both acidic and alkaline pH ranges compared to neutral pH. Results indicated that alpha endosulfan is more mobile compared to beta endosulfan and mobility of endosulfan is maximum in sandy soil followed by red soil. It can be inferred that crystal lattice of the clay soil plays a significant role in endosulfan adsorption and desorption. Immobilization of endosulfan is more advisable in clay soil whereas biological and or chemical process can be applied effectively for the remediation of other soil types.     

Estimates of ambient background concentrations of trace metals in soils for risk assessment

Site-specific or soil type-specific ambient background concentrations (ABCs) of trace metals in soils are needed for risk assessment. We investigated three different methods for estimating ABCs in soils using a dataset of 5691 soil samples from England and Wales. The concentrations of Co, Cr and Ni were strongly associated with Al and Fe, and multiple regressions explained 62-85% of their variation, and Al and Fe can therefore be used to predict ABCs for these metals. Soil texture had a major influence on the concentrations of Cd, Co, Cr, Cu, Ni and Zn, and the medians were 3-5 fold higher in clayey than in sandy soils. This was used to predict texture-specific ABCs. Lead concentration was higher in acidic peaty soils than in other soils. A probability graph method was used to estimate ABC for Pb in a population of relatively uncontaminated soils. Potential applications of ABCs are discussed.     

Effects of metals on life cycle parameters of the earthworm Eisenia fetida exposed to field-contaminated, metal-polluted soils

Two control and eight field-contaminated, metal-polluted soils were inoculated with Eisenia fetida (Savigny, 1826). Three, 7, 14, 21, 28 and 42 days after inoculation, earthworm survival, body weight, cocoon production and hatching rate were measured. Seventeen metals were analysed in E. fetida tissue, bulk soil and soil solution. Soil organic carbon content, texture, pH and cation exchange capacity were also measured. Cocoon production and hatching rate were more sensitive to adverse conditions than survival or weight change. Soil properties other than metal concentration impacted toxicity. The most toxic soils were organic-poor (1-10 g C kg(-1)), sandy soils (c. 74% sand), with intermediate metal concentrations (e.g. 7150-13,100 mg Pb kg(-1), 2970-53,400 mg Zn kg(-1)). Significant relationships between soil properties and the life cycle parameters were determined. The best coefficients of correlation were generally found for texture, pH, Ag, Cd, Mg, Pb, Tl, and Zn both singularly and in multivariate regressions. Studies that use metal-amended artificial soils are not useful to predict toxicity of field multi-contaminated soils.     

Phosphorus leaching in soils amended with piggery effluent or lime residues from effluent treatment

Phosphorus (P) in wastes from piggeries may contribute to the eutrophication of waterways if not disposed of appropriately. Phosphorus leaching, from three soils with different P sorption characteristics (two with low P retention and one with moderate P retention) when treated with piggery effluent (with or without struvite), was investigated using batch and leaching experiments. The leaching of P retained in soil from the application of struvite effluent was determined. In addition, P leaching from lime residues (resulting from the treatment of piggery effluent with lime to remove P) was determined in comparison to superphosphate when applied to the same three soils. Most P was leached from sandy soils with low P retention when effluent with or without struvite was applied. More than 100% of the filterable P applied in struvite effluent was leached in sandy soils with low P retention. Solid, inorganic forms of P (struvite) became soluble and potentially leachable at pH<7 or were sorbed after dissolution if there were sufficient sorption sites. In sandy soils with low P retention, more than 39% of the total filterable P applied in recycled effluent (without struvite) was leached. Soil P increased mainly in surface layers after treatment with effluent. Sandy soils pre-treated with struvite effluent leached 40% of the P retained in the previous application. Phosphorus decreased in surface layers and increased at depth in the soil with moderate P retention after leaching the struvite effluent pre-treated soil with water. The soils capacity to adsorb P and the soil pH were the major soil properties that affected the rate and amount of P leaching, whereas the important characteristics of the effluent were pH, P concentration and the forms of P in the effluent. Phosphorus losses from soils amended with hydrated lime and lime kiln dust residues were much lower than losses from soils amended with superphosphate. Up to 92% of the P applied as superphosphate was leached from sandy soils with low P retention, whereas only up to 60% of the P applied in lime residues was leached. The P source contributing least to P leaching was the lime kiln dust residue. The amount of P leached depended on the water-soluble P content, neutralising value and application rate of the P source, and the pH and P sorption capacity of the soil.     

Clay charge reversal effects on aqueous polymer sorption on lateritic soils

The effects of charge reversal about the measured point of zero charge (pH(0) approximately 5.2) of untreated and treated Sete Lagoas lateritic soil of Brazil on aqueous polymer sorption was investigated. The polymers are anionic sodium carboxymethyl cellulose (CMCA), nonionic polyethylene oxide (PEO), and cationic polyacrylamide (PAM). They were prepared at aqueous concentrations and pH ranges of 0.1-2.0 g l(-1) and 2-9, respectively. Soil treatment involved the removal of iron oxides by treatment with dithionate-bicarbonate-citrate. Batch sorption test results show that the presence of iron oxides in lateritic soil tends to suppress sorption of CMCA (especially at pH=pH(0)) and PEO (for the whole pH range) but has uncertain effects on cationic PAM sorption. CMCA sorption on the untreated soil improves on either side of pH(0), in direct proportionality to solution concentration, except at pH<4.0, where disassociation of the polymer molecules may decrease sorption energy. Increase in the sorption of non-cationic polymers (CMCA and PEO) at pH>pH(0) is attributable to dispersion of clay, cation bridging and polymer molecular reconfiguration. For cationic PAM, electrostatic bonding to negatively charged soil particle surfaces accounts for the sorption increase. For treated soil samples, polymer sorption pattern is similar to those expected for the montmorillonitic clayey soils of temperate zones. These results indicate that the pH(0) of lateritic soils, within the regime that exists in the field, should be considered in assessing the potential effectiveness of polymer dust suppressants for tropical lateritic soils.     

Cadmium availability to wheat grain in soils treated with sewage sludge or metal salts

Grain Cd concentrations were determined in wheat (Triticum aestivum L.) grown in 1999, 2001 and 2003, at six sludge cake field experiments. Three of these sites also had comparisons with Cd availability from metal amended liquid sludge and metal salts. Grain Cd concentrations in all years and at all sites were significantly linearly correlated with NH4NO3 extractable Cd and soil total Cd (P<0.001). Soil extractability was greater in the liquid sludge and metal salt experiments than in the cake experiments, as were grain Cd concentrations. Across all the sites, NH4NO3 extractable soil Cd was no better at predicting grain Cd than soil total Cd. Stepwise multiple linear regression analysis showed that soil total Cd, pH and organic carbon were the only significant (P<0.001) variables influencing wheat grain Cd concentrations, explaining 78% of the variance across all field experiments (1408 plots). This regression predicted that the current UK soil total Cd limit of 3 mg kg(-1) was not sufficiently protective against producing grain above the European Union (EU) grain Cd Maximum Permissible Concentration (MPC) of 0.235 mg Cd kg(-1) dry weight, unless the soil pH was > 6.8. Our predictions show that grain would be below the MPC with > 95% confidence with the proposed new EU draft regulations permitting maximum total Cd concentrations in soils receiving sludge of 0.5 mg kg(-1) for soils of pH 5-6, 1 mg kg(-1) for soils of pH 6-7, and 1.5 mg kg(-1) for soils of pH > or = 7.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48-72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K(d)) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Potentials and drawbacks of chelate-enhanced phytoremediation of soils.

Chelate-enhanced phytoremediation has been proposed as an effective tool for the extraction of heavy metals from soils by plants. However, side-effects related to the addition of chelates, e.g. metal leaching and effects on soil micro-organisms, were usually neglected. Therefore, greenhouse and lysimeter studies were conducted to study the phytoremedation potential of EDGA and citric acid and to evaluate its effects on microbial activity and leaching of Cd, Zn Cu and Pb. Grass, lupine and yellow mustard were grown on a moderately polluted acid (pH 4.5) sandy soil that contained 2 mg kg(-1) Cd and 200 mg kg(-1) Zn. Citric acid appeared to be degraded microbially within a few days after addition which limited its potential for long-lasting remediation studies. EDGA enhanced metal solubility but plant uptake did not increase accordingly. The metal shoot:root ratio increased upon addition of EDGA but it also reduced the net shoot and root biomass production of both lupine and yellow mustard. Bacterial biomass was higher in both the citric and EDGA treated pots but bacterial activity remained unaffected. The number of microbivorous nematodes was greatly reduced upon addition of EDGA which was most likely related to the reduced biomass production and, to a smaller extent, to the changes in the composition of the available food. Furthermore, EDGA enhanced metal leaching in the lysimeter study which could lead to groundwater pollution. To prevent these unwanted side-effects, careful management of phytoremediation methods, therefore, seems necessary.     

Mobility of aniline, benzoic acid, and toluene in four soils and correlation with soil properties

Soil properties and retention mechanisms affecting the relative mobility of aniline, benzoic acid, and toluene in Cecil sandy loam (clayey, kaolinitic, thermic Typic Hapludults), Holdredge silt loam (fine-silty, mixed, mesic Typic Argiustolls), Sharpsburg silty clay loam (fine, montmorillonitic, mesic Typic Argiudolls), and Valentine fine sand (mixed, mesic Typic Ustipsamments) were delineated in laboratory studies. The effect of the synthetic organic compounds (SOCs) was also determined on effective organic campounds (SOCs) was also determined on effective cation exchange capacity (ECEC) of the soils. Benzoic acid was most mobile of the SOCs but was retained in the Cecil soil by hydrogen bonds to Fe oxides. Toluene was least mobile and probably was hydrophobically sorbed to all soils. Aniline was electrostatically retained in protonated form to organic and inorganic exchange sites of the soils and reduced the ECEC of aniline-treated Holdredge and Sharpsburg soils.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48–72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K _d) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Influence of cadmium on carbon and nitrogen mineralization in sewage sludge amended soils

The effect of cadmium on C and N mineralization in sewage sludge amended and unamended sandy loam, loam and clay loam soils was studied during 2 months incubation at 30+/-1 degrees C. The sludge amendment caused 15-39% increase in microbial respiration, with the maximum C mineralization in sandy loam and the minimum in loam soil. The addition of 10 microg Cd g(-1) soil had no remarkable effect on C and N mineralization and microbial biomass; whereas significant decreases in the above parameters were observed at 25 and 50 microg Cd g(-1) soil, irrespective of the sludge addition. Less NO3(-)-N accumulated at higher Cd concentration. Cd recovery was high in sandy loam and low in clay loam soil. DTPA extractable Cd exhibited a significant negative correlation with microbial biomass (r=-0.58* to -0.86*; p < 0.05).     

Growth and physiological responses of Pennisetum sp. to cadmium stress under three different soils

Pennisetum sp. was employed as a model species to detect the growth and physiological response to cadmium (Cd) stress at different Cd concentrations (0, 20, 50, and 100 mg kg⁻¹) in three types of soils (yellow brown soil, yellow soil, and red soil). Results showed that the growth of Pennisetum sp. was not significantly influenced by Cd in 20 mg kg⁻¹, but significantly inhibited at higher Cd concentrations in three types of soils. Besides, the higher Cd concentrations, the lower root, stem, and leaf biomass. With Cd concentration of soil increasing, Cd content of root, stem, and leaf increased. Compared with no Cd, high Cd concentrations (50 and 100 mg kg⁻¹) induced the physiological indices (photosynthetic rate, stomatal conductance, transpiration rate) and biochemical indices (nitrate reductase, glutamine synthetase, and glutamate synthase activities) decreasing, but the concentration of NO₃⁻ and NH₄⁺ increasing. The activity of antioxidative enzymes (SOD, POD, and CAT) was disrupted and the content of malondialdehyde (MDA) increasing. Pennisetum sp. could protect cells from damage and maintain normal physiological metabolism via increasing the production of soluble sugar and soluble protein, but soluble proteins and soluble sugars were limited in high concentrations of Cd (50 and 100 mg kg⁻¹). Moreover, the growth and physiological response to Cd are different in the three types of soils. The growth of Pennisetum sp. in yellow brown soil was better than that in other two soils, and the gas exchange rate, antioxidant enzyme activity, and nitrogen metabolism in yellow soil and red soil were more affected by Cd stress than that in yellow brown soil. Overall, Pennisetum sp. had certain tolerance and biosorption ability to Cd in different Cd concentrations and different types of soil. Hence, Pennisetum sp. was a suitable choice for Cd remediation, especially in yellow brown soil.

     

Biosurfactant technology for remediation of cadmium and lead contaminated soils

This research focuses on column experiments conducted to evaluate the potential of environmentally compatible rhamnolipid biosurfactant produced by Pseudomonas aeruginosa strain BS2 to remove heavy metals (Cd and Pb) from artificially contaminated soil. Results have shown that di-rhamnolipid removes not only the leachable or available fraction of Cd and Pb but also the bound metals as compared to tap water which removed the mobile fraction only. Washing of contaminated soil with tap water revealed that approximately 2.7% of Cd and 9.8% of Pb in contaminated soil was in freely available or weakly bound forms whereas washing with rhamnolipid removed 92% of Cd and 88% of Pb after 36 h of leaching. This indicated that di-rhamnolipid selectively favours mobilization of metals in the order of Cd>Pb. Biosurfactant specificity observed towards specific metal will help in preferential elution of specific contaminant using di-rhamnolipid. It was further observed that pH of the leachates collected from heavy metal contaminated soil column treated with di-rhamnolipid solution was low (6.60-6.78) as compared to that of leachates from heavy metal contaminated soil column treated with tap water (pH 6.90-7.25), which showed high dissolution of metal species from the contaminated soil and effective leaching of metals with treatment with biosurfactant. The microbial population of the contaminated soil was increased after removal of metals by biosurfactant indicating the decrease of toxicity of metals to soil microflora. This study shows that biosurfactant technology can be an effective and nondestructive method for bioremediation of cadmium and lead contaminated soil.     

Column- and catchment-scale transport of cadmium: effect of dissolved organic matter

In the Ellen catchment on the Pinjarra Plain, NE of Perth in Western Australia, cadmium from fertilisers is starting to leach from soils. About 70% of surface soils in the Ellen catchment are sandy and often on top of a shallow ephemeral water table. Adsorption of Cd in the sandy soils of the Ellen catchment was studied by batch adsorption and by leaching small columns of soil. Adsorption of Cd increases linearly with increasing soil organic matter content and exponentially with increasing pH. Cadmium is significantly mobilised in the sandy soils by dissolved organic matter.The capacity of most of the sandy soils in the Ellen catchment to adsorb phosphate from fertiliser has been saturated. Resulting concentrations in Ellen Brook average 500 μg L⁻¹ P. Cadmium is adsorbed more strongly in the sandy soils than phosphate and is just starting to leach into Ellen Brook. From a comparison of Cd/P ratios in water, soils and fertiliser, cadmium concentrations in Ellen Brook are estimated to be at 10–30% of their maximum for complete breakthrough from soils. Present concentrations of Cd in Ellen Brook average 0.1 μg L⁻¹ and are estimated to approach the maximum for complete breakthrough in 100 yr. Maximum Cd concentrations in Ellen Brook could range from 0.6 to 2 μg L⁻¹, depending on rates of input with fertiliser and future increases in agricultural land use in the catchment.Breakthrough curves, resulting from leaching Cd through small columns of sandy soil, indicate that adsorption significantly increases the effective hydrodynamic dispersion of Cd. Longitudinal dispersivities, measured at pore-water velocities of 0.7–14 m day⁻¹, were 5 cm for Cd and 0.1–0.2 cm for chloride. The much greater dispersion of Cd in the sandy soils than of chloride is shown not to be caused by non-equilibrium adsorption.     

Remediation of cadmium contamination in paddy soils by washing with chemicals: selection of washing chemicals

The efficiencies of neutral salts, strong acids, and chelates were tested for extracting cadmium (Cd) from three paddy soils. The higher the selectivity of the cations of the added neutral salts toward soil adsorption sites, the lower the pH in the extracts and the more soil Cd could be extracted. In addition, soil carbon and nitrogen contents and mineral composition were closely associated with the amount of Cd extracted. Calcium chloride and iron(III) chloride were selected as wash chemicals to restore Cd-contaminated paddy soils in situ. Washing with calcium chloride led to the formation of Cd chloride complexes, enhancing Cd extraction from the soils. The washing also substantially decreased soil levels of exchangeable and acid-soluble Cd, which are the major forms of bioavailable Cd for rice (Oryza sativa L.). The optimum conditions for in situ soil washing were also determined for calcium chloride.     

Use of sequential extraction to assess metal partitioning in soils

The state of heavy metal pollution and the mobility of Cd, Cu, Ni, Cr, Pb and Zn were studied in three texturally different agricultural soil profiles near a Cu-Ni smelter in Harjavalta, Finland. The pseudo-total concentrations were determined by an aqua regia procedure. Metals were also determined after division into four fractions by sequential extraction with (1) acetic acid (exchangeable and specifically adsorbed metals), (2) a reducing agent (bound to Fe/Mn hydroxides), (3) an oxidizing agent (bound to soil organic matter) and (4) aqua regia (bound to mineral structures). Fallout from the smelter has increased the concentrations of Cd, Cu and Ni in the topsoil, where 75-90% of Cd, 49-72% of Cu and 22-52% of Ni occurred in the first two fractions. Slight Pb and Zn pollution was evident as well. High proportions of mobile Cd, Cu and Ni also deeper in the sandy soil, closest to the smelter, indicated some downward movement of metals. The hydroxide-bound fraction of Pb dominated in almost all soils and horizons, while Ni, Cr and Zn mostly occurred in mineral structures. Aqua regia extraction is usefully supplemented with sequential extraction, particularly in less polluted soils and in soils that exhibit substantial textural differences within the profiles.     

Application of magnetite-activated persulfate oxidation for the degradation of PAHs in contaminated soils

In this study, feasibility of magnetite-activated persulfate oxidation (AP) was evaluated for the degradation of polycyclic aromatic hydrocarbons (PAHs) in batch slurry system. Persulfate oxidation activated with soluble Fe(II) (FP) or without activation (SP) was also tested. Kinetic oxidation of PAHs was tracked in spiked sand and in aged PAH contaminated soils at circumneutral pH. Quartz sand was spiked with: (i) single model pollutant (fluorenone) and (ii) organic extract isolated from two PAH contaminated soils (H and NM sampled from ancient coking plants) and was subjected to oxidation. Oxidation was also performed on real H and NM soils with and without an extraction pretreatment. Results indicate that oxidation of fluorenone resulted in its complete degradation by AP while abatement was very low (<20%) by SP or FP. In soil extracts spiked on sand, significant degradation of 16 PAHs was observed by AP (70-80%) in 1 week as compared to only 15% by SP or FP systems. But no PAH abatement was observed in real soils whatever the treatment used (AP, FP or SP). Then soils were subjected to an extraction pretreatment but without isolation of organic extract from soil. Oxidation of this pretreated soil showed significant abatement of PAHs by AP. On the other hand, very low degradation was achieved by FP or SP. Selective degradation of PAHs was observed by AP with lower degradation efficiency towards high molecular weight PAHs. Analyses revealed that no by-products were formed during oxidation. The results of this study demonstrate that magnetite can activate persulfate at circumneutral pH for an effective degradation of PAHs in soils. However, availability of PAHs and soil matrix were found to be the most critical factors for degradation efficiency.     

Mobilization of phenol and dichlorophenol in unsaturated soils by non-uniform electrokinetics

The poor mobility of organic pollutants in contaminated sites frequently results in slow remediation processes. Organics, especially hydrophobic compounds, are generally retained strongly in soil matrix as a result of sorption, sequestration, or even formation into non-aqueous-phase liquids and their mobility is thus greatly reduced. The objective of this study was to evaluate the feasibility of using non-uniform electrokinetic transport processes to enhance the mobility of organic pollutants in unsaturated soils with no injection reagents. Phenol and 2,4-dichlorophenol (2,4-DCP), and kaolin and a natural sandy loam soil were selected as model organics and soils, respectively. The results showed that non-uniform electrokinetics can accelerate the desorption and movement of phenol and 2,4-DCP in unsaturated soils. Electromigration and electroosmotic flow were the main driving forces, and their role in the mobilization of phenol and 2,4-DCP varied with soil pH. The movement of 2,4-DCP in the sandy loam towards the anode (about 1.0 cmd(-1)V(-1)) was 1.0-1.5 cmd(-1)V(-1) slower than that in the kaolin soil, but about 0.5 cmd(-1)V(-1) greater than that of phenol in the sandy loam. When the sandy loam was adjusted to pH 9.3, the movement of phenol and 2,4-DCP towards the anode was about twice and five times faster than that at pH 7.7, respectively. The results also demonstrated that the movement of phenol and 2,4-DCP in soils can be easily controlled by regulating the operational mode of electric field. It is believed that non-uniform electrokinetics has the potential for practical application to in situ remediation of organics-contaminated sites.     

Trace metal speciation and bioavailability in urban soils

Urban soils often contain concentrations of trace metals that exceed regulatory levels. However, the threat posed by trace metals to human health and the environment is thought to be dependent on their speciation in the soil solution rather than the total concentration. Three inactive railway yards in Montréal, Québec, were sampled to investigate the speciation and bioavailability of Cd, Cu, Ni, Pb and Zn. Soil solutions were obtained by centrifuging saturated soil pastes. In the soil solutions, up to 59% of the dissolved Cd was in its free ionic form. For Cu, Pb and Zn, organic complexes were the predominant species. Over 40% of Ni was present as inorganic complexes if the solution pH exceeded 8.1. Multiple regression analyses showed that pH and total metals in soil were significantly correlated with the activities of free metal ions, except for Cd(2+), which only had a weak correlation with soil pH. Free, dissolved and total soil metals were tested for their ability to predict metal uptake by plants in the field. However, none of these metal pools were satisfactory predictors. The results indicated that in these urban soils, trace metals were mainly in stable forms and bioavailability was extremely low.     

The role of dissolved organic carbon in the mobility of Cd, Ni and Zn in sewage sludge-amended soils

A pot experiment was conducted to investigate the effect of application of naturally derived dissolved organic compounds (DOC) on the uptake of Cd, Ni and Zn by Lolium perenne L. from mixtures of soil and sewage sludge and on their extractability with CaCl2. DOC was applied at concentrations of 0, 285 and 470 mg l(-1) to a loamy sand (LS) and a sandy clay loam (SCL) soil mixed with sewage sludge at rates equivalent to 0, 10 and 50 t ha(-1). DOC applications significantly increased the extractability of metals and also their uptake by ryegrass, but the increase was greater where sludge was applied at 50 t ha(-1). It is suggested that DOC in soils significantly increased the availability of the metals to plants. This was especially the case in the LS soil, where DOC had less competition with surface sorption than in the SCL soil.