New large solar photocatalytic plant: set-up and preliminary results

A European industrial consortium called SOLARDETOX has been created as the result of an EC-DGXII BRITE-EURAM-III-financed project on solar photocatalytic detoxification of water. The project objective was to develop a simple, efficient and commercially competitive water-treatment technology, based on compound parabolic collectors (CPCs) solar collectors and TiO2 photocatalysis, to make possible easy design and installation. The design, set-up and preliminary results of the main project deliverable, the first European industrial solar detoxification treatment plant, is presented. This plant has been designed for the batch treatment of 2 m3 of water with a 100 m2 collector-aperture area and aqueous aerated suspensions of polycrystalline TiO2 irradiated by sunlight. Fully automatic control reduces operation and maintenance manpower. Plant behaviour has been compared (using dichloroacetic acid and cyanide at 50 mg l(-1) initial concentration as model compounds) with the small CPC pilot plants installed at the Plataforma Solar de Almería several years ago. The first results with high-content cyanide (1 g l(-1)) waste water are presented and plant treatment capacity is calculated.     

Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

Photocatalysis for arsenic removal from water: considerations for solar photocatalytic reactors

Environmental Science and Pollution Research - The following work provides a perspective on the potential application of solar heterogeneous photocatalysis, which is a nonselective advanced...     

Easy-handling semi-floating TiO2-based aerogel for solar photocatalytic water depollution

Environmental Science and Pollution Research - One of the capital issues of photocatalytic technology is how to use photocatalytic materials in real world conditions. Suspension photocatalysts are...     

Heterogeneous photocatalytic oxidation of cyprodinil and fludioxonil in leaching water under solar irradiation

The efficiency of ZnO and TiO₂ suspensions in the photocatalytic degradation of two fungicides (cyprodinil and fludioxonil) in leaching water was investigated. The experiments were carried out at pilot plant scale using compound parabolic collectors under natural sunlight. The blank experiments for both irradiated compounds solutions showed that both oxides strongly enhanced the removal of the fungicides. The addition of an oxidant (Na₂S₂O₈) to the ZnO or TiO₂ increased the rate of photooxidation. The degradation of cyprodinil and fludioxonil followed first order kinetics according to the Langmuir-Hinshelwood model. Complete degradation of both fungicides was achieved within 4 h (t_30W = 18 min) when treated with illuminated ZnO. The disappearance time (DT₇₅), when referred to the normalized illumination time (t_30W), was lower than 40 and 550 min (t_30W = 2 and 40 min) for both fungicides using ZnO or TiO₂, respectively. ZnO appeared to be more effective in cyprodinil and fludioxonil oxidation than TiO₂ probably due to its nonstoichiometry.     

Degradation of carbofuran in water by solar photocatalysis in presence of photosensitizers

The effect of the presence of photosensitizers, methylene blue (MB) and rose Bengal (RB), on the degradation of carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) in water in a solar photocatalytic system was investigated. It was found that as compared to MB, RB generally showed a stronger effect on the decomposition of carbofuran under comparable conditions. Among the conditions studied, adding 2 x 10(-6) M of RB, that corresponding to 2% of the initial concentration of carbofuran solution in the system, rendered the most effective degradation of carbofuran. As a result, a carbofuran removal percentage of 69.9%, a mineralization efficiency of 28.0%, and a microtoxicity reduction of 65.0% could be achieved. The degradation and mineralization of carbofuran was found to follow the pseudo-first order reaction kinetics. The decomposition mechanism of carbofuran was further investigated through identification of the intermediates to elaborate the influence of dye photosensitizer on the solar photocatalysis of carbofuran in water. On the basis of the intermediates identified, including carbofuran phenol, 3-hydroxy carbofuran phenol, and substituted alcohols (3-phenoxy 1-propanol, 2-ethyl 1-hexanol, 2-butoxyl ethanol), it appears that hydrolysis and hydroxylation were the two key mechanisms for decomposing carbofuran during the process of solar photocatalysis with the aid of dye photosensitizer.     

Degradation of pentachlorophenol by pure and mixed cultures in two different soils

GOAL, SCOPE AND BACKGROUND: Pentachlorophenol (PCP) is the second highest volume pesticide used in the United States. It is a mutagenic compound whose exposure poses significant health effects, One of the most desirable, environmentally friendly treatment methods is bioremediation. For soil-based contamination, the effectiveness of bioremediation will also be affected by the presence of an active indigenous population, sorption of the contaminant onto the soil, and environmental parameters. METHODS: Two pure strains and their mixed culture were used to evaluate PCP biodegradation in two different field soils, Columbia (CO) and New Mexico (NM). Biostimulation of the indigenous microbes was evaluated by adding nutrients. The efficiency of adding bacteria strains (bioaugmentation) for degrading PCP was determined with Arthrobacter sp., Flavobacterium sp. and a 50:50 mixture of the two bacteria strains. RESULTS: In CO soil, only 24%, 12% and 25% of the initial PCP concentration were degraded by Flavobacterium sp., Arthrobacter sp. and mixed culture, respectively. Arthrobacter sp. was used in NM soil with two initial concentrations and achieved degradation efficiencies of 57% and 61% for 361 and 95 mg kg- concentrations, respectively. Discussion. Analysis via statistical methods showed that the bacteria had different efficiencies on PCP degradation in each soil. 2 CONCLUSIONS: All bacteria catalyzed a higher PCP degradation when present in NM soil. Second, Flavobacterium sp. degraded more PCP than Arthrobacter sp. in CO soil. The mixed culture achieved the highest degradation efficiency regardless of the initial concentration or soil origin. RECOMMENDATIONS AND PERSPECTIVES: The effect of the soil properties, such as the soil organic matter (SOM) on PCP biodegradation should be investigated. Future work can also investigate the effect of aging time on biodegradation.     

Nanomaterials photocatalytic activities for waste water treatment: a review

Water is necessary for the survival of life on Earth. A wide range of pollutants has contaminated water resources in the last few decades. The presence of contaminants incredibly different dyes in waste, potable, and surface water is hazardous to environmental and human health. Different types of dyes are the principal contaminants in water that need sudden attention because of their widespread domestic and industrial use. The toxic effects of these dyes and their ability to resist traditional water treatment procedures have inspired the researcher to develop an eco-friendly method that could effectively and efficiently degrade these toxic contaminants. Here, in this review, we explored the effective and economical methods of metal-based nanomaterials photocatalytic degradation for successfully removing dyes from wastewater. This study provides a tool for protecting the environment and human health. In addition, the insights into the transformation of solar energy for photocatalytic reduction of toxic metal ions and photocatalytic degradation of dyes contaminated wastewater will open a gate for water treatment research. The mechanism of photocatalytic degradation and the parameters that affect the photocatalytic activities of various photocatalysts have also been reported.

     

Degradation of some biorecalcitrant pesticides by homogeneous and heterogeneous photocatalytic ozonation

Photo-Fenton/ozone (PhFO) and TiO2-photocatalysis/ozone (PhCO) coupled systems are used as advanced oxidation processes for the degradation of the following biorecalcitrant pesticides: alachlor, atrazine, chlorfenvinfos, diuron, isoproturon and pentachlorophenol. These organic compounds are considered Priority Hazardous Substances by the Water Framework Directive of the European Commission. The degradation process of the different pesticides, that occurs through oxidation of the organic molecules by means of their reaction with generated OH radical, follows a first and zero-order kinetics, when PhFO and PhCO are applied, respectively. These two Advanced Oxidation Processes, together with the traditional ozone+UV, have been used to investigate TOC reduction of the different pesticide aqueous solutions. The best results of pesticide mineralization are obtained when PhFO is applied; with the use of this advanced oxidation process the aqueous pesticide solutions become detoxyfied except in the case of atrazine and alachlor aqueous solutions for which no detoxification is achieved at the experimental conditions used in the work, at least after 2 and 3 h of treatment, respectively.     

Solar photocatalytic decolorization of methylene blue in water

In this study, a photocatalytic decolorization system equipped with immobilized TiO2 and illuminated by solar light was used to remove the color of wastewater. To examine the decoloring efficiency of this system, photocatalytic decolorization of an organic dye such as methylene blue was studied as an example. The effects of light source, pH, as well as the initial concentration of dye were also investigated. It was observed that the solution of methylene blue could be almost completely decolorized by the solar light/TiO2 film process while there was about 50% color remaining with solar irradiation only. In addition, it was found that the decoloring efficiency of solution was higher with solar light irradiation than with artificial UV light irradiation, even though the artificial UV light source supplied higher UV intensity at 254 nm. The color removal rate of methylene blue with solar light irradiation was almost twice that of artificial UV light irradiation. This phenomena was mainly attributed to that some visible light range of solar light was useful for exciting the methylene blue molecules adsorbed on TiO2 film, leading to a photosensitization process undergoing and decoloring efficiency promoted. This solar-assisted photocatalytic device showed potential application for decoloring organic dyes in wastewater.     

TiO2光催化降解低浓度溴氰菊酯

用高压汞灯为光源,以二氧化钛光催化降解有机溴杀虫剂－溴氰菊酯,研究了ＴｉＯ２用量、ＰＨ值、等对降解的影响及采用太阳光做光源处理溴氰菊酯的可行性。说明以高压汞灯及太阳光作光源,ＴｉＯ２催化降解敌杀死是有效的。     

Degradation of azo dye Procion Red MX-5B by photocatalytic oxidation

The photocatalytic oxidation (PCO) of a monoazo dye Procion Red MX-5B under various physico-chemical conditions was investigated. Degradation of the dye by PCO was enhanced by augmentation in UV intensity, titanium dioxide and hydrogen peroxide concentrations but was inhibited by increase in initial dye concentration. The PCO process was affected by pH in a peculiar way. In the presence of 100 mg/l of TiO2 and the absence of H2O2, the highest reaction rate was observed when the initial pH was 10. With 500 mg/l of TiO2 and 10 mM of H2O2, the reaction was the fastest at initial pH of 3-5. The optimal conditions for the degradation of the dye, at an UV intensity of 17 mW/cm2, were determined to be: TiO2 concentration, 500 mg/l; initial H2O2 concentration, 10 mM; initial pH, 5.0. Monitoring of TOC loss showed that the dye was mineralized by 90% within 80 min under these conditions. Nevertheless, the persistence of a low level of TOC indicated that mineralization was not complete and dead-end product(s) which was (were) resistant to PCO might have accumulated.     

Azo-dyes photocatalytic degradation in aqueous suspension of TiO2 under solar irradiation

The photodegradation of two common and very stable azo-dyes, i.e. methyl-orange (C₁₄H₁₄N₃SO₃Na) and orange II (C₁₆H₁₁N₂SO₄Na), is reported. The photocatalytic oxidation was carried out in aqueous suspensions of polycrystalline TiO₂ irradiated by sunlight. Compound parabolic collectors, installed at the “Plataforma Solar de Almería” (PSA, Spain) were used as the photoreactors and two identical reacting systems allowed to perform photoreactivity runs for the two dyes at the same time and under the same irradiation conditions. The disappearance of colour and substrates together with the abatement of total organic carbon content was monitored. The main sulfonate-containing intermediates were found to be in lower number in respect to those obtained under artificial irradiation. In particular there were no more evidence of the presence of hydroxylated transients. The dependence of dye photooxidation rate on: (i) substrate concentration; (ii) catalyst amount; and (iii) initial pH was investigated. The influence of the presence of strong oxidant species (H₂O₂, S₂O₈²⁻) and some ions (Cl⁻, SO₄²⁻) on the process was also studied.     

Degradation of atrazine using solar driven fenton-like advanced oxidation processes

Atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine) was degraded using cobalt-peroximonosulfate (Co/PMS) advanced oxidation process (AOP). Three Co concentrations (0.00, 0.25 and 0.50 mM) and five peroximonosulfate (PMS) concentrations (0, 5, 8, 16 and 32 mM) were tested. Maximum degradation reached was 88% using dark Co/PMS in 126 minutes when 0.25 mM of cobalt and 32 mM of PMS were used. Complete atrazine degradation was achieved when the samples were irradiated by the sun under the same experimental conditions described. Tests for identification of intermediate products allowed identification and quantification of deethylatrazine in both dark and radiated conditions. Kinetic data for both processes was calculated fitting a pseudo-first order reaction rate approach to the experimental data. Having kinetic parameters enabled comparison between both conditions. It was found that the kinetic approach describes data behavior appropriately (R² ≥ 0.95). Pseudo-kinetic constants determined for both Co/PMS processes, show k value of 10^?4 for Co/PMS and a k value of 10^?3 for Co/PMS/ultraviolet (UV). This means, that, with the same Co/PMS concentrations, UV light increases the reaction rate by around one order of magnitude than performing the reaction under dark conditions.     

Degradation of atrazine using solar driven fenton-like advanced oxidation processes

Atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine) was degraded using cobalt-peroximonosulfate (Co/PMS) advanced oxidation process (AOP). Three Co concentrations (0.00, 0.25 and 0.50 mM) and five peroximonosulfate (PMS) concentrations (0, 5, 8, 16 and 32 mM) were tested. Maximum degradation reached was 88% using dark Co/PMS in 126 minutes when 0.25 mM of cobalt and 32 mM of PMS were used. Complete atrazine degradation was achieved when the samples were irradiated by the sun under the same experimental conditions described. Tests for identification of intermediate products allowed identification and quantification of deethylatrazine in both dark and radiated conditions. Kinetic data for both processes was calculated fitting a pseudo-first order reaction rate approach to the experimental data. Having kinetic parameters enabled comparison between both conditions. It was found that the kinetic approach describes data behavior appropriately (R2 > or = 0.95). Pseudo-kinetic constants determined for both Co/PMS processes, show k value of 10(-4) for Co/PMS and a k value of 10(-3) for Co/PMS/ultraviolet (UV). This means, that, with the same Co/PMS concentrations, UV light increases the reaction rate by around one order of magnitude than performing the reaction under dark conditions.     

Degradation and toxicity reduction of textile effluent by combined photocatalytic and ozonation processes

To minimize the environmental impact of textile effluents, mainly related to their high coloration and the presence of toxic or carcinogenic reactive dyes, the efficiency of photochemical and ozonation processes, applied in the form of isolated and combined procedures, were evaluated. The investigation was focused on the reduction of total organic carbon content (TOC), color and acute toxicity (monitoring by inhibition of Escherichia coli respiration). For a reaction time of 60 min, the anatase TiO2-assisted photocatalytic process produces color and TOC reduction of about 90% and 50%, respectively. Meanwhile, the ozonation process gives a decolorization of about 60% but negligible TOC reduction. When the processes were applied in a simultaneous form, the decolorization was almost complete and the TOC reduction was higher than 60%. The three treatments studied yield an acute toxicity reduction of around 50%.     

Removal of biocide pentachlorophenol in water system by the spent mushroom compost of Pleurotus pulmonarius

Pentachlorophenol (PCP) has been widely used as a wood preservative since 1980s. Although it has been banned worldwide, residues of PCP are still commonly found. The spent compost of oyster mushroom Pleurotus pulmonarius (SMC) which was a degraded paddy straw-based substrate, contained 25% chitin. Five percentage of the SMC could remove 89.0 +/- 0.4% of 100 mg PCPl(-1) within 2 days at room temperature predominantly by biodegradation. The maximum removal capacity was 15.5 +/- 1.0 mg g(-1) SMC. The sorption kinetics of PCP by SMC can be described by the Freundlich monolayer model with a theoretical sorption capacity similar to that found for chitin. A PCP-degradative bacterium was isolated from the SMC. Yet, biodegradation was predominantly contributed by the immobilized ligninolytic enzymes secreted by the mushroom to the SMC. Degradation of PCP involves dechlorination, methylation, carboxylation and ring cleavage as verified by GC-MSD and ion chromatography. Thus, the SMC has a potential for treating PCP-contaminated water.     

Development of a new approach for microbial decontamination of water using modified Fenton's reaction

Microbial decontamination of water was carried out using a novel radical generating system consisting of ion exchange resin, copper and hydrogen peroxide. The system was successful in reducing the microbial load in water by more than 99% in 15 min and is effective against all the microorganisms tested. The method was also successful in decontaminating the flood water obtained from Industrial Canal and 17th Street Canal in New Orleans. Decontamination is due to the formation of hydroxyl radicals, formed during the decomposition of hydrogen peroxide by the metal-polymer complex.     

Detection of pentachlorophenol and its glucuronide and sulfate conjugates in fish bile and exposure water

The glucuronide and sulfate conjugates of pentachlorophenol (PCP) that were present in the bile and exposure water of goldfish (Carassius auratus) were used to develop methodology to quantify PCP and its metabolites. Reverse phase HPLC with radioactivity detection separated PCP and its metabolites, and was used to verify a method of quantification that used differential extraction and scintillation counting. Extractions of aqueous phase at pH 2 or 8, with butanol, ethyl acetate, or ether indicated that ether at pH 8 best separated PCP from its metabolites. The sulfate conjugate of PCP was the major metabolite produced when goldfish were exposed to 125 micrograms 14C-PCP/l. It was present primarily in the exposure water, but also appeared in the bile.