工业废水污泥的热解及升温速率对热解的影响

利用热重分析法对印染、中药和废水处理厂3种典型工业废水污泥进行了热解动力学实验研究。结果表明,工业污泥是一种高挥发分、低固定碳和低热值的劣质燃料。经过消化处理的污泥灰分含量较高,挥发分含量变小。热解过程中有3个失重速率较高的阶段,以挥发分的析出为主。升温速率对热解的最终失重率有重要影响。升温速率增加,热解更剧烈,但最终失重率的变化趋势与污泥种类有关;为使热解效果更好,不同种类的污泥应选择不同的升温速率。不同种类的污泥具有不同的热解特性,印染污泥挥发分析出阶段有2次热解。中药污泥活化能最小,印染污泥挥发分第2次热解的活化能比第1次大幅增加。     

Effect of textile auxiliaries on the biodegradation of dyehouse effluent in activated sludge

The textile industry is confronted with serious environmental problems associated with its immense wastewater discharge, substantial pollution load, extremely high salinity, and alkaline, heavily coloured effluent. Particular sources of recalcitrance and toxicity in dyehouse effluent are two frequently used textile auxiliaries; i.e. dye carriers and biocidal finishing agents. The present experimental work reports the observation of scientific and practical significance related with the effect of two commercially important textile dye carriers and two biocidal finishing agents on biological activated sludge treatment at a textile preparation, dyeing and finishing plant in Istanbul. Respirometric measurements of the dyehouse effluent spiked with the selected textile chemicals were carried out for the assessment of the "readily biodegradable COD fraction" of the wastewater. The respirometric data obtained to visualize the effect of the selected textile auxiliaries on biomass activity was evaluated by an adopted activated sludge model. Results have indicated that the tested biocides did not exert any significant inhibitory effect on the treatment performance of the activated sludge reactor at the concentrations usually encountered in the final, total dyehouse effluent. The situation with the dye carriers was inherently different; one dye carrier appeared to be highly toxic and caused serious inhibition of the microbial respirometric activity, whereas the other dye carrier, also known as the more ecological alternative, i.e. the "Eco-Carrier", appeared to be biodegradable. Finally, the respirometric profile obtained for the Eco-Carrier was described by a simplified respirometric model.     

生物淋滤-Fenton对印染污泥脱水性能的影响

采用嗜酸性硫杆菌生物淋滤联合Fenton氧化法对印染污泥脱水性能进行了研究。结果表明,生物淋滤过程中pH下降速率随着硫粉添加量增加而变快,经生物淋滤处理后污泥的脱水性能在一定程度上得到了改善。对生物淋滤后的污泥进行了Fenton氧化处理,获得的最佳反应条件为反应时间2h,H2O2和Fe2＋添加量分别为6g／L和0．5g／L。在该条件下,污泥上清液中总有机碳（TOC）由20．8mg／L增加到356．6mg／L;污泥比阻（SRF）和滤饼含水率分别由5．98×10^11s2／g和88．75％减少至1．26×10^11 S2／g和82．85％。生物淋滤-Fenton氧化法在污泥破解程度和脱水性能改善方面均优于单独Fenton氧化法。     

生物淋滤-Fenton对印染污泥脱水性能的影响

采用嗜酸性硫杆菌生物淋滤联合Fenton氧化法对印染污泥脱水性能进行了研究。结果表明,生物淋滤过程中pH下降速率随着硫粉添加量增加而变快,经生物淋滤处理后污泥的脱水性能在一定程度上得到了改善。对生物淋滤后的污泥进行了Fenton氧化处理,获得的最佳反应条件为反应时间2 h,H2O2和Fe2+添加量分别为6 g/L和0.5 g/L。在该条件下,污泥上清液中总有机碳(TOC)由20.8 mg/L增加到356.6 mg/L;污泥比阻(SRF)和滤饼含水率分别由5.98×1011s2/g和88.75%减少至1.26×1011s2/g和82.85%。生物淋滤-Fenton氧化法在污泥破解程度和脱水性能改善方面均优于单独Fenton氧化法。     

抗菌防臭纤维织物杀藻效果研究

针对水华治理需求,采用市售抗菌防臭纤维织物产品进行了实验室和小型实验池中水华藻杀灭实验。结果显示,在28℃光照强度3 000 lx条件下,在实验室培养的藻悬浮液中放置0.4 cm2/mL抗菌防臭纤维织物1~3 d后,铜绿微囊藻(Microcystis aeruginosa)DS和7820种、鲍氏织线藻(Plectonema calothrichoidesGom)、莱茵衣藻(Chlamydomonas rein-hardtii)的叶绿素a含量即明显降低,处理2周后,叶绿素a浓度分别下降94.8%、92.7%、93.2%和98.9%;鱼腥藻(Anabae-na7120),斜生栅藻(Scenedesmus obliquusK櫣tz)的生长受到强烈抑制,处理3周后其叶绿素a浓度无明显增加;在1.8 m×2.8 m×1.5 m的小型实验池使用1.25 m2/m3抗菌防臭纤维织物8 d后,实验池野生铜绿微囊藻叶绿素a浓度下降86.8%。鱼类急性毒理测试显示该抗菌防臭纤维织物无毒性。     

Microbial biomass and activity in a Brazilian soil amended with untreated and composted textile sludge

This laboratory study examines the effect of application of untreated and composted textile sludge on microbial biomass and activity in a Brazilian soil. The soil was amended with untreated and composted sludge at rates equivalent of 6.4t ha(-1) (0.64 g per 100g of soil) and 19t ha(-1) (1.90 g per 100g of soil), respectively, and were incubated at 28 degrees C for 60 days and daily sampled for microbial activity. An additional experiment, in the same condition, was conduced for evaluation of microbial biomass and enumeration of microorganisms at 15, 30 and 60 days after incubation. The application of composted sludge increased significantly the microbial biomass and activity, and bacteria number of soil. There were not differences in the microbial activity and bacteria number among the control and untreated sludge amended soils. In conclusion, after 2 months of incubation, the effects of the two amendments on soil microorganisms were: microbial biomass, soil respiration and bacteria number were increased only in composted sludge treated soil. qCO2 and fungi number were not affected by untreated and composted sludge.     

A comprehensive review on textile waste valorization techniques and their applications

Environmental Science and Pollution Research - An increase in population compels the textile industry to expand production to fulfill the apparel requirement, resulting in huge textile waste. These...     

Influence of hydraulic retention time in a two-phase upflow anaerobic sludge blanket reactor treating textile dyeing effluent using sago effluent as the co-substrate

Purpose  

Textile dyeing and sago industries are the most polluting industries in South India, especially in industrial cities like Salem, Tamil Nadu, where textile dyeing and sago industries are clumped together geographically. Conventional physicochemical treatment followed by biological processes for the effluent generated from these industries are ineffective, costlier and produce huge quantities of hazardous sludge and harmful by-products which requires further treatment and safe disposal. Hence, the development of an alternative treatment method will become important. The main objective of this investigation is to establish a sustainable biotreatment technology for the treatment of textile dyeing effluent using sago effluent as co-substrate in a two-phase upflow anaerobic sludge blanket (UASB) reactor.     

Photocatalytic and combined anaerobic-photocatalytic treatment of textile dyes

A photocatalytic process based on immobilized titanium dioxide was used to treat crude solutions of azo, anthraquinone and phthalocyanine textile dyes. In addition, the process was applied to the treat autoxidized chemically reduced azo dyes, i.e. representatives of recalcitrant dye residues after biological sequential anaerobic-aerobic treatment. Photocatalysis was able to remove more than 90% color from crude as well as autoxidized chemically reduced dye solutions. UV-absorbance and COD were also removed but to a lower extent (50% in average). The end products of photocatalytic treatment were not toxic toward methanogenic bacteria. The results demonstrate that photocatalysis can be used as a pre- or post-treatment method to biological anaerobic treatment of dye-containing textile wastewater.     

Assessment of natural coagulants to remediate Tunisian textile wastewater by combining physicochemical,analytical, and toxicological data

Environmental Science and Pollution Research - Due to the complexity and variability of textile wastewater composition, a constant search for new treatment strategies that are efficient,...     

纺织行业废水污染控制技术梗概与进展

纺织行业排放的废水成分复杂 ,是最难净化处理的污水之一。本文概述了纺织行业废水污染控制净化技术的现状 ,并作了相应的评价与分析     

Enzyme-based solutions for textile processing and dye contaminant biodegradation—a review

The textile industry, as recognized conformist and stake industry in the world’s economy, is facing serious environmental challenges. In numerous industries, in practice, various chemical-based processes from initial sizing to final washing are fascinating harsh environment concerns. Some of these chemicals are corrosive to equipment and cause serious damage itself. Therefore, in the twenty-first century, chemical and allied industries quest a paradigm transition from traditional chemical-based concepts to a greener, sustainable, and environmentally friendlier catalytic alternative, both at the laboratory and industrial scales. Bio-based catalysis offers numerous benefits in the context of biotechnological industry and environmental applications. In recent years, bio-based processing has received particular interest among the scientist for inter- and multi-disciplinary investigations in the areas of natural and engineering sciences for the application in biotechnology sector at large and textile industries in particular. Different enzymatic processes such as chemical substitution have been developed or in the process of development for various textile wet processes. In this context, the present review article summarizes current developments and highlights those areas where environment-friendly enzymatic textile processing might play an increasingly important role in the textile industry. In the first part of the review, a special focus has been given to a comparative discussion of the chemical-based “classical/conventional” treatments and the modern enzyme-based treatment processes. Some relevant information is also reported to identify the major research gaps to be worked out in future.     

厌氧滤池处理纺织印染废水的中试研究

对厌氧滤池反应器处理难降解印染废水进行中试研究。结果表明,厌氧滤池反应器水力停留时间(HRT)在8.1～14.6 h之间,进水COD浓度波动较大(500～1 000 mg/L)时,对COD平均去除率为20%。印染废水的BOD5/COD由0.23提高到0.35,废水可生化性明显改善。印染废水中硫酸根浓度略有下降,去除浓度为70 mg/L左右。厌氧滤池进出水颜色明显变化,由紫红色变为蓝黑色,紫外可见光谱分析表明废水中的有机物结构发生变化。     

Combined treatment of textile effluent using the sequence Phanerochaete chrysosporium-ozone.

Textile effluents cause a high environmental impact when released into the environment without correct treatment. In this work, we have evaluated the capacity of treatment of a textile effluent using a biological and a chemical method using the sequence Phanerochaete chrysosporium-ozone. The fungal treatment was performed by direct incubation of a fungus spore suspension in textile effluent for nine days. Then, the effluent was ozonized at pH 11 and room temperature. Color, total organic carbon, molecular mass distribution and total phenols were determined. In biological experiments, enzymatic activity (lignin peroxidase, manganese peroxidase and laccase) were also monitored. Toxicity tests were carried out with Scenedesmus subspicatus and with Escherichia coli. Good decoloration, total phenols reduction and textile effluent molecular mass reduction were obtained during the process. No significant total organic carbon reduction was observed. The toxicity of the textile effluent was reduced with both test organisms showing no inhibition at the end of the treatment.     

Regulating colored textile wastewater by 3/31 wavelength ADMI methods in Taiwan

The wastewater from textile dyeing facilities is difficult to treat satisfactorily because of high compositional variability and high color intensity. To reduce colored effluents discharged into watercourses, the government of Taiwan adopted the Effluent True Color Standard in 1998. The true color discharge limit is 400 American Dye Manufactures Institute (ADMI) units. The adopted analytical method is the ADMI Tristimulus Filter Method (3 wavelength (WL) method), and the 31 WL ADMI method might be also adopted as an alternative for color value measurement. The refractory nature of textile dyes and the introduction of this new regulation present an environmental challenge to the Taiwanese textile industry. The main objectives of this study were to (1) evaluate the efficacy of current wastewater treatment systems for controlling the colored textile wastewater discharges, and (2) evaluate the correlations between 3 and 31 WL ADMI methods. Ten representative textile wastewater treatment facilities employing biological and chemical coagulation treatment technologies were selected to perform a 10-consecutive-day effluent sampling and analysis. Results show that a significant difference between 3 and 31 ADMI methods was observed. These two ADMI methods cannot be substituted for each other, and the discharge standard should be determined based on the selected testing method. Investigation results also suggest that the commonly used wastewater treatment technology (biological + chemical coagulation) fails to effectively remove dye from the colored textile wastewater. Sodium hypochlorite (NaOCl) addition was applied by most facilities as the temporary post-polishment step to comply with the color discharge standard.     

Treatability studies on wastewater from textile dyeing factories in Bursa, Turkey

The textile industry is one of the most rapidly developing industries in Turkey. It generates a large amount of wastewater, with corresponding concerns about pollution. The main sources of pollution in wastewater are the dyeing and finishing processes. The dyestuffs and polyvinyl alcohol (PVA) are the main refractory organics of concern in terms of meeting more stringent effluent standards of chemical oxygen demand (COD) and colour. In this study, wastewaters from textile dyeing factories in Bursa were characterised, and physical, chemical and biological treatability studies were carried out. In the physical and chemical studies, 60.80% COD, 80% suspended solids (SS) and 10.92% turbidity removal efficiencies were obtained. In the biological studies, 90% COD and 40% SS removal were obtained. The initial soluble inert COD of wastewater was determined by using comparison methods. The initial inert COD of wastewater and the microbial product concentration were determined as 37 mg/l and 13 mg/l, respectively.     

Vermiremediation of dyeing sludge from textile mill with the help of exotic earthworm Eisenia fetida Savigny

The aim of present study was for the vermiremediation of dyeing sludge from textile mill into nutrient-rich vermicompost using earthworm Eisenia fetida. The dyeing sludge was mixed with cattle dung in different ratios, i.e., 0:100 (D₀), 25:75 (D₂₅), 50:50 (D₅₀), 75:25 (D₇₅), and 100:0 (D₁₀₀) with earthworms, and 0:100 (S₀), 25:75 (S₂₅), 50:50 (S₅₀), 75:25 (S₇₅), and 100:0 (S₁₀₀) without earthworms. Minimum mortality and maximum population build-up were observed in a 25:75 mixture. Nitrogen, phosphorus, sodium, and pH increased from the initial to the final products with earthworms, while electrical conductivity, C/N ratio, organic carbon, and potassium declined in all the feed mixtures. Vermicomposting with E. fetida was better for composting to change this sludge into nutrient-rich manure.     

Adsorption/desorption of copper by a sandy soil amended with various rates of manure, sewage sludge, and incinerated sewage sludge

Organic amendments are sometimes applied to agricultural soils to improve the physical, chemical, and microbiological properties of the soils. The organic fractions in these soil amendments also influence metal reaction, particularly the adsorption and desorption of metals, which, in turn, determine the bioavailability of the metals and hence their phytotoxicities. In this study, a Quincy fine sandy (mixed, mesic, Xeric Torripsamments) soil was treated with 0 to 160 g kg(-1) rates of either manure, sewage sludge (SS), or incinerated sewage sludge (ISS) and equilibrated in a greenhouse at near field capacity moisture content for 100 days. Following the incubation period, the soil was dried and adsorption of copper (Cu) was evaluated in a batch equilibration study at either 0, 100, 200, or 400 mg L(-1) Cu concentrations in a 0.01M CaCl2 solution. The desorption of adsorbed Cu was evaluated by three successive elutions in 0.01M CaCl2. Copper adsorption increased with an increase in manure rates. At the highest rate of manure addition (160 g kg(-1) soil), Cu adsorption was two-fold greater than that by the unamended soil at all rates of Cu additions. With increasing rates of Cu additions, the adsorption of Cu decreased from 99.4 to 77.6% of Cu applied to the 160 g kg(-1) manure amended soil. The desorption of Cu decreased with an increase in rate of manure amendment. Effects of sewage sludge amendments on Cu adsorption were somewhat similar to those as described for manure additions. Likewise, the desorption of Cu was the least at the high rate of SS addition (160 g kg(-1)), although at the lower rates there was not a clear indication of the rate effects. In contrast to the above two amendments, the ISS amendment had the least effect on Cu adsorption. At the highest rate of ISS amendment, the Cu adsorption was roughly 50% of that at the similar rate of either manure or SS amendments, across all Cu rates.     

Pyrolytic characteristics of sewage sludge

In this study, a number of different sewage sludge including sludge samples from industrial and hospital wastewater treatment plants were characterized for pyrolysis behavior by means of thermogravimetric analysis up to 800 degrees C. According to the thermogravimetric results, five different types of mass loss behaviors were observed depending on the nature of the sludge used. Typical main decomposition steps occurred between 250 and 550 degrees C although some still decomposed at higher temperatures. The first group (Types I, II and III) was identified by main decomposition at approximately 300 degrees C and possible second reaction at higher temperature. Differences in the behavior may be due to different components in the sludge both quantitatively and qualitatively. The second group (Types IV and V), which rarely found, has unusual properties. DTG peaks were found at 293, 388 and 481 degrees C for Type IV and 255 and 397 degrees C for Type V. Kinetics of sludge decomposition can be described by either pseudo single or multicomponent overall models (PSOM or PMOM). The activation energy of the first reaction, corresponding to the main pyrolysis typically at 300 degrees C, was rather constant (between 68 and 77 kJ mol(-1)) while those of second and third reactions were varied in the range of 85-185 kJ mol(-1). The typical order of pyrolysis reaction was in the range of 1.1-2.1. The pyrolysis gases were composed of both saturated and unsaturated light hydrocarbons, carbon dioxide, ethanol and chloromethane. Most products, however, evolve at a quite similar temperature regardless of the sludge type.     

Autotrophic nitrogen removal for decentralized treatment of ammonia-rich industrial textile wastewater: process assessment,stabilization and modelling

Environmental Science and Pollution Research - Digital textile printing (DTP) is a game-changer technology that is rapidly expanding worldwide. On the other hand, process wastewater is rich in...