TiO₂ supported over SBA-15: an efficient photocatalyst for the pesticide degradation using solar light

Photocatalytic degradation and mineralization of pesticides are studied over TiO(2) supported mesoporous SBA-15 composite system using solar light. TiO(2) is immobilized over SBA-15 by solid sate dispersion method. The catalysts are characterized by XRD, surface area, UV-Vis diffused reflectance spectra, SEM and TEM. The detailed photocatalytic degradation studies are carried out over TiO(2), SBA-15 and different TiO(2) wt% supported SBA-15. The activity evaluation parameters such as catalyst amount, pH, and pollutant initial concentration are studied taking isoproturon as a model compound and established conditions for pesticide degradation. The optimum degradation is achieved over 10 wt% TiO(2)/SBA-15 within 30 min and the reaction is following pseudo-first order kinetics. The isoproturon mineralization is monitored with TOC reduction and it takes around 9h for disappearance. The commercial pesticide solutions containing imidacloprid and phosphamidon are also successfully degraded over these composites with the established conditions. The data indicates that 10 wt% TiO(2)/SBA-15 composite is an effective and highly active system for the pesticide degradations.     

Photocatalytic degradation of isoproturon herbicide over TiO2/Al-MCM-41 composite systems using solar light

The present investigation covers immobilization of TiO2 using a simple solid state dispersion technique over mesoporous Al-MCM-41 support for the treatment of isoproturon herbicide. Catalysts are characterized by XRD, X-ray photo electron spectroscopy (XPS), surface area, UV-Vis diffused reflectance spectra (DRS), SEM and TEM. A detailed photocatalytic degradation study of isoproturon under solar light in aqueous suspensions is reported. The 10 wt% TiO2/Al-MCM-41 composite system found to be optimum with high degradation activity. The reaction follows pseudo-first order kinetics. The parameters like TiO2 loading over Al-MCM-41, amount of catalyst, concentration of substrate, pH effect, durability of the catalyst, activity comparison of TiO2 and Al-MCM-41 supported system are studied. The mineralization of isoproturon is monitored by TOC. Based on the degradation products detected through LC-MS, a plausible degradation mechanism is proposed. The data indicates that TiO2/Al-MCM-41 composite system is an effective photocatalyst for treatment of isoproturon in contaminated water.     

Ba/TiO2/MCM-41光催化降解对硝基苯甲酸

以钛酸丁酯为钛源、MCM-41分子筛为载体,采用溶胶-凝胶法制备了掺杂与负载相结合的光催化剂Ba/TiO2/MCM-41。结果表明:Ba/TiO2/MCM-41是一种比表面积高达341.2 m2/g的介孔材料,主要晶相为锐钛矿相,比P25有更强的紫外光吸收。将Ba/TiO2/MCM-41用于光催化氧化水中的对硝基苯甲酸,当催化剂投加量为0.5 g/L,对硝基苯甲酸初始pH为4、浓度为2×10-4mol/L时,紫外光照30 min后,对硝基苯甲酸降解率达到96.0%。用紫外光谱、红外光谱和高效液相色谱分析对硝基苯甲酸降解前后的变化,发现随着光照时间延长,苯环上的硝基、羧基吸收峰逐渐减弱;对硝基苯甲酸首先被降解为一些中间小分子产物,随着反应进行,小分子物质也逐渐被降解。     

Ba/TiO_2/MCM-41光催化降解对硝基苯甲酸

以钛酸丁酯为钛源、MCM-41分子筛为载体,采用溶胶-凝胶法制备了掺杂与负载相结合的光催化剂Ba/TiO2/MCM-41。结果表明：Ba/TiO2/MCM-41是一种比表面积高达341.2 m2/g的介孔材料,主要晶相为锐钛矿相,比P25有更强的紫外光吸收。将Ba/TiO2/MCM-41用于光催化氧化水中的对硝基苯甲酸,当催化剂投加量为0.5 g/L,对硝基苯甲酸初始pH为4、浓度为2×10-4mol/L时,紫外光照30 min后,对硝基苯甲酸降解率达到96.0%。用紫外光谱、红外光谱和高效液相色谱分析对硝基苯甲酸降解前后的变化,发现随着光照时间延长,苯环上的硝基、羧基吸收峰逐渐减弱;对硝基苯甲酸首先被降解为一些中间小分子产物,随着反应进行,小分子物质也逐渐被降解。     

Effect of CO on NO oxidation over platinum based catalysts for hybrid fast SCR process

The oxidation characteristics of NO over Pt/TiO2 (anatase, rutile) catalysts have been determined in a fixed bed reactor as a function of O2, CO and SO2 concentrations in the presence of 8% water. The conversion of NO to NO2 increases with increasing O2 concentration up to 12% and it levels off. This saturation effect is more pronounced over rutile-Pt/TiO2 (r-Pt/TiO2) than that of anatase-Pt/TiO2 (a-Pt/TiO2). The presence of CO increases NO oxidation significantly and this enhanced effect is more pronounced on a-Pt/TiO2 than that on r-Pt/TiO2 with increasing CO concentration at lower temperatures. The same effect is also observed on the catalysts with different Pt and tungsten oxide (WO3) loadings. With increasing Pt and WO3 loadings on TiO2 support (Pt-WO3/TiO2), formation of NO2 is high even at lower temperatures. The presence of SO2 significantly suppresses the oxidation of NO over both r-Pt/TiO2 and a-Pt/TiO2 catalysts but it is less pronounced due to low stability of sulfate on a-Pt/TiO2.     

臭氧与TiO2/UV协同降解对氯苯酚

利用O3／UV、TiO2／UV和O3／TiO2／UV降解对氯苯酚表明，臭氧与TiO2／UV具有明显的协同作用，如在本实验条件下降解5min后，上述3者对对氯苯酚的去除率分别为55％、10％和77%。O3／TiO2／UV协同作用的本质是由于臭氧能带走二氧化钛光致电子空穴对中的电子，从而产生了更多的羟基自由基，加速了有机物的降解。     

N-doped SiO2/TiO2 mesoporous nanoparticles with enhanced photocatalytic activity under visible-light irradiation

Mesoporous nanocrystalline N-doped SiO2/TiO2 visible-light photocatalysts were prepared by treating SiO2/TiO2 xerogels in a flow of nitrogen gas bubbled through concentrated ammonia solution. Structural characterization and performance analysis results revealed that the addition of SiO2 remarkably altered the phase composition, specific surface area, microstructure, as well as the photocatalytic activity of N-doped TiO2. The presence of SiO2 in N-doped TiO2 particles suppressed the formation of rutile phase and the crystal growth of N-doped TiO2 particles during thermal calcinations. When weight ratio of SiO2/TiO2 was in 0.05-0.20, the N-doped SiO2/TiO2 exhibited higher photocatalytic activity than the N-doped TiO2, and optimum ratio was found to be 0.05. The enhanced photocatalytic activity could be attributed to the higher specific area, larger pore volume, and more surface hydroxyl groups in the catalyst.     

The preparation of Zn2+-doped TiO(2) nanoparticles by sol-gel and solid phase reaction methods respectively and their photocatalytic activities

The photocatalytic oxidation of the organic pollutants with TiO(2) as photocatalyst has been widely studied in the world, and many achievements have been made. The degradation of pollutants is highly related to the photocatalytic activity of TiO(2). It is demonstrated that doping ions to TiO(2) is one way to enhance the photocatalytic activity of TiO(2). In this paper, Zn(2+)-doped TiO(2) nanoparticles were prepared through sol-gel and solid phase reaction methods, characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by sol-gel method is close to that of pure TiO(2) particles, however, the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by solid phase reaction method is much higher than that of pure TiO(2) particles. The most efficient degradation of Rhodamine B was found with TiO(2) particles doped with 0.5% Zn(2+) in mole and calcined at 500 degrees C. Also the reason for the enhancement of the photocatalytic activity of TiO(2) by Zn(2+) doping through solid phase reaction method was discussed.     

Effect of ZnFe2O4 doping on the photocatalytic activity of TiO2

The photocatalytic oxidation of the organic pollutants with the TiO2 as photocatalyst has been widely studied in the world, and many achievements have been got. The degradation of pollutants is highly related with the photocatalytic activity of TiO2. It is demonstrated that doping ions or oxides to TiO2 is one way to enhance the photocatalytic activity of TiO2. In this paper, the ZnFe2O4-doped TiO2 nanoparticles were prepared from butyl titanate by a sol-gel method and characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results showed that when TiO2 was doped with ZnFe2O4, its particle size will decrease and its crystal structure will partly transform from anatase to rutile. The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that doping ZnFe2O4 to TiO2 will enhance the photocatalytic activity of TiO2 and that ZnFe2O4-doped TiO2 in the coexistence of anatase and rutile has higher efficiency for the degradation of Rhodamine B than that in the anatase phase alone. Also the different role of O2 in the direct photolysis and photocatalysis of Rhodamine B was discussed.     

Genotoxicity of titanium dioxide (TiO2) nanoparticles at two trophic levels: plant and human lymphocytes

The environmental fate and behaviour of titanium dioxide (TiO(2)) nanoparticles is a rapidly expanding area of research. There is a paucity of information regarding toxic effect of TiO(2) nanoparticles in plants and to certain extent in humans. The present study focuses on the effect of exposure of TiO(2) nanoparticles in two trophic levels, plant and human lymphocytes. The genotoxicity of TiO(2) nanoparticles was evaluated using classical genotoxic endpoints, comet assay and DNA laddering technique. DNA damaging potential of TiO(2) nanoparticles in Allium cepa and Nicotiana tabacum as representative of plant system could be confirmed in the comet assay and DNA laddering experiments. In Allium micronuclei and chromosomal aberrations correlated with the reduction in root growth. We detected increased level of malondialdehyde (MDA) concentration at 4mM (0.9 μM) treatment dose of TiO(2) nanoparticles in Allium cepa. This indicated that lipid peroxidation could be involved as one of the mechanism leading to DNA damage. A comparative study of the cytotoxic and genotoxic potential of TiO(2) nanoparticles and bulk TiO(2) particles in human lymphocytes also reveal interesting results. While TiO(2) nanoparticles were found to be genotoxic at a low dose of 0.25 mM followed by a decrease in extent of DNA damage at higher concentrations; bulk TiO(2) particles reveal a more or less dose dependent effect, genotoxic only at dose 1.25 mM and above. The study thus confirms the genotoxic potential of TiO(2) nanoparticles in both plant and human lymphocytes.     

TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

Photodegradation of alachlor with the TiO(2) film immobilised on the glass tube in aqueous solution

Alachlor photodegradation was performed using TiO(2), which was synthesized by a modified sol-gel method. The thickness of a TiO(2) film immobilised by a 5-time dip-coating was 174 nm and the average diameter of TiO(2) particles was about 10-15 nm in SEM images. The crystal structure of a TiO(2) film calcinated at 300 degrees C for 1 h was observed as a typical anatase type. The stability of a TiO(2) film by a modified sol-gel method was 4% better than TiO(2) by a typical sol-gel method.The removal rate of alachlor with both Fe(3+) and UV radiation in the absence of TiO(2) was 0.28 mg/l/h in 10 h and the removal rate of alachlor with Fe(3+)/UV in the presence of TiO(2) was 0.32 g/l/h, which was higher by 14% than that with Fe(3+)/UV system. TOC concentration during the alachlor degradation with both TiO(2) and UV radiation in the absence of added Fe(3+) decreased from 100%, through 81% and 51%, to 44% with time elapses of 4, 8, and 10 h, respectively, while TOC concentration with both added Fe(3+) and UV radiation in the absence of TiO(2) decreased from 100% to 70% in 10 h.     

Enhanced bioaccumulation of cadmium in carp in the presence of titanium dioxide nanoparticles

In this study adsorption of Cd onto TiO2 nanoparticles and natural sediment particles (SP) were studied and the facilitated transports of Cd into carp by TiO2 nanoparticles and SP were assessed by bioaccumulation tests exposing carp (Cyprinus carpio) to Cd contaminated water in the presence of TiO2 and SP respectively. The results show that TiO2 nanoparticles had a significantly stronger adsorption capacity for Cd than SP. The presence of SP did not have significant influence on the accumulation of Cd in carp during the 25 d of exposure. However, the presence of TiO2 nanoparticles greatly enhanced the accumulation of Cd in carp. After 25 d of exposure Cd concentration in carp increased by 146%, and the value was 22.3 and 9.07 microg/g, respectively. And there is a positive correlation between Cd and TiO2 concentration. Considerable Cd and TiO2 accumulated in viscera and gills of the fish.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

TiO_2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有：X射线衍射光谱（XRD）、激光散射粒径分布、傅立叶变换红外光谱（FT-IR）、X射线光电子谱（XPS）和透射电子显微镜（TEM）。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂（H2O2）用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明：制备的TiO2胶体粒子平均粒径为13.8 nm（激光散法测定）,光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/（L.min）,平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2（含量30%）用量为0.2%（V/V）,光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

The use of oxyhalogen in photocatalytic reaction to remove o-chloroaniline in TiO2 dispersion

Photodecay of o-chloroaniline (o-ClA) in various combinations of UV sources, TiO2, and oxyhalogens was investigated. To improve the conventional photocatalytic process by using UV/TiO2, the addition of oxyhalogens (ClO3(-), BrO3(-) and IO3(-)) into UV/TiO2 system was studied and the effect in such addition is very encouraging for all the selected additives. Oxyhalogens are capable of deferring the electron-hole recombination of TiO2 which significantly improved its catalytic performance. The presence of IO3(-) in UV/TiO2 resulted in the fastest o-ClA decay among three oxhalogens at the same dosage. The decay of o-ClA in UV/TiO2/oxyhalogen process is characterized by a two-stage pseudo-kinetics, where a faster initial decay was followed by a retardation state. A mathematics model was successfully established for the prediction of the two-stage decay of o-ClA in UV/TiO2/IO3(-) with any designed [IO3(-)] concentration.     

TiO2-catalyzed photooxidation of arsenite to arsenate in aqueous samples

The TiO2-catalyzed photooxidation of arsenite (As(III)) to arsenate (As(V)) was studied in aqueous TiO2 suspensions using a solar simulator which emitted ultraviolet and visible radiations. The concentration of As(III) was varied between 50 microg l(-1) and 10 mg l(-1), and the concentration of TiO2 between 1 mg l(-1) and 50 mg l(-1). Total oxidation of As(III) to As(V) occurred within minutes. The concentration of As(III) declined exponentially which indicates first-order kinetics. In the pH range between 5 and 9 there was no significant influence of the pH of the suspension on the reaction rate. Batch experiments without irradiation showed that part of the arsenic was adsorbed on the TiO2 surface. When using 100 microg l(-1) As and between 1 mg l(-1) and 50 mg l(-1) TiO2, 8-39% of As(III) and up to 73% of As(V) were adsorbed by TiO2. As(III) was also oxidized by UV radiation in the absence of TiO2, but the reaction was slower than in the presence of TiO2 resulting in an irradiation time too long for practical use. In addition, oxidation of As(III) in the presence of TiO2 was also observed under solar irradiation within a few minutes.     

The light transmission and distribution in an optical fiber coated with TiO2 particles

The light delivery and distribution phenomena along the optical fiber coated with the P-25 TiO(2) particles by dipping was investigated. The surface properties (coverage, roughness and thickness) of the TiO(2) layer coated on the optical fiber were characterized by SEM micrographs. For TiO(2) layer prepared from solutions containing less than 20 wt.% of TiO(2) slurry, the thickness of layer was increased linearly with the TiO(2) slurry content in solutions. The UV light intensity transmitted along a TiO(2)-coated optical fiber decreased more rapidly than that transmitted along a non-coated fiber. Based on the experimental results, the light intensity distribution around a coated optical fiber was modeled to determine the optimum configuration for the design of optical fiber reactors under various operational conditions.     

V/Ce共掺杂TiO2光催化降解甲醛的实验研究

采用溶胶-凝胶法制备了不掺杂、V掺杂、Ce掺杂、V/Ce共掺杂纳米TiO2光催化剂,并将其分别负载于瓷砖上,利用X射线衍射分析（XRD）和扫描电镜分析（SEM）技术对薄膜样品的结构和形貌进行了表征。通过对甲醛的降解实验评价光催化剂的光催化活性。实验结果表明,光催化剂的负载量、共掺杂离子的掺杂量、掺杂配比、煅烧温度影响纳米TiO2的光催化活性。V/Ce共掺杂TiO2光催化剂产生了协同效应,其光催化活性优于纯TiO2和单掺杂TiO2样品。