Comparative study of adsorption of Pb(II) on native garlic peel and mercerized garlic peel

A comparative study using native garlic peel and mercerized garlic peel as adsorbents for the removal of Pb²⁺ has been proposed. Under the optimized pH, contact time, and adsorbent dosage, the adsorption capacity of garlic peel after mercerization was increased 2.1 times and up to 109.05 mg g^?1. The equilibrium sorption data for both garlic peels fitted well with Langmuir adsorption isotherm, and the adsorbent–adsorbate kinetics followed pseudo-second-order model. These both garlic peels were characterized by elemental analysis, Fourier transform infrared spectrometry (FT-IR), and scanning electron microscopy, and the results indicated that mercerized garlic peel offers more little pores acted as adsorption sites than native garlic peel and has lower polymerization and crystalline and more accessible functional hydroxyl groups, which resulted in higher adsorption capacity than native garlic peel. The FT-IR and X-ray photoelectron spectroscopy analyses of both garlic peels before and after loaded with Pb²⁺ further illustrated that lead was adsorbed on the through chelation between Pb²⁺ and O atom existed on the surface of garlic peels. These results described above showed that garlic peel after mercerization can be a more attractive adsorbent due to its faster sorption uptake and higher capacity.     

Removal of arsenic(III,V) by a granular Mn-oxide-doped Al oxide adsorbent: surface characterization and performance

In order to remove arsenic (As) from contaminated water, granular Mn-oxide-doped Al oxide (GMAO) was fabricated using the compression method with the addition of organic binder. The analysis results of XRD, SEM, and BET indicated that GMAO was microporous with a large specific surface area of 54.26 m^2/g, and it was formed through the aggregation of massive Al/Mn oxide nanoparticles with an amorphous pattern. EDX, mapping, FTIR, and XPS results showed the uniform distribution of Al/Mn elements and numerous hydroxyl groups on the adsorbent surface. Compression tests indicated a satisfactory mechanical strength of GMAO. Batch adsorption results showed that As(V) adsorption achieved equilibrium faster than As(III), whereas the maximum adsorption capacity of As(III) estimated from the Langmuir isotherm at 25 °C (48.52 mg/g) was greater than that of As(V) (37.94 mg/g). The As removal efficiency could be maintained in a wide pH range of 3~8. The presence of phosphate posed a significant adverse effect on As adsorption due to the competition mechanisms. In contrast, Ca²⁺ and Mg²⁺ could favor As adsorption via cation-bridge involvement. A regeneration method was developed by using sodium hydroxide solution for As elution from saturated adsorbents, which permitted GMAO to keep over 75% of its As adsorption capacity even after five adsorption–regeneration cycles. Column experiments showed that the breakthrough volumes for the treatment of As(III)-spiked and As(V)-spiked water (As concentration = 100 μg/L) were 2224 and 1952, respectively. Overall, GMAO is a potential adsorbent for effectively removing As from As-contaminated groundwater in filter application.

     

Chromium (VI) remediation in aqueous solution by waste products (peel and seed) of mango (Mangifera indica L.) cultivars

The surface group characteristics of mango cultivar peels and seeds were evaluated by infrared spectra, PZC, and functional group composition. The adsorption/reduction of chromium (VI) in aqueous solutions was investigated by varying pH, contact time, initial Cr(VI) concentration, and adsorbent amount. The results show that both peel and seed powders of the mango cultivars showed significant adsorption/reduction capacity for Cr(VI) and that the desorption process obeys pseudo-second-order kinetics. Optimal adsorption occurred at pH 1.0, using a Cr(VI) concentration of 100 mg/L. On average, at pH 1.0, and a concentration of 3 g/L, the maximum adsorption/reduction capacity of Cr(VI) was 83% (peels 76%, seeds 90%). Of the mango powders tested, the most efficient were Tommy seed (100%) and Coite peel (98%) followed by Coite seed (96%) and Tommy peel powders (95%). The adsorption/reduction of Cr(VI) was complete (100%) by the mango seed, in comparison to the peel powders (97%) after 180 min. The data indicates that mango waste products, such as seed and peel powders, are both excellent candidates for the remediation of Cr(VI) from aqueous systems and due to the higher concentration of gallates and galloyl glucosides, the mango seed powders should be the powders of choice for future remediation projects.

     

活化赤泥的除氟性能

以成本低的铝工业废矿渣（赤泥）为原材料,通过高温煅烧和酸化处理对赤泥进行活化,制备了除氟吸附剂。研究了反应时间、投加量、初始氟浓度、溶液温度、共存阴离子和pH值对活化赤泥除氟效果的影响。结果表明,接触反应时间为18 h时,吸附接近平衡。活化赤泥对氟离子的吸附符合Lagergren二级吸附动力学方程。另外,初始浓度越高,吸附容量越大。与Freundlich相比,Langmuir吸附等温模型可以更好地描述氟离子的吸附特性,最大吸附量可达2.71 mg/g。SO24-、Cl-和NO3-存在时（〈1 000 mg/L）,对氟离子的吸附几乎没有影响,然而,HCO3-、PO34-和氟离子共存时,会对氟吸附造成不利影响。活化赤泥在pH值3.5～11.0时,具有较好的吸附稳定性。活化赤泥是一种吸附容量高、性能稳定的环境友好型除氟材料,具有应用潜力。     

非活体生物质对水中活性艳红X-3B的吸附研究

研究了4种非活体生物质(米酒糟、花生壳、柚子皮、稻草秸秆)对模拟废水中活性艳红X-3B的吸附条件及吸附机理。结果表明,活性艳红X-3B初始浓度为100 mg/L、pH为1.0~2.0、吸附剂浓度为10 mg/L时,4种吸附剂对活性艳红X-3B的吸附率可达到80%。吸附在60 min左右达平衡后最大吸附量的顺序为:米酒糟(58.8 mg/g)花生壳(28.0mg/g)柚子皮(23.6 mg/g)稻草秸秆(19.5 mg/g)。在达最大吸附率时,米酒糟的用量可减少一半、pH范围可宽为1.0~6.0,且吸附量是另三者的2倍以上。综合比较,米酒糟具有较强的吸附废水中活性艳红X-3B的能力,可作为废水中活性染料的吸附剂使用。而花生壳、柚子皮和稻草秸秆的吸附能力相对较弱,不是理想的吸附材料。数学模型模拟表明,米酒糟和柚子皮的吸附过程更符合Freundlich方程,而花生壳和稻草秸秆更符合Langmuir方程;动力学研究表明4种吸附剂的吸附拟合更符合拟二级动力学方程。     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

Removal and Destruction of Organic Contaminants in Water Using Adsorption,Steam Regeneration,and Photocatalytic Oxidation: A Pilot-Scale Study

ABSTRACT

The overall objective of this pilot-scale study is to investigate the technical feasibility of the removal and destruction of organic contaminants in water using adsorption and photocatalytic oxidation. The process consists of two consecutive operational steps: (1) removal of organic contaminants using fixed-bed adsorption; and (2) regeneration of spent adsorbent using photocatalysis or steam, followed by decontamination of steam condensate using photocatalysis. The pilot-scale study was conducted to evaluate these options at a water treatment plant in Wausau (Wisconsin) for treatment of groundwater contaminated with tetrachloroethene (PCE), trichloroethene (TCE), cis-dichloroethene (cis-DCE), toluene, ethylbenzene (EB), and xylenes. The adsorbents used were F-400 GAC and Ambersorb 563.

In the first treatment strategy, the adsorbents were impregnated with photocatalyst and used for the removal of aqueous organics. The spent adsorbents were then exposed to ultraviolet light to achieve photocatalytic regeneration. Regeneration of adsorbents using photocatalysis was observed to be not effective, probably because the impregnated photocatalyst was fouled by background organic matter present in the groundwater matrix.

In the second treatment strategy, the spent adsorbents were regenerated using steam, followed by cleanup of steam condensate using photocatalysis. Four cycles of adsorption and three cycles of steam regeneration were performed. Ambersorb 563 adsorbent was successfully regenerated using saturated steam at 160 °C within 20 hours. The steam condensate was treated using fixed-bed photo-catalysis using 1% Pt-TiO₂ photocatalyst supported on silica gel. After 35 minutes of empty bed contact time, more than 95% removal of TCE, cis-DCE, toluene, EB, and xylenes was achieved, and more than 75% removal of PCE was observed.

In the case of activated carbon adsorbent, steam regeneration was not effective, and a significant loss in adsorbent capacity was observed.     

Graphene—a promising material for removal of perchlorate (ClO4 −) from water

A batch adsorption process was applied to investigate the removal of perchlorate (ClO₄ ^?) from water by graphene. In doing so, the thermodynamic adsorption isotherm and kinetic studies were also carried out. Graphene was prepared by a facile liquid-phase exfoliation. Graphene was characterized by Raman spectroscopy, Fourier-transform infrared spectroscopy, powder X-ray diffraction, scanning electron microscope, and zeta potential measurements. A systematic study of the adsorption process was performed by varying pH, ionic strength, and temperature. The adsorption efficiency of graphene was 99.2 %, suggesting that graphene is an excellent adsorbent for ClO₄ ^? removal from water. The rate constants for all these kinetic models were calculated, and the results indicate that second-order kinetics model was well suitable to model the kinetic adsorption of ClO₄ ^?. Equilibrium data were well described by the typical Langmuir adsorption isotherm. The experimental results showed that graphene is an excellent perchlorate adsorbent with an adsorbent capacity of up to 0.024 mg/g at initial perchlorate concentration of 2 mg/L and temperature of 298 K. Thermodynamic studies revealed that the adsorption reaction was a spontaneous and endothermic process. Graphene removed the perchlorate present in the water and reduced it to a permissible level making it drinkable.     

Selective removal of Cr(VI) from aqueous solution by adsorption on mangosteen peel

Mangosteen peel, rich in polyphenolic compounds, was used to prepare the adsorbent exhibiting highly selective adsorption for Cr(VI) over other metal ions such as Pb²⁺, Fe³⁺, Zn²⁺, Cd²⁺, and Cr³⁺ at the pH values of 1～4. The chemical modification method proposed by using calcium hydroxide is quite cost-effective and ecofriendly without using any toxic reagents or causing any secondary pollution. The adsorption isotherm results revealed that the adsorption of Cr(VI) on the gel fit well the Langmuir adsorption model, and the maximum adsorption capacity for Cr(VI) at pH levels 1, 2, 3, and 4 was evaluated to be 2.46, 2.44, 1.99, and 2.14 mol/kg, respectively. The adsorption mechanism for Cr(VI) on the saponified gel was verified to follow an esterifiaction reaction coupled with the reduction of Cr(VI) to Cr(III) in which H⁺ plays a role of promoter. Thus, modified mangosteen peel gel has the prominent selectivity and low cost for Cr(VI) removal.     

Temperature-responsive graphene oxide/N-isopropylacrylamide/2-allylphenol nanocomposite for the removal of phenol and 2,4-dichlorophenol from aqueous solution

In this study, a novel thermo-responsive polymer was synthesized with efficient grafting of N-isopropylacrylamide as a thermosensitive polymer onto the graphene oxide surface for the efficient removal of phenol and 2,4-dichlorophenol from aqueous solutions. The synthesized polymer was conjugated with 2-allylphenol. Phenol and 2,4-dichlorophenol were monitored by ultra-performance liquid chromatography system equipped with a photodiode array detector. The nanoadsorbent was characterized by different techniques. The nanoadsorbent revealed high adsorption capacity where the removal percentages of 91 and 99% were found under optimal conditions for phenol and 2,4-dichlorophenol, respectively (for phenol; adsorbent dosage = 0.005 g, pH = 8, temperature= 25 °C, contact time = 60 min; for 2,4-dichlorophenol; adsorbent dosage = 0.005 g, pH = 5, temperature = 25 °C, contact time = 10 min). Adsorption of phenol and 2,4-dichlorophenol onto nanoadsorbent followed pseudo-second-order kinetic and Langmuir isotherm models, respectively. The values of ΔG (average value = ? 11.39 kJ mol^?1 for phenol and 13.42 kJ mol^?1 for 2,4-dichlorophenol), ΔH (? 431.72 J mol^?1 for phenol and ? 15,721.8 J mol^?1 for 2,4-dichlorophenol), and ΔS (35.39 J mol^?1 K^?1 for phenol and ? 7.40 J mol^?1 K^?1 for 2,4-dichlorophenol) confirmed spontaneous and exothermic adsorption. The reusability study indicated that the adsorbent can be reused in the wastewater treatment application. Thermosensitive nanoadsorbent could be used as a low-cost and efficient sorbent for phenol and 2,4-dichlorophenol removal from wastewater samples.

     

巯基化改性膨润土对重金属的吸附性能

以钙基膨润土为基本材料,制备了巯基化改性膨润土,并对比研究了此材料与其他17种改性膨润土和原材料对重金属的吸附性能.结果表明,巯基化膨润土对镉的吸附能力显著优于其他材料,在本实验条件下,其对镉的吸附率高于其他材料30％以上,对镉的吸附量可达52.1 mg/g.巯基化膨润土对铅的吸附能力在重金属竞争吸附条件下优于其他材料,而其对镍的吸附能力在所有材料中处于中等水平;另外,巯基化膨润土对3种重金属的吸附受重金属竞争吸附影响较小.因此,在所研究的材料中,巯基化膨润土材料是一种最理想的重金属吸附材料.     

Production of sugarcane bagasse-based activated carbon for formaldehyde gas removal from potted plants exposure chamber

Agricultural wastes such as rice straw, sugar beet, and sugarcane bagasse have become a critical environmental issue due to growing agriculture demand. This study aimed to investigate the valorization possibility of sugarcane bagasse waste for activated carbon preparation. It also aimed to fully characterize the prepared activated carbon (BET surface area) via scanning electron microscope (SEM) and in terms of surface functional groups to give a basic understanding of its structure and to study the adsorption capacity of the sugarcane bagasse-based activated carbon using aqueous methylene blue (MB). The second main objective was to evaluate the performance of sugarcane bagasse-based activated carbon for indoor volatile organic compounds removal using the formaldehyde gas (HCHO) as reference model in two potted plants chambers. The first chamber was labeled the polluted chamber (containing formaldehyde gas without activated carbon) and the second was taken as the treated chamber (containing formaldehyde gas with activated carbon). The results indicated that the sugarcane bagasse-based activated carbon has a moderate BET surface area (557 m²/g) with total mesoporous volume and microporous volume of 0.310 and 0.273 cm³/g, respectively. The prepared activated carbon had remarkable adsorption capacity for MB. Formaldehyde removal rate was then found to be more than 67% in the treated chamber with the sugarcane bagasse-based activated carbon. The plants’ responses for this application as dry weight, chlorophyll contents, and protein concentration were also investigated.

Implications: Preparation of activated carbon from sugarcane bagasse (SCBAC) is a promising approach to produce cheap and efficient adsorbent for gas pollutants removal. It may be also a solution for the agricultural wastes problems in big cities, particularly in Egypt. MB adsorption tests suggest that the SCBAC have high adsorption capacity. Formaldehyde gas removal in the plant chambers indicates that the SCBAC have potential to recover volatile gases. The results confirmed that the activated carbon produced from sugarcane bagasse waste raw materials can be used as an applicable adsorbent for treating a variety of gas pollutants from the indoor environment.     

Efficacy of biochar in removal of organic pesticide,Bentazone from watershed systems

Abstract

Bentazone is one of the toxic insecticides used to control forest tent caterpillar moths, boll weevils, gypsy moths, and other types of moths in various field crops. We report the efficacy of biochar prepared from the Azardirachta Indica waste biomass as adsorbent for removal of Bentazone. Biochar material was prepared by pyrolysis process under limited oxygen conditions. Biochar material was characterized by proximate and ultimate analysis, SEM analysis, FTIR analysis and TG/DTA analyses. The Bentazone adsorption capacity by biochar from aqueous solutions was assessed. Effect of time, adsorbent dosage, insecticide concentration and pH on the adsorption characteristics of the biochar were evaluated. Adsorption parameters were obtained at equilibrium contact time of 150?min, with biochar dosage of 0.5?g at pH 8. From the optimization studies, desirability of 0.952 was obtained with response (adsorption uptake) of 79.40?mg/g, for initial concentration of insecticide (50?mg/L), adsorbent dosage (0.448?g), time 30.0?min and pH 2. The adsorption isotherm data for the removal of Bentazone fitted well with the Freundlich isotherm. This study indicates that the biochar produced from the bark of Azardirachta Indica biomass could be employed as a potential adsorbent for removal of synthetic organic pollutants from the water streams.     

Adsorption Characteristics of Benzene on Biosolid Adsorbent and Commercial Activated Carbons

Abstract

This study selected biosolids from a petrochemical waste-water treatment plant as the raw material. The sludge was immersed in 0.5-5 M of zinc chloride (ZnCl₂) solutions and pyrolyzed at different temperatures and times. Results indicated that the 1-M ZnCl₂-immersed biosolids pyrolyzed at 500 °C for 30 min could be reused and were optimal biosolid adsorbents for benzene adsorption. Pore volume distribution analysis indicated that the mesopore contributed more than the macropore and micropore in the biosolid adsorbent. The benzene adsorption capacity of the biosolid adsorbent was 65 and 55% of the G206 (granular-activated carbon) and BPL (coal-based activated carbon; Calgon, Carbon Corp.) activated carbons, respectively. Data from the adsorption and desorption cycles indicated that the benzene adsorption capacity of the biosolid adsorbent was insignificantly reduced compared with the first-run capacity of the adsorbent; therefore, the biosolid adsorbent could be reused as a commercial adsorbent, although its production cost is high.     

Surfactant-assisted adsorption of uranyl ions in aqueous solution on TiO2/polythiophene nanocomposite

In this work, hexadecyltrimethylammonium-bromide (HTAB)-modified polythiophene (PTh)/TiO₂ nanocomposite (HTAB/PTh/TiO₂) was applied to remove uranyl ions (UO₂²⁺). FT-IR, XRD, ζ potential, TGA, SEM, and XPS were utilized to obtain the chemical and physical properties of HTAB/PTh/TiO₂. The effects of HTAB content, preparation temperature, and adsorption conditions on UO₂²⁺ removal were investigated comprehensively. And the UO₂²⁺ adsorption process on HTAB/PTh/TiO₂ was fitted to the Sips model with a saturated adsorption capacity of 234.74 mg/g, which was 6 times over TiO₂. The results suggested that the surfactant of HTAB can significantly improve the adsorption ability of TiO₂ for UO₂²⁺ ions. This work provides a strategy of surfactant modification for enhancing the separation and recovery ability of adsorbent toward UO₂²⁺ in the radioactive wastewater.

     

Effect of magnetic field on the removal of copper from aqueous solution using activated carbon derived from rice husk

Adsorptive removal of copper by activated carbon derived from modified rice husk (ACRH) was studied in the presence and absence of magnetic field (MF). The ACRH was prepared from the normal rice husk treated by NaOH solution and subsequent pyrolysis at 450 °C in the absence of oxygen. The physicochemical properties of ACRH's were determined before and after the adsorption process to delineate the adsorption mechanism. The BET analysis confirmed that the fabricated ACRH has a specific surface area of 8.244 m²/g with a mesopore to micropore ratio of 0.974. It was observed that the micropore structure gradually replaced the mesopores, and the surface area of the micropore increased (from 0.9219 to 4.1764 m²/g), and the pore diameter was also decreased from 180.381 to 46.249 Å after pyrolysis. The CHNO/S test result reveals that the carbon content was increased from 42 to 67.8% in the ACRH after pyrolysis. The batch sorption studies were performed by varying the initial adsorbate concentration, temperature, agitation speed, pH, adsorbent dose and contact time for magnetic and non-magnetic conditions to analyze the effect of the magnetic field. The univariate studies show that the maximum experimental adsorption capacity was 4.522 mg/g and 3.855 mg/g, respectively, for these two conditions (representing the magnetic impact) at 25 °C with an adsorbent dose of 2 g/L and an agitation speed of 150 rpm. It was also observed that the removal efficiency was 94.55% and 77.96% (magnetic and non-magnetic condition) at pH 7 with a concentration of 10 mg/L in 2 h. The test result on the impact of exposure time on the magnetic field suggested that the magnetic memory influenced the removal efficiency; after 40 to 60 min, the maximum removal efficiency was achieved, around 80 to 90%. The pseudo-second-order kinetic model was best fitted with the experimental data with a rate constant as 0.1749 and 0.1006 g/mg/min for these two conditions. The Temkin model delineates the adsorption isotherm suggesting the heat generated during the adsorption process is linearly abate with the coverage of the surface area of the adsorbent. The thermodynamic model confirms that the copper adsorption is spontaneous (ΔG = ? 3.91 kJ/mol and ? 6.02 kJ/mol), wherein the negative enthalpy value (ΔH = ? 36.74 kJ/mol and ? 25.74 kJ/mol) suggested that the process is exothermic irrespective of magnetic interference. The significant enhancement of copper removal was observed by incorporating the magnetic field, showing an increase in sorption capacity by 17.48% and a reduction of reaction time by 88.12%.

     

Microwave Process for Volatile Organic Compound Abatement

ABSTRACT

The CHA Corporation has completed the U.S. Air Force Phase II Small Business Innovation Research program to investigate the feasibility of using a novel microwave-based process for the removal and destruction of volatile organic compounds (VOCs) in effluents from noncombustion sources, such as paint booth ventilation streams. Removal of solvents by adsorption, followed by the regeneration of saturated granular activated carbon (GAC) by microwave energy, was achieved in a single fixed-bed reactor. Microwave regeneration of the fixed-bed-saturated carbon restored the original GAC adsorption capacity. After 20 adsorption/regeneration cycles, the adsorption capacity dropped from 13.5 g methyl ethyl ketone (MEK)/100 g GAC to 12.5 g MEK/100 g GAC. During microwave regeneration of the GAC fixed bed, the concentrated desorbed paint solvent was oxidized by passing the solvent mixture through a fixed bed of an oxidation catalyst mixed with silicon carbide in a microwave reactor. A 98% oxidation efficiency was consistently achieved from the oxidation of VOCs in the microwave catalytic reactor.     

Esterification of sugarcane bagasse by citric acid for Pb2+ adsorption: effect of different chemical pretreatment methods

In this study, different pretreatment strategies of sugarcane bagasse prior to citric acid modification were investigated in terms of Pb²⁺ adsorption capacity. Pretreatment strategies included the use of NaOH, HCl, and C₂H₅OH in various concentrations. In order to fundamentally understand how these pretreatment methods affect the modification of sugarcane bagasse by citric acid as well as the Pb²⁺ adsorption capacity of sugarcane bagasse, three main components of sugarcane bagasse namely cellulose, hemicellulose, and lignin were isolated and esterified by citric acid under the same conditions. ATR-FTIR, XPS, SEM, and an analysis of the number of carboxylic acid groups were used to investigate the physicochemical and chemical properties of the materials. These three components were proved to participate in adsorption and induce the esterification with citric acid. Hence, pretreatment with ethanol and 0.01 M NaOH which could retain cellulose, hemicellulose, and lignin in sugarcane bagasse achieved a high Pb²⁺ adsorption capacity, i.e., 122.4 and 97 mg/g after the esterification with citric acid. In contrast, pretreatment with 0.5 M NaOH and 0.1 M HCl removed lignin and hemicellulose, leading to the lowest value of approximately 45 mg/g for citric acid esterified-pretreated sugarcane bagasse. XPS analysis and number of carboxylic group measurement confirmed the esterification between bagasse and citric acid. To understand the adsorption mechanism of adsorbent, two kinetic models including pseudo-first-order model and pseudo-second-order model were applied. The experimental data were well described by the pseudo-second-order model. The adsorption isotherm data were fitted Langmuir and Freundlich.

     

Removal of Pb2+ from aqueous solution by adsorption on chemically modified muskmelon peel

A cost-effective biosorbent was prepared by a green chemical modification process from muskmelon peel by saponification with alkaline solution of Ca(OH)₂. Its adsorption behavior for lead ions was investigated and found to exhibit excellent adsorption properties. Results showed that the optimal equilibrium pH range for 100 % adsorption is from 4 up to 6.4. Adsorption equilibrium was attained within 10 min. The adsorption process can be described well by Langmuir model and pseudo-second-order kinetics equation, respectively. The maximum adsorption capacity for lead ions was found to be 0.81 mol/kg. Pectic acid contained in the muskmelon peel is the main factor responsible for the uptake of lead ions onto the gel, and the chemical modification process presented in this study can be assumed effective to prepare other similar biomaterials. The large adsorption capacity and the fast adsorption rate indicated that chemically saponified muskmelon peel gel in present study has great potential to be used as a cost-effective adsorbent for the removal of lead ions from the water.