共查询到20条相似文献,搜索用时 46 毫秒
1.
研究了均苯四甲酸二酐(PMDA)和乙二胺四乙酸二酐(EDTAD)改性甘蔗渣对重金属离子Cu2+和Zn2+的吸附性能,包括吸附动力学和吸附等温线。结果表明,改性后的甘蔗渣对重金属离子Cu2+和Zn2+的吸附容量有显著提高,对Cu2+和Zn2+吸附等温线均符合Langmuir方程,吸附为单分子层吸附。根据Langmuir方程,PMDA和EDTAD改性甘蔗渣对Cu2+的吸附量分别为60.21和33.45 mg/g,对Zn2+的吸附量分别是70.53和36.53 mg/g。两种改性甘蔗渣对两种金属离子的吸附在30 min内均可完成,用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu2+和Zn2+的改性甘蔗渣进行洗脱再生,再生的吸附剂可反复使用。 相似文献
2.
为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。 相似文献
3.
以前期制得改性块状花生壳为对象,测定改性花生壳等电点,考察离子强度对改性花生壳吸附Cd2+和Pb2+的影响、吸附前后吸附质溶液pH变化情况及蒸馏水、NaCl、HNO3、柠檬酸和EDTA 5种解吸液对Cd2+和Pb2+的解吸效果,并通过X-射线光电子能谱仪和傅里叶变换红外光谱仪对吸附前后的改性花生壳进行表征,推测并证实了改性花生壳对Cd2+和Pb2+可能的吸附机理。结果表明,改性花生壳对Cd2+和Pb2+可能的吸附机理是:Cd2+是通过外层络合、离子交换和内层络合的联合作用被吸附的;Pb2+主要是与改性花生壳上的O、N等活性基团发生内层络合;此外,改性花生壳表面生成的二氧化锰对Cd2+和Pb2+的吸附也起到一定的作用。 相似文献
4.
制得一种用于重金属废水处理的新型硅烷化改性沸石吸附剂,成本低、效果显著且稳定。通过对改性沸石表征,分析了改性对沸石结构的影响。结果表明,改性一定程度降低了原沸石的晶体特征,但基本上保持了其结构组成;硅烷化改性成功地在沸石上接枝了氨基。对硅烷化沸石的特性研究,得出硅烷化沸石对Ni2+、Cu2+、Zn2+和Pb2+吸附最佳投加量为1、1、1.6和0.6 g/L,且此时对4种离子的去除率也较好;吸附动力学研究得出,其吸附过程可用二级动力学方程较好地拟合;吸附达到平衡时,4种金属离子的平衡吸附量分别为11.23、17.41、15.45和59.42 mg/g;硅烷化沸石对金属离子的吸附行为更符合Langmuir模型,为化学吸附;在酸性条件下(pH=2~6),硅烷化沸石仍保持一定的吸附能力,具有一定的耐酸性。 相似文献
5.
The present study aims to evaluate the competitive biosorption of lead, cadmium, copper, and arsenic ions by using native algae. A series of experiments were carried out in a batch reactor to obtain equilibrium data for adsorption of single, binary, ternary, and quaternary metal solutions. The biosorption of these metals is based on ion exchange mechanism accompanied by the release of light metals such as calcium, magnesium, and sodium. Experimental parameters such as pH, initial metal concentrations, and temperature were studied. The optimum pH found for removal were 5 for Cd 2+ and As 3+ and 3 and 4 for Pb 2+ and Cu 2+, respectively. Fourier transformation infrared spectroscopy analysis was used to find the effects of functional groups of algae in biosorption process. The results showed that Pb 2+ made a greater change in the functional groups of algal biomass due to high affinity to this metal. An ion exchange model was found suitable for describing the biosorption process. The affinity constants sequence calculated for single system was K Pb > K Cu > K Cd > K As; these values reduced in binary, ternary, and quaternary systems. In addition, the experimental data showed that the biosorption of the four metals fitted well the pseudo-second-order kinetics model. 相似文献
6.
Agricultural wastes such as rice straw, sugar beet, and sugarcane bagasse have become a critical environmental issue due to growing agriculture demand. This study aimed to investigate the valorization possibility of sugarcane bagasse waste for activated carbon preparation. It also aimed to fully characterize the prepared activated carbon (BET surface area) via scanning electron microscope (SEM) and in terms of surface functional groups to give a basic understanding of its structure and to study the adsorption capacity of the sugarcane bagasse-based activated carbon using aqueous methylene blue (MB). The second main objective was to evaluate the performance of sugarcane bagasse-based activated carbon for indoor volatile organic compounds removal using the formaldehyde gas (HCHO) as reference model in two potted plants chambers. The first chamber was labeled the polluted chamber (containing formaldehyde gas without activated carbon) and the second was taken as the treated chamber (containing formaldehyde gas with activated carbon). The results indicated that the sugarcane bagasse-based activated carbon has a moderate BET surface area (557 m 2/g) with total mesoporous volume and microporous volume of 0.310 and 0.273 cm 3/g, respectively. The prepared activated carbon had remarkable adsorption capacity for MB. Formaldehyde removal rate was then found to be more than 67% in the treated chamber with the sugarcane bagasse-based activated carbon. The plants’ responses for this application as dry weight, chlorophyll contents, and protein concentration were also investigated. Implications: Preparation of activated carbon from sugarcane bagasse (SCBAC) is a promising approach to produce cheap and efficient adsorbent for gas pollutants removal. It may be also a solution for the agricultural wastes problems in big cities, particularly in Egypt. MB adsorption tests suggest that the SCBAC have high adsorption capacity. Formaldehyde gas removal in the plant chambers indicates that the SCBAC have potential to recover volatile gases. The results confirmed that the activated carbon produced from sugarcane bagasse waste raw materials can be used as an applicable adsorbent for treating a variety of gas pollutants from the indoor environment. 相似文献
7.
A two-component material (Fe3O4@CaSiO3) with an Fe3O4 magnetite core and layered porous CaSiO3 shell from calcium nitrate and sodium silicate was synthesized by precipitation. The structure, morphology, magnetic properties, and composition of the Fe3O4@CaSiO3 composite were characterized in detail, and its adsorption performance, adsorption kinetics, and recyclability for Cu2+, Ni2+, and Cr3+ adsorption were studied. The Fe3O4@CaSiO3 composite has a 2D core–layer architecture with a cotton-like morphology, specific surface area of 41.56 m2/g, pore size of 16 nm, and pore volume of 0.25 cm3/g. The measured magnetization saturation values of the magnetic composite were 57.1 emu/g. Data of the adsorption of Cu2+, Ni2+, and Cr3+ by Fe3O4@CaSiO3 fitted the Redlich–Peterson and pseudo-second-order models well, and all adsorption processes reached equilibrium within 150 min. The maximum adsorption capacities of Fe3O4@CaSiO3 toward Cu2+, Ni2+, and Cr3+ were 427.10, 391.59, and 371.39 mg/g at an initial concentration of 225 mg/L and a temperature of 293 K according to the fitted curve with the Redlich–Peterson model, respectively. All adsorption were spontaneous endothermic processes featuring an entropy increase, including physisorption, chemisorption, and ion exchange; among these process, chemisorption was the primary mechanism. Fe3O4@CaSiO3 exhibited excellent adsorption, regeneration, and magnetic separation performance, thereby demonstrating its potential applicability to removing heavy metal ions. 相似文献
8.
This study reports the eco-friendly preparation of a novel composite material consisting of red mud and carbon spheres, denoted as red mud@C composite, and its application for the removal of 2,4-dichlorophenoxyacetic acid herbicide (2,4-D) from aqueous solution. The preparation route has a green approach because it follows the low-energy consuming one-step hydrothermal process by using starch as a renewable carbon precursor and red mud as a waste from aluminum production industry. Characterization of the red mud@C composite was performed by FT-IR, TGA, SEM, TEM, BET, XRD, and Raman microscopy analyses. The batch adsorption studies revealed that the red mud@C composite has higher 2,4-D adsorption efficiency than those of the red mud and the naked carbon spheres. The maximum removal at initial pH of 3.0 is explained by considering the pKa of 2,4-D and pH of point of zero charge (pHpzc) of the composite material. The adsorption equilibrium time was 60 min, which followed the pseudo-second-order kinetic model together with intra-particle diffusion model. The isotherm analysis indicated that Freundlich isotherm model better represented the adsorption data, with isotherm parameters of k [15.849 (mg/g) (mg/L)?1/n] and n (2.985). The prepared composite is reusable at least 5 cycles of adsorption-desorption with no significant decrease in the adsorption capacity. 相似文献
9.
Here, we present one of the first studies investigating the mobility, solubility and the speciation-dependent in-situ bioaccumulation of antimony (Sb) in an active Sb mining area (Xikuangshan, China). Total Sb concentrations in soils are high (527-11,798 mg kg −1), and all soils, including those taken from a paddy field and a vegetable garden, show a high bioavailable Sb fraction (6.3-748 mg kg −1), dominated by Sb(V). Elevated concentrations in native plant species (109-4029 mg kg −1) underpin this. Both chemical equilibrium studies and XANES data suggest the presence of Ca[Sb(OH) 6] 2, controlling Sb solubility. A very close relationship was found between the citric acid extractable Sb in plants and water or sulfate extractable Sb in soil, indicating that citric acid extractable Sb content in plants may be a better predictor for bioavailable Sb in soil than total acid digestible Sb plant content. 相似文献
10.
This study aims to synthesize 2-hydroxyethyl acrylate (HEA) and 2-acrylamido-2-methylpropane sulfonic (AMPS) acid-based hydrogels by gamma radiation and to investigate their swelling behavior and heavy metal ion adsorption capabilities. The copolymer hydrogels prepared were characterized via scanning electron microscopy, Fourier transformed infrared spectra, thermal gravimetric analysis, and X-ray photoelectron spectroscopy. The research showed that the copolymer hydrogel was beneficial for permeation due to its porous structure. In addition, the experimental group A-2-d [70 % water volume ratio and ( n (AMPS)/ n (HEA))?=?1:1] was an optimal adsorbent. The optimal pH was 6.0 and the optimal temperature was 15 °C. Pb 2+, Cd 2+, Cu 2+, and Fe 3+ achieved adsorption equilibriums within 24 h, whereas Cr 3+ reached equilibrium in 5 h. Pb 2+, Cd 2+, Cr 3+, and Fe 3+ maximum load capacity was 1,000 mg L ?1, whereas the Cu 2+ maximum capacity was 500 mg L ?1. The priority order in the multicomponent adsorption was Cr 3+>Fe 3+>Cu 2+>Cd 2+>Pb 2+. The adsorption process of the HEA/AMPS copolymer hydrogel for the heavy metal ions was mainly due to chemisorption, and was only partly due to physisorption, according to the pseudo-second-order equation and Langmuir adsorption isotherm analyses. The HEA/AMPS copolymer hydrogel was confirmed to be an effective adsorbent for heavy metal ion adsorption. 相似文献
11.
Background, aim, and scope The pulp and paper industry is the sixth largest polluter discharging a variety of gaseous, liquid, and solid wastes into
the environment. Effluents from bleached Kraft mill effluents (BKME) are polluting waters to a great extent These effluents
cause considerable damage to the receiving waters if discharged untreated since they have high levels of biological oxygen
demand (BOD), chemical oxygen demand (COD), chlorinated compounds (measured as AOX), suspended solids (mainly fibers), fatty
acids, tannins, resin acids, lignin and its derivatives, sulfur and sulfur compounds, etc. This study aimed to remove adsorbed
organic halogen (AOX), total nitrogen, and lignin-degrading products in the wastewater (4,500 m 3/h) from the paper mill in the pulp and paper industry, which is discharged to sea from a plant located in western Turkey.
Materials and methods The photocatalytic degradation of AOX, total nitrogen, and chlorinated lignin in BKME have been investigated in different
parameters, such as time, H 2O 2 and TiO 2 concentration. In addition, for investigating the effect of chlorine on the removal of lignin, pure lignin solution was prepared
in equal amounts to chlorinated lignin degradation products found in BKME. The same experiments were conducted for this solution.
Experiments were carried out in photocatalytic reactor made of Pyrex glass. The mercury lamp was used as a radiation source.
All irradiation was carried out under constant stirring. The existence of dissolved O 2 is an important factor which increases the photocatalytic degradation. Hence, we used an air pump for the aeration of the
wastewater solutions. The temperature of the wastewater was controlled and adjusted to 25°C by thermostat pump in conjunction
with a cooler. At the end of all experiments, AOX, total nitrogen and lignin concentrations were analyzed according to standard
methods. All experiments were performed in duplicate and average values were used.
Results and discussion When the effect of H 2O 2 and time were investigated, it was observed that the AOX concentration increased from 3.0 to 11.0 mg/L by only UV. However,
when H 2O 2 was added, AOX concentration decreased from approximately 3.0 to 0.0 mg/L. The optimal conditions for the removal of AOX
appear to be an initial H 2O 2 concentration of 20.0 mL/L and reaction time of 50 min. In addition, at the same experiment conditions, it was seen that
the total nitrogen concentration decreased from 23.0 to 15.0 mg/L by only UV and by increasing H 2O 2 concentration, the concentration of 20.0 mL/L H 2O 2 appears to be optimal (9.0 mg/L). The AOX, total nitrogen and lignin degradation products and pure lignin go through a minimum
when the concentration of H 2O 2 and TiO 2 increases at constant pH and UV intensity. The kinetics for the degradation of AOX, total nitrogen and lignin degradation
products followed a pseudo-first order law with respect to the products, and the degradation rates (min −1) for the UV/TiO 2/H 2O 2 system were higher than that of the corresponding values for the UV/H 2O 2 system.
Conclusions The AOX, total nitrogen and lignin concentration go through a minimum when the concentration of H 2O 2 and TiO 2 increases at constant pH and UV intensity. It was found that the UV/TiO 2/H 2O 2 system has proved capable of the degradation of total nitrogen as well as chlorinated and degraded lignin in BKME.
Recommendations and perspectives The photocatalytic process can be considered a suitable alternative for the remove of some compounds from the BKME. Nevertheless,
further studies should be carried out to confirm the practical feasibility of BKME. Another result obtained from the study
is that pre-purification carried out with UV/TiO 2/H 2O 2 photocatalytic process may constitute an important step for further purification processes such as adsorption, membrane processes,
etc. 相似文献
12.
A comparative study using native garlic peel and mercerized garlic peel as adsorbents for the removal of Pb 2+ has been proposed. Under the optimized pH, contact time, and adsorbent dosage, the adsorption capacity of garlic peel after mercerization was increased 2.1 times and up to 109.05 mg g ?1. The equilibrium sorption data for both garlic peels fitted well with Langmuir adsorption isotherm, and the adsorbent–adsorbate kinetics followed pseudo-second-order model. These both garlic peels were characterized by elemental analysis, Fourier transform infrared spectrometry (FT-IR), and scanning electron microscopy, and the results indicated that mercerized garlic peel offers more little pores acted as adsorption sites than native garlic peel and has lower polymerization and crystalline and more accessible functional hydroxyl groups, which resulted in higher adsorption capacity than native garlic peel. The FT-IR and X-ray photoelectron spectroscopy analyses of both garlic peels before and after loaded with Pb 2+ further illustrated that lead was adsorbed on the through chelation between Pb 2+ and O atom existed on the surface of garlic peels. These results described above showed that garlic peel after mercerization can be a more attractive adsorbent due to its faster sorption uptake and higher capacity. 相似文献
13.
Plant cell walls may play an important role in the uptake and accumulation of heavy metals. This study was undertaken to obtain a better understanding of the role of the root cell walls (RCW) and their subfractions on adsorption of cadmium (Cd) in a promising woody phytoremediation species, Salix jiangsuensis J172. In order to examine how Cd binding was affected by pectin and hemicellulose, RCW were isolated and sequentially fractioned by removing pectin (RCW1), partial removal of hemicellulose (RCW2), and complete removal of hemicellulose (RCW3). The RCW and fractions were characterized by Fourier transform infrared spectroscopy, which suggested decomposition of hemicellulose and a decline in nitrogen content following cell wall isolation and fractionation. The adsorption affinity of Cd increased gradually following the sequential extraction of root cells, suggesting that hemicellulose negatively impacted Cd adsorption, while pectin and cellulose enhanced Cd adsorption. Cd adsorption dynamics and isotherms could be best described by the pseudo-second-order ( R?>?0.99) and Freundlich ( R?>?0.97) models, respectively. Thermodynamic properties (?G, ?H, and ?S), determined using the van’t Hoff equation, indicated that while Cd adsorption was endothermic, and spontaneous for RCW2 and RCW3, adsorption was not spontaneous for the root, RCW, and RCW1. The results provide evidence for the importance of the root cell walls in the adsorption of Cd by willow roots. 相似文献
14.
Due to its relatively low solubility, mimetite Pb 5(AsO 4) 3Cl may control Pb and As(V) solution levels at a low value in contaminated soils. The time-dependent dissolution of mimetite by low-molecular-weight organic acids (LMWOAs) such as acetic, lactic, citric, and ethylene diamine tetra-acetic acid (EDTA) was determined. At pH 3.5, the presence of citric acid or EDTA significantly increases the solubility of mimetite while acetic or lactic acids show little effect. The effect of all organic anions on the dissolution of mimetite increased with the increase in solution pH. The rate of mimetite dissolution depended on the kind and concentration of organic solvents in the sequence rEDTA > rlactate > racetate > rcitrate. Soluble Pb and As(V) released in LMWOAs and EDTA were higher than the WHO guideline value for these elements in drinking water (10 μg As(V) L −1, 10 μg Pb L −1). This suggests that soil organic acids in rhizosphere can potentially liberate Pb and As(V) from mimetite in contaminated soils. 相似文献
15.
In Brazil, sugarcane fields are often burned to facilitate manual harvesting, and this burning causes environmental pollution from the large amounts of soot released into the atmosphere. This material contains numerous organic compounds such as PAHs. In this study, the concentrations of PAHs in two particulate-matter fractions (PM 2.5 and PM 10) in the city of Araraquara (SE Brazil, with around 200,000 inhabitants and surrounded by sugarcane plantations) were determined during the sugarcane harvest (HV) and non-harvest (NHV) seasons in 2008 and 2009. The sampling strategy included four campaigns, with 60 samples in the NHV season and 220 samples in the HV season. The PM 2.5 and PM 10 fractions were collected using a dichotomous sampler (10 L min ?1, 24 h) with Teflon? filters. The filter sets were extracted (ultrasonic bath with hexane/acetone (1:1 v/v)) and analyzed by HPLC/Fluorescence. The median concentration for total PAHs (PM 2.5 in 2009) was 0.99 ng m ?3 (NHV) and 3.3 ng m ?3 (HV). In the HV season, the total concentration of carcinogenic PAHs (benz(a)anthracene, benzo(b)fluoranthene, benzo(k)fluoranthene, and benzo(a)pyrene) was 5 times higher than in the NHV season. B(a)P median concentrations were 0.017 ng m ?3 and 0.12 ng m ?3 for the NHV and HV seasons, respectively. The potential cancer risk associated with exposure through inhalation of these compounds was estimated based on the benzo[a]pyrene toxic equivalence (BaP eq), where the overall toxicity of a PAH mixture is defined by the concentration of each compound multiplied by its relative toxic equivalence factor (TEF). BaP eq median (2008 and 2009 years) ranged between 0.65 and 1.0 ng m ?3 and 1.2–1.4 ng m ?3 for the NHV and HV seasons, respectively. Considering that the maximum permissible BaP eq in ambient air is 1 ng m ?3, related to the increased carcinogenic risk, our data suggest that the level of human exposure to PAHs in cities surrounded by sugarcane crops where the burning process is used is cause for concern. 相似文献
16.
含羧基(—COOH)的无毒柠檬酸(citric acid, CA)改性木膜(wood membranes, WMs)在水处理领域具有广阔的应用前景。然而,由于木质纤维素的结构特点,—COOH很难引入木膜壁内。对木膜进行不同浓度NaOH的预处理,再与柠檬酸进行酯化反应,用于吸附水中的四环素(tetracycline, TC)。通过碱液预处理,有利于CA与木质纤维素的酯化反应,使得木膜的—COOH含量大幅地提高。TC吸附曲线表明,当碱浓度为6% 以及TC出水浓度为0.5 mg·L −1时,改性木膜的有效过滤体积为1 968 BV(bed volume, BV),比未改性木膜的吸附率提高了约48倍;在4次循环后改性木膜对TC的吸附率也可达97%。当出水浓度为0~0.5 mg·L −1时,水处理成本为0.036 0~0.083 25 元·m −3。因此,改性木膜在去除水中TC方面具有很好的应用前景。以上研究结果可为解决木膜应用中的关键局限性,设计具有环境友好、经济和有效的环境修复膜材料提供参考。 相似文献
17.
Porous carbon is an excellent absorbent for pollutants in water. Here, we report a breakthrough in performance of porous carbon based on lignin prepared using sodium lignosulfonate (SLS), potassium carbonate and melamine as precursor, activator and nitrogen source, respectively. A series of characterization tests confirmed that in-situ nitrogen doping greatly enhanced porous structure, resulting in a specific surface area of 2567.9 m2 g?1 and total pore volume of 1.499 cm3 g?1, which is nearly twice that of non-nitrogen-doped porous carbon. Moreover, adsorption experiments revealed that at 303 K, the saturated adsorption capacity of chloramphenicol was as high as 713.7 mg g?1, corresponding to an improvement of 33.7%. Further, the prepared porous carbon exhibited a strong anti-interference against metal ions and humic acid. The adsorption process was confirmed to be an endothermic reaction dominated by physical adsorption, indicating that an increase in temperature is conducive to adsorption. The results of this study show that nitrogen-doped lignin-based porous carbon prepared by in-situ doping is a promising material to significantly alleviate water pollution owing to its low cost, excellent pore structure and good adsorption properties. 相似文献
18.
Phenanthrene is commonly present together with heavy metals at many contaminated sites. This study investigated the influence of coexisting lead (Pb 2+) or cadmium (Cd 2+) on phenanthrene adsorption on soils. Batch experiments were conducted under different geochemical conditions including pH, mineral structure, organic matter content, and varying amounts of heavy metals. The results showed that the presence of heavy metals in solution at a fixed pH of 5.8 ± 0.1 enhanced phenanthrene adsorption, the extent of which was closely related to the concentrations and the electro-negativity of the metals. The enhancement on phenanthrene adsorption was positively correlated to the amount of adsorbed metals. Although Cd 2+ is a softer Lewis acid, Pb 2+ displayed a more significant effect as it was adsorbed to a greater extent on the soil surfaces. Thus, density of cation accumulation appears to be more influential than metal softness in enhancing phenanthrene adsorption. Moreover, with a portion of organic matter removed by heating at 550 °C, there was a stronger enhancement of phenanthrene adsorption by coexisting Pb 2+, indicating an increasingly dominant mechanisms associated with Pb 2+ at a lower organic matter content. Similar enhancement phenomenon was observed on bentonite and kaolinite, probably resulting from the cation-π bonding between the adsorbed soft metal cations and the aromatic ring of phenanthrene in solution. The desorption experiments further suggested that the bonding of phenanthrene adsorption was strengthened in the presence of Pb 2+ and that a larger proportion of adsorbed phenanthrene remained on the soils (residual fraction) even after sequential methanol extractions. Further spectroscopic analyses and surface characterization are required to provide direct evidence of the formation and relative significance of cation-π bond for phenanthrene adsorption. 相似文献
19.
采用自制木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂R1、R2、R3对二元金属离子Cu2 +/pb2和Zn2+/pb2+溶液中的吸附性能进行了较系统考察.pb2+离子溶液中存在竞争离子Cu2+、Zn2+时,随竞争离子浓度增加,3种吸附树脂R1、R2、R3对pb2+的吸附量明显下降,而竞争离子吸附量显著增加.二元溶液中各金属离子浓度相同时,3种树脂对竞争离子Cu2+、Zn2+的吸附量大于对pb2+的吸附量;各溶液中分别加入NaCl及NaNO3、尿素后,对pb2+离子的吸附量下降迅速.随吸附树脂用量增加,竞争离子Cu2+、Zn2+的吸附量逐渐减小,pb2+的吸附量在吸附树脂用量0.10 g/L(Zn2 +/pb2+溶液)或0.15 g/L(Cu2+/pb2+溶液)时出现最大值.溶液pH值对树脂吸附性能有显著影响.3.0<pH<5.O时,3种树脂对竞争离子和pb2+的吸附量快速增大;5< pH <9时,树脂对竞争离子和pb2+的吸附量基本不变;9<pH<ll时,树脂对pb2+的吸附量减小,而对竞争离子的吸附量或增大或减小. 相似文献
20.
以柠檬酸对荞麦壳进行化学改性,改性后荞麦壳吸附剂对Cu2+的吸附量增加。研究了不同pH、吸附剂投入量、浓度和时间对吸附效果的影响。在pH值为5.5,Cu2+初始浓度50 mg/L,吸附剂投入量为1 g,吸附时间为120 min的条件下,Cu2+的吸附量达到较大值。通过用改性荞麦壳吸附剂对Cu2+的热力学吸附过程的分析,结果表明,改性荞麦壳吸附剂符合Langmuir吸附等温模式,改性荞麦壳吸附剂对Cu2+的吸附存在化学吸附,改性荞麦壳的最大吸附量可以达2.26 mg/g。研究改性荞麦壳吸附剂吸附Cu2+的动力学特性,吸附动力学行为可用准二级速率方程进行很好的描述,准二级吸附速率常数随温度升高而增大。准一级速率方程和颗粒扩散模型可以较好地描述吸附初始阶段,Cu2+浓度较高,颗粒内扩散;吸附后期,Cu2+浓度较低,受到颗粒外扩散的控制。总之,整个吸附过程可能是多种动力学机理共同作用的结果。 相似文献
|