Effectiveness of UV/SO32− advanced reduction process for degradation and mineralization of trichlorfon pesticide in water: identification of intermediates and toxicity assessment

Environmental Science and Pollution Research - This study aimed to investigate the degradability, mineralization, proposed decomposition pathway, intermediate products, and toxicity of effluent...     

Effect of ethylenediamine-N,N′-disuccinic acid on Fenton and photo-Fenton processes using goethite as an iron source: optimization of parameters for bisphenol A degradation

The main disadvantage of using iron mineral in Fenton-like reactions is that the decomposition rate of organic contaminants is slower than in classic Fenton reaction using ferrous ions at acidic pH. In order to overcome these drawbacks of the Fenton process, chelating agents have been used in the investigation of Fenton heterogeneous reaction with some Fe-bearing minerals. In this work, the effect of new iron complexing agent, ethylenediamine-N,N'-disuccinic acid (EDDS), on heterogeneous Fenton and photo-Fenton system using goethite as an iron source was tested at circumneutral pH. Batch experiments including adsorption of EDDS and bisphenol A (BPA) on goethite, H₂O₂ decomposition, dissolved iron measurement, and BPA degradation were conducted. The effects of pH, H₂O₂ concentration, EDDS concentration, and goethite dose were studied, and the production of hydroxyl radical (^?OH) was detected. The addition of EDDS inhibited the heterogeneous Fenton degradation of BPA but also the formation of ^?OH. The presence of EDDS decreases the reactivity of goethite toward H₂O₂ because EDDS adsorbs strongly onto the goethite surface and alters catalytic sites. However, the addition of EDDS can improve the heterogeneous photo-Fenton degradation of BPA through the propagation into homogeneous reaction and formation of photochemically efficient Fe-EDDS complex. The overall effect of EDDS is dependent on the H₂O₂ and EDDS concentrations and pH value. The high performance observed at pH 6.2 could be explained by the ability of O ₂ ^?? to generate Fe(II) species from Fe(III) reduction. Low concentrations of H₂O₂ (0.1 mM) and EDDS (0.1 mM) were required as optimal conditions for complete BPA removal. These findings regarding the capability of EDDS/goethite system to promote heterogeneous photo-Fenton oxidation have important practical implications for water treatment technologies.     

Novel two-step vapor-phase synthesis of UV–Vis light active Fe2O3/WO3 nanocomposites for phenol degradation

Supported Fe₂O₃/WO₃ nanocomposites were fabricated by an original vapor phase approach, involving the chemical vapor deposition (CVD) of Fe₂O₃ on Ti sheets and the subsequent radio frequency (RF)-sputtering of WO₃. Particular attention was dedicated to the control of the W/Fe ratio, in order to tailor the composition of the resulting materials. The target systems were analyzed by the joint use of complementary techniques, that is, X-ray diffraction (XRD), field emission-scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), energy dispersive X-ray spectroscopy (EDXS), X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), and optical absorption spectroscopy. The results showed the uniform decoration of α-Fe₂O₃ (hematite) globular particles by tiny WO₃ aggregates, whose content could be controlled by modulations of the sole sputtering time. The photocatalytic degradation of phenol in the liquid phase was selected as a test reaction for a preliminary investigation of the system behavior in wastewater treatment applications. The system activity under both UV and Vis light illumination may open doors for further material optimization in view of real-world end-uses.

     

Fenton-like oxidation and mineralization of phenol using synthetic Fe(II)–Fe(III) green rusts

Background, aim, and scope  

In literature, the environmental applications of green rust (GR) have mainly been pointed out through the reduction of inorganic contaminants and the reductive dechlorination of chlorinated organics. However, reactions involving GR for the oxidation and mineralization of organic pollutants remain very scantly described. In this study, the ability of three synthetic Fe(II)–Fe(III) green rusts, GR(CO₃²⁻), GR(SO₄²⁻), and GR(Cl⁻), to promote Fenton-like reaction was examined by employing phenol as a model pollutant. Unlike the traditional Fenton’s reagent (dissolved Fe(II) + H₂O₂), where the pH values have to be lowered to less than 4, the proposed reaction can effectively oxidize the organic molecules at neutral pH and could avoid the initial acidification which may be costly and destructive for the in situ remediation of contaminated groundwater and soils. The green rust reactivity towards the oxidative transformation of phenol was thoroughly evaluated by performing a large kinetic study, chemical analyses, and spectroscopic investigations.     

Modeling and optimization of trihalomethanes formation potential of surface water (a drinking water source) using Box–Behnken design

Purpose  

The present research aims to investigate the individual and interactive effects of chlorine dose/dissolved organic carbon ratio, pH, temperature, bromide concentration, and reaction time on trihalomethanes (THMs) formation in surface water (a drinking water source) during disinfection by chlorination in a prototype laboratory-scale simulation and to develop a model for the prediction and optimization of THMs levels in chlorinated water for their effective control.     

Photocatalytic degradation of acetaminophen and caffeine using magnetite–hematite combined nanoparticles: kinetics and mechanisms

Environmental Science and Pollution Research - The increased use of pharmaceutical and personal care products (PPCPs) has contributed to the contamination of water systems and put pressure on the...     

Degrading a mixture of three textile dyes using photo-assisted electrochemical process with BDD anode and O2–diffusion cathode

In this paper, degradation of a mixture of three azo dyes was studied by the photo-assisted electrochemical process using an O₂-diffusion cathode containing carbon nanotubes and boron-doped diamond (BDD) anode. The concentration of three textile dyes (C.I. Acid Orange 8 (AO8), C.I. Acid Orange 10 (AO10), and C.I. Acid Orange 12 (AO12)) was determined simultaneously despite the severe overlap of their spectra. For this purpose, partial least square (PLS), as a multivariate calibration method, was utilized based on recording UV–Vis spectra during the decolorization process. Moreover, the central composite design was used for the modeling of photo-assisted electrochemical decolorization of the aqueous solutions containing three dyes. The investigated parameters were the initial concentration of three dyes, applied current and reaction time. Analysis of variance (ANOVA) revealed that the obtained regression models match the experimental results well with R (Khataee et al. 2010, Clean-Soil Air Water 38 (1):96–103, 2010) of 0.972, 0.971, and 0.957 for AO8, AO10, and AO12, respectively. Three-dimensional surface and contour plots were applied to describe the relation between experimental conditions and the observed response. The results of TOC analysis confirmed good ability of proposed photo-assisted electrochemical process for degradation and mineralization of textile industry wastewater.     

Removal of xylenol orange from its aqueous solution using SDS self-microemulsifying systems: optimization by Box–Behnken statistical design

The aim of present study was to develop and evaluate sodium dodecyl sulfate (SDS) self-microemulsifying systems (SMES) for the removal of an anionic dye xylenol orange (XO) from its bulk aqueous media via liquid–liquid adsorption. The composition of SDS SMES was optimized by Box–Behnken statistical design for the maximum removal of XO from its aqueous solution. Various SDS formulations were prepared by spontaneous emulsification method and characterized for thermodynamic stability, self-microemulsification efficiency, droplet size, and viscosity. Adsorption studies were conducted at 8, 16, and 24 h by mixing small amounts of SDS formulations with relatively large amounts of bulk aqueous solution of XO. Droplet size and viscosity of SDS formulations were significantly influenced by oil phase concentration (triacetin), while surfactant concentration had little impact on droplet size and viscosity. However, the percentage of removal of XO was influenced by triacetin concentration, surfactant concentration, and adsorption time. Based on lowest droplet size (35.97 nm), lowest viscosity (29.62 cp), and highest percentage of removal efficiency (89.77 %), formulation F₁₄, containing 2 % w/w of triacetin and 40 % w/w of surfactant mixture (20 % w/w of SDS and 20 % w/w of polyethylene glycol 400), was selected as an optimized formulation for the removal of XO from its bulk aqueous media after 16 h. These results indicated that SDS SMES could be suitable alternates of solid–liquid adsorption for the removal of toxic dyes such as XO from its aqueous solution through liquid–liquid adsorption.     

Adaptive particle swarm optimization–based deep neural network for productivity enhancement of solar still

Environmental Science and Pollution Research - Water is considered one of the most superabundant resources on the earth that covers 75% of the entire earth’s surface, yet numerous countries...     

Fe(III)–EDDS complex in Fenton and photo-Fenton processes: from the radical formation to the degradation of a target compound

The present work compares the efficiency of homogenous Fenton and photo-Fenton processes in the presence of Fe(III)–EDDS complex under different experimental conditions. 4-tert-Butylphenol (4-t-BP), which is one of the endocrine disrupting chemicals, was used as a model pollutant to investigate the Fenton and photo-Fenton application. The efficiency of homogenous photo-Fenton process was significantly much higher than homogenous Fenton process, which is due to the rapid formation of Fe²⁺ under UV irradiation of the iron complex and the photochemical formation of HO^? from the photolysis of the complex Fe(III)–EDDS. Through the degradation of 4-t-BP, the effect of Fe(III)–EDDS concentration, H₂O₂ concentration, pH, and oxygen was investigated in both processes. Such trend was also correlated with pH calculating the polychromatic Fe²⁺ quantum yield formation at pH 4.0, 6.0, and 8.6. The results showed that at high Fe(III)–EDDS and H₂O₂ concentrations, a negative effect was found. By the way, the Fenton process was found to be enhanced at basic pH. These results can be very useful for the use and optimization of such iron complex in water treatment process as function of different physico-chemical conditions.     

Serum klotho and its associations with blood and urine cadmium and lead across various stages of glomerular function: data for US adults aged 40–79 years

Environmental Science and Pollution Research - Exposures to cadmium and lead can cause oxidative stress, leading to tissue damage resulting in kidney and cardiovascular diseases. The antiaging...     

Carbon dots decorated magnetite nanocomposite obtained using yerba mate useful for remediation of textile wastewater through a photo-Fenton treatment: Ilex paraguariensis as a platform of environmental interest—part 2

Environmental Science and Pollution Research - Two carbon dots (CD) with diameters of 4.9?±?1.5 and 4.1?±?1.2 nm were successfully synthesized through an...     

Development and application of LC–APCI–MS method for biomonitoring of animal and human exposure to imidacloprid

Imidacloprid (IMI) is a relatively new neuro-active neonicotinoid insecticide and nowadays one of the largest selling insecticides worldwide. In the present study a LC–APCI–MS based method was developed and validated for the quantification of imidacloprid and its main metabolite 6-chloronicotinic acid (6-CINA) in urine and hair specimens. The method was tested in biomonitoring of intentionally exposed animals and subsequently applied for biomonitoring of Cretan urban and rural population.     

Process envelopes for stabilisation/solidification of contaminated soil using lime–slag blend

Purpose  

Stabilisation/solidification (S/S) has emerged as an efficient and cost-effective technology for the treatment of contaminated soils. However, the performance of S/S-treated soils is governed by several intercorrelated variables, which complicates the optimisation of the treatment process design. Therefore, it is desirable to develop process envelopes, which define the range of operating variables that result in acceptable performance.     

Separation and remediation of environmental pollutants using metal–organic framework-based tailored materials

Environmental Science and Pollution Research - Metal–organic frameworks (MOFs) are a polymer hybrid family of compounds comprising metal ions that have been deliberately incorporated in...     

Synthesis and optimization of spherical nZVI (20–60 nm) immobilized in bio-apatite-based material for efficient removal of phosphate: Box-Behnken design in a fixed-bed column

In the present study, bio-apatite/nZVI composite was synthesized through Fe(III) reduction with sodium borohydride and was fully characterized by FTIR, XRD, SEM–EDX, TEM, BET, BJH, and pH_PZC. Column experiments were carried out for the removal of phosphate as a function of four operational parameters including initial phosphate concentration (100–200 mg L^?1), initial solution pH (2–9), bed height (2–6 cm), and influent flow rate (2.5–7.5 mL min^?1) using a response surface methodology (RSM) coupled with Box-Behnken design (BBD). 2D contour and 3D surface plots were employed to analyze the interactive effects of the four operating parameters on the column performance (e.g., uptake capacity and saturation time). According to ANOVA analysis, the influent flow rate and bed height are the most important factor on phosphate uptake capacity and saturation time, respectively. A quadratic polynomial model was excellently fitted to experimental data with a high coefficient of determination (>?0.96). The RSM-BBD model predicted maximum phosphate adsorption capacity of 85.71 mg g^?1 with the desirability of 0.995 under the optimal conditions of 135.35 mg L^?1, 2, 2 cm, and 7.5 mL min^?1 for initial phosphate concentration, initial solution pH, bed height, and influent flow rate, respectively. The XRD analysis demonstrated that the reaction product between bio-apatite/nZVI composite and phosphate anions was Fe₃ (PO₄)₂. 8H₂O (vivianite). The suggested adsorbent can be effectively employed up to five fixed-bed adsorption–desorption cycles and was also implemented to adsorb phosphate from real samples.

     

Bioremediation of chlorinated pesticide–contaminated soil using anaerobic sludges and surfactant addition

Methanogenic granular sludge and wastewater fermented sludge were used as inocula for batch tests of anaerobic bioremediation of chlorinated pesticide contaminated soil. Results obtained for both types of biomass were similar: 80 to over 90% of γ -hexachlorocyclohexane (γ-HCH), 1,1,1-trichloro-2,2-bis-(4-methoxyphenyl)ethane (methoxychlor) and 1,1,1-trichloro-2,2-bis-(4-chlorophenyl)ethane (DDT) removed in 4–6 weeks. Residual fractions of these pesticides persisted till the end of the 16-week experiment. DDT was degraded through 1,1-dichloro-2,2-bis-(4-chlorophenyl)ethane (DDD). Accumulation of this product corresponded stoichiometrically only to 34–53% of removed DDT, supposedly due to its further transformations, finally resulting in formation of detected 4,4′-dichlorobenzophenone (DBP). Addition of 0.5 mM Tween 80 nonionic surfactant resulted in about a twofold decrease of γ -HCH and methoxychlor residual concentrations, as well as considerably lower DDD accumulation (7–29%) and higher DBP production. However, 1.25 mM dose of this surfactant applied together with granular sludge brought DDD levels back to that observed for treatments with the sludge alone, also impairing DBP formation.     

UV–visible light-activated Ag-decorated,monodisperse TiO2 aggregates for treatment of the pharmaceutical oxytetracycline

Noble metal Ag-decorated, monodisperse TiO₂ aggregates were successfully synthesized by an ionic strength-assisted, simple sol–gel method and were used for the photocatalytic degradation of the antibiotic oxytetracycline (OTC) under both UV and visible light (UV–visible light) irradiation. The synthesized samples were characterized by X-ray diffraction analysis (XRD); UV–vis diffuse reflectance spectroscopy; environmental scanning electron microscopy (ESEM); transmission electron microscopy (TEM); high-resolution TEM (HR-TEM); micro-Raman, energy-dispersive X-ray spectroscopy (EDS); and inductively coupled plasma optical emission spectrometry (ICP-OES). The results showed that the uniformity of TiO₂ aggregates was finely tuned by the sol–gel method, and Ag was well decorated on the monodisperse TiO₂ aggregates. The absorption of the samples in the visible light region increased with increasing Ag loading that was proportional to the amount of Ag precursor added in the solution over the tested concentration range. The Brunauer, Emmett, and Teller (The BET) surface area slightly decreased with increasing Ag loading on the TiO₂ aggregates. Ag-decorated TiO₂ samples demonstrated enhanced photocatalytic activity for the degradation of OTC under UV–visible light illumination compared to that of pure TiO₂. The sample containing 1.9 wt% Ag showed the highest photocatalytic activity for the degradation of OTC under both UV–visible light and visible light illumination. During the experiments, the detected Ag leaching for the best TiO₂-Ag photocatalyst was much lower than the National Secondary Drinking Water Regulation for Ag limit (0.1 mg L^?1) issued by the US Environmental Protection Agency.     

Rapid photodegradation and detection of zolpidem over β-SnWO4 and α-SnWO4 nanoparticles: optimization and mechanism

Environmental Science and Pollution Research - We reported the tin (II) tungstate nanoparticles as the photocatalyst and sensor modifier that were synthesized via chemical precipitation reaction...