Smokeless Stacks—Industry’s Big Problem

There seems to be a general impression on the part of the public and many technical people that dust collecting systems on the open hearth furnace are simply a matter of giving a contract for a duplicate system to that previously installed; signing a check for a sum to cover the cost of the cleaning equipment itself, pressing the start-up button and then sitting back to receive the plaudits of a grateful community. This paper will briefly present some of the problems common to all of the installations to date. It will also explain why the cost of the cleaning equipment itself is such a small portion of the total cost.     

Matching of an anaerobic animal waste digester with a dual-fuel generator unit

This paper describes a scientific method for matching an anaerobic fermentation digester using animal dung with a diesel engine power-generating unit, in such a way as to specify the digester capacity to be suitable for various specific energy needs. An experimental model consisting of an Indian-type digester connected to a constant speed, single cylinder 3 kW diesel engine, was designed, constructed and tested in the laboratory to obtain a comprehensive understanding of the performance. The engine was operated with dual fuel (biogas and diesel). A performance map was derived to express the ability of the digester to satisfy the different loading conditions of the engine at different mass ratios of the two fuels. Dimensional analysis was carried out to compile the geometric and operating variables of the digester to establish a relation that can be used to demonstrate the effect of the daily loading on the rate of biogas generation using different digester capacities and different proportions of solids in the fermentation material. The study provides the means to match the geometric and dynamic parameters of a digester to specific power requirements within the applied range.     

Improvement of upflow anaerobic sludge bed performance using chitosan.

Chitosan, with a degree of deacetylation of 85% and a molecular weight of 2.5 x 10(5) Da, yielding high flocculation efficiency (85 to 100% flocculation) and a broad flocculation region (2 to 45 mg/g suspended solids), was selected for accelerating granulation in a 30-L upflow anaerobic sludge bed (UASB) used to treat wastewater from a tropical fruit-processing industry. Compared with other studies, smaller amounts of chitosan were applied (two injections with 2 mg chitosan/g suspended solids in the reactor at each injection). Comparison with the UASB without chitosan addition, the UASB had a 24 to 37% larger particle size and a 6 to 41% longer solids retention time. In addition, the reactor performances were also enhanced. The UASB with chitosan addition had a 9 to 59% lower effluent chemical oxygen demand (COD), 4 to 10% higher COD removal, up to 35% higher biogas production rate, and a 16 to 68% lower biomass washout. The paired t-test analysis indicated that these performance parameters were significantly different (P < 0.05).     

A simple model which predicts some non-linear features between atmospheric sulphur and sulphur emissions

This paper develops a simple model and suggests a plausible chemico-physical mechanism for a non-linear response between atmospheric sulphur and sulphur emissions. It contains simplified representations of transport, deposition and conversion processes and uses a proxy in-cloud oxidant-limited reaction along a pathway connecting an emission source with a receptor site. Individual pathway responses to emissions show linear behaviour above a threshold. However, by averaging the values of SO2 at the receptor site from different pathways a continuous non-linear relationship is obtained. As emissions reduce, distant emission sources become less significant contributors of sulphur dioxide at a receptor site but their emissions are still counted in an emission inventory, leading to an apparent non-linearity. Sulphate is always found to contribute a signal to the receptor site total. This model goes someway to explaining a proposed 'crossover' between observed proportions of wet and dry deposited sulphur in the UK as emissions have been reduced.     

A study on the characteristics of silt loading on paved roads in the Seoul metropolitan area using a mobile monitoring system

This study is considered the first attempt to apply a mobile monitoring system to estimating silt loading on paved roads in a mega-city such as the Seoul metropolitan area. Using a mobile monitoring system developed in 2005, we estimated silt loadings on representative paved roads in the Seoul metropolitan area, including the city of Incheon, over a period of 3 yr. The temporal and spatial characteristics of silt loading were investigated for the carefully selected roads that may reflect the characteristics of the cities of Seoul and Incheon. In this study, changes in the average silt loading values were investigated in terms of land use, the temporal resolution of data acquisition (i.e., seasonal, daily, three-hour scale), the road width or number of lanes, and rainfall, which may affect the characteristics of the average silt loading significantly. It was found that the advantages of using the mobile monitoring system are its ability to obtain a large quantity of silt loading data in a short period of time and over a wide area and its ability to create a silt loading map showing the relative magnitude of silt loading in relation to a specific location, which makes it possible to easily locate hot spots.

Implications: This study may be considered the first practical application of a mobile monitoring system to obtain the silt loading data on paved roads in a mega-city such as Seoul. It was found that the advantages of using the mobile monitoring system are its ability to obtain a large quantity of silt loading data in a short period of time and over a wide area and its ability to create a silt loading map showing the relative magnitude of silt loading in relation to a specific location, which makes it possible to easily locate hot spots to be cleaned cost-effectively by city officials.     

US Army Chemical Corps Vietnam veterans health study: preliminary results

The long-term health consequences of exposure to phenoxyherbicides used in Vietnam has been a great concern to the veterans. In addition to the Air Force Ranch Hand personnel, Army Chemical Corps personnel who served in Vietnam are thought to have had some of the highest herbicide exposures. The Department of Veterans Affairs commenced a study of veterans who served in Vietnam as members of the Army Chemical Corps and a comparison cohort of Army Chemical Corps personnel who served elsewhere. A total of 2872 Vietnam veterans and 2737 non-Vietnam veterans who served in the Army Chemical Corps were identified for inclusion in a telephone health interview survey with a random 20% sample of veterans receiving serum dioxin and other congeners assessments. In a feasibility study which included 284 Vietnam veterans and 281 non-Vietnam veterans, 100 serum assessments were conducted of which 95 were included in the analysis. Vietnam veterans with a history of spraying herbicides were found to have a statistically significant elevation in their current serum 2,3,7,8-TCDD concentrations compared to non-Vietnam veterans without a spray history (P = 0.05). Other 2,3,7,8-substituted dioxins levels were comparable to the levels found in the non-Vietnam veterans. This feasibility study demonstrated that serum dioxin concentrations from a sample of the study participants can be used to identify exposure variables in the health survey that can serve as a surrogate measure of phenoxyherbicide exposure.     

International cross-validation of a BOD5 surrogate

BOD5 dates back to 1912 when the Royal Commission decided to use the mean residence time of water in the rivers of England, 5 days, as a standard to measure the biochemical oxygen demand. Initially designed to protect the quality of river waters from extensive sewage discharge, the use of BOD5 has been quickly extended to waste water treatment plants (WWTPs) to monitor their efficiency on a daily basis. The measurement has been automatized but remains a tedious, time- and resource-consuming analysis. We have cross-validated a surrogate BOD5 method on two sites in France and in the USA with a total of 109 samples. This method uses a fluorescent redox indicator on a 96-well microplate to measure microbial catabolic activity for a large number of samples simultaneously. Three statistical tests were used to compare surrogate and reference methods and showed robust equivalence.     

Effect of aggregate storage piles configuration on dust emissions

Fugitive dust emissions from stockpiles in the open storage yards of industrial sites and the subsequent atmospheric dust dispersion have brought about many ecological and economical problems. This paper introduces a new approach to estimate emission rates using data from Computational Fluid Dynamics simulations. Flow around stockpiles of varying configurations was studied using a previously validated numerical model. Different pile height scenarios, corresponding to a constant material volume and a fixed angle of repose, were exposed to various wind speeds. Flow analysis over the piles showed the importance of using 3D simulations to fully understand the close linkage between flow processes and particles uptake. Data obtained were then integrated in order to evaluate dust emission rates. Results provide evidence to suggest that changing pile configuration can reduce dust emissions. It was found that, for the range of wind conditions and pile dimensions tested, the intermediate pile height configurations lead to a better overall protecting effect from wind and thus were found to produce lower dust emissions.     

Sustainable development and the worldwide market economy: a necessary but difficult reconciliation

The only satisfactory concept of development is a global one, of which the usual notion of sustainable development is only a part. The only economic system providing efficiency is the market, with a high level of responsibility given to decentralised and autonomous decision-makers. However, the market economy does not automatically generate globally desirable development. It has to be complemented by public intervention, leading in a single country to a mixed economy, and in a world-set of countries to international agreements, creating two kinds of international order, at two levels: very restrictive between countries with common basic political and social values, and provisionally more flexible and concerning only few very fundamental topics at a world-wide level.     

Aggregate Source-receptor Relations for Economic Analysis of Ambient Regulations

The purpose of this paper is to describe a new approach for determining the relationship between aggregate pollutant emissions and ambient concentrations in an air basin. The approach is to use a detailed meteorological model to generate a large set of pseudodata on specific source-receptor relationships. This data is then statistically reduced to a simple relationship between aggregate emissions and pollution concentration averages or maxima. In the paper, we give a justification for the approach and an empirical application to the Petrified Forest region of Arizona.     

Risk assessment and prioritisation of contaminated sites on the catchment scale

Contaminated sites pose a significant threat to groundwater resources worldwide. Due to limited available resources a risk-based prioritisation of the remediation efforts is essential. Existing risk assessment tools are unsuitable for this purpose, because they consider each contaminated site separately and on a local scale, which makes it difficult to compare the impact from different sites. Hence a modelling tool for risk assessment of contaminated sites on the catchment scale has been developed. The CatchRisk screening tool evaluates the risk associated with each site in terms of its ability to contaminate abstracted groundwater in the catchment. The tool considers both the local scale and the catchment scale. At the local scale, a flexible, site specific leaching model that can be adjusted to the actual data availability is used to estimate the mass flux over time from identified sites. At the catchment scale, a transport model that utilises the source flux and a groundwater model covering the catchment is used to estimate the transient impact on the supply well. The CatchRisk model was tested on a groundwater catchment for a waterworks north of Copenhagen, Denmark. Even though data scarcity limited the application of the model, the sites that most likely caused the observed contamination at the waterworks were identified. The method was found to be valuable as a basis for prioritising point sources according to their impact on groundwater quality. The tool can also be used as a framework for testing hypotheses on the origin of contamination in the catchment and for identification of unknown contaminant sources.     

The integrated biomarker response revisited: optimization to avoid misuse

The growing need to evaluate the quality of aquatic ecosystems led to the development of numerous monitoring tools. Among them, the development of biomarker-based procedures, that combine precocity and relevance, is recommended. However, multi-biomarker approaches are often hard to interpret, and produce results that are not easy to integrate in the environmental policies framework. Integrative index have been developed, and one of the most used is the integrated biomarker response (IBR). However, an analysis of available literature demonstrated that the IBR suffers from a frequent misuse and a bias in its calculation. Then, we propose here a new calculation method based on both a more simple formula and a permutation procedure. Together, these improvements should rightly avoid the misuse and bias that were recorded. Additionally, a case study illustrates how the new procedure enabled to perform a reliable classification of site along a pollution gradient based on biomarker responses used in the IBR calculations.     

An analytical solution for vertical transport of volatile chemicals in the vadose zone

An analytical solution is presented for one-dimensional vertical transport of volatile chemicals through the vadose zone to groundwater. The solution accounts for the important transport mechanisms of the steady advection of water and gas, diffusion and dispersion in water and gas, as well as adsorption, and first-order degradation. By assuming a linear, equilibrium partitioning between water, gas and the adsorbed chemical phases, the dependent variable in the mathematical model becomes the total resident concentration. The general solution was derived for cases having a constant initial total concentration over a discrete depth interval and a zero initial total concentration elsewhere. A zero concentration gradient is assumed at the groundwater table. Examples are given to demonstrate the application of the new solution for calculating the case of a non-uniform initial source concentration, and estimating the transport of chemicals to the groundwater and the atmosphere. The solution was also used to verify a numerical code called VLEACH. We discovered an error in VLEACH, and found that the new solution agreed very well with the numerical results by corrected VLEACH. A simplified solution to predict the migration of volatile organic chemical due to the gas density effect has shown that a high source concentration may lead to significant downward advective gas-phase transport in a soil with a high air-permeability.     

A multiple testing approach for hazard evaluation of complex mixtures in the aquatic environment: the use of diesel oil as a model

Traditional single species toxicity tests and multiple component laboratory-scaled microcosm assays were combined to assess the toxicological hazard of diesel oil, a model complex mixture, to a model aquatic environment. The immediate impact of diesel oil dosed on a freshwater community was studied in a model pond microcosm over 14 days: a 7-day dosage and a 7-day recovery period. A multicomponent laboratory microcosm was designed to monitor the biological effects of diesel oil (1.0 mg litre(-1)) on four components: water, sediment (soil + microbiota), plants (aquatic macrophytes and algae), and animals (zooplanktonic and zoobenthic invertebrates). To determine the sensitivity of each part of the community to diesel oil contamination and how this model community recovered when the oil dissipated, limnological, toxicological, and microbiological variables were considered. Our model revealed these significant occurrences during the spill period: first, a community production and respiration perturbation, characterized in the water column by a decrease in dissolved oxygen and redox potential and a concomitant increase in alkalinity and conductivity; second, marked changes in microbiota of sediments that included bacterial heterotrophic dominance and a high heterotrophic index (0.6), increased bacterial productivity, and the marked increases in numbers of saprophytic bacteria (10 x) and bacterial oil degraders (1000 x); and third, column water acutely toxic (100% mortality) to two model taxa: Selenastrum capricornutum and Daphnia magna. Following the simulated clean-up procedure to remove the oil slick, the recovery period of this freshwater microcosm was characterized by a return to control values. This experimental design emphasized monitoring toxicological responses in aquatic microcosm; hence, we proposed the term 'toxicosm' to describe this approach to aquatic toxicological hazard evaluation. The toxicosm as a valuable toxicological tool for screening aquatic contaminants was demonstrated using diesel oil as a model complex mixture.     

Stratospheric ozone depletion, UV-B radiation and crop disease

Ultraviolet-B radiation (UV-B: 290-315 nm) is expected to increase as the result of stratospheric ozone depletion. Within the environmental range, UV-B effects on host plants appear to be largely a function of photomorphogenic responses, while effects on fungal pathogens may include both photomorphogenesis and damage. The effects of increased UV-B on plant-pathogen interactions has been studied in only a few pathosystems, and have used a wide range of techniques, making generalisations difficult. Increased UV-B after inoculation tends to reduce disease, perhaps due to direct damage to the pathogen, although responses vary markedly between and within pathogen species. Using Septoria tritici infection of wheat as a model system, it is suggested that even in a species that is inherently sensitive to UV-B, the effects of ozone depletion in the field are likely to be small compared with the effects of variation in UV-B due to season and varying cloud. Increased UV-B before inoculation causes a range of effects in different systems, but an increase in subsequent disease is a common response, perhaps due to changes in host surface properties or chemical composition. Although it seems unlikely that most crop diseases will be greatly affected by stratospheric ozone depletion within the limits currently expected, the lack of a detailed understanding of the mechanisms by which UV-B influences plant-pathogen interactions in most pathosystems is a significant limit to such predictions.     

Nature and COVID-19: The pandemic,the environment,and the way ahead

The COVID-19 pandemic has brought profound social, political, economic, and environmental challenges to the world. The virus may have emerged from wildlife reservoirs linked to environmental disruption, was transmitted to humans via the wildlife trade, and its spread was facilitated by economic globalization. The pandemic arrived at a time when wildfires, high temperatures, floods, and storms amplified human suffering. These challenges call for a powerful response to COVID-19 that addresses social and economic development, climate change, and biodiversity together, offering an opportunity to bring transformational change to the structure and functioning of the global economy. This biodefense can include a “One Health” approach in all relevant sectors; a greener approach to agriculture that minimizes greenhouse gas emissions and leads to healthier diets; sustainable forms of energy; more effective international environmental agreements; post-COVID development that is equitable and sustainable; and nature-compatible international trade. Restoring and enhancing protected areas as part of devoting 50% of the planet’s land to environmentally sound management that conserves biodiversity would also support adaptation to climate change and limit human contact with zoonotic pathogens. The essential links between human health and well-being, biodiversity, and climate change could inspire a new generation of innovators to provide green solutions to enable humans to live in a healthy balance with nature leading to a long-term resilient future.     

Optimization of the intermittent aeration in a full-scale wastewater treatment plant biological reactor for nitrogen removal.

The optimization of the intermittent aeration in a full-scale biological reactor treating municipal and industrial wastewater has been studied by means of an experimental design, where the main factors considered have been the on-off period of aeration and the dissolved-oxygen set point. The objective of the work has been to determine the optimal configuration of the aeration control to achieve a simultaneous removal of carbon (expressed as chemical oxygen demand [COD]) and nitrogen. The results were obtained in a full-scale bioreactor located at the wastewater treatment plant of Sant Celoni (Barcelona, Spain), where a nitrogen removal based on a nitrification-denitrification process is being tested. It has been shown that the crucial parameter to ensure a complete removal of COD and nitrogen is to give the system a long time of on-off aeration to complete both the nitrification and the denitrification processes, whereas the dissolved-oxygen set point has a minor influence on the overall performance. The results presented can be applied to a great number of similar systems, in which a nitrogen removal, based on a nitrification-denitrification scheme, is currently being tested or implemented.     

Characterizing sources of nitrate leaching from an irrigated dairy farm in Merced County, California

Dairy farms comprise a complex landscape of groundwater pollution sources. The objective of our work is to develop a method to quantify nitrate leaching to shallow groundwater from different management units at dairy farms. Total nitrate loads are determined by the sequential calibration of a sub-regional scale and a farm-scale three-dimensional groundwater flow and transport model using observations at different spatial scales. These observations include local measurements of groundwater heads and nitrate concentrations in an extensive monitoring well network, providing data at a scale of a few meters and measurements of discharge rates and nitrate concentrations in a tile-drain network, providing data integrated across multiple farms. The various measurement scales are different from the spatial scales of the calibration parameters, which are the recharge and nitrogen leaching rates from individual management units. The calibration procedure offers a conceptual framework for using field measurements at different spatial scales to estimate recharge N concentrations at the management unit scale. It provides a map of spatially varying dairy farming impact on groundwater nitrogen. The method is applied to a dairy farm located in a relatively vulnerable hydrogeologic region in California. Potential sources within the dairy farm are divided into three categories, representing different manure management units: animal exercise yards and feeding areas (corrals), liquid manure holding ponds, and manure irrigated forage fields. Estimated average nitrogen leaching is 872 kg/ha/year, 807 kg/ha/year and 486 kg/ha/year for corrals, ponds and fields respectively. Results are applied to evaluate the accuracy of nitrogen mass balances often used by regulatory agencies to assess groundwater impacts. Calibrated leaching rates compare favorably to field and farm scale nitrogen mass balances. These data and interpretations provide a basis for developing improved management strategies.     

Satisfaction with fishing and the desire to leave

Predicting who may leave a fishery is an important consideration when designing capacity reduction programs to enhance both ecological and economic sustainability. In this paper, the relationship between satisfaction and the desire to exit a fishery is examined for the Queensland East Coast Trawl fishery. Income from fishing, and changes in income over the last 5 years, were key factors affecting overall satisfaction. Relative income per se was not a significant factor, counter to most satisfaction studies. Continuing a family tradition of fishing and, for one group, pride in being a fisher was found to be significant. Satisfaction with fishing overall and the challenge of fishing were found to be the primary drivers of the desire to stay or leave the fishery. Surprisingly, public perceptions of fishing, trust in management and perceptions of equity in resource allocation did not significantly affect overall satisfaction or the desire to exit the fishery.     

Uranium bioaccumulation and biological disorders induced in zebrafish (Danio rerio) after a depleted uranium waterborne exposure

Because of its toxicity and its ubiquity within aquatic compartments, uranium (U) represents a significant hazard to aquatic species such as fish. In a previous study, we investigated some biological responses in zebrafish either exposed to depleted or to enriched U (i.e., to different radiological activities). However, results required further experiments to better understand biological responses. Moreover, we failed to clearly demonstrate a significant relationship between biological effects and U radiological activity. We therefore chose to herein examine U bioaccumulation and induced effects in zebrafish according to a chemical dose-response approach. Results showed that U is highly bioconcentrated in fish, according to a time- and concentration-dependent model. Additionally, hepatic antioxidant defenses, red blood cells DNA integrity and brain acetylcholinesterase activity were found to be significantly altered. Generally, the higher the U concentration, the sooner and/or the greater the effect, suggesting a close relationship between accumulation and effect.