Persulfate mediated solar photo-Fenton aiming at wastewater treatment plant effluent improvement at neutral PH: emerging contaminant removal,disinfection, and elimination of antibiotic-resistant bacteria

Environmental Science and Pollution Research - This work investigated an innovative alternative to improve municipal wastewater treatment plant effluent (MWWTP effluent) quality aiming at the...     

城市污水处理厂反硝化聚磷菌的聚磷持久性

以桂林市第四污水处理厂氧化沟活性污泥为对象,研究在具有厌氧-缺氧-好氧环境的污水处理构筑物中富集存在的反硝化聚磷菌聚磷能力的持久性问题。结果表明,在此环境中富集的反硝化聚磷菌在经过3个周期的厌氧-缺氧条件下运行,最大释磷率由0.90 mg P/（g VSS.h）下降为0.07 mg P/（g VSS.h）,反硝化聚磷率由0.17 mg P/（g VSS.h）下降为0.04 mg P/（g VSS.h）。比较而言,在厌氧-缺氧-好氧环境下最大释磷率及聚磷率降幅较小,释磷率由0.59 mg P/（gVSS.h）下降为0.37 mg P/（g VSS.h）,反硝化聚磷率由0.17 mg P/（g VSS.h）下降为0.10 mg P/（g VSS.h）,厌氧-缺氧-好氧运行条件比单纯的厌氧-缺氧运行条件更有利于维持反硝化聚磷菌的聚磷性能。     

Hydrodynamic treatment of wastewater effluent flocs for improved disinfection

Hydrodynamic forces generated by an orifice plate under low pressure were examined as a means of disrupting flocs, in order to improve disinfection of treated wastewater effluents. Changes in cavitation conditions were found to have little impact on the extent of particle breakage in this experimental setup. The rate of strain (flow rate divided by the hole radius cubed), however, was found to be the best predictor of floc breakage. Floc breakage was not affected by changes in floc concentration, but was very sensitive to differences between flocs collected from different sources. Larger flocs (90 to 106 microm) were broken apart to a greater extent than smaller ones (53 to 63 microm). Hydrodynamic treatment decreased the viability of bacteria associated with large flocs, and also increased the ultraviolet dose response by up to one log unit (i.e., a factor of ten). Subjecting final effluent wastewaters to hydrodynamic treatment, therefore, provides a treatment strategy for conditions in which the presence of flocs limits the level of disinfection that can be achieved.     

Occurrence of pharmaceuticals in a municipal wastewater treatment plant: mass balance and removal processes

Occurrence and removal efficiencies of fifteen pharmaceuticals were investigated in a conventional municipal wastewater treatment plant in Michigan. Concentrations of these pharmaceuticals were determined in both wastewater and sludge phases by a high-performance liquid chromatograph coupled to a tandem mass spectrometer. Detailed mass balance analysis was conducted during the whole treatment process to evaluate the contributing processes for pharmaceutical removal. Among the pharmaceuticals studied, demeclocycline, sulfamerazine, erythromycin and tylosin were not detected in the wastewater treatment plant influent. Other target pharmaceuticals detected in wastewater were also found in the corresponding sludge phase. The removal efficiencies of chlortetracycline, tetracycline, sulfamerazine, acetaminophen and caffeine were >99%, while doxycycline, oxytetracycline, sulfadiazine and lincomycin exhibited relatively lower removal efficiencies (e.g., <50%). For sulfamethoxazole, the removal efficiency was approximately 90%. Carbamazepine manifested a net increase of mass, i.e. 41% more than the input from the influent. Based on the mass balance analysis, biotransformation is believed to be the predominant process responsible for the removal of pharmaceuticals (22% to 99%), whereas contribution of sorption to sludge was relatively insignificant (7%) for the investigated pharmaceuticals.     

Application of molecularly imprinted and non-imprinted polymers for removal of emerging contaminants in water and wastewater treatment: a review

Over the past decade, several studies have reported trace levels of endocrine disrupting compounds, pharmaceuticals, and personal care products in surface waters, drinking water, and wastewater effluents. There has also been an increased concern about the ecological and human health impact of these contaminants, and their removal from water and wastewater has become a priority. Traditional treatment processes are limited in their ability to remove emerging contaminants from water, and there is a need for new technologies that are effective and feasible. This paper presents a review on recent research results on molecularly imprinted (MIP) and non-imprinted (NIP) polymers and evaluates their potential as a treatment method for the removal of emerging contaminants from water and wastewater. It also discusses the relative benefits and limitations of using MIP or NIP for water and wastewater treatment. MIP, and in particular NIP, offer promising applications for wastewater treatment, but their toxicity and possible health effects should be carefully studied before they are considered for drinking water treatment. More research is also required to determine how best to incorporate MIP and NIP in treatment plants.     

微絮凝-直接过滤工艺在城市污水深度处理中的应用研究

微絮凝 -直接过滤工艺是一种将混凝反应、沉淀截留集中在同一滤柱内同步完成的高效水处理工艺。该工艺应用于城市污水的深度处理中 ,通过絮凝剂的加入 ,具有同步去除PO3 -4 P、SS和部分COD的功能。本文研究了该工艺对二级处理出水中PO3 -4 P、SS和COD的去除效果及其规律。研究表明 :采用聚合氯化铁 (PFC)作为絮凝剂 ,当Fe/P摩尔比为 2∶1时 ,水中PO3 -4 P的去除率达 98.8% ,浓度可降至 0 .1mg/L以下 ,同时SS、COD去除率也有明显提高。与传统的混凝、沉淀除磷工艺相比 ,该工艺具有操作简单、结构紧凑、占地面积小、污泥量少等优点 ,是一种更为经济和简单的处理单元 ,适用于现有城市污水处理厂的除磷和进一步提高水质的深度处理     

LED irradiated photo-Fenton for the removal of estrogenic activity and endocrine disruptors from wastewater treatment plant effluent

Environmental Science and Pollution Research - The goal of this work was to evaluate the performance of the LED irradiated photo-Fenton process on the removal of (i) estrogenic activity and (ii)...     

膜生物反应器工艺污水处理厂设计进水水质的确定

城市污水处理厂进水水质是工程设计的基本参数,进水水质的测定分析对污水处理厂的设计具有重要意义。对无锡市城北污水处理厂的现状进水水质进行了调查和分析,提出按照水质指标浓度出现的频率确定污水处理厂设计进水水质的方法,并针对采用的膜生物反应器(MBR)工艺的特点,提出:(1)根据实测数据按照一定的保证概率可以用来确定城市污水处理厂设计进水水质;(2)为了使水质的确定更加符合设计工程的实际情况,根据实测数据分析确定设计进水水质指标时,一般还需要进行趋势性调整和季节性调整;(3)确定合理的指标浓度与流量,以此为依据进行反应池的工艺设计,同时要校核夏季温度高、浓度低、流量大和冬季温度低、浓度高、流量小的工况是否满足处理要求,然后取冬、夏季校核值以及未作季节性调整设计值中最不利情况作为设计值,才能充分保证出水达到处理要求。     

城市污水厂污水污泥的热值测定分析方法研究

建立热力学指标是污水生物处理过程热力学分析的基础工作,目前仍缺乏污水污泥化学能测试的标准方法。采用IKA C5000型自动热量计对某城市二级污水处理厂进水、出水、初沉污泥、剩余污泥、混合污泥和脱水污泥进行了热值测定,样品前处理采用103～105℃烘干获得干燥基,用苯甲酸进行加标回收。参照煤的发热量测定方法得到样品的高位热值。试验结果显示：出水干燥基的热值为05 kJ/g,进水干燥基的热值为4 kJ/g以上,各工艺段的污泥干燥基热值较高,基本都在12 kJ/g以上,接近右江褐煤水平。测定结果的标准偏差≤±0.452%,相对标准偏差≤±0.136%。通过同一批样品的元素分析及Dulong公式理论推算,发现2种方法可得到相似的结果。     

瓜环对污水厂二级处理出水中有机污染物的混凝性能

采用扫描电子显微镜和傅里叶红外光谱技术考察了瓜环的物化性能,以及溶液pH和瓜环投加量对其混凝效果的影响。结果表明,盐酸对瓜环的助溶效果最佳,混凝后絮体颗粒呈密实的团状。红外光谱中无新吸收峰出现,说明瓜环与污水中有机物的混凝去除以物理作用为主,无化学键的形成。当投药量大于400 mg/L时,瓜环对初始有机物浓度为6.0 mg/L和9.2 mg/L的污水厂二级处理出水的TOC去除率分别在20%和25%以上。与明矾和聚合氯化铝等传统混凝剂相比,瓜环的混凝性能明显优于传统混凝剂且受pH值的影响较小,作为新型水处理材料具有一定的研究价值和应用前景。     

微生物絮凝剂与聚合氯化铝复配处理污水厂二级出水

探讨了微生物絮凝剂处理二级出水过程中投加量和pH值对溶解性有机碳和浊度处理效果的影响,及将微生物絮凝剂与聚合氯化铝按不同比例复配后的去除效果及pH值对最佳投药量下去除效果的影响。并使用三维荧光光谱（3DEEM）分析了不同种类的絮凝剂在去除水中溶解性有机物（DOM）时的差别。实验结果表明：微生物絮凝剂的最佳投药量为20 mg·L-1,最适pH值为7.5,此时TOC去除率为17%,浊度去除率为45%。最佳复配投药量为微生物絮凝剂10 mg·L-1聚合氯化铝20 mg·L-1,最适pH值为7,此时TOC去除率为33%,浊度去除率为51%。复配使用对腐殖质有很好的去除效果。     

浊度与微生物指标在污水再生处理系统中的去除特性及相关性

本研究考察了污水再生处理系统对颗粒物（包括浊度和粒径分布）和微生物指标（包括隐孢子虫、贾第鞭毛虫、粪大肠菌群和SC噬菌体）的去除特性以及不同指标间的相关关系。研究结果表明,污水再生处理系统对浊度的平均去除率为3.53-log,其中二级生化处理及砂滤对浊度的去除率较高,分别为1.52-log和1.35-log。粒径分析结果表明,絮凝沉淀后粒径均值达到最大值223.2 μm;而再生水中粒径均值最小,仅为5.8 μm。污水再生处理系统对各微生物指标的去除率为2.96-log~4.11-log。各处理单元中,二级生化处理单元对粪大肠菌群和SC噬菌体的去除率较高,分别为2.81-log及2.14-log;而砂滤对SC噬菌体去除效果较差,仅为0.18-log。从再生处理工艺整体上看,水样浊度、粪大肠菌群、SC噬菌体和两虫浓度具有显著相关性。而对于单个取样点,除污水厂进水中 SC噬菌体和两虫浓度表现出一定相关性外,其他情况下各指标与两虫浓度间均无显著相关关系。     

城市污水处理厂恶臭污染源调查与研究

以H2S和NH3为主要监测指标,对广州一大型生活污水处理厂主要恶臭源H2S、NH3的排放浓度进行了8个月的连续监测.结果表明,该污水厂恶臭成分H:S的排放浓度为0.01-22 mg/m',NH,排放浓度为0～0.67 mg/m3.同时,污水厂各处理单元由于其功能和运行条件不同,所产生的恶臭气体成分也不完全一样,在污水进水区段恶臭污染物以H2S为主,其中格栅井H2S浓度最高.其中沉砂池、格栅和污泥浓缩池的H2S、NH3排放浓度呈夏秋季节高、冬春季节低的特征,与季节变化的气温有明显的相关性.对恶臭排放影响因素的研究表明,污水水温越低则H2S和NH3的排放浓度越低,此外,降雨可以显著降低污水处理厂恶臭污染物的排放浓度.     

Coagulant recovery from water treatment plant sludge and reuse in post-treatment of UASB reactor effluent treating municipal wastewater

In the present study, feasibility of recovering the coagulant from water treatment plant sludge with sulphuric acid and reusing it in post-treatment of upflow anaerobic sludge blanket (UASB) reactor effluent treating municipal wastewater were studied. The optimum conditions for coagulant recovery from water treatment plant sludge were investigated using response surface methodology (RSM). Sludge obtained from plants that use polyaluminium chloride (PACl) and alum coagulant was utilised for the study. Effect of three variables, pH, solid content and mixing time was studied using a Box–Behnken statistical experimental design. RSM model was developed based on the experimental aluminium recovery, and the response plots were developed. Results of the study showed significant effects of all the three variables and their interactions in the recovery process. The optimum aluminium recovery of 73.26 and 62.73 % from PACl sludge and alum sludge, respectively, was obtained at pH of 2.0, solid content of 0.5 % and mixing time of 30 min. The recovered coagulant solution had elevated concentrations of certain metals and chemical oxygen demand (COD) which raised concern about its reuse potential in water treatment. Hence, the coagulant recovered from PACl sludge was reused as coagulant for post-treatment of UASB reactor effluent treating municipal wastewater. The recovered coagulant gave 71 % COD, 80 % turbidity, 89 % phosphate, 77 % suspended solids and 99.5 % total coliform removal at 25 mg Al/L. Fresh PACl also gave similar performance but at higher dose of 40 mg Al/L. The results suggest that coagulant can be recovered from water treatment plant sludge and can be used to treat UASB reactor effluent treating municipal wastewater which can reduce the consumption of fresh coagulant in wastewater treatment.     

Effects of activated sludge and UV disinfection processes on the bacterial community and antibiotic resistance profile in a municipal wastewater treatment plant

Environmental Science and Pollution Research - Wastewater tertiary treatment has been pointed out as an effective alternative for reducing the concentration of antibiotic resistant bacteria and...     

污水处理厂除臭工艺选择及工程设计

随着无锡市城北污水处理厂二期工程的扩建,污水处理厂除臭问题日益突出.针对目前常用的化学、活性炭吸附、氧离子基团、燃烧、纯天然植物提取液喷洒和生物等6种除臭方法,重点说明了除臭工艺的选择及除臭系统的工程设计,最后结合运行情况总结了除臭系统的设计特点.     

城市污水厂污泥化学调理深度脱水机理

城市污水厂剩余污泥脱水是当前实际生产中亟待解决的问题。考察了厦门市集美污水厂剩余污泥经FeCl3和CaO,投加量分别为污泥质量分数的0.5%～0.7%和1.0%～1.5%化学调理前后污泥粒度、形态及胞外聚合物(extracellular polymeric substances,EPS)的变化。结果表明,调理后污泥比阻降低86%,污泥颗粒之间细碎紧密,细菌表面变得粗糙,经板框压滤后含水率低于60%。由三维荧光光谱(three-dimensional emission and excitation matrixs,EEM)光谱分析可知,LB-EPS(loosely bound-EPS)同TB-EPS(Tightly bound-EPS)的荧光峰整体发生红移,出现位于IV区域的色氨酸类蛋白质荧光峰Ex/Em=313/380 nm。FeCl3和CaO的加入一方面破坏了污泥颗粒的细胞结构,使EPS大量溶出,细胞结合水变成表面吸附水;另一方面Fe3+和CaO水解,中和污泥负电荷,通过压缩双电层作用破坏污泥胶体颗粒的稳定,去除表面吸附水,大幅提高了污泥的脱水性能,利于进一步板框压滤脱水。     

微生物絮凝剂改善城市污水厂浓缩污泥脱水性能的研究

采用酱油曲霉(Aspergillus sojae)产生的微生物絮凝剂(MBF)作为污泥絮凝脱水剂,对城市污水处理厂浓缩污泥进行调理,确定该絮凝剂对浓缩污泥脱水的处理工艺参数为：微生物絮凝液最佳投加体积为6%～8%（体积比）,发挥絮凝作用的最适污泥温度为28～32℃,最适pH为6～7。经微生物絮凝剂调理的污泥在3 000 r/min离心9 min,污泥脱水率高达82.7%,滤饼含水率降低至77.3%,污泥脱水后体积减至原来的1/5左右。     

城市污水处理厂的自动控制设计要点

通过一个城市污水处理厂自动控制系统的选取与设汁过程作为实例,说明了可编程逻辑控制器(PLC)自动控制方案是当今城市污水处理厂的最佳选择。论文对PLC自动控制方案的设计过程提出了详细的指导,将基于PLC的生产过程自动化与办公自动化进行了有机结合,为大型污水处理厂自动化控制设计提供了极重要的借鉴。     

人工湿地污水处理系统中的植物氮磷吸收富集能力研究

比较研究了人工湿地污水处理系统中7种植物对氮、磷的吸收能力.研究表明,所选7种湿地植物,稳定生长4个月后,平均总生物量在1 215～3 500 g/m2,植物氮、磷平均质量浓度分别为13.76～23.11、1.44～3.80 mg/g.香蒲具有最高氮积累量达48.18 g/m2,梭鱼草具有最高磷积累量为7.23 g/m2,姜草对氮、磷的积累量最低分别为21.40、1.68 g/m2.植物地上部氮、磷积累量与地下部的氮、磷积累量差异较大,除姜草外,植物地上部、地下部的氮、磷积累量比均大于3,黄花美人蕉地上部、地下部的氮、磷积累量比分别达11.75、12.10.通过植物收割去除氮、磷量约占湿地总去除量的2%～6%.