Ru-TiO_2光电极对亚甲基蓝的光电催化降解

采用阳极氧化法制备Ru-TiO2光电极,以该电极为工作电极,石墨作对电极,饱和甘汞电极为参比电极,对亚甲基蓝溶液的光电催化降解进行了研究。结果表明:煅烧温度600℃,掺杂1%Ru的Ru-TiO2光电极催化活性最好;以紫外灯(125 W)为光源,当外加偏压0.2 V,pH为5时,Ru-TiO2光电催化亚甲基蓝120 min可使其完全脱色;亚甲基蓝的光电催化降解遵从Langmuir-Hinshelwood动力学模型,测得其反应速率常数k=0.781 mmol/(L.min),吸附常数K=0.225 L/mmol。     

Ru-TiO2光电极对亚甲基蓝的光电催化降解

采用阳极氧化法制备Ru—TiO2光电极,以该电极为工作电极,石墨作对电极,饱和甘汞电极为参比电极,对亚甲基蓝溶液的光电催化降解进行了研究。结果表明：煅烧温度600oC,掺杂1％Ru的Ru-TiO2光电极催化活性最好;以紫外灯（125W）为光源,当外加偏压0．2V,pH为5时,Ru-TiO2光电催化亚甲基蓝120min可使其完全脱色;亚甲基蓝的光电催化降解遵从Langmuir—Hinshelwood动力学模型,测得其反应速率常数k：0．781mmol／（L·min）,吸附常数K=0．225L／mmol。     

LiFePO4非均相Fenton法处理亚甲基蓝染料的研究

采用水热法制备出LiFePO4催化剂,通过电子显微镜(SEM)、X射线衍射(XRD)和傅立叶红外光谱(FTIR)对其进行表征,并将其作为非均相Fenton催化剂处理亚甲基蓝(MB)染料溶液。实验结果表明,在催化剂用量为4 g/L,H2O2浓度为0.04 mol/L,pH值为3,温度为50℃,反应时间为60 min的条件下,浓度为500 mg/L的亚甲基蓝脱色率达99%。根据实验结果,讨论了LiFePO4作为非均相Fenton催化剂对亚甲基蓝的降解机理。     

铁碳微电解填料制备及其对亚甲基蓝的降解

针对传统铁碳微电解工艺中填料易板结的问题,在较低的烧结温度800 ℃条件下,将铁、活性炭、粘结剂和催化剂按一定配料比混合烧结4 h制备了一种铁碳微电解填料。将印染废水中的染料成分亚甲基蓝作为目标污染物,探究溶液pH、铁碳材料添加量和亚甲基蓝起始浓度等反应条件对亚甲基蓝降解效率的影响。在pH=3,铁碳投加量30 g·L-1,亚甲基蓝浓度10 mg·L-1的条件下,亚甲基蓝的去除率达到55%左右;相同条件下对于微电解填料的循环使用实验中亚甲基蓝的去除率能维持在50%以上,证明了该微电解填料具有连续运行的能力。另外,通过微电解与芬顿反应联用的初步实验发现联用效果对于亚甲基蓝的降解率能大幅度提升至90%以上,证明微电解与芬顿反应联用具有较大的应用潜力。     

LiFePO_4非均相Fenton法处理亚甲基蓝染料的研究

采用水热法制备出LiFePO4催化剂,通过电子显微镜（SEM）、X射线衍射（XRD）和傅立叶红外光谱（FTIR）对其进行表征,并将其作为非均相Fenton催化剂处理亚甲基蓝（MB）染料溶液。实验结果表明,在催化剂用量为4 g/L,H2O2浓度为0.04 mol/L,pH值为3,温度为50℃,反应时间为60 min的条件下,浓度为500 mg/L的亚甲基蓝脱色率达99%。根据实验结果,讨论了LiFePO4作为非均相Fenton催化剂对亚甲基蓝的降解机理。     

亚甲基蓝溶液的光催化脱色及降解

以高压汞灯为光源,在自ＴｉＯ２纳米粉末悬浮体系内,以在蓝溶液光催化降解脱色反应为模型,研究了其脱色降解动力学及其影响因素。研究表明,亚甲基蓝光催化反应动力学常数为４．５３μｍｏｌ／Ｌ．ｍｉｎ．吸附常数为３３．５５Ｌ／ｍｍｏｌ;随着ｐＨ值的上升以及Ｈ２Ｏ２的加入,其脱色降解速率加快。     

Feasibility study of photoelectrochemical degradation of methylene blue with three-dimensional electrode-photocatalytic reactor

The photoelectrochemical degradation of methylene blue in aqueous solution was investigated with three-dimensional electrode-photocatalytic reactor. It was found that the methylene blue could be degraded more efficiently by photoelectrochemical process than by photocatalytic oxidation or electrochemical oxidation alone. The decolorization efficiency and COD reduction were 95% and 87% for a photoelectrochemical process, respectively, while they were only 78% and 68% for a single electrochemical process and 89% and 71% for a single photochemical process. The TOC reduction of the former also reached as high as about 81% within a reaction time of 30.0 min. And these degradation reactions conformed to pseudo-first-order kinetics.     

光纤传导可见光降解亚甲基蓝

针对浓度大、色度高的印染废水难以处理的情况,选用加入光纤的光催化体系进行研究。采用溶胶凝胶法制备了Ag+/TiO2粉体光催化剂,用固体紫外可见光谱、X射线衍射对其进行表征。选用亚甲基蓝溶液作为目标降解物,评价了Ag+/TiO2在可见光下的光催化活性。分别考察了加入石英芯侧光光纤与塑料侧光光纤反应体系下,催化剂量、光纤数量、光照强度和pH值等因素对亚甲基蓝降解实验的影响。结果表明,选用20 mg/L的亚甲基蓝,采用催化剂量为11.67 g/L,500根侧光光纤,300 W的外部光源,pH值约为11时,光催化降解效果最佳,均能达到90%以上。     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

TiO2-rGO制备及其对亚甲基蓝溶液的降解

本实验用改进的Hummers法制备氧化石墨烯(GO),通过溶胶-凝胶法制备得到TiO2-石墨烯复合材料(TiO2-rGO),研究了不同制备条件对复合材料光催化性能的影响。采用X射线衍射(XRD),拉曼光谱(Raman),比表面积(BET),扫描电镜(SEM),透射电镜(TEM)、紫外-可见(UV-Vis)吸收光谱和荧光光谱(PL)等测试手段对复合材料进行表征。结果表明,TiO2-rGO复合材料中的TiO2为锐钛相,且能均匀附着在石墨烯片层上,呈现层状堆积结构;与纯TiO2相比,复合材料具有较大的比表面积和更高的可见光响应。研究了该复合催化剂在紫外光下对亚甲基蓝以降解效果。当焙烧温度为450℃、TiO2/GO质量比为125:1时,制备得到的TiO2-rGO具有最优的光催化效果。     

基于过碳酸钠的类Fenton体系对亚甲基蓝的降解动力学

采用改良低温结晶法制备过碳酸钠(sodium percarbonate,SPC),对其进行XRD表征,并用以作为氧化剂构建类Fenton体系(SPC/Fe2+)降解亚甲基蓝(MB),对其降解的影响因素及反应动力学进行了研究。结果表明,在该体系中,当溶液初始pH分别为2~10时,亚甲基蓝的去除率在1 min时均可达到97%以上,说明该体系可高效去除水体中的亚甲基蓝,反应速率快,且过碳酸钠的使用可以拓宽Fenton反应的pH范围。该反应的最佳工艺条件为0.75 g·L-1硫酸亚铁,300 mg·L-1过碳酸钠,亚甲基蓝去除率在反应10 min后可达99.0%。亚甲基蓝在该体系中的降解遵循二级反应动力学方程,反应速率常数分别为64.50×10-3 L·(mol·s)-1,快于Fenton体系的17.83×10-3 L·(mol·s)-1。该体系反应活化能为16.6 kJ·mol-1,远小于Fenton体系(46.234 kJ·mol-1),说明以过碳酸钠为氧化剂更有利于非均相类Fenton反应的发生。     

Visible light-driven photocatalytic degradation of methylene blue dye over bismuth-doped cerium oxide mesoporous nanoparticles

Environmental Science and Pollution Research - A series of Bi3+-doped ceria nanoparticles (0 to 20 wt% of Bi3+) were synthesized by sol-gel assisted hydrothermal method at a lower temperature of...     

Physical properties of PVDF-GO/black-TiO2 nanofibers and its photocatalytic degradation of methylene blue and malachite green dyes

Environmental Science and Pollution Research - Black TiO2 and graphene oxide (GO) have attracted intensive attention as an effective catalyst on visible light driven for photodegrading of dyes. In...     

Gadolinium nanoparticle-decorated multiwalled carbon nanotube/titania nanocomposites for degradation of methylene blue in water under simulated solar light

Gadolinium oxide nanoparticles of diameters <5 nm were uniformly decorated on the surfaces of multiwalled carbon nanotubes which were subsequently used as templates to fabricate gadolinium oxide nanoparticle-decorated multiwalled carbon nanotube/titania nanocomposites. The prepared nanocomposites were evaluated for the photocatalytic degradation of methylene blue under simulated solar light irradiation. Higher photocatalytic activity was observed for the gadolinium oxide-decorated multiwalled carbon nanotube-based nanocomposites compared to the neat multiwalled carbon nanotube/titania nanocomposite and commercial titania. This improvement in photocatalytic activity was ascribed to the gadolinium oxide nanoparticles supported at the interface of the carbon nanotubes and titania resulting in efficient electron transfer between the two components of the composite. Total organic carbon (TOC) analysis revealed a higher degree of complete mineralisation of methylene blue (80.0 % TOC removal) which minimise the possible formation of toxic by-products. The photocatalyst could be re-used for five times, reaching a maximum degradation efficiency of 85.9 % after the five cycles. The proposed photocatalytic degradation mechanism is outlined herein.     

Direct degradation of methylene blue by unactivated peroxymonosulfate: reaction parameters,kinetics, and mechanism

Environmental Science and Pollution Research - Advanced oxidation processes (AOPs) are efficient methods for water purification. However, there are few studies on using peroxymonosulfate (PMS) to...     

Adsorption and photocatalytic properties of porphyrin loaded MIL-101 (Cr) in methylene blue degradation

Environmental Science and Pollution Research - In this study for the very first time, zinc tetraphenylporphyrin (ZnTPP) was loaded into MIL-101 (Zn[TPP]@MIL-101) to perform an adsorptive and...     

Heterogeneous irradiation system: enhanced degradation of methylene blue by electron beam irradiation combined with graphite carbon nitride/carbon nanodots

Environmental Science and Pollution Research - In the present work, the degradation of methylene blue (MB) was investigated by electron beam irradiation combined with graphite carbon nitride/carbon...     

复合型CoO/TiO2光催化剂降解亚甲基蓝动力学研究

以钛酸四丁酯为前驱体,采用溶胶凝胶法,制备了CoO掺杂的TiO2光催化剂。利用X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）、紫外可见漫反射（UV-vis DRS）对催化剂进行了分析、表征。以中压汞灯为光源,研究了亚甲基蓝（MB）在CoO/TiO₂微粒水悬浮液中的降解动力学。结果表明：所制备的催化剂活性组分主要是锐钛矿型的二氧化钛和CoO固溶体,粒径为25～30 nm,分布均匀。亚甲基蓝的光催化降解动力学满足一级动力学,在一定的浓度范围内,反应速率常数随初始浓度增大而减少,适当的掺钴量可以有效地提高TiO₂光催化活性,其最佳掺杂量重量百分比为0.25%。     

Ni/Fe双金属降解四氯化碳和四氯乙烯的对比试验

以四氯化碳(CT)和四氯乙烯(PCE)为目标污染物,以批试验方法研究Ni/Fe双金属对CT和PCE的还原性脱氯.结果表明:Ni/Fe双金属可有效去除水中的CT和PCE;Ni/Fe双金属对CT和PCE的降解反应均符合准一级反应动力学方程;在相似的反应条件下,Ni/Fe双金属对CT和PCE脱氯的反应速率常数(kobs)之比为1.48和1.67,说明Ni/Fe双金属对CT的脱氯速率要快于对PCE的脱氯速率;Ni/Fe双金属可对PCE完全脱氯,但对CT脱氯过程中产生少量三氯甲烷(TCM).     

Fabrication of visible light active Mn-doped Bi2WO6-GO/MoS2 heterostructure for enhanced photocatalytic degradation of methylene blue

Environmental Science and Pollution Research - The increase in environmental pollution has led to an increased investigation in the development of novel ternary photocatalytic systems for...