Removal of DEHP in composting and aeration of sewage sludge

The potential of composting and aeration to remove bis(2-ethylhexyl) phthalate (DEHP) from municipal sewage sludge was studied with two dewatered sludges: raw sludge and anaerobically digested sludge. Composting removed 58% of the DEHP content of the raw sludge and 34% of that of the anaerobically digested sludge during 85 days stabilisation in compost bins. A similar removal for the anaerobically digested sludge was achieved in a rotary drum in 28 days. Less than 1% of DEHP was removed with the compost leachate. Although DEHP removal was greater from raw sludge compost than anaerobically digested sludge compost, the total and volatile solids removals were on the same level in the two composts. In the aeration of raw sludge at 20 degrees C the DEHP removals were 33-41% and 50-62% in 7 and 28 days, respectively. Both composting and aeration are concluded to have the potential to reduce the DEHP contents typically found in sewage sludges to levels acceptable for agricultural use.     

投加方式和通风速率对脱水污泥堆肥效果的影响

为了在降低能耗的前提下获得更高的污泥堆肥效率和提高堆肥产品质量,利用梨形筒式好氧堆肥反应器,设置2种物料投加方式和3种通风速率,研究堆肥过程中温度、含水率、总氮以及发芽指数（GI）的变化特性。结果表明,与间歇式堆肥相比,连续式堆肥可以显著提高堆体温度和堆体腐熟度,降低堆体含水率及缩短腐熟期,但氮素损失也显著增大（P-1的连续式堆肥,堆体维持高温时间最长,且最终温度稳定在较高温度47～48 ℃,堆末含水率最低,氮素损失处于三者的中间水平,腐熟期最短。综合分析,在通风速率为1.95 L·min-1的连续运行方式下,梨形筒式反应器用于污泥稳定高效堆肥是可行的。     

通风速率对烟草废料堆肥腐熟及元素变化影响

以烟草废料为原料堆肥,设置不同的通风速率,通过对堆肥中温度、营养元素和腐殖质等指标变化的研究,揭示了通风速率对堆肥腐熟和主要元素变化的影响。结果表明,通风速率为0.1和0.2 m3/(h·m3)的处理的高温期持续时间在5 d以上,满足堆肥无害化卫生标准要求,堆肥积温以0.2 m3/(h·m3)的处理最高;堆肥结束时,通风速率为0.2和0.3 m3/(h·m3)处理的总碳含量降低率、总氮含量增加率及NO3--N含量增幅均强于0.1 和0.4 m3/(h·m3)的通风处理,且两处理的NH4+-N含量至堆肥结束时降至400 mg/kg阈值以下;通风速率为0.2 m3/(h·m3)的处理的终产品的腐殖化质数为1.91,达到腐熟阈值1.90。综合以上结果表明,0.2 m3/(h·m3)的通风速率较适于烟草废料堆肥腐熟和营养转化。     

Influence of aeration rate and reactor shape on the composting of poultry manure and sawdust

To achieve successful composting, all the biological, chemical, and physical characteristics need to be considered. The investigation of our study was based on various physicochemical properties, i.e., temperature, ammonia concentration, carbon dioxide concentration, pH, electrical conductivity (EC), carbon/nitrogen (C/N) ratio, organic matter (OM) content, moisture content, bacterial population, and seed germination index (GI), during the composting of poultry manure and sawdust for different aeration rates and reactor shapes. Three cylindrical-shaped and three rectangular-shaped pilot-scale 60-L composting reactors were used in this study, with aeration rates of 0.3 (low), 0.6 (medium), and 0.9 (high) L min^?1 kg^?1 DM (dry matter). All parameters were monitored over 21 days of composting. Results showed that the low aeration rate (0.3 L min^?1 kg^?1 DM) corresponded to a higher and longer thermophilic phase than did the high aeration rate (0.9 L min^?1 kg^?1 DM). Ammonia and carbon dioxide volatilization were directly related to the temperature profile of the substrate, with significant differences between the low and high aeration rates during weeks 2 and 3 of composting but no significant difference observed during week 1. At the end of our study, the final values of pH, EC, moisture content, C/N ratio, and organic matter in all compost reactors were lower than those at the start. The growth rates of mesophilic and thermophilic bacteria were directly correlated with mesophilic and thermophilic conditions of the compost. The final GI of the cylindrical reactor with an airflow rate of 0.3 L min^?1 kg^?1 DM was 82.3%, whereas the GIs of the other compost reactors were below 80%. In this study, compost of a cylindrical reactor with a low aeration rate (0.3 L min^?1 kg^?1 DM) was more stable and mature than the other reactors.

Implications: The poultry industry is growing in South Korea, but there are problems associated with the management of poultry manure, and composting is one solution that could be valuable for crops and forage if managed properly. For high-quality composting, the aeration rate in different reactor shapes must be considered. The objective of this study was to investigate various physicochemical properties with different aeration rates and rector shapes. Results showed that aeration rate of 0.3 L min^?1 kg^?1 DM in a cylindrical reactor provides better condition for maturation of compost.     

Effects of multiple antibiotics on greenhouse gas and ammonia emissions during swine manure composting

Environmental Science and Pollution Research - Antibiotics are commonly used in intensive farming, leading to multiple antibiotic residue in livestock waste. However, the effects of multiple...     

高效堆肥菌种的筛选及在城市污泥堆肥上的应用

分离筛选出了4株猪粪堆肥菌种,初步的分类鉴定表明它们均属于芽孢杆菌属.利用这些菌种制成混合菌剂,并进行城市污泥堆肥对比试验,结果显示,接菌处理在各项堆肥指标上明显优于未接菌的空白处理,自制菌与酵素菌在堆肥过程中具有非常相似的发酵能力,均能加快堆肥的升温速度,提高堆肥的最高温度,加快物料含水率的下降.说明自制菌不但可以应用于猪粪的堆肥发酵,在城市污泥高温堆肥方面也有很好的应用潜力.     

新型堆肥生物反应器人粪便堆肥功效的评价

利用以锯末为载体的Bio-Lux S15型生态卫生设备,对人粪便进行了连续性堆肥实验,考察了BOD₅、粪大肠菌和蛔虫卵的灭活以及最终产品N、P和K等肥料成分的含量。实验结果表明,最初30 d,BOD₅的累积去除率由27％快速增加到50％,之后的30 d维持在50％左右,随后下降至40％左右。生态卫生设备中维持50～60℃的温度是杀灭粪便病原微生物的适宜条件,可保证粪便投入后在24 h内,粪大肠菌的灭活率达到99.99％,蛔虫卵的灭活率在2 h内达100%。对反应周期内载体的N、P和K等肥料成分的分析结果表明,反应过程中3种肥分都持续积累,在反应末期,按TN、P₂O₅和K₂O计算的3种肥分最终分别达到25.1、123.4和2.0 g/kg,基本上达到了农用肥料的国家标准,表明以锯末为载体的反应器具有良好的堆肥效果。     

城市生活垃圾堆肥试验装置的设计

堆肥装置是研究堆肥过程中各种参数变化和获取优化参数的必不可少的工具。本文从堆肥维持其温度的先决条件出发，并在大量调研的基础上确定了实验室好氧发酵装置的合理尺寸、渗沥水收集和回喷系统、布气系统等。该装置的尺寸为长1m，宽0．5m，高0．6m，堆料的高度为0．48m；根据垃圾样品的理化性质，确定了渗滤液回喷的时间为116S、鼓风机的风量为0．055m^3／min，风压为300Pa，并且对其引入自动控制设备，使通风工作5min、休息35min。最后利用生活垃圾堆肥试验验证该装置满足堆肥的一次发酵要求。该装置采用自动控制系统，布水、布气均匀，保温效果好，发酵过程温度测定方便快捷，而且还有功率消耗小、臭气集中易于处理的优点。     

曝气量和曝气时长对好氧颗粒污泥活性恢复的影响

采用啤酒废水,在SBR中对在4℃的冰箱中储存8周的好氧颗粒污泥进行活性恢复。设置曝气时长分别为150 min和270 min,曝气量分别为0.1 m3/h和0.2 m3/h,考察了曝气时长和曝气量对好氧颗粒污泥活性恢复的影响。实验结果表明,好氧颗粒污泥在4℃冰箱中储存8周后,其颜色、粒径无明显变化;设置较长曝气时间(270 min)、较大曝气量(0.2 m3/h)时,颗粒污泥平均沉降速率、MLSS和SVI恢复最快,且对COD处理效果也恢复较快。而短曝气时间(150 min)、小曝气量(0.1 m3/h)有利于好氧颗粒污泥对氨氮去除效果的恢复。     

Changes in lipids and sterols during composting

Pyrolysis-gas (Py-GC) chromatography was used to characterize organic [(diethyl ether (DEE) and chloroform (CHCl3)] extracts of raw and composted duck excreta enriched wood shavings from two finishing cycles (C1 and C2). Materials were collected on days 0, 8 and 23. C1 contained 1.7 % total N while C2 contained 0.9 % total N. Py-GC-MS (mass spectrometry) showed that the extracts contained n-alkanes (C12 to C32), alkenes (C12:1 to C33:1), n-fatty acids (C12 to C28), unsaturated fatty acids (C18:1 and C18:2), and sterols (cholestene, cholestadiene, stigmastene, stigmastadiene, stigmastatriene, cholesterol, stigmastanol, stigmastanone, stigmastadienone, 17-methyl dialkylsulfanyl decahydro-1H-cyclopenta [a] phenanthrene, 17-methyl dialkylsulfanyl dodecahydro-1H-cyclopenta [a] phenanthrene, and 17-methyl-17-dialkylsulfanyl decahydro-1H-cyclopenta [a] phenanthrene). Other components identified were prystene, squalene (precursor of cholesterol), phthalic acid, diphenylpropane, diphenylbut-2-ene and 1,3,6 triphenyl hex-4-ene. Our data showed significant changes in the lipid composition of duck excreta enriched wood shavings during composting, which appeared to be related to the total N content of the system.     

城市生活垃圾堆肥试验装置的设计

堆肥装置是研究堆肥过程中各种参数变化和获取优化参数的必不可少的工具.本文从堆肥维持其温度的先决条件出发,并在大量调研的基础上确定了实验室好氧发酵装置的合理尺寸、渗沥水收集和回喷系统、布气系统等.该装置的尺寸为长1 m,宽0.5 m,高0.6 m,堆料的高度为0.48 m;根据垃圾样品的理化性质,确定了渗滤液回喷的时间为116 s、鼓风机的风量为0.055 m3/min,风压为300 Pa,并且对其引入自动控制设备,使通风工作5 min、休息35 min.最后利用生活垃圾堆肥试验验证该装置满足堆肥的一次发酵要求.该装置采用自动控制系统,布水、布气均匀,保温效果好,发酵过程温度测定方便快捷,而且还有功率消耗小、臭气集中易于处理的优点.     

曝气时长对中试曝气塘-浮萍塘联合系统中污染物去除的影响

浮萍塘污水处理技术具有管理简便、运行成本低、可资源化回收氮磷污染物等优势。然而,因水体溶解氧(DO)不足造成的污染物去除率低的问题限制了该技术的推广应用。为此,本研究在浮萍塘前端引入曝气塘,构建中试曝气塘-浮萍塘联合系统,借此增加浮萍塘DO含量,并进一步考察了曝气时长(0、0.5、1、2和4 h)对污染物去除效果及浮萍生长的影响,以此探寻低耗高效的最佳曝气时长。结果表明,曝气塘可有效降低水体的浊度,但对氮磷去除的贡献较小,氮磷的去除以浮萍塘为主。曝气处理可显著提高曝气塘及浮萍塘水体DO含量和氧化还原电位(Eh),且DO和Eh随曝气时长的增加而上升。此外,曝气处理还能显著促进浮萍生长及其污染物的去除,但促进效果并未简单地随曝气时长的增加而提高。其中,TN、氨氮和浊度的去除率在曝气时长1 h时已基本达到峰值(去除率分别为58.42%、61.89%和89.90%),TP去除率虽在曝气时长4 h时最大(81.44%),但与曝气时长0.5 h(73.05%)相比并无显著差异;浮萍虽在曝气时长2 h时干基生长速率最高(8.00 g·(m²·d)⁻¹),但与曝气时长0.5 h和1 h(7.35 g·(m²·d)⁻¹左右)相比也无显著差异,而曝气成本却成倍增加。因此,综合考虑污染物去除、浮萍生长及曝气成本,建议曝气时长不宜高于1 h,推荐0.5~1 h为佳。以上结果可为曝气塘-浮萍塘联合系统的应用及曝气时长的选择提供参考。     

微气泡曝气中氧传质特性研究

气泡曝气过程中氧传质对于好氧生物处理过程具有重要意义。采用水力旋转剪切微气泡发生装置,考察了运行条件和水质特性对微气泡曝气中氧传质特性的影响。结果表明,微气泡曝气可获得较高的气含率和气泡停留时间;表面活性剂十二烷基磺酸钠(SDS)可以提高微气泡曝气的气含率和气泡停留时间。微气泡曝气中氧的总体积传质系数明显高于传统气泡曝气。总体积传质系数随着空气流量的增加而增加;氧传质效率随着空气流量的增加而减小,且对空气流量的变化更为敏感。在温度15~35℃范围内,微气泡曝气中氧的总体积传质系数随着温度的增加而增加,变化关系与传统气泡曝气基本相同,但对温度的变化更为敏感。微气泡曝气中,表面活性剂SDS会使氧的总体积传质系数略有降低,其不利影响明显小于传统气泡曝气;氧的总体积传质系数随盐度(NaC l浓度)增加而逐渐增加,并在NaC l浓度5 000 mg/L后趋于稳定。     

好氧堆肥反应器对人粪便堆肥中温降解的中试研究

控制温度为（35±2）℃,以新鲜锯末为空白载体,在控制含水率为55%~60%和强制通风的好氧条件下,进行为期15 d的实验,进行了人粪便好氧堆肥的中试研究,重点分析了在堆肥过程中有机物的降解、氮素的迁移转化规律及生物量的变化。结果表明,粪便中有机物含量在前2天稍微上升,然后迅速下降,最终去除率为71.82%;随着NH₃-N释放量的增加,堆料中N_tot含量从第4天开始减少,最终损失 22.61%,其中N_org损失占74.35%,NH₃-N占23.52%;所损失的氮素有91.66%以氨氮的形式释放。粪便中的有机物和氮的含量能在8~10 d后达到稳定,且堆体无臭味;粪便中溶解性有机物为微生物的生长提供营养物质,因此生物量变化的过程与有机物降解的有着紧密的联系;病原菌在堆肥过程中得到有效去除,表明该反应器堆肥的无害化。     

一种新型可控堆肥反应器系统的快速好氧堆肥实验

研究自制可控堆肥反应器对城市污泥进行快速好氧堆肥的工艺效能。实验结果表明:新型堆肥反应器的可控性强。当初始入料堆体温度控制在40℃左右,含水率控制在50%左右时,堆体温度能在第3天就升至55℃以上,并维持5 d以上。含水率、pH、电导率、种子发芽指数(G I)和可挥发性固体(VS)等指标均具有良好的变化规律,均可作为堆肥腐熟度的表征和评价参数。反应器13 d即可完成一个堆肥周期,且堆肥产品的腐熟程度极高。     

翻转式堆肥反应装置设计研究

以复合微生物菌剂降解垃圾的适宜条件为出发点 ,根据堆肥小试实验结果 ,确定进料垃圾特性、合理的工艺参数及一次发酵完成时间 ,结合制备装置材料的保温性、堆肥物料平衡、热量平衡 ,合理确定反应装置容积、供气方式、操作运行条件 ,开发了翻转式堆肥反应装置。该装置具有堆料搅拌均匀、进出料简单、供气均衡等特点     

不同曝气参数下间歇增氧垂直流人工湿地脱氮的分层效应

以新型间歇增氧垂直流人工湿地(IA-VFCW)为研究对象,揭示了不同工况对人工湿地污染物去除的分层效应及去除效果的影响。结果表明∶不同曝气参数对细砾石层、煤渣层污染物去除的影响较小;对曝气区、湿地植物区污染物去除的影响较大。当进水${\rm{NH}}_4^ + $-N质量浓度为25 mg·L−1、COD为200 mg·L−1时,细砾石层、煤渣层对${\rm{NH}}_4^ + $-N和TN平均去除率分别为10.8%、9.3%和13.3%、11.6%,两区域中均无${\rm{NO}}_2^ - $-N、${\rm{NO}}_3^ -$-N的积累;细砾石层对COD去除的贡献较大,COD平均去除率为67.2%。曝气区对${\rm{NH}}_4^ + $-N、TN去除贡献较大,${\rm{NH}}_4^ + $-N、TN的最大去除率分别达到69.3%、40.9%,COD平均去除率为25.4%。在低曝停比下,曝气量的增加将提高IA-VFCW对TN的去除性能;在高曝停比下,曝气量的增加会降低IA-VFCW对TN的去除效果,且会造成${\rm{NO}}_３^ - $-N积累。在曝气量2 m3·h−1、曝停比1/3、曝停周期6 h工况下IA-VFCW具有较好的污染物去除效果,${\rm{NH}}_4^ + $-N去除率为94.9%、TN去除率为77.0%、COD去除率为90.0%。IA-VFCW脱氮性能明显优于传统垂直流人工湿地。     

曝气生物滤池中碳和氮代谢特性

用充填陶瓷滤料的曝气生物滤池研究碳和氮代谢特性.曝气生物滤池进水氨氮为52 mg/L左右、COD为100 mg/L左右和回流比为200%时,经过20多d的运行,出水氨氮小于0.05 mg/L、COD小于25 mg/L、亚硝态氮为4.7 mg/L和硝态氮为7.1 mg/L,COD去除率达75%,氨氮去除率达99.9%,总氮去除率达78%;过大和过小的回流比对曝气生物滤池的运行性能都是不利的.研究成果可以应用于一般城市污水以及含低COD、高氨氮工业废水的处理.