首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
磁处理水对蚕豆根尖细胞的遗传学效应   总被引:1,自引:0,他引:1       下载免费PDF全文
利用蚕豆根尖细胞微核测试技术研究了磁化水(4200GS)对蚕豆根尖细胞的微核率、有丝分裂指数、染色体桥率、不正常细胞率等遗传学指标的影响,目的是探讨磁处理水对生物体的遗传学效应,结果发现上述指标均有所上升,其中微核率和不正常细胞率上升显著,并且其大小与水在磁场中处理的时间长短有关,提示磁处理水(4200GS)有一定的遗传学毒性  相似文献   

2.
The treatment of microglial BV-2 cells with sodium arsenate(As(V):0.1-400 μmol/L — 48 hr)induces a dose-dependent response.The neurotoxic effects of high concentrations of As(V)(100,200 and 400 μmol/L) are characterized by increased levels of mitochondrial complexesⅠ,Ⅱ,and Ⅳ followed by increased superoxide anion generation.Moreover,As(V) triggers an apoptotic mode of cell death,demonstrated by an apoptotic SubG1 peak,associated with an alteration of plasma membrane integrity.There is also a decrease in transmembrane mitochondrial potential and mitochondrial adenosine triphosphate ATP.It is therefore tempting to speculate that As(V) triggers mitochondrial dysfunction,which may lead to defective oxidative phosphorylation subsequently causing mitochondrial oxidative damage,which in turn induces an apoptotic mode of cell death.  相似文献   

3.
In tube hydroforming, the process chain can be very long as it may involve several pre-forming operations (e.g. bending, crushing, end forming, etc.) which are usually followed by an intermediate annealing stage. Conventional annealing is performed in batches and it is often perceived as a long, relatively expensive and non-environmentally friendly operation. For this reason, in this paper local intermediate heat treatment is proposed as a promising alternative solution, in order to reduce the throughput process time. The study has been carried out on a real tubular motorcycle part, by performing both experiments and numerical simulations, in order to verify whether local annealing can be an effective substitute of conventional global annealing. Several alternative ways of locally heat treating an Al6060 tube right before hydroforming have been investigated. The results demonstrate that a feasible solution can be found, with local heat treatment of relatively small portions of the tube.  相似文献   

4.
污水处理后的应用研究   总被引:1,自引:0,他引:1  
理化分析表明 ,溶剂生产后排放的污水 ,经厌氧—好氧二级生化处理具有一定的肥效 ,经进一步改良 ,可用作灌溉用水和无土栽培的营养液  相似文献   

5.
6.
A water quality model for water reuse was made by mathematics induction. The relationship among the reuse rate of treated wastewater(R), pollutant concentration of reused water( Cs ), pollutant concentration of influent( C0), removal efficiency of pollutant in wastewater( E), and the standard of reuse water were discussed in this study. According to the experiment result of a toilet wastewater treatment and reuse with membrane bioreactors, R would be set at less than 40%, on which all the concerned parameters could meet with the reuse water standards. To raise R of reuse water in the toilet, an important way was to improve color removal of the wastewater.  相似文献   

7.
This work was carried out under the Visiting Researcher's Programme of the Research Reactor Institute, Kyoto University.  相似文献   

8.
The mechanochemical treatment of fly ash generated from a medical waste incinerator was subjected to grinding for 2 hr at 400 r/min in a planetary ball mill. The treated fly ash was characterized by a suite of analytical methods including High Resolution Gas Chromatograph/High Resolution Mass Spectrometer, Mastersizer 2000 Particle Size Analyzer, QUADRASORBTM SI Surface Area Analyzer, Scanning Electron Microscopy and X-ray di raction. Results showed that abatement e ciency of polychlorinated dibenzop- dioxins and polychlorinated dibenzofurans (PCDDs/Fs) in terms of total concentration averagely amount to 76% which was relatively higher than that of I-TEQ concentration averagely amount to 56%; the most concentration of toxic congeners as well as isomers of PCDDs/Fs decreased after mechanochemical treatment. The treated fly ash was characterized by a more homogeneous distribution of concaves as well as the significant decreasing in overall particle size and great enlargement in surface area. The major crystallization phases or intensities were considerably changed by mechanochemical treatment, of which a new phase containing chlorine formed may be a possible factor suggesting chlorination reaction occurring on the crystalline surface.  相似文献   

9.
Microbial degradation of carbofuran was rapid in acid mineral soil collected from fields in Prince Edward island, Nova Scotia, New Brunswick and Ontario with a history of use of this insecticide and with pH ranging from 6.1 to 6.6. Concentrations of carbofuran ranging from 10 to 5000 ppm (μg active ingredient per g of over-dry-soil) degraded to levels not detectable by bioassay (< 0.2 ppm) in less than 1 day at 10 ppm, to in about 90 days at 5000 ppm. Concentrations of 200, 300 and 500 ppm of 10% carbofuran granules degraded almost as quickly as a 100-ppm application, but 1000, 2000 and 5000 ppm degraded more slowly. Soil from fields with a natural pH lower than 5.8 have not shown any evidence of rapid microbial breakdown of carbofuran.  相似文献   

10.
11.
疏水性分子筛对焦化废水生物处理尾水的吸附过程解析   总被引:1,自引:1,他引:1  
采用表面活性剂为模板剂常温一步合成疏水性介孔分子筛(MCM-41-dry)和通过煅烧去除模板剂得到亲水性介孔材料(MCM-41-cal).分别以制备的两种分子筛作为吸附剂吸附焦化废水生物出水中COD和TOC组分,考察吸附剂浓度、pH值等对吸附过程的影响,并对吸附过程进行动力学拟合.结果表明,MCM-41-dry的吸附效果远远强于MCM-41-cal,归因于含有模板剂的材料表面具有较强的疏水性及含有高吸附容量的季铵基团.在25℃、吸附剂浓度为2g·L-1时,MCM-41-dry对焦化废水中COD和TOC的去除率分别达53%和66%,吸附量分别为64mg·g-1和17mg·g-1.拟二级动力学模型能够真实反映整个吸附过程.水样吸附前后的GC/MS数据表明,焦化废水生物出水中残留了长链烷烃、卤代物、多环芳烃等难降解有机物,经MCM-41-dry吸附后,各种物质浓度均得到降低,MCM-41-dry尤其对疏水性烷烃类有较好的吸附效果,表明该吸附剂能够优先吸附疏水性物质.此外,吸附剂对水具有一定的润湿性能,能与废水充分接触,从而利于其吸附水中的污染物,这使其用于实际废水的处理成为可能.  相似文献   

12.
The environmental and social impact derived from treated wastewater reuse is an intrinsically complex multidimensional process, which involves multiple criteria and multiple stakeholders. This paper presents the use of multicriteria decision through the TOPSIS method, applied to six different methodologies concerning the disinfection of treated wastewater before reusing. Results have shown that the best disinfection technique for treated wastewater has been chlorination with 4 ppm, if this water is to be destined to an urban, agricultural or industrial use, due to a large weight given to cost and environmental criteria. Conversely, in recreational and environmental uses, the alternative of ultraviolet light disinfection was the chosen alternative. Economic criteria showed priority in the most entrepreneurial uses of the water, although social and political cost had a greater weight in the case of environmental or recreational uses. The inclusion of environmental and social assessment in the disinfection technique decision support clearly provides a cleaner and more sustainable production.  相似文献   

13.
通过建立香根草人工湿地系统,研究该系统对生活污水的COD、TP、TN的处理效果以及系统的耐污性。在水力停留时间(HRT)为6h的条件下,COD、TP、TN的去除率分别为63.5%、88.3%、72.4%。研究表明,香根草人工湿地系统对城镇生活污水具有较好的净化效果,且系统在该试验条件下耐污性良好。  相似文献   

14.
在水泥固化时将生活垃圾焚烧飞灰(简称飞灰)以不同的比例代替复合硅酸盐水泥并且用垃圾渗滤液浓缩液代替水进行固化实验,研究了飞灰掺量(40%、50%、60%)、浓缩液替代水对水泥固化法固化效果及重金属(Zn、Pb、Cd、Cr、As、Ba)浸出的影响.结果表明:飞灰掺入量的增加会降低固化体的抗压强度,但浓缩液替代水对固化体的抗压强度没有显著影响.不同重金属的浸出行为受掺灰率的影响不同,掺灰率的增加会减少固化体中Zn的浸出,增加Pb和Cd的浸出,Zn、Pb、Cr、As在第36d可达到稳定浸出量不再增加,Ba的累积浸出量持续增加,加入浓缩液后固化体中Pb、Zn、Cd、Cr、As等重金属的浸出量未超过标准限值,可以满足固化处理对浸出毒性的要求.  相似文献   

15.
针对上海地区大型公共建筑中水回用问题,采用蒙特卡罗模拟技术,对其全生命周期成本效益进行了分析,并讨论了水价对中水工程成本效益的影响.成本计算结果表明生物接触氧化工艺在全生命周期内总成本集中在240.27~276.00万元之间.不同水价方案计算结果表明,在上海现行水价的条件下,生物接触氧化工艺全生命周期效益主要集中在-53.98~-37.54万元之间,50年内不存在投资回收期;当水价为3.8元/t时,生物接触氧化工艺的全生命周期效益主要集中在23.03~51.94万元之间,投资回收期为18~19a;当水价为6.10元/t时,工程效益主要集中在192.47~263.36万元之间,投资回收期为4~5a.因此单从中水工程的成本效益角度来看,上海现行水价偏低,中水回用工程缺乏推广优势,建议适当提高水价或对中水回用工程进行补贴.  相似文献   

16.
以我国本土野生植物苘麻为研究对象,通过盆栽和萌发实验,研究了苯磺隆和莠去津2种除草剂施用于苘麻花期对收获种子的萌发和幼苗生长的影响.结果表明,苯磺隆和莠去津均对苘麻繁殖具有延续影响.苯磺隆对苘麻的种子萌发百分率和平均发芽时间影响不显著,而使种子萌发初始时间提前或推迟,随着浓度增加变化无规律性.大田推荐剂量浓度的苯磺隆(22.5g ai/hm2)抑制第7天幼苗生长特别是子叶下胚轴生长,而低于大田推荐剂量的6个浓度均促进第7d幼苗生长.大田推荐剂量浓度1/16的莠去津(75g ai/hm2)处理后所获得种子萌发百分率显著高于空白对照和其它处理获得的种子萌发百分率,施用大田推荐剂量(1200g ai/hm2)和大田推荐剂量浓度1/4的莠去津(300g ai/hm2)使种子初始萌发时间显著推迟.莠去津使种子平均发芽时间显著增加,大田推荐剂量浓度1/64(0.35g ai/hm2)和1/4的莠去津抑制第7天幼苗生长.  相似文献   

17.
18.
19.
采用单室无膜悬浮阴极微生物燃料电池(MFC),对比分析了不同处理方式的污泥(直接污泥、微波预处理污泥和酶强化水解污泥)为燃料时MFC产电特性、污泥减量化效果和能源效率.研究表明,酶强化污泥为燃料的MFC(ESMFC)产电周期最长(41d),功率密度最大(775.21mW/m2),但库仑效率(CE)仅10.58%.采用微波污泥为燃料的MFC(MSMFC)CE最高(84.6%),而产电周期(30d)和功率密度(343.41mW/m2)居中.采用直接污泥为燃料的MFC(SMFC)产电周期(15d)、功率密度(294.53mW/m2)和CE(5.8%)均最小.采用直接污泥为燃料的MFC中TCOD去除率为26.2%,VSS去除率为32.5%.采用污泥预处理手段有利于促进污泥减量化,MSMFC和ESMFC中TCOD去除率分别增加到58.5%和63.2%,VSS去除率分别增加到73.9%和77.1%.  相似文献   

20.
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号