Biodegradable municipal solid waste: characterization and potential use as animal feedstuffs

Five different fractions of the biodegradable municipal solid waste (BMSW) were evaluated as potential animal feedstuffs. For each source of waste (meat waste (MW), fish waste (FW), fruit and vegetables waste (FVW), restaurant waste (RW), household waste (HW)), samples were obtained from small shops (butchers, fishmongers, fruit and vegetable shops), restaurants and a MSW treatment plant (household waste). The chemical composition, microbiological characterization, dioxins, furans, PCB's and mineral content were determined for every type of waste fraction. The analysed biodegradable waste presented high moisture content (from 60% to 90%). Some fractions were dense in one nutrient: meat waste in ether extract, fish waste in crude protein, fruit and vegetable waste in nitrogen free extract. The other studied fractions (restaurant fraction and household fraction) presented a more balanced composition, but the presence of toxic concentrations of contaminants such as metals was higher than European legislation permitted values in animal feeding. From a microbiological standpoint, a heat treatment at 65 degrees C for 20 min was sufficient to ensure microbiological quality of the samples. This treatment was also advisable to reduce the moisture content: a lower moisture content facilitates the waste handling and processing and, therefore, the inclusion of these waste fractions in commercial animal diets. This paper presents a potential alternative for the recovery of organic matter content in municipal solid waste. The results obtained in this research and the feedstuffs legislation in force related to animal feed, indicated that some of the studied biodegradable waste fractions (meat waste, fruit and vegetable waste and fish waste) could be considered as alternatives to typical raw materials used in animal feeds.     

Tropical agricultural residues and their potential uses in fish feeds: the Costa Rican situation

In Costa Rica as many other tropical countries, the disposal problem of agricultural wastes is widely recognized but efforts to find solutions are not equal for different sectors. This study describes the situation of major agricultural residues in Costa Rica, identifying the activities with higher amounts produced and, the potential use of these residues in fish feeds. In Costa Rica, during the 1993-1994 production season, major agricultural sectors (crop and livestock) generated a total amount of 3.15-3.25 million MT of residues (classified in by-products: used residues and wastes: not used residues). Some residues are treated to turn them into valuable items or to diminish their polluting effects (e.g., the so-called by-products). About 1.56-1.63 million MT of by-products were used for different purposes (e.g. fertilization, animal feeding, fuel, substrates in greenhouses). However, the remainder (1.59-1.62 million MT) was discharged into environment causing pollution. About 1.07-1.2 million MT wastes came from major crop systems (banana, coffee, sugarcane and oil palm) whereas the remainder came from animal production systems (porcine and poultry production, slaughtering). These data are further compared to residues estimates for the 2001-2002 production season coming from the biggest crops activities. Unfortunately, most of the studied wastes contain high levels of moisture and low levels of protein, and also contain variable amounts of antinutritional factors (e.g., polyphenols, tannins, caffeine), high fibre levels and some toxic substances and pesticides. All these reasons may limit the use of these agricultural wastes for animal feeding, especially in fish feeds. The potential use of the major vegetable and animal residues in fish feeds is discussed based on their nutritional composition, on their amount available over the year and on their pollution risks. Other constraints to use these wastes in fish feeds are the extra costs of drying and, in most cases, of transportation from several dispersed locations. It was stated that most interesting wastes are rejected green banana and coffee pulp.     

Study of drying systems for the utilization of biodegradable municipal solid wastes as animal feed

The effectiveness of different drying systems used for the dehydration of certain fractions of biodegradable municipal solid wastes with a high moisture content (fruit and vegetable remains) was analyzed. Some tests using small amounts of the material were carried out in natural and forced convection ovens. For larger quantities of wastes, a discontinuous cabinet dryer and a continuous rotary dryer were used. With these dryers, the moisture content was reduced from 800 to 100 g kg(-1). It was verified that the continuous rotary dryer was the most efficient type of equipment studied, since it allowed a dried waste to be obtained with better nutritional and microbiological qualities and in accordance to the specifications of the products for animal feeding.     

Potential of chicken by-products as sources of useful biological resources

By-products from different animal sources are currently being utilised for beneficial purposes. Chicken processing plants all over the world generate large amount of solid by-products in form of heads, legs, bones, viscera and feather. These wastes are often processed into livestock feed, fertilizers and pet foods or totally discarded. Inappropriate disposal of these wastes causes environmental pollution, diseases and loss of useful biological resources like protein, enzymes and lipids. Utilisation methods that make use of these biological components for producing value added products rather than the direct use of the actual waste material might be another viable option for dealing with these wastes. This line of thought has consequently led to researches on these wastes as sources of protein hydrolysates, enzymes and polyunsaturated fatty acids. Due to the multi-applications of protein hydrolysates in various branches of science and industry, and the large body of literature reporting the conversion of animal wastes to hydrolysates, a large section of this review was devoted to this subject. Thus, this review reports the known functional and bioactive properties of hydrolysates derived from chicken by-products as well their utilisation as source of peptone in microbiological media. Methods of producing these hydrolysates including their microbiological safety are discussed. Based on the few references available in the literature, the potential of some chicken by-product as sources of proteases and polyunsaturated fatty acids are pointed out along with some other future applications.     

On the ASR and ASR thermal residues characterization of full scale treatment plant

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste.Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC – European Waste Catalogue – code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material.     

Washing of waste prior to landfilling

The main impact produced by landfills is represented by the release of leachate emissions. Waste washing treatment has been investigated to evaluate its efficiency in reducing the waste leaching fraction prior to landfilling. The results of laboratory-scale washing tests applied to several significant residues from integrated management of solid waste are presented in this study, specifically: non-recyclable plastics from source separation, mechanical-biological treated municipal solid waste and a special waste, automotive shredded residues. Results obtained demonstrate that washing treatment contributes towards combating the environmental impacts of raw wastes. Accordingly, a leachate production model was applied, leading to the consideration that the concentrations of chemical oxygen demand (COD) and total Kjeldahl nitrogen (TKN), parameters of fundamental importance in the characterization of landfill leachate, from a landfill containing washed wastes, are comparable to those that would only be reached between 90 and 220years later in the presence of raw wastes. The findings obtained demonstrated that washing of waste may represent an effective means of reducing the leachable fraction resulting in a consequent decrease in landfill emissions. Further studies on pilot scale are needed to assess the potential for full-scale application of this treatment.     

Toxicity of char residues produced in the co-pyrolysis of different wastes

Char residues produced in the co-pyrolysis of different wastes (plastics, pine biomass and used tyres) were characterized using chemical and toxicity assays. One part of the solid chars was submitted to extraction with dichloromethane (DCM) in order to reduce the toxicity of the char residues by removing organic contaminants. The different volatility fractions present in the extracted char (Char A) and in the raw char (Char B) were determined by progressive weight loss combustion. A selected group of heavy metals (Cd, Pb, Zn, Cu, Hg and As) was determined in both chars.The chars were subjected to the leaching test ISO/TS 21268 – 2, 2007 and the resulting eluates were further characterized by determining a group of inorganic parameters (pH, conductivity, Cd, Pb, Zn, Cu, Hg and As contents) and the concentrations of several organic contaminants (volatile aromatic hydrocarbons and alkyl phenols). An ecotoxicological characterization was also performed by using the bio-indicator Vibrio fischeri.The chemical and ecotoxicological results were analyzed according to the Council Decision 2003/33/CE and the criteria on the evaluation methods of waste ecotoxicity (CEMWE).The results obtained in this work indicated that the extraction with DCM is an effective method for the removal of organic contaminants of high to medium volatility from pyrolysis solid residues, thus decreasing their toxicity potential. Zn can be leached from the chars even after the DCM extraction treatment and can contribute to the ecotoxicity of the eluates obtained from chars.Both chars (treated and non treated with DCM) were classified as hazardous and ecotoxic wastes.     

Anaerobic co-digestion of the organic fraction of municipal solid waste with FOG waste from a sewage treatment plant: Recovering a wasted methane potential and enhancing the biogas yield

Anaerobic digestion is applied widely to treat the source collected organic fraction of municipal solid wastes (SC-OFMSW). Lipid-rich wastes are a valuable substrate for anaerobic digestion due to their high theoretical methane potential. Nevertheless, although fat, oil and grease waste from sewage treatment plants (STP-FOGW) are commonly disposed of in landfill, European legislation is aimed at encouraging more effective forms of treatment. Co-digestion of the above wastes may enhance valorisation of STP-FOGW and lead to a higher biogas yield throughout the anaerobic digestion process. In the present study, STP-FOGW was evaluated as a co-substrate in wet anaerobic digestion of SC-OFMSW under mesophilic conditions (37 °C). Batch experiments carried out at different co-digestion ratios showed an improvement in methane production related to STP-FOGW addition. A 1:7 (VS/VS) STP-FOGW:SC-OFMSW feed ratio was selected for use in performing further lab-scale studies in a 5 L continuous reactor. Biogas yield increased from 0.38 ± 0.02 L g VS_feed^?1 to 0.55 ± 0.05 L g VS_feed^?1 as a result of adding STP-FOGW to reactor feed. Both VS reduction values and biogas methane content were maintained and inhibition produced by long chain fatty acid (LCFA) accumulation was not observed. Recovery of a currently wasted methane potential from STP-FOGW was achieved in a co-digestion process with SC-OFMSW.     

Air pollution control residues from waste incineration: current UK situation and assessment of alternative technologies

Current disposal options for APC residues in the UK and alternative treatment technologies developed world-wide have been reviewed. APC residues are currently landfilled in the UK where they undergo in situ solidification, although the future acceptability of this option is uncertain because the EU waste acceptance criteria (WAC) introduce strict limits on leaching that are difficult to achieve. Other APC residue treatment processes have been developed which are reported to reduce leaching to below relevant regulatory limits. The Ferrox process, the VKI process, the WES-PHix process, stabilisation/solidification using cementitious binders and a range of thermal treatment processes are reviewed. Thermal treatment technologies convert APC residues combined with other wastes into inert glass or glass-ceramics that encapsulate heavy metals. The waste management industry will inevitably use the cheapest available option for treating APC residues and strict interpretation and enforcement of waste legislation is required if new, potentially more sustainable technologies are to become commercially viable.     

Evaluation of fruit-vegetable and fish wastes as alternative feedstuffs in pig diets

Fruit-vegetable and fish wastes were evaluated as potential feedstuffs for growing-finishing pigs. Wastes were collected from shops in the city of Salamanca (Spain) and their nutritional composition, mineral content and digestibility were determined. The dry matter of the wastes under study was relatively low (12% for fruit-vegetable waste and 26% for fish waste), but they presented all of the nutrient requirements for swine diets. The fish waste contained 58% crude protein, 22% ash, 19% ether extract and 1% crude fibre, whereas the fruit-vegetable waste contained 65% nitrogen free extract, 13% crude fibre, 12% crude protein, 8% ash and 2% ether extract. Waste digestibility decreased with temperature, and hence temperatures over 65 degrees C for fruit-vegetable waste and 105 degrees C for fish waste should not be used in the treatment to reduce the moisture and to ensure the microbiology quality. Therefore, two diets were formulated using linear programming. The analysed waste was included in approximately 20% of one of the diets, while another diet was formulated without any type of waste. These data showed that this part of biodegradable municipal waste could be managed as alternative feedstuffs in swine diets, reducing the amount of biodegradable municipal waste going to landfills.     

Recent trends and current practices for secondary processing of zinc and lead. Part I: lead recovery from secondary sources.

Implementation of stricter environmental laws and economic reasons has forced all the metallurgical industries to go for eco-friendly technologies to produce metal and other related products. However, generation of wastes is an integral part of metallurgical industries. If the wastes/residues are hazardous in nature, they generally have to be treated or/and disposed of in safe and designated dumping sites. If these wastes/residues are non-hazardous in nature, then they may be suitable for use as secondary raw material to recover metals such as lead, copper etc., which are in growing demand all over the world. The processing of lead secondaries is important because of their relative high metal content, as well as the low energy and cost involved in recovering the metal. This paper mainly focuses on the current practices and recent trends in the secondary processing of lead. Various processes, particularly hydrometallurgical ones, already developed or in the development stages, are discussed. Attempts made by various Council of Scientific and Industrial Research (CSIR) Laboratories including the National Metallurgical Laboratory (NML) and industries such as Binani Zinc to develop eco-friendly processes for the recovery of lead from secondary raw materials are also described.     

EU strategies and policies on soil and waste management to offset greenhouse gas emissions

Climate change has become an important political priority in the environmental field, and beyond. To revert the increase in the Earth’s temperature, developed country parties to the Kyoto Protocol committed to limit their greenhouse gas emissions. The 15 Member States that made up the European Community in 1997 have a combined reduction target of 8% in CO₂-equivalent emissions in the period 2008–2012 compared to 1990. The role of soil, both as a source and a sink for carbon, is particularly important. How can soil organic matter be maintained or increased? There is no single answer, and a broad range of options need to be explored. Among the different measures proposed, the promotion of organic input on arable land (crop residues, cover crops, farm yard manure, compost, sewage sludge) has been mentioned. The challenge is to ensure that organic wastes of good quality are used to increase soil organic matter in carbon depleted soils and that appropriate monitoring is established. On the waste management front, the European Commission intends to produce guidance for Member States on the management of biowaste that will take into account all related environmental issues, including soil aspects. As for monitoring, the European Commission has put forward legislation according to which Member States would have to identify the areas at risk of soil organic matter decline in their national territory. Such legislation should be regarded as a major step forward for Europe, as it would ensure a high level of soil protection across the Community. This development will have the potential to enable the kind of estimation, measurement or modelling of crop or grazing land management needed for accounting under Article 3.4 of the Kyoto Protocol.     

Fractionation of heavy metals in sludge from anaerobic wastewater stabilization ponds in southern Spain

The analysis of heavy metals is a very important task to assess the potential environmental and health risk associated with the sludge coming from wastewater treatment plants (WWTPs). However, it is necessary to apply sequential extraction techniques to obtain suitable information about their bioavailability or toxicity. In this paper, a sequential extraction scheme according to the Standard, Measurements and Testing Programme of the European Commission was applied to sludge samples collected from ten anaerobic wastewater stabilization ponds (WSPs) located in southern Spain. Al, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Ti and Zn were determined in the sludge extracts by inductively coupled plasma atomic emission spectrometry. In relation to current international legislation for the use of sludge for agricultural purposes, none of the metal concentrations exceeded maximum permitted levels. Overall, heavy metals were mainly associated with the two less-available fractions (34% oxidizable metal and 55% residual metal). Only Mn and Zn showed the highest share of the available (exchangeable and reducible) fractions (25-48%).     

Progress in used tyres management in the European Union: A review

The dynamic increase in the manufacture of rubber products, particularly those used in the automobile industry, is responsible for a vast amount of wastes, mostly in the form of used tyres, of which more than 17 million tonnes are produced globally each year. The widely differing chemical compositions and the cross-linked structures of rubber in tyres are the prime reason why they are highly resistant to biodegradation, photochemical decomposition, chemical reagents and high temperatures. The increasing numbers of used tyres therefore constitute a serious threat to the natural environment. The progress made in recent years in the management of polymer wastes has meant that used tyres are starting to be perceived as a potential source of valuable raw materials. The development of studies into their more efficient recovery and recycling, and the European Union's restrictive legal regulations regarding the management of used tyres, have led to solutions enabling this substantial stream of rubber wastes to be converted into energy or new polymer materials. In this article we present the relevant literature describing innovative organizational approaches in the management of used tyres in the European Union member countries and the possible uses of waste tyres as a source of raw materials or alternative fossil fuels.     

Scavenging solid wastes in Dar es Salaam,Tanzania

This paper deals with the scavenging of solid wastes in Dar es Salaam, Tanzania. It presents the generation, collection and disposal of wastes and the results of the scavenged wastes. Moreover, the socio-economic, health and organizational problems facing the scavengers are discussed. Three industries which use scavenged items as their raw materials have been surveyed and it is shown that the contribution by scavengers is high. The paper then analyses the raw materials and the employment which is generated by scavenging.     

BMP tests of source selected OFMSW to evaluate anaerobic codigestion with sewage sludge

The aim of this study is to characterize different types of source selected organic fraction of municipal solid waste (SS-OFMSW) in order to optimize the upgrade of a sewage sludge anaerobic digestion unit by codigestion. Various SS-OFMSW samples were collected from canteens, supermarkets, restaurants, households, fruit–vegetable markets and bakery shops. The substrates characterization was carried out getting traditional chemical–physical parameters, performing elemental analysis and measuring fundamental anaerobic digestion macromolecular compounds such as carbohydrates, proteins, lipids and volatile fatty acids. Biochemical methane potential (BMP) tests were conducted at mesophilic temperature both on single substrates and in codigestion regime with different substrates mixing ratios. The maximum methane yield was observed for restaurant (675 NmlCH₄/gVS) and canteens organic wastes (571 and 645 NmlCH₄/gVS). The best codigestion BMP test has highlighted an increase of 47% in methane production respect sewage sludge digestion.     

Biodegradation and flushing of MBT wastes

Mechanical–biological treatment (MBT) processes are increasingly being adopted as a means of diverting biodegradable municipal waste (BMW) from landfill, for example to comply with the EU Landfill Directive. However, there is considerable uncertainty concerning the residual pollution potential of such wastes. This paper presents the results of laboratory experiments on two different MBT waste residues, carried out to investigate the remaining potential for the generation of greenhouse gases and the flushing of contaminants from these materials when landfilled. The potential for gas generation was found to be between 8% and 20% of that for raw MSW. Pretreatment of the waste reduced the potential for the release of organic carbon, ammoniacal nitrogen, and heavy metal contents into the leachate; and reduced the residual carbon remaining in the waste after final degradation from ～320 g/kg dry matter for raw MSW to between 183 and 195 g/kg dry matter for the MBT wastes.     

A case study of waste management at the Northern Finnish pulp and paper mill complex of Stora Enso Veitsiluoto Mills

This work presents the current waste management system at the pulp and paper mill complex of Stora Enso Oyj Veitsiluoto Mills at Kemi, Northern Finland. This paper covers examples of case studies carried out at the mill and describes how the wastes and by-products are utilized as a neutralizing agent for acidic wastewaters (i.e., green liquor dregs from the causticizing process), as a hardener in filling mine cavities (i.e., ash from the fluidized bed boiler), as a landscaping agent (i.e., ash as well as the fibre clay from chemical wastewater treatment plant), as a hydraulic barrier material for landfills (i.e., fibre clay), and as a soil enrichment agent (i.e., calcium carbonate from the precipitated calcium carbonate plant). In addition, the wood waste from the wood-handling plant, sawmill, packaging pallet plant and from the groundwood mill, as well as the biosludge from the biological wastewater treatment plant, are all incinerated in the fluidized bed boiler for energy production. Due to effective utilization of the solid wastes generated at the mills, the annual amount of waste to be disposed of in the landfill has decreased between 1994 and 2004 from 42,990 to 6083 tonn (expressed as wet weight). The paper also gives an overview of the relevant European Union legislation on the forest industry and on waste management, as well as of the pulping process and of the generation of major solid wastes in the pulp and paper mills.     

Investigation of potentially toxic heavy metals in different organic wastes used to fertilize market garden crops

The benefits of using organic waste as fertilizer and soil amendment should be assessed together with the environmental impacts due to the possible presence of heavy metals (HMs). This study involved analysing major element and HM contents in raw and size-fractionated organic wastes (17 sewage sludges and composts) from developed and developing countries. The overall HM concentration pattern showed an asymmetric distribution due to the presence of some wastes with extremely high concentrations. HM concentrations were correlated with the size of cities or farms where the wastes had been produced, and HM were differentiated with respect to their origins (geogenic: Cr–Ni; anthropogenic agricultural and urban: Cu–Zn; anthropogenic urban: Cd–Pb). Size fractionation highlighted Cd, Cu, Zn and Pb accumulation in fine size fractions, while Cr and Ni were accumulated in the coarsest. HM associations with major elements revealed inorganic (Al, Fe, etc.) bearing phases for Cr and Ni, and sulfur or phosphorus species for Cd, Cu Pb and Zn.     

Production of feed and fertilizer from water Hyacinth plants in the tropics

Water hyacinth grows ubiquitously in natural water bodies in the tropics. If allowed to propagate without control, it can cause deterioration of water quality and create problems with water uses. However, water hyacinth has been used for wastewater treatment, and as an animal feed and soil conditioner. This paper reports a case study on silaging and composting of water hyacinth plants generated from ponds treating pig farm wastewater. The water hyacinth plants mixed with molasses and pig manure at the ratios of 85:10:5 (% wet weight) were found to be optimum for silage production; the silaging period was 28 days. The silaged products contained 16% protein and 18% dry matter, suitable for use as animal feed. The composted water hyacinth plants, whose raw materials included pig manure and leaves, contained N, P and K about 2.2, 1.5, and 0.8% (dry weight), respectively. An economic analysis of the two recycling options suggested that some benefits could be gained from these practices after 5 years of operation. These two options were found to be technically and economically feasible to be implemented at farm scale levels.