A mobile pollutant measurement laboratory—measuring gas phase and aerosol ambient concentrations with high spatial and temporal resolution

A mobile pollutant measurement laboratory was designed and built at the Paul Scherrer Institute (Switzerland) for the measurement of on-road ambient concentrations of a large set of trace gases and aerosol parameters with high time resolution (<15 s for most instruments), along with geographical and meteorological information. This approach allowed for pollutant level measurements both near traffic (e.g. in urban areas or on freeways/main roads) and at rural locations far away from traffic, within short periods of time and at different times of day and year. Such measurements were performed on a regular base during the project year of gas phase and aerosol measurements (YOGAM). This paper presents data measured in the Zürich (Switzerland) area on a late autumn day (6 November) in 2001. The local urban particle background easily reached 50 000 cm⁻³, with additional peak particle number concentrations of up to 400 000 cm⁻³. The regional background of the total particle number concentration was not found to significantly correlate with the distance to traffic and anthropogenic emissions of carbon monoxide and nitrogen oxides. On the other hand, this correlation was significant for the number concentration of particles in the size range 50–150 nm, indicating that the particle number concentration in this size range is a better traffic indicator than the total number concentration. Particle number size distribution measurements showed that daytime urban ambient air is dominated by high number concentrations of ultrafine particles (nanoparticles) with diameters <50 nm, which are immediately formed by traffic exhaust and thus belong to the primary emissions. However, significant variation of the nanoparticle mode was also observed in number size distributions measured in rural areas both at daytime and nighttime, suggesting that nanoparticles are not exclusively formed by primary traffic emissions. While urban daytime total number concentrations were increased by a factor of 10 compared to the nighttime background, corresponding factors for total surface area and total volume concentrations were 2 and 1.5, respectively.     

Urban scale modeling of particle number concentration in Stockholm

A three-dimensional dispersion model has been implemented over the urban area of Stockholm (35×35 km) to assess the spatial distribution of number concentrations of particles in the diameter range 3–400 nm. Typical number concentrations in the urban background of Stockholm is 10 000 cm⁻³, while they are three times higher close to a major highway outside the city and seven times higher within a densely trafficked street canyon site in the city center. The model, which includes an aerosol module for calculating the particle number losses due to coagulation and dry deposition, has been run for a 10-day period. Model results compare well with measured data, both in levels and in temporal variability. Coagulation was found to be of little importance in terms of time averaged concentrations, contributing to losses of only a few percent as compared to inert particles, while dry deposition yield particle number losses of up to 25% in certain locations. Episodic losses of up to 10% due to coagulation and 50% due to deposition, are found some kilometers downwind of major roads, rising in connection with low wind speed and suppressed turbulent mixing. Removal due to coagulation and deposition will thus be more significant for the simulation of extreme particle number concentrations during peak episodes.The study shows that dispersion models with proper aerosol dynamics included may be used to assess particle number concentrations in Stockholm, where ultrafine particles principally originate from traffic emissions. Emission factors may be determined from roadside measurements, but ambient temperature must be considered, as it has a strong influence on particle number emissions from vehicles.     

Characterization of on-road vehicle emission factors and microenvironmental air quality in Beijing,China

In this paper, we report the results and analysis of a recent field campaign in August 2007 investigating the impacts of emissions from transportation on air quality and community concentrations in Beijing, China. We conducted measurements in three different environments, on-road, roadside and ambient. The carbon monoxide, black carbon and ultrafine particle number emission factors for on-road light-duty vehicles are derived to be 95 g kg^?1-fuel, 0.3 g kg^?1-fuel and 1.8 × 10¹⁵ particles kg^?1-fuel, respectively. The emission factors for on-road heavy-duty vehicles are 50 g kg^?1-fuel, 1.3 g kg^?1-fuel and 1.1 × 10¹⁶ particles kg^?1-fuel, respectively. The carbon monoxide emission factors from this study agree with those derived from remote sensing and on-board vehicle emission testing systems in China. The on-road black carbon and particle number emission factors for Chinese vehicles are reported for the first time in the literature. Strong traffic impacts can be observed from the concentrations measured in these different environments. Most clear is a reflection of diesel truck traffic activity in black carbon concentrations. The comparison of the particle size distributions measured at the three environments suggests that the traffic is a major source of ultrafine particles. A four-day traffic control experiment conducted by the Beijing Government as a pilot to test the effectiveness of proposed controls was found to be effective in reducing extreme concentrations that occurred at both on-road and ambient environments.     

Decadal reductions of traffic emissions on a transit route in Austria – results of the Tauerntunnel experiment 1997

Real-world emissions of a traffic fleet on a transit route in Austria were determined in the Tauerntunnel experiment in October 1997. The total number of vehicles and the average speed was nearly the same on both measuring days (465 vehicles 30 min⁻¹ and 76 km h⁻¹ on the workday, 477 and 78 km h⁻¹ on Sunday). The average workday fleet contained 17.6% heavy-duty vehicles (HDV) and the average Sunday fleet 2.8% HDV resulting in up to four times higher emission rates per vehicle per km on the workday than on Sunday for most of the regulated components (CO₂, CO, NO_x, SO₂, and particulate matter-PM10). Emission rates of NMVOC accounted for 200 mg vehicle⁻¹ km⁻¹ on both days. The relative contributions of light-duty vehicles (LDV) and HDV to the total emissions indicated that aldehydes, BTEX (benzene, toluene, ethylbenzene, xylenes), and alkanes are mainly produced by LDV, while HDV dominated emissions of CO, NO_x, SO₂, and PM10. Emissions of NO_x caused by HDV were 16,100 mg vehicle⁻¹ km⁻¹ (as NO₂). Produced by LDV they were much lower at 360 mg vehicle⁻¹ km⁻¹. Comparing the emission rates to the results that were obtained by the 1988 experiment at the same place significant changes in the emission levels of hydrocarbons and CO, which accounted 1997 to only 10% of the levels in 1988, were noticed. However, the decrease of PM has been modest leading to values of 80 and 60% of the levels in 1988 on the workday and on Sunday, respectively. Emission rates of NO_x determined on the workday in 1997 were 3130 mg vehicle⁻¹ km⁻¹ and even higher than in 1988 (2630 mg vehicle⁻¹ km⁻¹), presumable due to the increase of the HD-traffic.     

Direct measurements and parameterisation of aerosol flux,concentration and emission velocity above a city

Articles have recently been published on aerosol size distributions and number concentrations in cities, however there have been no studies on transport of these particles. Eddy covariance measurements of vertical transport of aerosol in the size range 11 nm<D_p<3 μm are presented here. The analysis shows that typical average aerosol number fluxes in this size range vary between 9000 and 90,000 cm⁻² s⁻¹. With concentrations between 3000 and 20,000 cm⁻³ this leads to estimates of particle emission velocity between 20 and 75 mm s⁻¹. The relationships between number flux and traffic activity, along with emission velocity and boundary layer stability are demonstrated and parameterised. These are used to derive an empirical parameterisation for aerosol concentration in terms of traffic activity and stability. The main processes determining urban aerosol fluxes and concentrations are discussed and quantified where possible. The difficulties in parameterising urban activity are discussed.     

A new approach to in-situ determination of roadside particle emission factors of individual vehicles under conventional driving conditions

A method for continuous on-road measurements of particle number emissions for both diesel- and petrol-fuelled vehicles is presented. The setup allows the determination of particle number emission factors on an individual vehicle basis by the simultaneous measurement of CO₂ and particle concentrations. As an alternative to previous measurements on the kerbside, the sample is taken directly in the street, with the advantage of sampling in-situ within the exhaust plumes of passing vehicles, allowing the separation of the individual high-concentration plumes. The method was tested in two experiments that were conducted in the Gothenburg area. In the first study, which was performed at an urban roadside, we were able to determine particle emission factors from individual vehicles in a common car fleet passing the measurement site. The obtained emission factors were of the same order of magnitude (between 1.4 × 10¹² and 1.8 × 10¹⁴ particles km^?1) as values published in the recent literature for light duty vehicles. An additional on-road experiment was conducted at a rural road with four light duty reference vehicles (three of them petrol-powered and one diesel-powered) at driving speeds of 50 and 70 km h^?1, realised with different engine speeds. The results of the traffic emission studies show that the method is applicable provided that instruments with an adequate dynamic range are used and that the traffic is not too dense. In addition, the variability in particle emissions for a specified driving condition was estimated.     

Comparison of measured and model-calculated real-world traffic emissions

The quality of an emission calculation model based on emission factors measured on roller test stands and statistical traffic data was evaluated using source strengths and emission factors calculated from real-world exhaust gas concentration differences measured upwind and downwind of a motorway in southwest Germany. Gaseous and particulate emissions were taken into account. Detailed traffic census data were taken during the measurements. The results were compared with findings of similar studies.The main conclusion is the underestimation of CO and NO_x source strengths by the model. On the average, it amounts to 23% in case of CO and 17% for NO_x. The latter underestimation results from an undervaluation by 22% of NO_x emission factors of heavy-duty vehicles (HDVs). There are significant differences between source strengths on working days and weekends because of the different traffic split between light-duty vehicles (LDVs) and HDVs. The mean emission factors of all vehicles from measurements are 1.08 g km⁻¹ veh⁻¹ for NO_x and 2.62 g km⁻¹ veh⁻¹ for CO. The model calculations give 0.92 g km⁻¹ veh⁻¹ for NO_x and 2.14 g km⁻¹ veh⁻¹ for CO.The source strengths of 21 non-methane hydrocarbon (NMHC) compounds quantified are underestimated by the model. The ratio between the measured and model-calculated emissions ranges from 1.3 to 2.1 for BTX and up to 21 for 16 other NMHCs. The reason for the differences is the insufficient knowledge of NMHC emissions of road traffic.Particulate matter emissions are dominated by ultra-fine particles in the 10–40 nm range. As far as aerosols larger than 29 nm are concerned, 1.80×10¹⁴ particles km⁻¹ veh⁻¹ are determined for all vehicles, 1.22×10¹⁴ particles km⁻¹ veh⁻¹ and an aerosol volume of 0.03 cm³ km⁻¹ veh⁻¹ are measured for LDVs, and for HDVs 7.79×10¹⁴ particles km⁻¹ veh⁻¹ and 0.41 cm³ km⁻¹ veh⁻¹ are calculated. Traffic-induced turbulence has been identified to have a decisive influence on exhaust gas dispersion near the source.     

Change of the ambient particle size distribution in East Germany between 1993 and 1999

Size distribution of particle number concentrations in the geometric equivalent diameter range 0.01–2.5 μm were determined in three communities, Zerbst, Bitterfeld and Hettstedt of the state of Sachsen-Anhalt in Eastern Germany, in the first half of 1993 and 1999. A Mobile Aerosol Spectrometer (MAS) consisting of a differential mobility particle spectrometer (DMPS) and a laser aerosol spectrometer (LAS-X) were used for size-selective particle number concentration measurements from which mass concentrations were derived based on an apparent mean density of the ambient aerosol of the closely situated city of Erfurt.The total number concentration was governed by ultra-fine particles (<0.1 μm) (81% in 1993 and 90% in 1999) and 0.1–0.5 μm size fraction dominates total mass concentration (approximately 80%). While the mass concentration of fine particles (PM2.5) decreased from 39 to 19 μg m⁻³, the geometric means of total number concentration showed constant concentration (13.3×10³ cm⁻³ in 1993 and 13.3×10³ cm⁻³ in 1999, p=0.975) and the geometric means of number concentration of ultra-fine particles (UP) between 10 and 30 nm increased from 5.9×10³ to 8.2×10³ cm⁻³ from 1993 to 1999 (p=0.016). The temporal changes of number and mass concentrations in the three communities are similar. The clear shift to smaller particle sizes within this six years period was caused by changes of the most prominent sources, traffic and domestic heating, since formerly dominating industries in Bitterfeld and Hettstedt had vanished grossly.     

Using NOx and CO monitoring data to indicate fine aerosol number concentrations and emission factors in three UK conurbations

It is increasingly accepted that although exposure to elevated concentrations of PM₁₀ is associated with an increased risk of mortality and morbidity, the relationship may not be causal. Rather, there is evidence that number concentrations may be a more appropriate metric than mass concentrations in evaluating health risk. Number concentrations are not routinely monitored and spatial and temporal patterns are poorly quantified. CO and NO_x are co-pollutants with their major urban source in common with fine particles, i.e. road vehicle emissions; are routinely monitored in many cities and are also related to ill health. Datasets of particle number concentration measurements from approximately month-long field campaigns in Manchester, Edinburgh and Birmingham (UK) are compared with simultaneous concentrations of CO and NO_x from nearby fixed monitors. It was found that it might be possible to reliably predict particle number concentrations (diameters>100 nm) on an hourly basis in Manchester city centre from knowledge of NO_x or CO concentrations alone. The influences of meteorology, spatial variability in emissions and lack of co-location upon the correlations are investigated using cluster analysis. The cluster analysis revealed that these relationships may vary between cities and are dependent upon monitor location but in ways that can be ascribed. For two out of three sites there existed a linear relationship between average cluster aerosol and gas concentrations. This indicates that although airmass aging disrupts the short-term linear relationship, the relationship in the average survives. An emission ratio of particles (approx. 100–500 nm diameter) to NO_x of approximately 50 cm⁻³ ppb⁻¹ was estimated in Manchester and Birmingham. Particle mass spectrometry measurements indicated that organic compounds dominated these particles and an emission rate of 0.58 ton km⁻² a⁻¹ of organic particulate matter from road transport has been estimated for the Greater Manchester conurbation.     

Dilution and aerosol dynamics within a diesel car exhaust plume—CFD simulations of on-road measurement conditions

Vehicle particle emissions are studied extensively because of their health effects, contribution to ambient PM levels and possible impact on climate. The aim of this work was to obtain a better understanding of secondary particle formation and growth in a diluting vehicle exhaust plume using 3-d information of simulations together with measurements. Detailed coupled computational fluid dynamics (CFD) and aerosol dynamics simulations have been conducted for H₂SO₄–H₂O and soot particles based on measurements within a vehicle exhaust plume under real conditions on public roads.Turbulent diffusion of soot and nucleation particles is responsible for the measured decrease of number concentrations within the diesel car exhaust plume and decreases coagulation rates. Particle size distribution measurements at 0.45 and 0.9 m distance to the tailpipe indicate a consistent soot mode (particle diameter D_p∼50 nm) at variable operating conditions. Soot mode number concentrations reached up to 10¹³ m⁻³ depending on operating conditions and mixing.For nucleation particles the simulations showed a strong sensitivity to the spatial dilution pattern, related cooling and exhaust H₂SO_4(g). The highest simulated nucleation rates were about 0.05–0.1 m from the axis of the plume. The simulated particle number concentration pattern is in approximate accordance with measured concentrations, along the jet centreline and 0.45 and 0.9 m from the tailpipe. Although the test car was run with ultralow sulphur fuel, high nucleation particle (D_p⩽15 nm) concentrations (>10¹³ m⁻³) were measured under driving conditions of strong acceleration or the combination of high vehicle speed (>140 km h⁻¹) and high engine rotational speed (>3800 revolutions per minute (rpm)).Strong mixing and cooling caused rapid nucleation immediately behind the tailpipe, so that the highest particle number concentrations were recorded at a distance, x=0.45 m behind the tailpipe. The simulated growth of H₂SO₄–H₂O nucleation particles was unrealistically low compared with measurements. The possible role of low and semi-volatile organic components on the growth processes is discussed. Simulations for simplified H₂SO₄–H₂O–octane–gasoil aerosol resulted in sufficient growth of nucleation particles.     

Investigation of the motor vehicle exhaust contribution to primary fine particle organic carbon in urban air

Motor vehicle (MV) emissions and ambient particle concentrations under a variety of situations were studied in Toronto and Vancouver, Canada. Petroleum biomarkers (i.e., hopanes and steranes) were used to determine the fraction of fine particle organic carbon (OC) attributed to primary particles in MV exhaust. Source profiles obtained from a tunnel and from direct tailpipe emissions were applied to ambient measurements at locations ranging from rush hour traffic to a regional background site. The greatest amount of MV OC, 4.0 μgC m⁻³ out of 9.1 μgC m⁻³ or 43%, was observed 75 m south of a commuter highway during a period that included morning rush hour. Monthly estimates of MV-OC were determined for a downtown Toronto monitoring site for 2 years. Total OC concentrations were greater in the summer, due to secondary OC, but the amount of MV-OC did not exhibit a strong seasonal pattern. However, on a per cent basis, MV contributions from primary OC emissions were greatest in the winter (15–20%) and smallest in the summer (10–15%) with a two-year average of 14% of the OC or about 5% of the PM_2.5.     

Identification and assessment of ship emissions and their effects in the harbour of Göteborg,Sweden

The effect of ship emissions in the urban environment of Göteborg has been studied by multivariate analysis. The simultaneous measurements of relevant gases and sub-micron particles make identification of ship plumes possible. Increased concentrations of these species due to ship emissions are quantified for ships entering the inner part of the harbour. Annual depositions of SO₂ and NO₂ are estimated to be 220 and 115 kg km⁻² yr⁻¹, respectively. Exposure of transient particles (less than 0.1 μm in diameter) to this part of the harbour increased by a factor of 3 in number concentration when a ship plume was recorded. Ni, Pb, V and Zn are shown to have positive correlation with NO emissions from ships.     

Real-world emission factors of fifteen carbonyl compounds measured in a Hong Kong tunnel

Real-world vehicle emissions of carbonyls were determined in summer and winter of 2003 at the Shing Mun Tunnel, Hong Kong. Fifteen carbonyl species have been analyzed in this study. The total measured carbonyls emission factors ranged from 21.7 to 68.9 mg veh⁻¹ km⁻¹ among different measurement periods, with an average of 35.8±11.9 mg veh⁻¹ km⁻¹. Higher carbonyl emissions were found to be associated with a high proportion of diesel-fueled vehicles. Total measured carbonyl emissions from Diesel-fueled Vehicle (DV, 71.5 mg veh⁻¹ km⁻¹) were about 7 times higher than those from Non-Diesel-fueled Vehicle (NDV, 10 mg veh⁻¹ km⁻¹). The five carbonyls with the largest DV emission factor were, in decreasing order, formaldehyde (38.3 mg veh⁻¹ km⁻¹), acetaldehyde (11.4 mg veh⁻¹ km⁻¹), acetone (5.3 mg veh⁻¹ km⁻¹), crotonaldehyde (5.2 mg veh⁻¹ km⁻¹) and benzaldehyde (2.0 mg veh⁻¹ km⁻¹). These five carbonyl compounds together accounted for 87% of the sum of all DV carbonyl emission factors. For NDV, the five most abundant carbonyls in NDV emission at the tunnel were, in decreasing order, formaldehyde (3.5 mg veh⁻¹ km⁻¹), acetone (1.8 mg veh⁻¹ km⁻¹), methyl ethyl ketone (1.6 mg veh⁻¹ km⁻¹), m,p-tolualdehyde (1.0 mg veh⁻¹ km⁻¹) and acetaldehyde (mg veh⁻¹ km⁻¹). They accounted for 85% of the sum of all NDV carbonyl emission factors.     

Particulate size distributions and mass measured at a motorway during the BAB II campaign

From 1 May to 25 May 2001, the BAB II campaign was carried out at the motorway BAB (656) near Heidelberg. Atmospheric concentrations of particulate matter and gases were measured together with the meteorological conditions. This paper is focused on the particulate matter measured upwind and downwind from the motorway at ground level. In order to determine the source contribution from the motorway traffic, it was necessary to measure upwind and downwind simultaneously due to variations in background concentrations. The particle number contribution from the motorway was found to be 35,000 particles cm⁻³ for particles with diameters close to 20 nm and 5000 particles cm⁻³ for particles with diameters close to 70 nm. Bimodal size distributions were observed on the downwind side, whereas the upwind side showed unimodal size distributions. For particulate mass, it can be estimated that the contribution from the motorway to the PM₁ concentrations is in a range 0.6–1.3 μg m⁻³ for the chosen measurement sites approximately 60 m from the road at a height of 6 m. The soot measurements showed diurnal variation; however, the upwind downwind difference was not measured. Correlation factors showed good correlation between total particle number and number of particles with diameters below 80 nm, CO and NO. There was no correlation between particle number and PM₁₀, which is due to the observation that particle number was dominated by the 20 nm particles.     

Pre- and post-catalyst-, fuel-, velocity- and acceleration-dependent benzene emission data of gasoline-driven EURO-2 passenger cars and light duty vehicles

The benzene emission characteristics of six gasoline-driven EURO-2 vehicles, three passenger cars and three light duty vehicles, have been determined by time-resolved chemical ionization mass spectrometry. Aliquots of the exhaust gas were monitored pre- and post-catalyst with two independently operating mass spectrometers. Each vehicle was driven with two different fuels having benzene contents of 1 and 2 vol%. Seven driving cycles—including the European (EDC) and the US (FTP-75) driving cycle—with a total driving time of about 8800 s were studied. Herein, we discuss the average emission characteristics of the entire fleet at transient driving in the velocity range of 0–150 km h⁻¹. The conversion efficiencies of the involved catalytic systems were deduced from the pre- and post-catalyst data. On average, the vehicles showed optimal benzene conversion efficiencies (>95%) in the velocity range of 30–90 km h⁻¹. When driving below 20 or above 100 km h⁻¹ reduced benzene conversion was found (80–82%). No benzene conversion was observed when driving above 130 km h⁻¹. In contrast, the post-catalyst benzene emissions exceeded those of the untreated exhaust gas by 19–49%. Thus on an average, benzene was formed across the catalysts under these conditions. In addition, the influence of the benzene content of the gasoline on the tail-pipe emissions was also studied. The use of the gasoline with 1 vol% benzene instead of 2 vol% induced a 20–30% reduction of the post-catalyst emissions when driving below 50 km h⁻¹. The fuel effect became smaller above 100 km h⁻¹ and was even negative at high engine load (>130 km h⁻¹). Thus under these conditions, when benzene is formed across the catalyst, the amount of the emitted benzene was independent of the benzene level of the fuel.     

Aerosol number size distributions within the exhaust plume of a diesel and a gasoline passenger car under on-road conditions and determination of emission factors

A new setup has been developed and built to measure number size distributions of exhaust particles and thermodynamic parameters under real traffic conditions. Measurements have been performed using a diesel and a gasoline passenger car driving with different speeds and engine conditions. Significant number of nucleation mode particles was found only during high load conditions, i.e. high car and engine speeds behind the diesel car. The number concentration of soot mode particles varied within a factor of two for different engine conditions while the concentration of nucleation mode particles varied up to two orders of magnitude. The results show that roadside measurements are still quite different from those behind the tailpipe. Beside dilution transformation processes within the first meter behind the tailpipe also play an important role, such as nucleation and growth. Emission factors were calculated and compared with those obtained by other studies. Emission factors for particles larger than 25 nm (primary emissions) varied within 1.1 × 10¹⁴ km^?1 and 2.7 × 10¹⁴ km^?1 for the diesel car and between 0.6 × 10¹² km^?1 and 3.5 × 10¹² km^?1 for the gasoline car. The advantage of these measurements is the exhaust dilution under atmospheric conditions and the size-resolved measurement technique to divide into primary emitted and secondary formed particles.     

Carbon content of atmospheric aerosols in a residential area during the wood combustion season in Sweden

Carbonaceous aerosol particles were observed in a residential area with wood combustion during wintertime in Northern Sweden. Filter samples were analyzed for elemental carbon (EC) and organic carbon (OC) content by using a thermo-optical transmittance method. The light-absorbing carbon (LAC) content was determined by employing a commercial Aethalometer and a custom-built particle soot absorption photometer. Filter samples were used to convert the optical signals to LAC mass concentrations. Additional total PM₁₀ mass concentrations and meteorological parameters were measured. The mean and standard deviation mass concentrations were 4.4±3.6 μg m⁻³ for OC, and 1.4±1.2 μg m⁻³ for EC. On average, EC accounted for 10.7% of the total PM₁₀ and the contribution of OC to the total PM₁₀ was 35.4%. Aethalometer and custom-built PSAP measurements were highly correlated (R²=0.92). The hourly mean value of LAC mass concentration was 1.76 μg m⁻³ (median 0.88 μg m⁻³) for the winter 2005–2006. This study shows that the custom-built PSAP is a reliable alternative for the commercial Aethalometer with the advantage of being a low-cost instrument.     

Characterisation of fresh particulate vehicular exhausts near a Paris high flow road

Simultaneous continuous measurements of PM_2.5, PM₁₀, black carbon mass (BCae), Black smoke (BS) and particle number density (N) were conducted in the close vicinity of a high traffic road around Paris during a three-month period beginning in August 1997. In parallel some aerosol collection was performed on filters in order to assess the black carbon (BC), organic carbon (OC) and water soluble organic fractions (WSOC) of the freshly emitted traffic aerosols. The high hourly concentrations of PM_2.5 (39±20 μg m⁻³), BCae (14±7 μg m⁻³), and N (220,000±115,000 cm⁻³), were found to be well correlated with each other. On average PM_2.5 represented 66±13% of PM₁₀ and appears to be composed primarily of BC (43±20%). On the contrary no correlation was found between PM_2.5 and the coarse (PM₁₀–PM_2.5) mass fractions which was attributed to resuspension processes by vehicles. Black carbon mass concentrations obtained from both filter analyses (BC) and Aethalometre data (BCae) show a good agreement suggesting that the Aethalometre calibration based on a black carbon specific attenuation coefficient (σ) of 19 m² g⁻¹ is well adapted to nearby roadside measurements. Daily BC (used as a surrogate for fine particles) concentrations and wind speed were found to be anti-correlated. Average daily variations of BC could be related to traffic intensity and regime as well as to the boundary layer height. As expected for freshly emitted traffic aerosols, filter analyses indicated a high BC/TC ratio (29±5%) and a low mean WSOC/OC ratio (12.5±5%) for the bulk aerosol. For these two ratios no day/night differences were observed, the sampling station being probably too close to traffic to evidence photochemical modification of the aerosol phase. Finally, a linear relationship was found between BC and BS hourly concentrations (BC=0.10×BS+1.18; r²=0.93) which offers interesting perspectives to retrieve BC concentrations from existing BS archives.     

Differences in airborne particle and gaseous concentrations in urban air between weekdays and weekends

Airborne particle number concentrations and size distributions as well as CO and NO_x concentrations monitored at a site within the central business district of Brisbane, Australia were correlated with the traffic flow rate on a nearby freeway with the aim of investigating differences between weekday and weekend pollutant characteristics. Observations over a 5-year monitoring period showed that the mean number particle concentration on weekdays was (8.8±0.1)×10³ cm⁻³ and on weekends (5.9±0.2)×10³ cm⁻³—a difference of 47%. The corresponding mean particle number median diameters during weekdays and weekends were 44.2±0.3 and 50.2±0.2 nm, respectively. The differences in mean particle number concentration and size between weekdays and weekends were found to be statistically significant at confidence levels of over 99%. During a 1-year period of observation, the mean traffic flow rate on the freeway was 14.2×10⁴ and 9.6×10⁴ vehicles per weekday and weekend day, respectively—a difference of 48%. The mean diurnal variations of the particle number and the gaseous concentrations closely followed the traffic flow rate on both weekdays and weekends (correlation coefficient of 0.86 for particles). The overall conclusion, as to the effect of traffic on concentration levels of pollutant concentration in the vicinity of a major road (about 100 m) carrying traffic of the order of 10⁵ vehicles per day, is that about a 50% increase in traffic flow rate results in similar increases of CO and NO_x concentrations and a higher increase of about 70% in particle number concentration.     

Iron,manganese and copper emitted by cargo and passenger trains in Zürich (Switzerland): Size-segregated mass concentrations in ambient air

Particle emissions caused by railway traffic have hardly been investigated in the past, due to their obviously minor influence on air quality compared to automotive traffic. In this study, emissions related to particle abrasion from wheels and tracks were investigated next to a busy railway line in Zürich (Switzerland), where trains run nearly exclusively with electrical locomotives. Hourly size-segregated aerosol samples (0.1–1, 1–2.5 and 2.5–10 μm) were collected with a rotating drum impactor (RDI) and subsequently analyzed by synchrotron radiation X-ray fluorescence spectrometry (SR-XRF). In this way, hourly elemental mass concentrations were obtained for chromium, manganese, iron and copper, which are the elements most relevant for railway abrasion. Additionally, daily aerosol filters were collected at the same site as well as at a background site for subsequent analysis by gravimetry and wavelength dispersive XRF (WD-XRF). Railway related ambient air concentrations of iron and manganese were calculated for the coarse (2.5–10 μm) and fine (<2.5 μm) particle fraction by means of a Mn/Fe ratio investigation. The comparison to train type and frequency data showed that 75% and 60% of the iron and manganese mass concentrations related to cargo and passenger trains, respectively, were found in the coarse mode. The railway related iron mass concentration normalized by the train frequency ranges between 10 and 100 ng m⁻³ h iron in 10 m distance to the tracks, depending on train type. It is estimated that the personal exposure next to a busy railway line above ground is more than a magnitude lower than inside a subway station.