上流式厌氧污泥床滤层反应器处理鸡粪混合液离心出水

本研究采用上流式厌氧污泥床滤层反应器对蛋鸡场鸡粪混合液离心出水进行处理,试验结果:在中温25℃,进水COD_(cr)18000mg/L和氨氮1600mg/L的条件下,COD_(cr)去除率74.08%,BOD_5去除率83.78%,水力停留时间26.15h,容积负荷15.60kg·COD_(cr)/m~3·d,产气率0.52m~3/去除km·COD_(cr).反应器运行状况良好.     

厌氧-好氧法处理味精废水的试验

等电点-离子交换法生产味精所产生的废水,COD_(Cr)在20000mg/l左右,属于高浓度有机废水。该废水经厌氧(水停留48h)、稀释(三倍)、好氧(水停留12h)、生物炭(水停留6.6h)处理,COD_(Cr)从16274.3 mg/l下降到208mg/l,去除率为98.7％(扣除稀释水的影响,则为96.2％)。BOD_5从9806 mg/l下降到60 mg/l以下,出水为无色、透明、无臭,溶解氧为1.2 mg/l。试验结果表明,厌氧-好氧法处理味精废水是一种有机物去除率高,运转费用低的较为理想的方法。     

味精浓废水生物处理优化工艺

本文阐述两相厌氧消化法与缺氧—厌氧消化法处理味精浓废水的比较试验.进水为6×10~4mg/L～8×10~4mg/L时,两相厌氧消化法COD去除率为78%,产气率为0.15m~3/kgCOD,CH_4含量为50%.缺氧—厌氧消化法COD去除率为82.2%,产气率为0.23m~3/kgCOD,CH.含量达65%.两种方法均可使出水pH值由3.2上升至7.0以上.氯离子和氨氮的去除不明显.综合上述结果与运行管理的稳定程度均是缺氧——厌氧消化法优于两相厌氧消化法.     

UASB反应器处理生活污水的自接种启动

本试验利用未沉淀的生活污水(COD在432mg/L左右)在7℃～22℃温度下自接种启动容积为5L的升流式厌氧污泥层反应器.初始有机容积负荷为1.75kgCOD/m~3·d,水力停留时间为5.9h.运行57天时出现了颗粒污泥,此时污泥负荷为0.33kgCOD/kgVSS·d.106天后反应器达到稳定的处理效果.当温度在20℃左右,HRT为6h,COD去除率达81.2%,出水COD低于100mg/L.培养出的颗粒污泥呈黑色,粒径在0.5mm～3mm之间,比重为1.04, SVI在15左右,有较好的沉降性和产甲烷活性.污泥中产甲烷菌主要是素氏甲烷丝菌.     

水解酸化与序列间歇式活性污泥法(SBR)结合工艺处理餐饮废水

分别研究了SBR法,水解酸化预处理及工艺组合对餐饮油脂废水的处理效果,确定了最佳处理工艺.同时,实验考察了曝气时间、污泥沉降比、溶解氧等因素与处理效果的关系,从而确定最佳的反应条件.结果表明,在曝气时间为2 h、SV为30%、DO为3 mg.L-1的条件下,SBR工艺处理餐饮油脂废水中COD、动植物油脂的平均去除率分别达到91.2%、82.5%;经水解酸化预处理,出水COD、动植物油脂平均浓度分别为1062.90 mg.L-1、50.66 mg.L-1,去除率均值分别为36.9%、83.5%;经水解酸化+SBR组合工艺处理后,废水出水COD平均浓度为93.66 mg.L-1,去除率高达94.8%,出水动植物油脂浓度为4.9 mg.L-1,去除率为98.25%.     

缺氧—SBR工艺处理焦化废水

对焦化废水进行曝气吹脱,10h氨氮去除率达73．7％,用缺氧－SBR工艺处理焦化废水,进水浓度为COD1474mg/L,NH3-N826.8mg/L时,缺氧SRT10h,SBR曝气10h,沉降2h,出水COD186mg/L,NH3-N290.5mg/L,去除率分别达到87．83％,64．9％。     

固定化细胞处理难降解有机废水

本文首先对琼脂、明胶、海藻酸钙、聚乙烯酰和丙烯醇铵5种固定化细胞载体的性能进行了比较,然后用固定化细胞分别对含难降解有机成份的洗衣粉废水和四环素废水进行了处理试验.结果表明,聚乙烯醇凝胶是其中较为合适的固定化细胞载体;洗衣粉废水中的LAS浓度为40mg/L～70mg/L时,3h内LAS可降解90%以上;在固定化细胞作为产甲烷相的二相厌氧工艺中,产酸相和产甲烷相停留时间分别为3h和24h时,四环素废水的COD去除率可达73%左右.     

物化预处理-水解酸化-接触氧化法处理选矿废水

对某浮选厂浮选废水进行混凝沉淀+活性碳吸附预处理,然后进入生化系统,厌氧池、好氧池停留时间为10h.结果证明:进水COD为400～700mg/L,出水74～145 mg/L,去除率达75.8%以上,首次成功地将生物法应用到铅锌选矿废水的处理,若对该工艺进行适当调整,完全可以使出水达到排放或回用标准.     

MAP法和SBR法处理垃圾渗滤液的研究

氨氮浓度为2570.45mg·l-1的垃圾渗滤液经磷酸铵镁沉淀法处理后的处理出水中TN约为79.35mg·l-1,TP约为10.35mg·l-1,电导率约为78000μS·cm-1.研究用SBR法进一步处理处理出水的可行性.用常规的活性污泥,探讨了污水的含盐量和系统运行周期对TN,TP和COD去除率的影响.结果表明,当垃圾渗滤液处理出水和生活污水以1: 4混合后,TN约为48.0mg·l-1,TP约为6.0mg·l-1,COD约为1150.0mg·l-1,电导率略为15000μS·cm-1.运行的适宜周期为12h(其中厌氧2.0h,好氧5.0h,缺氧3.5h,后耗氧0.5h,沉淀排水和闲置1.0h).在此条件下,出水TN小于15 mg·l-1,TP小于1.0mg·l-1,COD约为110mg·l-1.TN,TP和COD去除率分别约为77%,87%和90%.     

采用絮凝—接触氧化法处理酿酒行业废水

采用絮凝-接触氧化法处理酿酒行业废水,原废水CODcr浓度为1627-2334mg/L,SS浓度为2095-2301mg/L,BOD5浓度为981-1005mg/L,色度为80-110倍,用絮凝-接触氧化法处理后,CODer浓度为280-295mg/L,SS浓度为178-199mg/L,CODcr浓度为145-150mg/L,色度为20-25倍,CODcr平均去除率为85%。悬浮物平均去除率为91%,BOD5平均去除率为85%,色度平均去除率为77%,各项指标符合国家排废标准。     

反渗透法处理土霉素结晶母液的研究

土霉素结晶母液经调节ｐＨ值后的水经预滤后进行反渗透处理,可使污染物去除率达９９％以上,排放水ＣＯＤｃｒ１５３ｍｇ／Ｌ、ＢＯＤ１０７ｍｇ／Ｌ水可以回用或达标排放。     

啤酒废水处理工程设计

桂林漓泉有限公司污水处理厂经过改造,采用UASB－SBR工艺进行啤酒废水处理。处理后出水水质指标：COD＝35．7mg／L,BOD＝10mg/L,达到GB89790－1996《国家污水综合排放标准》的一级标准。改造后的工具具有投资少,占地面积小,结构紧凑,高效低耗,出水水质好,剩余污泥少,可回收能源等优点。     

Biodegradation of wastewater of Najafgarh drain,Delhi using autochthonous microbial consortia : a laboratory study

There are seventeen drains, which discharge their untreated urban and industrial wastewaters into the Delhi segment of river Yamuna. The Najafgarh drain is the first and the largest drain, and it alone contributes 1667.84 mld i.e. 60% of the total wastewater discharge into the river Yamuna and as such add 81.36 tons of BOD load per day. As per the available data approximately 95% of the wastewater of this drain is biodegradable. In the present study, an attempt has been made to reduce the BOD load and COD levels of wastewater of Najafgarh drain using autochthonous microbial consortium. During this study the raw wastewater samples were treated for 6 h time interval with different concentration of consortium. It was observed that by increasing the existing microbial population in the wastewater sample by 150-200% there is a significant decrease in BOD and COD levels. Finally, BOD/COD ratios before and after biotreatment have been analyzed to assess the efficacy of the natural consortium.     

絮凝-光催化处理实际染料废水的研究

采用絮凝-光催化氧化工艺成功地处理了实际染料废水;研究了COD光催化降解动力学。COD和BOD5浓度分别为2169mg／L、295mg／L的染料废水,经絮凝-光催化处理后,出水COD和BOD5分别为214mg／L、18．5mg／L,去除率分别为90．1％、93．7％。向光催化体系中加入H2O2,可促进COD与BOD5的去除。该工艺可处理高浓度染料废水。     

森林公园污水回用改造工程设计的案例分析

昆明市某森林公园污水回用工程处理规模1000t／d,于2007建成使用,水源为市政管网截污,使用一段时间后出水各项指标均超过回用水质标准33％～170％,针对出现问题采用MBR工艺进行了改造。改造后系统运行稳定,出水COD≤50mg／L、BOD≤6mg,／L、SS≤10mg／L、NH4-N≤5mg／L、TP≤0．5mg／L、TN≤15mg／L,均优于《城市污水再生利用景观环境用水水质》标准中观赏性景观环境用水水景类水质标准,同时运行费用较原工艺降低18％,为0．847元/m^3,实现了工程改造的预期目标。     

二氧化氯催化氧化处理直接大红染料

研究了ClO2化学氧化体系和ClO2催化氧化体系。实验结果表明:单用ClO2化学氧化处理COD为3 400mg/L的直接大红染料配制废水时,最佳反应pH值为1,氧化剂ClO2经济用量为400 mg/L废水,反应时间为10 min,COD去除率可达85.9%,氧化指数(COD削减量∶ClO2投加量)=7。当ClO2与自制催化剂所组成的催化氧化体系用于对直接大红染料配制废水的处理时,最佳反应pH值为2左右,氧化剂ClO2经济用量为600 mg/L废水,反应时间为6 min,COD去除率可达96.6%,氧化指数=6。结果表明,ClO2催化氧化法是一种新型高效的处理难降解废水的技术,有着广阔的应用前景。     

Achieving biodegradability enhancement and acute biotoxicity removal through the treatment of pharmaceutical wastewater using a combined internal electrolysis and ultrasonic irradiation technology

Actual pharmaceutical wastewater was treated using a combined ultrasonic irradiation (US) and iron/coke internal electrolysis (Fe/C) technology. A significant synergetic effect was observed, showing that ultrasonic irradiation dramatically enhanced the chemical oxygen demand (COD) removal efficiencies by internal electrolysis. The effects of primary operating factors on COD removal were evaluated systematically. Higher ultrasonic frequency and lower pH values as well as longer reaction time were favorable to COD removal. The ratio of biochemical oxygen demand (BOD) and COD (B/C) of the wastewater increased from 0.21 to 0.32 after US-Fe/C treatment. An acute biotoxicity assay measuring the inhibition of bioluminescence indicated that the wastewater with overall toxicity of 4.3 mg-Zn²⁺·L^-1 was reduced to 0.5 mg-Zn²⁺·L^-1 after treatment. Both the raw and the treated wastewater samples were separated and identified. The types of compounds suggested that the increased biodegradability and reduced biotoxicity resulted mainly from the destruction of N,N-2 dimethyl formamide and aromatic compounds in the pharmaceutical wastewater.     

Partial anammox achieved in full scale biofilm process for typical domestic wastewater treatment

• A full scale biofilm process was developed for typical domestic wastewater treatment. • The HRT was 8 h and secondary sedimentation tank was omitted. • Candidatus Brocadia were enriched in the HBR with an abundance of 2.89%. • Anammox enabled a stable ammonium removal of ~15% in the anoxic zone. The slow initiation of anammox for treating typical domestic wastewater and the relatively high footprint of wastewater treatment infrastructures are major concerns for practical wastewater treatment systems. Herein, a 300 m³/d hybrid biofilm reactor (HBR) process was developed and operated with a short hydraulic retention time (HRT) of 8 h. The analysis of the bacterial community demonstrated that anammox were enriched in the anoxic zone of the HBR process. The percentage abundance of Candidatus Brocadia in the total bacterial community of the anoxic zone increased from 0 at Day 1 to 0.33% at Day 130 and then to 2.89% at Day 213. Based upon the activity of anammox bacteria, the removal of ammonia nitrogen (NH₄⁺-N) in the anoxic zone was approximately 15%. This showed that the nitrogen transformation pathway was enhanced in the HBR system through partial anammox process in the anoxic zone. The final effluent contained 12 mg/L chemical oxygen demand (COD), 0.662 mg/L NH₄⁺-N, 7.2 mg/L total nitrogen (TN), and 6 mg/L SS, indicating the effectiveness of the HBR process for treating real domestic wastewater.