Nuclear power in the 21st century: Challenges and possibilities

The current situation and possible future developments for nuclear power—including fission and fusion processes—is presented. The fission nuclear power continues to be an essential part of the low-carbon electricity generation in the world for decades to come. There are breakthrough possibilities in the development of new generation nuclear reactors where the life-time of the nuclear waste can be reduced to some hundreds of years instead of the present time-scales of hundred thousand of years. Research on the fourth generation reactors is needed for the realisation of this development. For the fast nuclear reactors, a substantial research and development effort is required in many fields—from material sciences to safety demonstration—to attain the envisaged goals. Fusion provides a long-term vision for an efficient energy production. The fusion option for a nuclear reactor for efficient production of electricity has been set out in a focussed European programme including the international project of ITER after which a fusion electricity DEMO reactor is envisaged.     

Biosolids management strategies: an evaluation of energy production as an alternative to land application

Currently, more than half of the biosolids produced within the USA are land applied. Land application of biosolids introduces organic contaminants into the environment. There are potential ecological and human health risks associated with land application of biosolids. Biosolids may be used as a renewable energy source. Nutrients may be recovered from biosolids used for energy generation for use as fertilizer. The by-products of biosolids energy generation may be used beneficially in construction materials. It is recommended that energy generation replace land application as the leading biosolids management strategy.     

Energy crops on landfills: functional,environmental, and costs analysis of different landfill configurations

The cultivation of energy crops on landfills represents an important challenge for the near future, as the possibility to use devalued sites for energy production is very attractive. In this study, four scenarios have been assessed and compared with respect to a reference case defined for northern Italy. The scenarios were defined taking into consideration current energy crops issues. In particular, the first three scenarios were based on energy maximisation, phytotreatment ability, and environmental impact, respectively. The fourth scenario was a combination of these characteristics emphasised by the previous scenarios. A multi-criteria analysis, based on economic, energetic, and environmental aspects, was performed. From the analysis, the best scenario resulted to be the fourth, with its ability to pursue several objectives simultaneously and obtain the best score relatively to both environmental and energetic criteria. On the contrary, the economic criterion emerges as weak, as all the considered scenarios showed some limits from this point of view. Important indications for future designs can be derived. The decrease of leachate production due to the presence of energy crops on the top cover, which enhances evapotranspiration, represents a favourable but critical aspect in the definition of the results.     

Biohythane production from organic wastes: present state of art

The economy of an industrialized country is greatly dependent on fossil fuels. However, these nonrenewable sources of energy are nearing the brink of extinction. Moreover, the reliance on these fuels has led to increased levels of pollution which have caused serious adverse impacts on the environment. Hydrogen has emerged as a promising alternative since it does not produce CO₂ during combustion and also has the highest calorific value. The biohythane process comprises of biohydrogen production followed by biomethanation. Biological H₂ production has an edge over its chemical counterpart mainly because it is environmentally benign. Maximization of gaseous energy recovery could be achieved by integrating dark fermentative hydrogen production followed by biomethanation. Intensive research work has already been carried out on the advancement of biohydrogen production processes, such as the development of suitable microbial consortium (mesophiles or thermophiles), genetically modified microorganism, improvement of the reactor designs, use of different solid matrices for the immobilization of whole cells, and development of two-stage process for higher rate of H₂ production. Scale-up studies of the dark fermentation process was successfully carried out in 20- and 800-L reactors. However, the total gaseous energy recovery for two stage process was found to be 53.6 %. From single-stage H₂ production, gaseous energy recovery was only 28 %. Thus, two-stage systems not only help in improving gaseous energy recovery but also can make biohythane (mixture of H₂ and CH₄) concept commercially feasible.     

Creating markets for combined heat and power and clean distributed generation in New York State

Combined heat and power (CHP) is the simultaneous production of electrical or mechanical power and thermal energy from in a single process. Because thermal output from the generation of electricity is captured and utilized onsite, CHP systems can achieve efficiencies from 60% to as high as 90%. In contrast generation of electric power at sites remote from the loads served often results in efficiencies of 33% or less due to losses in generation and transmission and distribution of the power to ultimate end users. A well designed CHP system is the essence of energy efficiency. It may also provide significant environmental benefits. However, the full promise of CHP for improving the efficiency and productivity of businesses and the quality of the environment is unlikely to be realized given the current market structure and regulatory environment in which CHP projects are forced to compete. This paper examines the market structure and regulatory obstacles that hinder the development of more robust markets for CHP in New York State.     

碱熔法生产二氧化锆污染的综合治理

采用新型反应器及胶凝除硅、直接酸溶重结晶、直接煅烧等技术对二氧化锆的生产工艺进行了改革 ,降低了原材料消耗及能耗 ,减少了废液排放量 ,并将回收的废物加工成副产品白炭黑 ,在生产过程中防治污染。     

Effect of biogas generation on radon emissions from landfills receiving radium-bearing waste from shale gas development

Dramatic increases in the development of oil and natural gas from shale formations will result in large quantities of drill cuttings, flowback water, and produced water. These organic-rich shale gas formations often contain elevated concentrations of naturally occurring radioactive materials (NORM), such as uranium, thorium, and radium. Production of oil and gas from these formations will also lead to the development of technologically enhanced NORM (TENORM) in production equipment. Disposal of these potentially radium-bearing materials in municipal solid waste (MSW) landfills could release radon to the atmosphere. Risk analyses of disposal of radium-bearing TENORM in MSW landfills sponsored by the Department of Energy did not consider the effect of landfill gas (LFG) generation or LFG control systems on radon emissions. Simulation of radon emissions from landfills with LFG generation indicates that LFG generation can significantly increase radon emissions relative to emissions without LFG generation, where the radon emissions are largely controlled by vapor-phase diffusion. Although the operation of LFG control systems at landfills with radon source materials can result in point-source atmospheric radon plumes, the LFG control systems tend to reduce overall radon emissions by reducing advective gas flow through the landfill surface, and increasing the radon residence time in the subsurface, thus allowing more time for radon to decay. In some of the disposal scenarios considered, the radon flux from the landfill and off-site atmospheric activities exceed levels that would be allowed for radon emissions from uranium mill tailings.

Implications: Increased development of hydrocarbons from organic-rich shale formations has raised public concern that wastes from these activities containing naturally occurring radioactive materials, particularly radium, may be disposed in municipal solid waste landfills and endanger public health by releasing radon to the atmosphere. This paper analyses the processes by which radon may be emitted from a landfill to the atmosphere. The analyses indicate that landfill gas generation can significantly increase radon emissions, but that the actual level of radon emissions depend on the place of the waste, construction of the landfill cover, and nature of the landfill gas control system.     

The dynamic analysis of renewable energy’s contribution to the dimensions of sustainable development and energy security

In sustainable development, energy is critical in human activities and shapes a sustainable future. Thus, it is an unignorable element in human development. This paper analyzes the contributions of renewable energy sources (RES)’s to the economic, environmental, and social dimensions of sustainable development. Moreover, we add energy security as a possible fourth dimension into the analysis. For the sample size, we limit the countries members of the OECD and run generalized methods of moments for the period from 1995 to 2015. This method can produce efficient estimators under the problems of endogeneity, omitted-variable bias, measurement errors, and heteroscedastic residuals. According to the results, RES has a small reducing effect (?.007%) on output in the Cobb-Douglas production function for the economic dimension. We found that RES has a positive contribution to the environmental dimension and abates the level of carbon emission (?.093%). RES also confirms the inverted-U shape of environmental Kuznets curve. In the social dimension, RES improves human development and a 1% increase in RES consumption causes to .0045% increase in human development. In the last contribution, RES has a positive effect on sustainable energy supply security in the context of electricity generation (.032%). Although the effects of RES on the environment, social, and energy security are significant, they are limited. These limitations point to barriers that can be overcome over time. Our conclusions recommend that these effects might flourish with technical developments and political support in the long run. Furthermore, public awareness, rising income level, and economies of scale are also beneficial in this process. As a result, RES might be an excellent source for a sustainable future and development. Especially, RES might have remarkable contributions to the 7th, 11th, 12th, and 13th goals of sustainable development.

     

农业废弃物的资源化利用

我国的农业资源浪费和破坏现象十分严重,解决这一问题的根本途径是开展农业废弃物的资源化利用,它是农业可持续发展的重要方面。本文在分析了农业废弃物资源化利用的理论基础后,讨论了农业废弃物的主要资源化利用途径和支持与保障体系。     

Bio-Ethanol Production from Non-Food Parts of Cassava (<Emphasis Type="Italic">Manihot esculenta</Emphasis> Crantz)

Global climate issues and a looming energy crisis put agriculture under pressure in Sub-Saharan Africa. Climate adaptation measures must entail sustainable development benefits, and growing crops for food as well as energy may be a solution, removing people from hunger and poverty without compromising the environment. The present study investigated the feasibility of using non-food parts of cassava for energy production and the promising results revealed that at least 28% of peels and stems comprise dry matter, and 10 g feedstock yields >8.5 g sugar, which in turn produced >60% ethanol, with pH ≈ 2.85, 74-84% light transmittance and a conductivity of 368 mV, indicating a potential use of cassava feedstock for ethanol production. Thus, harnessing cassava for food as well as ethanol production is deemed feasible. Such a system would, however, require supportive policies to acquire a balance between food security and fuel.     

On the way to the creation of next generation photoactive materials

Introduction

Transition from first- to second-generation photocatalysts has followed the notion that greater absorption of light in the visible region would yield greater spectral sensitivity and greater photoactivity. Though a promising strategy, in practice, it did not meet expectation because of various side issues, which in many cases has led to loss of photoactivity and chemical reactivity. This article examines some earlier notions that arose from applications of different metal oxides (e.g., TiO₂, ZnO, MgO among others) that made these oxides good photocatalysts in many processes.

Discussion

Phenomena that proved relevant in developing next generation photoactive materials are considered: the dependence of the activity of photocatalysts on the band gap energy, the spectral variations of the activity of photoactive materials, and the spectral variations of selectivity of photoactive materials. The tendency to decrease the energy of actinic photons through doping in forming second-generation photocatalysts is completely opposite the fundamental observation in first-generation photocatalysts whereby the activity increased with increasing band gap energy. Extension of spectral sensitivity of second-generation photoactive materials also caused a decrease of their photoactivity; hence, some notions are reconsidered to produce next(third) generation photoactive materials.

Summary

The article proposes the following concepts to develop next generation photocatalysts: (1) multi(two)-photon excitation of photoactive materials with lower energy photons to achieve the same excited state as with higher energy photons, (2) utilization of heterojunctions to drive electronic processes in the desired direction, and (3) selective photoexcitation of localized electronic states to gain better selectivity.     

Scenario Development as a Basis for Formulating a Research Program on Future Agriculture: A Methodological Approach

To increase the awareness of society to the challenges of global food security, we developed five contrasting global and European scenarios for 2050 and used these to identify important issues for future agricultural research. Using a scenario development method known as morphological analysis, scenarios were constructed that took economic, political, technical, and environmental factors into account. With the scenarios as a starting point future challenges were discussed and research issues and questions were identified in an interactive process with stakeholders and researchers. Based on the outcome of this process, six socioeconomic and biophysical overarching challenges for future agricultural were formulated and related research issues identified. The outcome was compared with research priorities generated in five other research programs. In comparison, our research questions focus more on societal values and the role of consumers in influencing agricultural production, as well as on policy formulation and resolving conflicting goals, areas that are presently under-represented in agricultural research. The partly new and more interdisciplinary research priorities identified in Future Agriculture compared to other programs analyzed are likely a result of the methodological approach used, combining scenarios and interaction between stakeholders and researchers.     

染料废水处理技术的研究与进展

概述了含染料废水处理方法的研究现状和最新进展 ,尤其是在物化法 (包括辐射法、吸附 萃取法、磁分离法、混凝沉降法和氧化法 )、生物法 (好氧 厌氧氧化 -还原序列反应器、固定化微生物降解、膜生物反应器 )及生物 -物化联合法 (生物吸附剂、生物活性炭、厌氧折流板反应池 -生物接触氧化池 -混凝沉淀 -砂滤池处理工艺、水解酸化 -接触氧化法等 )中的新技术的研究现状 ,新方法、材料、工艺的应用方面 ,对提高此类废水的处理效果有重要的理论和实际意义     

Energy and emission benefits of chicken manure biogas production: a case study

Studies on the production of biogas of different organic materials in an anaerobic environment are being carried out all over the world. The most important parameters in these researches can be listed as raw material potential, production processes, economic analyses, and environmental effects. Chicken manure is one of the raw materials used in biogas production. In this study, in addition to the analysis of biogas and energy production potential from chicken manure, greenhouse gas emissions were analyzed to evaluate environmental effects. In Turkey, chicken manure is not adequately processed and causes environmental pollution. The model biogas plant and potential energy generation were researched in this field study. The pilot plant produces 8.58 million m³ of biogas per year by processing about 110 thousand tons of waste. It produces 17 GWh/year of electricity and 16 GWh/year of thermal energy, as well as reducing CO₂ greenhouse gas emissions by 13.86 thousand tons/year.

     

脱硫反应器及其应用

脱硫反应器是脱硫工艺的核心装置 ,其技术和脱硫指标将制约和决定脱硫工艺的效率。在分析中 ,比较全面地介绍和比较了近年来主要的烟气脱硫反应器设备和研究成果及应用情况 ,指出了脱硫反应器的发展方向     

Degradation of 2-chlorophenol via a hydrogenotrophic biofilm under different reductive conditions

This research studies the 2-chlorophenol (2-CP) degradation by the hydrogenotrophic biofilm cultivated in three silicone-tube membrane bioreactors under the conditions of denitrification (DN), sulfate-reduction (DS) and dechlorination (DC). Experimental results showed that after acclimation for more than four months with 2-CP, the respective 2-CP removal efficiency was 95% in DN, 94% in DS and 95% in DC reactors, under the condition of influent 2-CP 25 mg/l with hydraulic retention time (HRT) of 15 h. The metabolic pathway of 2-CP was different in different reactors. The 2-CP was thought to be utilized as carbon and energy source in DN and DS reactors, while the dechlorination occurred in the DC reactor in lack of nitrate and sulfate. The pH dramatically affected the 2-CP degradation in all reactors. Experimental results showed that the optimal pH range was around 6+/-0.2 in DN, 7+/-0.2 in DS, and 5.8-7.2 in DC reactors. Both nitrate and sulfate inhibited the 2-CP dechlorination, but the inhibition levels were different. Nitrate completely inhibited the dechlorination at once, while sulfate took a longer time to reach complete inhibition, only after the bacteria were adapted to the sulfate-reducing condition. Both inhibitions were accomplished by taking the place of 2-CP as electron acceptors. H2 served as an electron donor for dechlorination of 2-CP. The dechlorination was apparently stopped when lacking H2 and another pathway was responsible for the 2-CP degradation.     

The Potential Environmental Impact of Waste from Cellulosic Ethanol Production

Abstract

The increasing production of ethanol has been established as an important contributor to future energy independence. Although ethanol demand is increasing, a growing economic trend in decreased profitability and resource conflicts have called into question the future of grain-based ethanol production. Growing emphasis is being placed on utilizing cellulosic feedstocks to produce ethanol, and the need for renewable resources has made the development of cellulosic ethanol a national priority. Cellulosic ethanol production plants are being built in many areas of the United States to evaluate various feed-stocks and processes. The waste streams from many varying processes that are being developed contain a variety of components. Differences in ethanol generation processes and feedstocks are producing waste streams unique to biofuel production, which could be potentially harmful to the environment if adequate care is not taken to manage those risks. Waste stream management and utilization of the cellulosic ethanol process are equally important components of the development of this industry.     

Biogas production from anaerobic digestion of food waste and relevant air quality implications

Biopower can diversify energy supply and improve energy resiliency. Increases in biopower production from sustainable biomass can provide many economic and environmental benefits. For example, increasing biogas production through anaerobic digestion of food waste would increase the use of renewable fuels throughout California and add to its renewables portfolio. Although a biopower project will produce renewable energy, the process of producing bioenergy should harmonize with the goal of protecting public health. Meeting air emission requirements is paramount to the successful implementation of any biopower project. A case study was conducted by collecting field data from a wastewater treatment plant that employs anaerobic codigestion of fats, oils, and grease (FOG), food waste, and wastewater sludge, and also uses an internal combustion (IC) engine to generate biopower using the biogas. This research project generated scientific information on (a) quality and quantity of biogas from anaerobic codigestion of food waste and municipal wastewater sludge, (b) levels of contaminants in raw biogas that may affect beneficial uses of the biogas, (c) removal of the contaminants by the biogas conditioning systems, (d) emissions of NO_x, SO₂, CO, CO₂, and methane, and (e) types and levels of air toxics present in the exhausts of the IC engine fueled by the biogas. The information is valuable to those who consider similar operations (i.e., co-digestion of food waste with municipal wastewater sludge and power generation using the produced biogas) and to support rulemaking decisions with regards to air quality issues for such applications.

Implications: Full-scale operation of anaerobic codigestion of food waste with municipal sludge is viable, but it is still new. There is a lack of readily available scientific information on the quality of raw biogas, as well as on potential emissions from power generation using this biogas. This research developed scientific information with regard to quality and quantity of biogas from anaerobic co-digestion of food waste and municipal wastewater sludge, as well as impacts on air quality from biopower generation using this biogas. The need and performance of conditioning/pretreatment systems for biopower generation were also assessed.     

Development of an environmentally benign process for the production of fatty acid methyl esters

The production of fatty acid methyl esters (FAME) is an important intermediate step in oleochemistry. The oleochemical production route starts with the renewable raw materials fat and oil and ends at fatty alcohols and different special products. Fatty acid methyl esters can be formed at mild reaction temperatures by transesterification of natural triglycerides (fats and oils). This contribution will show the development of a continuous process which is considering the main principles of production integrated environmental protection. The main advantages of this process are low energy consumption and minimal waste production. The process alternatives are shown and a scope on future problems which have to be solved to reach a real additional improvement of the fatty acid methyl esters production is given.     

The fate and importance of organics in drinking water treatment: a review

In the pioneer days, the main driving forces for research of organics in drinking water treatment (DWT) were human health risks and optimisation of technology. The focus was on natural organic matter (NOM) structure, disinfection by-products (DBPs) formation, NOM removal by means of coagulation, adsorption, and oxidation, and development of the most efficient water treatment trains. Surprisingly, after decades of research, rapid development of analytical techniques and progress in risk assessment, the same driving forces are still in the limelight — although the topics have changed slightly. The attention switched from trihalomethanes to a new generation of DBPs. The definition of hydrophilic/hydrophobic NOM depends on the technique used for characterisation. It has become evident that numerous organic compounds can threaten water supply sources. Some of them had been ignored or overlooked in the past, but have recently been detected by advanced analytical tools even in drinking water. Prioritisation becomes priority per se. As far as processes are concerned, mainstream research has been following three lines: fouling mechanisms, application of hybrid processes and interactions between synthetic organic chemicals, other water constituents and materials used in DWT. Significant development has been made in membrane technology. This paper presents a broad overview of the recent organics research. Although the state-of-the-art technologies seem to have an answer to each and every question raised, it is still necessary to deal with specific problems on a case-by-case basis mainly due to the unique nature of NOM and different xenobiotics that may appear in various types of waters. In the end, human health risk, which derives from the presence/absence of organics, is only the tip of the iceberg — underneath lies a whole new universe — the socio-economic aspect of water treatment and quality that deserves much more attention.