Photocatalytic degradation of dichlorvos in aqueous TiO<Subscript>2</Subscript> suspensions

Introduction  

In the present work, we explored the kinetics of dichlorvos (2,2-dichlorvinyl dimethyl phosphate, DDVP) decay through UV-A light-induced TiO₂ photocatalysis at pH 4 and 9, and the formation of degradation intermediates and final products under specific experimental conditions. Experimental observations and theoretical considerations allowed us to suggest the degradation mechanism of DDVP by the UV/TiO₂ process in aqueous solution.     

Photocatalytic decomposition of methanol over La/TiO<Subscript>2</Subscript> materials

Lanthanum-modified TiO₂ photocatalysts (0.2–1.5 wt% La) were investigated in the methanol decomposition in an aqueous solution. The photocatalysts were prepared by the common sol-gel method followed by calcination. The structural (X-ray diffraction, Raman, X-ray photoelectron spectroscopy), textural (N₂ physisorption), and optical properties (diffuse reflectance spectroscopy, photoelectrochemical measurements) of all synthetized nanomaterials were correlated with photocatalytic activity. Both pure TiO₂ and La-doped TiO₂ photocatalysts proved higher yields of hydrogen in comparison to photolysis. The photocatalyst with optimal amount of lanthanum (0.2 wt% La) showed almost two times higher amount of hydrogen produced at the same time as in the presence of pure TiO₂. The photocatalytic activity increased with both increasing photocurrent response and decreasing amount of lattice and surface O species. It has been shown that both direct and indirect mechanisms of methanol photocatalytic oxidation participate in the production of hydrogen. Both direct and indirect mechanisms take part in the formation of hydrogen.     

Photocatalytic reduction of carbon dioxide over Cu/TiO<Subscript>2</Subscript> photocatalysts

The photocatalytic reduction of CO₂ with H₂O was investigated using Cu/TiO₂ photocatalysts in aqueous solution. For this purpose, Cu/TiO₂ photocatalysts (with 0.2, 0.9, 2, 4, and 6 wt.% of Cu) have been synthesized via sol-gel method. The photocatalysts were extensively characterized by means of inductively coupled plasma optical emission spectrometry (ICP-OES), N₂ physisorption (BET), XRD, UV-vis DRS, FT-IR, Raman spectroscopy, TEM-EDX, and photoelectrochemical measurements. The as-prepared photocatalysts contain anatase as a major crystalline phase with a crystallite size around 13 nm. By increasing the amount of Cu, specific surface area and band gap energy decreased in addition to the formation of large agglomeration of CuO. Results revealed that the photocatalytic reduction of CO₂ decreased in the presence of Cu/TiO₂ in comparison to pure TiO₂, which might be associated to the formation of CuO phase acting as a recombination center of generated electron-hole pair. Decreasing of photoactivity can also be connected with a very low position of conduction band of photocatalysts with high Cu content, which makes H₂ production necessary for CO₂ reduction more difficult.     

Solar-driven photocatalytic treatment of diclofenac using immobilized TiO<Subscript>2</Subscript>-based zeolite composites

The study is aimed at evaluating the potential of immobilized TiO₂-based zeolite composite for solar-driven photocatalytic water treatment. In that purpose, TiO₂-iron-exchanged zeolite (FeZ) composite was prepared using commercial Aeroxide TiO₂ P25 and iron-exchanged zeolite of ZSM5 type, FeZ. The activity of TiO₂-FeZ, immobilized on glass support, was evaluated under solar irradiation for removal of diclofenac (DCF) in water. TiO₂-FeZ immobilized in a form of thin film was characterized for its morphology, structure, and composition using scanning electron microscopy/energy-dispersive x-ray spectroscopy (SEM/EDX). Diffuse reflectance spectroscopy (DRS) was used to determine potential changes in band gaps of prepared TiO₂-FeZ in comparison to pure TiO₂. The influence of pH, concentration of hydrogen peroxide, FeZ wt% within the composite, and photocatalyst dosage on DCF removal and conversion efficiency by solar/TiO₂-FeZ/H₂O₂ process was investigated. TiO₂-FeZ demonstrated higher photocatalytic activity than pure TiO₂ under solar irradiation in acidic conditions and presence of H₂O₂.     

Ferrate(VI) enhanced photocatalytic oxidation of pollutants in aqueous TiO<Subscript>2</Subscript> suspensions

Background, aim and scope  

Photocatalytic oxidation using UV irradiation of TiO₂ has been studied extensively and has many potential industrial applications, including the degradation of recalcitrant contaminants in water and wastewater treatment. A limiting factor in the oxidation process is the recombination of conduction band electrons (e ⁻ _cb) with electron holes (h_vb⁺) on the irradiated TiO₂ surface; thus, in aqueous conditions, the presence of an effective electron scavenger will be beneficial to the efficiency of the oxidation process. Ferrate (FeO₄²⁻) has received much recent attention as a water treatment chemical since it behaves simultaneously as an oxidant and coagulant. The combination of ferrate [Fe(VI)] with UV/TiO₂ photocatalysis offers an oxidation synergism arising from the Fe(VI) scavenging of e ⁻ _cb and the corresponding beneficial formation of Fe(V) from the Fe(VI) reduction. This paper reviews recent studies concerning the photocatalytic oxidation of problematic pollutants with and without ferrate.     

A mini-review on rare earth metal-doped TiO<Subscript>2</Subscript> for photocatalytic remediation of wastewater

Titanium dioxide (TiO₂) has been considered a useful material for the treatment of wastewater due to its non-toxic character, chemical stability and excellent electrical and optical properties which contribute in its wide range of applications, particularly in environmental remediation technology. However, the wide band gap of TiO₂ photocatalyst (anatase phase, 3.20 eV) limits its photocatalytic activity to the ultraviolet region of light. Besides that, the electron-hole pair recombination has been found to reduce the efficiency of the photocatalyst. To overcome these problems, tailoring of TiO₂ surface with rare earth metals to improve its surface, optical and photocatalytic properties has been investigated by many researchers. The surface modifications with rare earth metals proved to enhance the efficiency of TiO₂ photocatalyts by way of reducing the band gap by shifting the working wavelength to the visible region and inhibiting the anatase-to-rutile phase transformations. This review paper summarises the attempts on modification of TiO₂ using rare earth metals describing their effect on the photocatalytic activities of the modified TiO₂ photocatalyst.     

Photocatalytic decomposition of N<Subscript>2</Subscript>O over g-C<Subscript>3</Subscript>N<Subscript>4</Subscript>/WO<Subscript>3</Subscript> photocatalysts

Although the nitrous oxide belongs among three of the most contributing greenhouse gases to global warming, it is quite neglected by photocatalytic society. The g-C₃N₄ and WO₃ composites were therefore tested for the photocatalytic decomposition of N₂O for the first time. The pure photocatalysts were prepared by simple calcination of precursors, and the composites were prepared by mixing of suspension of pure components in water followed by calcination. The structural (X-ray diffraction, X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy), textural (N₂ physisorption), and optical properties (diffuse reflectance spectroscopy, photoluminescence spectroscopy, photoelectrochemical measurements) of all composites were correlated with photocatalytic activity. The experimental results and results from characterization techniques confirmed creation of Z-scheme in the WO₃/g-C₃N₄ composites, which was confirmed by hydroxyl radicals’ trapping measurements. The photocatalytic decomposition of N₂O was carried out in the presence of UVA light (peak intensity at 365 nm) and the 1:2 WO₃/g-C₃N₄ composite was the most active one, but the photocatalytic activity was just negligibly higher than that of pure WO₃. This is caused by relatively weak interaction between WO₃ and g-C₃N₄ which was revealed from XPS.     

Effects of realistic concentrations of TiO<Subscript>2</Subscript> and ZnO nanoparticles in <Emphasis Type="Italic">Prochilodus lineatus</Emphasis> juvenile fish

The impact of nanoparticles on fish health is still a matter of debate, since nanotechnology is quite recent. In this study, freshwater benthonic juvenile fish Prochilodus lineatus were exposed through water to three concentrations of TiO₂ (0.1, 1, and 10 μg l^?1) and ZnO (7, 70, and 700 μg l^?1) nanoparticles, as well as to a mixture of both (TiO₂ 1 μg l^?1?+?ZnO 70 μg l^?1) for 5 and 30 days. Nanoparticle characterization revealed an increase of aggregate size in the function of concentration, but suspensions were generally stable. Fish mortality was high at subchronic exposure to 70 and 700 μg l^?1 of ZnO. Nanoparticle exposure led to decreased acetylcholinesterase activity either in the muscle or in the brain, depending on particle composition (muscle—TiO₂ 10 μg l^?1; brain—ZnO 7 and 700 μg l^?1), and protein oxidative damage increased in the brain (ZnO 70 μg l^?1) and gills (ZnO 70 μg l^?1 and mixture) but not in the liver. Exposed fish had more frequent alterations in the liver (necrosis, vascular congestion, leukocyte infiltration, and basophilic foci) and gills (hyperplasia and epithelial damages, e.g., epithelial disorganization and epithelial loss) than the control fish. Thus, predicted concentrations of TiO₂ and ZnO nanoparticles caused detectable effects on P. lineatus that may have important consequences to fish health. But, these effects are much more subtle than those usually reported in the scientific literature for high concentrations or doses of metal nanoparticles.     

Study on the removal of elemental mercury from simulated flue gas by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-CeO<Subscript>2</Subscript>/AC at low temperature

Fe₂O₃ and CeO₂ modified activated coke (AC) synthesized by the equivalent-volume impregnation were employed to remove elemental mercury (Hg⁰) from simulated flue gas at a low temperature. Effects of the mass ratio of Fe₂O₃ and CeO₂, reaction temperature, and individual flue gas components including O₂, NO, SO₂, and H₂O (g) on Hg⁰ removal efficiency of impregnated AC were investigated. The samples were characterized by Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Results showed that with optimal mass percentage of 3 % Fe₂O₃ and 3 % CeO₂ on Fe3Ce3/AC, the Hg⁰ removal efficiency could reach an average of 88.29 % at 110 °C. Besides, it was observed that O₂ and NO exhibited a promotional effect on Hg⁰ removal, H₂O (g) exerted a suppressive effect, and SO₂ showed an insignificant inhibition without O₂ to some extent. The analysis of XPS indicated that the main species of mercury on used Fe3Ce3/AC was HgO, which implied that adsorption and catalytic oxidation were both included in Hg⁰ removal. Furthermore, the lattice oxygen, chemisorbed oxygen, and/or weakly bonded oxygen species made a contribution to Hg⁰ oxidation.     

Photocatalytic degradation of phenol using Ag core-TiO<Subscript>2</Subscript> shell (Ag@TiO<Subscript>2</Subscript>) nanoparticles under UV light irradiation

Ag@TiO₂ nanoparticles were synthesized by one pot synthesis method with postcalcination. These nanoparticles were tested for their photocatalytic efficacies in degradation of phenol both in free and immobilized forms under UV light irradiation through batch experiments. Ag@TiO₂ nanoparticles were found to be the effective photocatalysts for degradation of phenol. The effects of factors such as pH, initial phenol concentration, and catalyst loading on phenol degradation were evaluated, and these factors were found to influence the process efficiency. The optimum values of these factors were determined to maximize the phenol degradation. The efficacy of the nanoparticles immobilized on cellulose acetate film was inferior to that of free nanoparticles in UV photocatalysis due to light penetration problem and diffusional limitations. The performance of fluidized bed photocatalytic reactor operated under batch with recycle mode was evaluated for UV photocatalysis with immobilized Ag@TiO₂ nanoparticles. In the fluidized bed reactor, the percentage degradation of phenol was found to increase with the increase in catalyst loading.     

Fouling mitigation and cleanability of TiO<Subscript>2</Subscript> photocatalyst-modified PVDF membranes during ultrafiltration of model oily wastewater with different salt contents

In the present study, TiO₂-coated ultrafiltration membranes were prepared and used for oily water filtration (droplet size <?2 μm). The aim of this work was to investigate the effect of different salt contents on fouling and filtration properties of neat and TiO₂-coated membranes during oil-in-water emulsion filtration. The effect of the TiO₂ coating on the flux, surface free energy, and retention values was measured and compared with the neat membrane values. The cleanability of the fouled TiO₂-coated membranes by UV irradiation was also investigated by measuring flux recovery and contact angles, and the chemical changes during cleaning were characterized by ATR-IR. It was found that increasing the salt content of the model wastewaters, oil-in-water emulsions, increased the zeta potential and the size of the droplets. The presence of the TiO₂ coating decreases the membrane fouling during oily emulsion filtration compared to the neat membrane, due to the hydrophilicity of the coating regardless of the salt content of the emulsions. The neat and coated membrane oil retention was similar, 96?±?2%. The coated membrane can be effectively cleaned with UV irradiation without additional chemicals and a significant flux recovery can be achieved. Monitoring of the cleaning process by following the membrane surface wettability and ATR-IR measurements showed that the recovery of flux does not mean the total elimination of the oil layer from the membrane surface.     

Use of carbon-based composites to enhance performance of TiO<Subscript>2</Subscript> for the simultaneous removal of nitrates and organics from aqueous environments

The simultaneous photocatalytic removal of nitrate from aqueous environment in presence of organic hole scavenger using TiO₂ has long been explored. However, the use of unmodified TiO₂ in such reaction resulted in non-performance or release of significant amount of undesirable reaction products in the process, a problem that triggered surface modification of TiO₂ for enhanced photocatalytic performance. Previous studies focused on decreasing rate of charge carrier recombination and absorption of light in the visible region. Yet, increasing active sites and adsorption capacity by combining TiO₂ with a high surface area adsorbent such as activated carbon (AC) remains unexploited. This study reports the potential of such modification in simultaneous removal of nitrates and oxalic acid in aqueous environment. The adsorptive behaviour of nitrate and oxalic acid on TiO₂ and TiO₂/AC composites were studied. The Langmuir adsorption coefficient for nitrate was four times greater than that of oxalic acid. However, the amount of oxalic acid adsorbed was about 10 times greater than the amount of nitrate taken up. Despite this advantage, the materials did not appear to produce more active photocatalysts for the simultaneous degradation of nitrate and oxalic acid. The photocatalytic activity of TiO₂ and its carbon-based composites was improved by combination with Cu₂O particles. Consequently, 2.5 Cu₂O/TiO₂ exhibited the maximum photocatalytic performance with 57.6 and 99.8% removal of nitrate and oxalic acid, respectively, while selectivity stood at 45.7, 12.4 and 41.9% for NH₄⁺, NO₂^? and N₂, respectively. For the carbon based, 2.5 Cu₂O/TiO₂-20AC showed removal of 12.7% nitrate and 80.3% oxalic acid and achieved 21.6, 0 and 78.4% selectivity for NH₄⁺, NO₂^? and N₂, respectively. Using the optimal AC loading (20 wt%) resulted in significant decrease in the selectivity for NH₄⁺ with no formation of NO₂^?, which unveils that selectivity for N₂ and low/no selectivity for undesirable products can be manipulated by controlling the rate of consumption of oxalic acid. In contract, no nitrate reduction was observed with Cu₂O promoted TiO₂-T and its TiO₂-(T)-20AC, which may be connected to amorphous nature of TiO₂-T and perhaps served as charge carrier trapping sites that impeded activity.     

Visible light photocatalytic antibacterial activity of Ni-doped and N-doped TiO<Subscript>2</Subscript> on <Emphasis Type="Italic">Staphylococcus aureus</Emphasis> and <Emphasis Type="Italic">Escherichia coli</Emphasis> bacteria

The Ni-doped and N-doped TiO₂ nanoparticles were investigated for their antibacterial activities on Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) bacteria. Their morphological features and characteristics such as particle size, surface area, and visible light absorbing capacity were compared and discussed. Scanning electron microscopy, X-ray diffraction, and UV–visible spectrophotometry were used to characterize both materials. The inactivation of E. coli (as an example of Gram-negative bacteria) and S. aureus (as an example of Gram-positive bacteria) with Ni-doped and N-doped TiO₂ was investigated in the absence and presence of visible light. Antibacterial activity tests were conducted using undoped, Ni-doped, and N-doped TiO₂. The N-doped TiO₂ nanoparticles show higher antibacterial activity than Ni-doped TiO₂. The band gap narrowing of N-doped TiO₂ can induce more visible light absorption and leads to the superb antibacterial properties of this material. The complete inactivation time for E. coli at an initial cell concentration of 2.7?×?10⁴ CFU/mL was 420 min which is longer than the 360 min required for S. aureus inactivation. The rate of inactivation of S. aureus using the doped TiO₂ nanoparticles in the presence of visible light is greater than that of E. coli. The median lethal dose (LD50) values of S. aureus and E. coli by antibacterial activity under an 18-W visible light intensity were 80 and 350 mg/ml for N-doped TiO₂, respectively.     

Synthesis of Fe-doped Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocatalyst and its sonophotocatalytic activity on synthetic dye and real textile wastewater

The catalysts such as Fe, Bi₂O₃, and Fe-doped Bi₂O₃ were synthesized for the sonophotocatalytic treatment of synthetic dye and real textile wastewater. The resultant catalysts were characterized for its size and uniform shape using x-ray diffractogram (XRD) and scanning electron microscopy (SEM) which signified the nanorod shape formed Bi₂O₃. The higher ultraviolet light absorbance capacity of the catalysts was also evident using diffuse reflectance spectroscopy (DRS). Initially, the effect of conventional parameters such as initial pH, gas bubbling (argon, oxygen, air and nitrogen) and oxidant addition (H₂O₂ and peroxymonosulfate) in the presence of sonolysis (22 and 37 kHz frequency) and photolysis (UV-C light) on 10 ppm Basic Brown 1 dye was studied. The results showed that highest decolorization of 62 % was attained for 3 g/L peroxymonosulfate under 37 kHz frequency sonolysis treatment. Secondly, with the catalyst study, highest of 46 % dye color removal was obtained with 4 g/L Fe under 37 kHz frequency sonolysis treatment. The sonophotocatalytic treatment of dye with Fe-doped Bi₂O₃ catalyst in combination with peroxymonosulfate showed highest color removal of 99 %. Finally, the sonophotocatalytic treatment of real textile wastewater in the presence of 3 g/L Fe-doped Bi₂O₃ and 6 g/L peroxymonosulfate reduced the total organic carbon (TOC) and chemical oxygen demand (COD) level to 77 and 91 %, respectively, in 180 min. The reported treatment process was found to treat the synthetic dye and real textile wastewater effectively.     

Effects of land use conversion and fertilization on CH<Subscript>4</Subscript> and N<Subscript>2</Subscript>O fluxes from typical hilly red soil

Land use conversion and fertilization have been widely reported to be important managements affecting the exchanges of greenhouse gases between soil and atmosphere. For comprehensive assessment of methane (CH₄) and nitrous oxide (N₂O) fluxes from hilly red soil induced by land use conversion and fertilization, a 14-month continuous field measurement was conducted on the newly converted citrus orchard plots with fertilization (OF) and without fertilization (ONF) and the conventional paddy plots with fertilization (PF) and without fertilization (PNF). Our results showed that land use conversion from paddy to orchard reduced the CH₄ fluxes at the expense of increasing the N₂O fluxes. Furthermore, fertilization significantly decreased the CH₄ fluxes from paddy soils in the second stage after conversion, but it failed to affect the CH₄ fluxes from orchard soils, whereas fertilizer applied to orchard and paddy increased soil N₂O emissions by 68 and 113.9 %, respectively. Thus, cumulative CH₄ emissions from the OF were 100 % lower, and N₂O emissions were 421 % higher than those from the PF. Although cumulative N₂O emissions were stimulated in the newly converted orchard, the strong reduction of CH₄ led to lower global warming potentials (GWPs) as compared to the paddy. Besides, fertilization in orchard increased GWPs but decreased GWPs of paddy soils. In addition, measurement of soil moisture, temperature, dissolved carbon contents (DOCs), and ammonia (NH₄ ⁺-N) and nitrate (NO₃ ^?-N) contents indicated a significant variation in soil properties and contributed to variations in soil CH₄ and N₂O fluxes. Results of this study suggest that land use conversion from paddy to orchard would benefit for reconciling greenhouse gas mitigation and citrus orchard cultivation would be a better agricultural system in the hilly red soils in terms of greenhouse gas emission. Moreover, selected fertilizer rate applied to paddy would lead to lower GWPs of CH₄ and N₂O. Nevertheless, more field measurements from newly converted orchard are highly needed to gain an insight into national and global accounting of CH₄ and N₂O emissions.     

Hydrogen production using thermocatalytic decomposition of methane on Ni<Subscript>30</Subscript>/activated carbon and Ni<Subscript>30</Subscript>/carbon black

Hydrogen is an energy carrier of the future need. It could be produced from different sources and used for power generation or as a transport fuel which mainly in association with fuel cells. The primary challenge for hydrogen production is reducing the cost of production technologies to make the resulting hydrogen cost competitive with conventional fuels. Thermocatalytic decomposition (TCD) of methane is one of the most advantageous processes, which will meet the future demand, hence an attractive route for CO_x free environment. The present study deals with the production of hydrogen with 30 wt% of Ni impregnated in commercially available activated carbon and carbon black catalysts (samples coded as Ni₃₀/AC and Ni₃₀/CB, respectively). These combined catalysts were not attempted by previous studies. Pure form of hydrogen is produced at 850 °C and volume hourly space velocity (VHSV) of 1.62 L/h g on the activity of both the catalysts. The analysis (X-ray diffraction (XRD)) of the catalysts reveals moderately crystalline peaks of Ni, which might be responsible for the increase in catalytic life along with formation of carbon fibers. The activity of carbon black is sustainable for a longer time compared to that of activated carbon which has been confirmed by life time studies (850 °C and 54 sccm of methane).     

Potassium-based sorbents from fly ash for high-temperature CO<Subscript>2</Subscript> capture

Potassium-fly ash (K-FA) sorbents were investigated for high-temperature CO₂ sorption. K-FAs were synthesised using coal fly ash as source of silica and aluminium. The synthesised materials were also mixed with Li₂CO₃ and Ca(OH)₂ to evaluate their effect on CO₂ capture. Temperature strongly affected the performance of the K-FA sorbents, resulting in a CO₂ uptake of 1.45 mmol CO₂/g sorbent for K-FA 1:1 at 700 °C. The CO₂ sorption was enhanced by the presence of Li₂CO₃ (10 wt%), with the K-FA 1:1 capturing 2.38 mmol CO₂/g sorbent at 700 °C in 5 min. This sorption was found to be similar to previously developed Li-Na-FA (2.54 mmol/g) and Li-FA (2.4 mmol/g) sorbents. The presence of 10 % Li₂CO₃ also accelerated sorption and desorption. The results suggest that the increased uptake of CO₂ and faster reaction rates in presence of K-FA can be ascribed to the formation of K-Li eutectic phase, which favours the diffusion of potassium and CO₂ in the material matrix. The cyclic experiments showed that the K-FA materials maintained stable CO₂ uptake and reaction rates over 10 cycles.     

First assessment of the PM<Subscript>10</Subscript> and PM<Subscript>2.5</Subscript> particulate level in the ambient air of belgrade city

INTENTION, GOAL, SCOPE, BACKGROUND: As the strong negative health effect of exposure to the inhalable particulate matter PM10 in the urban environment has been confirmed, the study of the mass concentrations, physico-chemical characteristics, sources, as well as spatial and temporal variation of atmospheric aerosol particles becomes very important. OBJECTIVE: This work is a pilot study to assess the concentration level of ambient suspended particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade central urban area. Average daily concentrations of PM10 and PM2.5 have been measured at three representative points in the city between June 2002 and December 2002. The influence of meteorological parameters on PM10 and PM2.5 concentrations was analyzed, and possible pollution sources were identified. METHODS: Suspended particles were collected on Pure Teflon filters by using a Mini-Vol low-volume air sampler (Airmetrics Co., Inc.; 5 l min(-1) flow rate). Particle mass was determined gravimetrically after 48 h of conditioning in a desiccator, in a Class 100 clean room at the temperature T = 20 degrees C and at about 50% constant relative humidity (RH). RESULTS AND DISCUSSION: Analysis of the PM10 data indicated a marked difference between season without heating--(summer; mean value 56 microg m(-3)) and heating season--(winter; mean value 96 microg m3); 62% of samples exceeded the level of 50 microg m(-3). The impact of meteorological factors on PM concentrations was not immediately apparent, but there was a significant negative correlation with the wind speed. CONCLUSIONS: The PM10 and PM2.5 mass concentrations in the Belgrade urban area had high average values (77 microg m(-3) and 61 microg m(-3)) in comparison with other European cities. The main sources of particulate matter were traffic emission, road dust resuspension, and individual heating emissions. When the air masses are coming from the SW direction, the contribution from the Obrenovac power plants is evident. During days of exceptionally severe pollution, in both summer and winter periods, high production of secondary aerosols occurred, as can be seen from an increase in PM2.5 in respect to PM10 mass concentration. RECOMMENDATION AND OUTLOOK: The results obtained gave us the first impression of the concentration level of particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade ambient air. Due to measured high PM mass concentrations, it is obvious that it would be very difficult to meet the EU standards (EEC 1999) by 2010. It is necessary to continue with PM10 and PM2.5 sampling; and after comprehensive analysis which includes the results of chemical and physical characterization of particles, we will be able to recommend effective control measures in order to improve air quality in Belgrade.     

Response of anaerobic membrane bioreactor to the presence of nano-Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript>: reactor performance,supernatant characteristics,and microbial community

Considering the increasing incorporation of manufactured nano-material into consumer products, there is a concern about its potential impacts in biological wastewater treatment. In this study, the response of anaerobic sludge to the presence of Bi₂WO₆ nano-particles (NPs) was investigated in the anaerobic membrane bioreactor (AnMBR). As the concentration of Bi₂WO₆ in the reactor was controlled around 1 mg/L, there was no significant difference in effluent water quality or bacterial activities before and after NP exposure, partially due to the microbial-induced NP aggregation and stable complex formation. However, with the increasing dosage of Bi₂WO₆ from 5 to 40 mg/L, great influences on the AnMBR performance were observed, including the reduction of COD removal efficiency, inhibition of the mechanization step, increased production of soluble microbial products, and enhanced secretion of extracellular polymer substrates. Additional investigation with high-throughput sequencing was conducted, clearly demonstrating that Bi₂WO₆ NPs induced changes in the bacterial community.