Response surface optimization of a dynamic dye adsorption process: a case study of crystal violet adsorption onto NaOH-modified rice husk

The adsorption of crystal violet from aqueous solution by NaOH-modified rice husk was investigated in a laboratory-scale fixed-bed column. A two-level three factor (2³) full factorial central composite design with the help of Design Expert Version 7.1.6 (Stat Ease, USA) was used for optimisation of the dynamic dye adsorption process and evaluation of interaction effects of different operating parameters: initial dye concentration (100–200 mg L^?1), flow rate (10–30 mL min^?1) and bed height (5–25 cm). A correlation coefficient (R ²) value of 0.999, model F value of 1,936.59 and its low p value (<0.0001) along with lower value of coefficient of variation (1.38 %) indicated the fitness of the response surface quadratic model developed during the present study. Numerical optimisation applying desirability function was used to identify the optimum conditions for a targeted breakthrough time of 12 h. The optimum conditions were found to be initial solution pH?=?8.00, initial dye concentration?=?100 mg L^?1, flow rate?=?22.88 mL min^?1 and bed height?=?18.75 cm. A confirmatory experiment was performed to evaluate the accuracy of the optimised procedure. Under the optimised conditions, breakthrough appeared after 12.2 h and the column efficiency was determined as 99 %. The Thomas model showed excellent fit to the dynamic dye adsorption data obtained from the confirmatory experiment. Thereby, it was concluded that the current investigation gives valuable insights for designing and establishing a continuous wastewater treatment plant.     

In situ photoelectrochemical/photocatalytic study of a dye discoloration in a microreactor system using TiO2 thin films

Introduction

In this work, we report in situ studies of UV photoelectrocatalytic discoloration of a dye (indigo carmine) by a TiO₂ thin film in a microreactor to demonstrate the driving force of the applied electrode potential and the dye flow rate toward dye discoloration kinetics.

Methods

TiO₂ 65-nm-thick thin films were deposited by PVD magnetron sputtering technique on a conducting glass substrate of fluorinated tin oxide. A microreactor to measure the discoloration rate, the electrode potential, and the photocurrent in situ, was developed. The dye solutions, before and after measurements in the microreactor, were analyzed by Raman spectroscopy.

Results

The annealed TiO₂ thin films had anatase structure with preferential orientation (101). The discoloration rate of the dye increased with the applied potential to TiO₂ electrode. Further, acceleration of the photocatalytic reaction was achieved by utilizing dye flow recirculation to the microreactor. In both cases the photoelectrochemical/photocatalytic discoloration kinetics of the dye follows the Langmuir?CHinshelwood model, with first-order kinetics.

Conclusions

The feasibility of dye discoloration on TiO₂ thin film electrodes, prepared by magnetron sputtering using a flow microreactor system, has been clearly demonstrated. The discoloration rate is enhanced by applying a positive potential (E _AP) and/or increasing the flow rate. The fastest discoloration and shortest irradiation time (50?min) produced 80% discoloration with an external anodic potential of 0.931?V and a flow rate of 12.2?mL?min^?1.     

高压电弧放电处理偶氮染料废水

用高压电弧放电产生的低温等离子体对含偶氮染料的废水进行了处理,以甲基橙为例研究了电压幅值、处理时间、溶液初始浓度、溶液初始pH值、投加Fe^2＋和Fe^3＋对染料脱色的影响。实验结果表明,甲基橙浓度为50mg／L时其降解率随时间和电压幅值的增加而增加。溶液初始浓度对染料去除效果影响较为明显,同等条件下初始浓度越低降解率越高。酸性条件下有利于低温等离子体处理甲基橙。Fe^2＋和Fe^3＋对低温等离子体降解甲基橙有一定的催化作用。电压8kV处理3min,Fe^2＋为20mg／L时去除率由89．64％增至99．72％。Fe2（SO4）,的最佳投加量为5mg／L（以Fe^3＋计）,而FeCl,的最佳投加量为80mg／L（以Fe^3＋计）。     

Predictive modeling of sorption and desorption of a reactive azo dye by pumpkin husk

The use of effective disposal of redundant pumpkin husk (PH) to remove pollutants is an important issue for environmental protection and utilization of resource. The aim of this study was to remove a potentially toxic reactive azo dye, Reactive Red (RR) 120, by widespread PH as a low-cost adsorbent. Particle size, adsorbent dose, pH, temperature, initial dye concentration, and contact time affected the sorption process. Amine, amide, hydroxyl, and carboxyl groups of PH played significant roles on the sorption process. Rapid sorption occurred within the first 2 min and equilibrium was reached within 60 min. Sorption kinetic was well represented by logistic equation. Generated secondary logistic model can be used to describe effects of initial dye concentration, contact time, and temperature by a single equation with high R ² value. Monolayer sorption capacity was found as 98.61 mg g^-1. Activation energy, thermodynamic, and desorption studies showed that this process was physical, endothermic, and spontaneous. This study indicated that redundant PH as a low-cost adsorbent had a great potential for the removal of RR 120 as an alternative eco-friendly process.     

Sorption and desorption studies of a reactive azo dye on effective disposal of redundant material

The effective disposal of redundant elephant dung (ED) is important for environmental protection and utilization of resource. The aim of this study was to remove a toxic-azo dye, Reactive Red (RR) 120, using this relatively cheap material as a new adsorbent. The FTIR–ATR spectra of ED powders before and after the sorption of RR 120 and zero point charge (pH_zpc) of ED were determined. The sorption capacity of ED for removing of RR 120 were carried out as functions of particle size, adsorbent dose, pH, temperature, ionic strength, initial dye concentration, and contact time. Sorption isotherm, kinetic, activation energy, thermodynamic, and desorption parameters of RR 120 on ED were studied. The sorption process was found to be dependent on particle size, adsorbent dose, pH, temperature, ionic strength, initial dye concentration, and contact time. FTIR–ATR spectroscopy indicated that amine and amide groups have significant role on the sorption of RR 120 on ED. The pH_zpc of ED was found to be 7.3. Sorption kinetic of RR 120 on ED was well described by sigmoidal Logistic model. The Langmuir isotherm was well fitted to the equilibrium data. The maximum sorption capacity was 95.71 mg?g^?1. The sorption of RR 120 on ED was mainly physical and exothermic according to results of D–R isotherm, Arrhenius equation, thermodynamic, and desorption studies. The thermodynamic parameters showed that this process was feasible and spontaneous. This study showed that ED as a low-cost adsorbent had a great potential for the removal of RR 120 as an alternative eco-friendly process.     

Color removal from wastewater using a synthetic high-performance antifouling GO-CPTMS@Pd-TKHPP/polyether sulfone nanofiltration membrane

Modified graphene oxide with 5,10,15,20-tetrakis-(4-hexyloxyphenyl)-porphyrin and palladium (II) (signified by GO-CPTMS@Pd-TKHPP) prepared as a novel antifouling polyether sulfone (PES) blended nanofiller membrane. The membrane efficiency has been analyzed such as pure water flux (PWF), hydrophilicity, and antifouling features. By increasing of modified graphene oxide percentage from 0 to 0.1 wt.% in the polymer matrix, the PWF was incremented from 14.35 to 37.33 kg/m²·h at 4 bar. The membrane flux recovery ratio (FRR) has been investigated by applying powdered milk solution; the FRR results indicated that the 0.1 wt.%-modified graphene oxide membrane showed a positive effect on fouling behavior with Rir and FRR value 8.24% and 91.76%, respectively. The nanofiltration membrane performance was assessed applying the Direct Red 16 dye rejection. It was demonstrated that the optimal membranes (0.1 wt.%-modified graphene oxide) had notable dye removal (99.58% rejection). The results are also verified by measuring the scanning electron microscopy (SEM), water contact angle (WCA), and atomic microscopy analysis (AFM).

     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

铈离子光催化降解茜素绿的性能和机理简

主要研究了简单铈离子（Ce³⁺）在紫外光（UV）的作用下对蒽醌染料茜素绿（AG）的光催化降解效果和反应机理。结果表明,UV/Ce³⁺体系能够有效降解AG,初始反应速率随AG浓度的倒数值和Ce³⁺浓度的增加而线性增加,随初始溶液pH的增加先降低后增加,在酸性条件下有很高的TOC去除率。荧光探针实验表明,反应过程中可以产生·OH自由基。UV/Ce³⁺体系对其他类型染料和对硝基苯酚都有较好的降解效果。     

Electrosorption and photocatalytic one-stage combined process using a new type of nanosized TiO2/activated charcoal plate electrode

In the present study, an activated charcoal (AC) plate was prepared by physical activation method. Its surface was coated with TiO₂ nanoparticles by electrophoretic deposition (EPD) method. The average crystallite size of TiO₂ nanoparticles was determined approximately 28 nm. The nature of prepared electrode was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer–Emmett–Teller (BET) surface area measurement before and after immobilization. The electrosorption and photocatalytic one-stage combined process was investigated in degradation of Lanasol Red 5B (LR5B), and the effect of dye concentration, electrolyte concentration, pH, voltage, and contact time was optimized and modeled using response surface methodology (RSM) approach. The dye concentration of 30 mg L^?1, Na₂SO₄ concentration of 4.38 g L^?1, pH of 4, voltage of 250 mV, and contact time of 120 min were determined as optimum conditions. Decolorization efficiency increased in combined process to 85.65 % at optimum conditions compared to 66.03 % in TiO₂/AC photocatalytic, 20.09 % in TiO₂/AC electrosorption, and 1.91 % in AC photocatalytic processes.     

Exposure assessment of operators to pesticides in Kongou,a sub-watershed of Niger River valley

The use of pesticides in horticultural sector in Niger has become an integral part of modern agriculture. Nevertheless, their inappropriate use can generate negative health effects to operators. A study was carried out among Kongou farmers in order to assess their potential dermal exposure (PDE). The UK-POEM model was used to quantify the PDE during mixing/loading and application according to the local practices. In order to determine which parts of the operator body are subject to most contamination during spraying and to validate the theoretical model used, a patch method was used with a tartrazine dye. The deposits of the tartrazine on patches were measured by colorimetry thanks to the absorbance value determined after their extraction in water and a calibration curve. A total of ten spraying trials (five trials with the hand-held sprayer and five others with the backpack sprayer) were performed by different producers at 0.5 and 1 m height for each trial. The survey shows that 92% of the farmers are illiterate and the most common active substances identified are organophosphate or pyrethroids insecticides. Seventy percent of operators do not use any personal protective equipment (PPE) during mixing/loading or spraying. The predictive systemic exposure levels vary from 0.0027?mg kg^?1 bw per day to 0.7692?mg kg^?1 bw per day for backpack sprayer and from 0.0261?mg kg^?1 bw per day to 0.9788?mg kg^?1 bw per day for hand-held sprayer, several times higher the Acceptable Operator Exposure Level (AOEL) for some actives substances. Theoretical modeling indicates more exposure of operator by a hand-held sprayer than a backpack sprayer. The patch method results show that the deposits of dye increase when the position of sprayer nozzle increases from 0.5 to 1 m for the two sprayers. All parts of the operator body are contaminated but lower body parts and chest are the most exposed. The patch method results also show that hand spraying contaminates operator more than backpack spraying, confirming the results of the theoretical model.     

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g^?1at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.     

An investigation of anthraquinone dye biodegradation by immobilized Aspergillus flavus in fluidized bed bioreactor

Purpose

Biodegradation and biodecolorization of Drimarene blue K₂RL (anthraquinone) dye by a fungal isolate Aspergillus flavus SA2 was studied in lab-scale immobilized fluidized bed bioreactor (FBR) system.

Method

Fungus was immobilized on 0.2-mm sand particles. The reactor operation was carried out at room temperature and pH?5.0 in continuous flow mode with increasing concentrations (50, 100, 150, 200, 300, 500?mg?l^?1) of dye in simulated textile effluent on the 1st, 2nd, 5th, 8th, 11th, and 14th days. The reactors were run on fill, react, settle, and draw mode, with hydraulic retention time (HRT) of 24?C72?h. Total run time for reactor operation was 17?days.

Results

The average overall biological oxygen demand (BOD), chemical oxygen demand (COD), and color removal in the FBR system were up to 85.57%, 84.70%, and 71.3%, respectively, with 50-mg?l^?1 initial dye concentration and HRT of 24?h. Reductions in BOD and COD levels along with color removal proved that the mechanism of biodecolorization and biodegradation occurred simultaneously. HPLC and LC?CMS analysis identified phthalic acid, benzoic acid, 1, 4-dihydroxyanthraquinone, 2,3-dihydro-9,10-dihydroxy-1,4-anthracenedione, and catechol as degradation products of Drimarene blue K₂RL dye. Phytotoxicity analysis of bioreactor treatments provided evidence for the production of less toxic metabolites in comparison to the parent dye.

Conclusion

The present fluidized bed bioreactor setup with indigenously isolated fungal strain in its immobilized form is efficiently able to convert the parent toxic dye into less toxic by-products.     

Biosorption of synthetic dyes (Direct Red 89 and Reactive Green 12) as an ecological refining step in textile effluent treatment

With the use of cost-effective natural materials, biosorption is considered as an ecological tool that is applied worldwide for the remediation of pollution. In this study, we proposed Lemna gibba biomass (LGB), a lignocellulosic sorbent material, for the removal of two textile dyes, Direct Red 89 (DR-89) and Reactive Green 12 (RG-12). These azo dyes commonly used in dying operations of natural and synthetic fibres are the most important pollutants produced in textile industry effluents. For this purpose, batch biosorption experiments were carried out to assess the efficacy of LGB on dye treatment by evaluating the effect of contact time, biomass dosage, and initial dye concentration. The results indicated that the bioremoval efficiency of 5 mg?L^?1 DR-89 and RG-12 reached approximately 100 % after 20 min of the exposure time; however, the maximum biosorption of 50 mg?L^?1 DR-89 and 15 mg?L^?1 RG-12 was determined to be about 60 and 47 %, respectively. Fourier transform infrared spectroscopy used to explain the sorption mechanism showed that the functional groups of carboxylic acid and hydroxyl played a major role in the retention of these pollutants on the biomass surface. The modelling results using Freundlich, Langmuir, Temkin, Elovich, and Dubini Radushkevich (D-R) isotherms demonstrated that the DR-89 biosorption process was better described with the Langmuir theory (R ²?=?0.992) while the RG-12 biosorption process fitted well by the D-R isotherm equation (R ²?=?0.988). The maximum biosorption capacity was found to be 20.0 and 115.5 mg?g^?1 for DR-89 and RG-12, respectively, showing a higher ability of duckweed biomass for the bioremoval of the green dye. The thermodynamic study showed that the dye biosorption was a spontaneous and endothermic process. The efficacy of using duckweed biomass for the bioremoval of the two dyes was limited to concentrations ≤50 mg?L^?1, indicating that L. gibba biomass may be suitable in the refining step of textile effluent treatment.     

Artificial neural network (ANN) modeling of adsorption of methylene blue by NaOH-modified rice husk in a fixed-bed column system

In this study, rice husk was modified with NaOH and used as adsorbent for dynamic adsorption of methylene blue (MB) from aqueous solutions. Continuous removal of MB from aqueous solutions was studied in a laboratory scale fixed-bed column packed with NaOH-modified rice husk (NMRH). Effect of different flow rates and bed heights on the column breakthrough performance was investigated. In order to determine the most suitable model for describing the adsorption kinetics of MB in the fixed-bed column system, the bed depth service time (BDST) model as well as the Thomas model was fitted to the experimental data. An artificial neural network (ANN)-based model was also developed for describing the dynamic dye adsorption process. An extensive error analysis was carried out between experimental data and data predicted by the models by using the following error functions: correlation coefficient (R ²), average relative error, sum of the absolute error and Chi-square statistic test (χ ²). Results show that with increasing bed height and decreasing flow rate, the breakthrough time was delayed. All the error functions yielded minimum values for the ANN model than the traditional models (BDST and Thomas), suggesting that the ANN model is the most suitable model to describe the fixed-bed adsorption of MB by NMRH. It is also more rational and reliable to interpret dynamic dye adsorption data through a process of ANN architecture.     

Electro-oxidation of the dye azure B: kinetics,mechanism, and by-products

In this work, the electrochemical degradation of the dye azure B in aqueous solutions was studied by electrochemical advanced oxidation processes (EAOPs), electro-Fenton, and anodic oxidation processes, using Pt/carbon-felt and boron-doped diamond (BDD)/carbon-felt cells with H₂O₂ electrogeneration. The higher oxidation power of the electro-Fenton (EF) process using BDD anode was demonstrated. The oxidative degradation of azure B by the electrochemically generated hydroxyl radicals (^?OH) follows a pseudo-first-order kinetics. The apparent rate constants of the oxidation of azure B by ^?OH were measured according to pseudo-first-order kinetic model. The absolute rate constant of azure B hydroxylation reaction was determined by competition kinetics method and found to be 1.19?×?10⁹ M^?1 s^?1. It was found that the electrochemical degradation of the dye leads to the formation of aromatic by-products which are then oxidized to aliphatic carboxylic acids before their almost mineralization to CO₂ and inorganic ions (sulfate, nitrate, and ammonium). The evolution of the TOC removal and time course of short-chain carboxylic acids during treatment were also investigated.     

Removal of Disperse Red dye by bamboo-based activated carbon: optimisation, kinetics and equilibrium

This research involved the use of response surface methodology (RSM) to investigate the adsorption of Disperse Red 167 dye onto the bamboo-based activated carbon activated with H₃PO₄ (PBAC) in a batch process. F400, a commercially available activated carbon, was used in parallel for comparison. Analysis of variance showed that input variables such as the contact time, temperature, adsorbent dosage and the interaction between the temperature and the contact time had a significant effect on the dye removal for both adsorbents. RSM results show that the optimal contact time, temperature, initial dye concentration and adsorbent dosage for both adsorbents were found to be 15.4 h, 50 °C, 50.0 mg L^?1 and 12.0 g L^?1, respectively. Under these optimal conditions, the removal efficiencies reached 90.23 % and 92.13 % for PBAC and F400, respectively, with a desirability of 0.937. The validation of the experimental results confirmed the prediction of the models derived from RSM. The adsorption followed a nonlinear pseudo-first-order model and agreed well with the Freundlich and Temkin isotherm as judged by the levels of the AICc and the Akaike weight. Furthermore, the thermodynamics analysis indicated that, for both adsorbents, the adsorption was a physical process that was spontaneous, entropy-increasing and endothermic.     

Formation of shaped barium sulfate-dye hybrids: waste dye utilization for eco-friendly treatment of wastewater

Purpose

Owing to the present complexity and difficulty of concentrated dye wastewater treatment, this work aimed to synthesize a reproducible waste-sorbing material for the treatment of wastewater by forming the dye-conjugating complex hybrid.

Methods

The inorganic/organic hybridization was applied to prepare the objective material by immobilizing waster dye-Mordant blue 9 (MB) with barium sulfate (BaSO₄). The composition and pattern of the formed material were determined by spectrometry and characterized by SEM and XRD, and their formation process was clarified. The adsorption of cationic dye-basic blue BO (BB) and copper ion was investigated..

Results

The hybrid of MB alone into growing BaSO₄ formed the pineapple-like particles while that of the MB/BB-conjugating complex was the rhombus material. The adsorption of BB on the MB–BaSO₄ hybrid was probably attributed to ion-pair equilibrium and that of Cu²⁺ may result from the complexation. The treatment of dye and heavy metal wastewaters indicated that the MB hybrid material removed 99.8% BB and 97% Cu²⁺ and the dye-conjugating hybrid with growing BaSO₄ 100% MB, 99.5% BB, and 44% Cu²⁺.

Conclusion

The waste MB–BaSO₄ hybrid material is efficient to treat cationic dye and Cu²⁺ wastewater. The dye-conjugating hybridization method is the first to be advanced for in situ wastewater treatment, and it showed a combined effect for the removal of both organic dyes and heavy metals.     

Low-cost adsorbents from bio-waste for the removal of dyes from aqueous solution

Activated carbons (ACs) were developed from bio-waste materials like rice husk and peanut shell (PS) by various physicochemical activation methods. PS char digested in nitric acid followed by treatment at 673 K resulted in high surface area up to ～585 m²/g. The novelty of the present study is the identification of oxygen functional groups formed on the surface of activated carbons by infrared and X-ray photoelectron spectroscopy and quantification by using temperature programmed decomposition (TPD). Typical TPD data indicated that each activation method may lead to varying amounts of acidic and basic functional groups on the surface of the adsorbent, which may be a crucial factor in determining the adsorption capacity. It was shown that ACs developed during the present study are good adsorbents, especially for the removal of a model textile dye methylene blue (MB) from aqueous solution. As MB is a basic dye, H₂O₂-treated rice husk showed the best adsorption capacity, which is in agreement with the acidic groups present on the surface. Removal of the dye followed Langmuir isotherm model, whereas MB adsorption on ACs followed pseudo-second-order kinetics.     

Biodegradation of methyl red by Bacillus sp. strain UN2: decolorization capacity,metabolites characterization,and enzyme analysis

Azo dyes are recalcitrant and refractory pollutants that constitute a significant menace to the environment. The present study is focused on exploring the capability of Bacillus sp. strain UN2 for application in methyl red (MR) degradation. Effects of physicochemical parameters (pH of medium, temperature, initial concentration of dye, and composition of the medium) were studied in detail. The suitable pH and temperature range for MR degradation by strain UN2 were respectively 7.0–9.0 and 30–40 °C, and the optimal pH value and temperature were respectively 8.0 and 35 °C. Mg²⁺ and Mn²⁺ (1 mM) were found to significantly accelerate the MR removal rate, while the enhancement by either Fe³⁺ or Fe²⁺ was slight. Under the optimal degradation conditions, strain UN2 exhibited greater than 98 % degradation of the toxic azo dye MR (100 ppm) within 30 min. Analysis of samples from decolorized culture flasks confirmed biodegradation of MR into two prime metabolites: N,N′dimethyl-p-phenyle-nediamine and 2-aminobenzoic acid. A study of the enzymes responsible for the biodegradation of MR, in the control and cells obtained during (10 min) and after (30 min) degradation, showed a significant increase in the activities of azoreductase, laccase, and NADH-DCIP reductase. Furthermore, a phytotoxicity analysis demonstrated that the germination inhibition was almost eliminated for both the plants Triticum aestivum and Sorghum bicolor by MR metabolites at 100 mg/L concentration, yet the germination inhibition of parent dye was significant. Consequently, the high efficiency of MR degradation enables this strain to be a potential candidate for bioremediation of wastewater containing MR.