Removal of Cu, Zn, and Cd from aqueous solutions by the dairy manure-derived biochar

Purpose

Biochar derived from waste biomass is now gaining much attention for its function as a biosorbent for environmental remediation. The objective of this study was to determine the effectiveness of biochar as a sorbent in removing Cd, Cu, and Zn from aqueous solutions.

Methods

Biochar was produced from dairy manure (DM) at two temperatures: 200°C and 350°C, referred to as DM200 and DM350, respectively. The obtained biochars were then equilibrated with 0–5 mM Cu, Zn or Cd in 0.01 M NaNO₃ solution for 10 h. The changes in solution metal concentrations after sorption were evaluated for sorption capacity using isotherm modeling and chemical speciation Visual MINTEQ modeling, while the solid was collected for species characterization using infrared spectroscopy and X-ray elemental dot mapping techniques.

Results

The isotherms of Cu, Zn, and Cd sorption by DM200 were better fitted to Langmuir model, whereas Freundlich model well described the sorption of the three metals by DM350. The DM350 were more effective in sorbing all three metals than DM200 with both biochars had the highest affinity for Cu, followed by Zn and Cd. The maximum sorption capacities of Cu, Zn, and Cd by DM200 were 48.4, 31.6, and 31.9 mg g^?1, respectively, and those of Cu, Zn, and Cd by DM350 were 54.4, 32.8, and 51.4 mg g^?1, respectively. Sorption of the metals by the biochar was mainly attributed to their precipitation with PO ₄ ^3? or CO ₃ ^2? originating in biochar, with less to the surface complexation through –OH groups or delocalized π electrons. At the initial metal concentration of 5 mM, 80–100 % of Cu, Zn, and Cd retention by DM200 resulted from the precipitation, with less than 20 % from surface adsorption through phenonic –OH complexation. Among the precipitation, 20–30 % of the precipitation occurred as metal phosphate and 70–80 % as metal carbonate. For DM350, 75–100 % of Cu, Zn, and Cd retention were due to the precipitation, with less than 25 % to surface adsorption through complexation of heavy metal by phenonic –OH site or delocalized π electrons. Among the precipitation, only less than 10 % of the precipitation was present as metal phosphate and more than 90 % as metal carbonate.

Conclusions

Results indicated that dairy manure waste can be converted into value-added biochar as a sorbent for sorption of heavy metals, and the mineral components originated in the biochar play an important role in the biochar's high sorption capacity.     

Development of a country-specific CO2 emission factor for domestic anthracite in Korea, 2007�C2009

Introduction

Korea has been making efforts to reduce greenhouse gas (GHG) emissions, including a voluntary commitment to the target of a 30% reduction, based on business-as-usual of the total GHG emission volume, by 2020; 2006 IPCC Guidelines provided default values, applying country-specific emission factors was recommended when estimating national greenhouse gas emissions.

Results and discussion

This study focused on anthracite produced in Korea in order to provide basic data for developing country-specific emission factor. This study has estimated CO₂ emission factors to use worksheet of which five steps consisted according to the fuel analysis method.

Conclusion

As a result, the average of net colorific value for 3 years (2007??2009) was 4,519 kcal/kg, and the CO₂ emission factor was calculated to be 111,446 kg/TJ, which is about 11.8% lower than the 2006 IPCC guidelines default value, and about 7.9% higher than the US EPA emission factor.     

Characterization of PM10 atmospheric aerosol at urban and urban background sites in Fuzhou city, China

Background

PM₁₀ aerosol samples were simultaneously collected at two urban and one urban background sites in Fuzhou city during two sampling campaigns in summer and winter. PM₁₀ mass concentrations and chemical compositions were determined.

Methods

Water-soluble inorganic ions (Cl^?, NO ₃ ^? , SO ₄ ^2? , NH ₄ ⁺ , K⁺, Na⁺, Ca²⁺, and Mg²⁺), carbonaceous species (elemental carbon and organic carbon), and elements (Al, Si, Mg, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, and Pb) were detected using ion chromatography, thermal/optical reflectance, and proton-induced X-ray emission methods, respectively.

Results

PM₁₀ mass concentrations, as well as most of the chemical components, were significantly increased from urban background to urban sites, which were due to enhanced anthropogenic activities in urban areas. Elements, carbonaceous species, and most of the ions were more uniformly distributed at different types of sites in winter, whereas secondary ion SO ₄ ^2? , NO ₃ ^? , and NH ₄ ⁺ showed more evident urban-background contrast in this season. The chemical mass closure indicated that mineral dust, organic matters, and sulfate were the most abundant components in PM₁₀. The sum of individually measured components accounted for 86.9?C97.7% of the total measured PM₁₀ concentration, and the discrepancy was larger in urban area than in urban background area.

Conclusion

According to the principal component analysis?Cmultivariate linear regression model, mineral dust, secondary inorganic ions, sea salt, and motor vehicle were mainly responsible for the PM₁₀ particles in Fuzhou atmosphere, and contributed 19.9%, 53.3%, 21.3%, and 5.5% of PM₁₀, respectively.     

Temporal variations of atmospheric aerosol in four European urban areas

Purpose

The concentrations of PM₁₀ mass, PM_2.5 mass and particle number were continuously measured for 18 months in urban background locations across Europe to determine the spatial and temporal variability of particulate matter.

Methods

Daily PM₁₀ and PM_2.5 samples were continuously collected from October 2002 to April 2004 in background areas in Helsinki, Athens, Amsterdam and Birmingham. Particle mass was determined using analytical microbalances with precision of 1 ??g. Pre- and post-reflectance measurements were taken using smoke-stain reflectometers. One-minute measurements of particle number were obtained using condensation particle counters.

Results

The 18-month mean PM₁₀ and PM_2.5 mass concentrations ranged from 15.4 ??g/m³ in Helsinki to 56.7 ??g/m³ in Athens and from 9.0 ??g/m³ in Helsinki to 25.0 ??g/m³ in Athens, respectively. Particle number concentrations ranged from 10,091 part/cm³ in Helsinki to 24,180 part/cm³ in Athens with highest levels being measured in winter. Fine particles accounted for more than 60% of PM₁₀ with the exception of Athens where PM_2.5 comprised 43% of PM₁₀. Higher PM mass and number concentrations were measured in winter as compared to summer in all urban areas at a significance level p?Conclusions Significant quantitative and qualitative differences for particle mass across the four urban areas in Europe were observed. These were due to strong local and regional characteristics of particulate pollution sources which contribute to the heterogeneity of health responses. In addition, these findings also bear on the ability of different countries to comply with existing directives and the effectiveness of mitigation policies.     

BOD biosensors for pulp and paper industry wastewater analysis

Introduction

Two semi-specific microbial biosensors were constructed for the analysis of biochemical oxygen demand (BOD) in high-cellulose-content pulp and paper industry wastewaters. The biosensors were based on living cells of Bacillus subtilis and Paenibacillus sp. immobilized in an agarose gel matrix. Semi-specific microorganisms were isolated from various samples (decaying sawdust and rabbit manure) and were chosen based on their ability to assimilate cellulose.

Materials &; methods

The biosensors were calibrated with the Organization for Economic Cooperation and Development synthetic wastewater, and measurements with different wastewaters were conducted.

Results

The response time of biosensors using the steady-state method was 20?C25 min, and the service life of immobilized microorganisms was 96 days. Detection limit was 5 mg/l of BOD₇ while linear ranges extended up to 55 and 50 mg/l of the BOD₇ for B. subtilis- and Paenibacillus sp.-based biosensors, respectively. Repeatability and reproducibility of both biosensors were within the limits set by APHA??less than 15.4%. In comparison, both biosensors overestimated the BOD₇ values in paper mill wastewaters and underestimated the BOD₇ in aspen pulp mill wastewater.

Conclusions

The semi-specific biosensors are suitable for the estimation of organic pollution derived from cellulose, while the detection of pollution derived from tannins and lignins was minor. Better results in terms of accuracy and repeatability were gained with Paenibacillus sp. biosensor.     

Personal monitoring of exposure to particulate matter with a high temporal resolution

Background

Continuous monitoring of air quality is implemented by government institutions at fixed ambient sites. However, the correlation between fixed site measurements and exposure of individual persons to air contaminants is likely to be weak.

Materials and methods

We measured particulate matter both outdoors and indoors by following the spatial movement of individuals. Sixteen test persons took part and carried a measurement backpack for a 24-h period. The backpack was comprised of a Grimm Aerosol Spectrometer model 1.109, a GPS device, and a video camera for tracking of human behavior. The spectrometer provided information about particle numbers and mass in 32-size classes with a high temporal resolution of 6 s.

Results

The personal exposure of individuals during 24 h could significantly exceed the outdoor particulate matter (PM)₁₀ concentrations measured at the fixed sites. The average 24-h exposure of all test persons for PM₁₀ varied from 27 to 322 ??g m^?3. Environmental tobacco smoke and cooking emissions were among the main indoor sources for PM. The amount of particulate matter a test person was exposed to was highly dependent on the spatial behavior and the surrounding microenvironment conditions.

Discussion

Large-scale experiments including personal measurements might help to improve modeling approaches to approximate the actual exposure on a statistically sound basis.     

In situ photoelectrochemical/photocatalytic study of a dye discoloration in a microreactor system using TiO2 thin films

Introduction

In this work, we report in situ studies of UV photoelectrocatalytic discoloration of a dye (indigo carmine) by a TiO₂ thin film in a microreactor to demonstrate the driving force of the applied electrode potential and the dye flow rate toward dye discoloration kinetics.

Methods

TiO₂ 65-nm-thick thin films were deposited by PVD magnetron sputtering technique on a conducting glass substrate of fluorinated tin oxide. A microreactor to measure the discoloration rate, the electrode potential, and the photocurrent in situ, was developed. The dye solutions, before and after measurements in the microreactor, were analyzed by Raman spectroscopy.

Results

The annealed TiO₂ thin films had anatase structure with preferential orientation (101). The discoloration rate of the dye increased with the applied potential to TiO₂ electrode. Further, acceleration of the photocatalytic reaction was achieved by utilizing dye flow recirculation to the microreactor. In both cases the photoelectrochemical/photocatalytic discoloration kinetics of the dye follows the Langmuir?CHinshelwood model, with first-order kinetics.

Conclusions

The feasibility of dye discoloration on TiO₂ thin film electrodes, prepared by magnetron sputtering using a flow microreactor system, has been clearly demonstrated. The discoloration rate is enhanced by applying a positive potential (E _AP) and/or increasing the flow rate. The fastest discoloration and shortest irradiation time (50?min) produced 80% discoloration with an external anodic potential of 0.931?V and a flow rate of 12.2?mL?min^?1.     

Efficient biosorption of chromium(VI) ion by dry Araucaria leaves

Background

In this paper, batch removal of hexavalent chromium from aqueous solutions by Araucaria heterophylla leaves was investigated. The batch experiments were conducted to study the adsorption of metal species and effect of different pH, contact time, metal concentration, biosorbent concentration, and adsorption capacity.

Method

Freundlich and Langmuir??s isotherm model were used to describe the adsorption behavior, and the experimental results fitted Freundlich model well.

Results

The adsorption efficiency observed for all chromium concentrations, i.e., 1, 3, 5, and 10?mg/L was 100% and the equilibrium was achieved in 30?min for 1 and 3?mg/L, whereas for 5 and 10?mg/L, it was less than 60?min. FTIR spectra was taken to identify functional groups involved in the biosorption.

Conclusion

Thus, Araucaria leaves can be considered as one of the cheap and efficient biosorbent for toxic hexavalent chromium removal from natural or wastewaters.     

Effects of phosphorus amendments and plant growth on the mobility of Pb, Cu, and Zn in a multi-metal-contaminated soil

Purpose

Phosphorus amendments have been widely and successfully used in immobilization of one single metal (e.g., Pb) in contaminated soils. However, application of P amendments in the immobilization of multiple metals and particularly investigations about the effects of planting on the stability of the initially P-induced immobilized metals in the contaminated soils are far limited.

Methods

This study was conducted to determine the effects of phosphate rock tailing (PR), triple superphosphate fertilizer (TSP), and their combination (P+T) on mobility of Pb, Cu, and Zn in a multimetal-contaminated soil. Chinese cabbage (Brassica rapa subsp. chinensis) (metal-sensitive) and Chinese kale (Brassica alboglabra Bailey) (metal-resistant) were introduced to examine the effects of planting on leaching of Pb, Cu, and Zn in the P-amended soils.

Results

All three P treatments greatly reduced CaCl₂-extractable Pb and Zn by 55.2?C73.1% and 14.3?C33.6%, respectively. The PR treatment decreased CaCl₂-extractable Cu by 27.8%, while the TSP and P+T treatments increased it by 47.2% and 44.4%, respectively. All three P treatments were effective in reducing simulated rainwater leachable Pb, with dissolved and total leachable Pb decrease by 15.6?C81.9% and 16.3?C64.5%, respectively. The PR treatment reduced the total leachable Zn by 16.8%, while TSP and P+T treatments increased Zn leaching by 92.7% and 78.9%, respectively. However, total Cu leaching were elevated by 17.8?C178% in all P treatments. Planting promoted the leaching of Pb and Cu by 98.7?C127% and 23.5?C170%, respectively, especially in the colloid fraction, whereas the leachable Zn was reduced by 95.3?C96.5% due to planting. The P treatments reduced the uptake of Pb, Cu, and Zn in the aboveground parts of Chinese cabbage by up to 65.1%, 34.3%, and 9.59%, respectively. Though P treatments were effective in reducing Zn concentrations in the aboveground parts of the metal-resistant Chinese kale by 22.4?C28.9%, they had little effect on Pb and Cu uptake.

Conclusions

The results indicated that all P treatments were effective in immobilizing Pb. The effect on the immobilization of Cu and Zn varied with the different P treatments and evaluation methods. Metal-sensitive plants are more responsive to the P treatments than metal-resistant plants. Planting affects leaching of metals in the P-amended soils, specially leaching of colloid fraction. The conventional assessment on leaching risks of heavy metals by determining dissolved metals (filtered through 0.45-??m pore size membrane) in leachates could be underestimated since colloid fraction may also contribute to the leaching.     

Highly efficient decolorization of Malachite Green by a novel Micrococcus sp. strain BD15

Purpose

Malachite Green (MG) is used for a variety of applications but is also known to be carcinogenic and mutagenic. In this study, a novel Micrococcus sp. (strain BD15) was observed to efficiently decolorize MG. The purposes of this study were to explore the optimal conditions for decolorization and to evaluate the potential use of this strain for MG decolorization.

Methods

Optical microscope and UV?Cvisible analyses were carried out to determine whether the decolorization was due to biosorption or biodegradation. A Plackett?CBurman design was employed to investigate the effect of various parameters on decolorization, and response surface methodology was then used to explore the optimal decolorization conditions. Kinetics analysis and antimicrobial activity tests were also performed.

Results

The results indicated that the decolorization by the strain was mainly due to biodegradation. Concentrations of MG, urea, and yeast extract and inoculum size had significantly positive effects on MG decolorization, while concentrations of CuCl₂ and MgCl₂, and temperature had significantly negative effects. The interaction between different parameters could significantly affect decolorization, and the optimal conditions for decolorization were 1.0 g/L urea, 0.9 g/L yeast extract, 100 mg/L MG, 0.1 g/L inoculums (dry weight), and incubation at 25.2°C. Under the optimal conditions, 96.9% of MG was removed by the strain within 1 h, which represents highly efficient microbial decolorization. Moreover, the kinetic data for decolorization fit a second-order model well, and the strain showed a good MG detoxification capability.

Conclusion

Based on the results of this study, we propose Micrococcus sp. strain BD15 as an excellent candidate strain for MG removal from wastewater.     

Thirty-year amendment of horse manure and chemical fertilizer on the availability of micronutrients at the aggregate scale in black soil

Purpose

This study evaluates manure and chemical fertilizer effects on micronutrient (Fe, Mn, Cu, and Zn) content and availability in crops.

Methods

Seven treatments were selected, including three conventional fertilization treatments (NP, horse manure (M), and NP plus M (NPM)), three corresponding double rate fertilization (N2P2, M2, and N2P2M2), and a CK. Soil samples were collected and separated into four aggregates by wet-sieving in September 2009. Corn samples were collected and analyzed simultaneously.

Results

Treatment N2P2 increased DTPA extractable Fe, Mn, and Cu in soil by 732%, 388%, and 42%, whereas M2 decreased the corresponding values by 26%, 22%, and 10%, respectively, compared to CK. DTPA extractable Zn in soil and Zn in corn grain were higher in the M and M2 treatments than in the other treatments, and DTPA Zn was significantly correlated with soil organic carbon (SOC) in large macroaggregate, microaggregate, and silt + clay fractions. The Mn concentrations in corn stalks and grain were significantly correlated with DTPA extractable Mn in bulk soil and microaggregates, and Zn in stalks were significantly correlated with DTPA Zn in bulk soil, microaggregates, and large macroaggregates.

Conclusions

Long-term application of horse manure could increase soil Zn availability and uptake by corn, possibly due to its activation by SOC. In contrast, chemical fertilizer application increased DTPA extractable Fe, Mn, and Cu in soil by reducing soil pH. Our results also suggest that Mn uptake by corn originated mainly in microaggregates, whereas Zn in crops was primarily sourced from large macroaggregates and microaggregates.     

Synthesis, properties and application research of atrazine Fe3O4@SiO2 magnetic molecularly imprinted polymer

Introduction

Magnetic Fe₃O₄ nanoparticles were prepared by coprecipitation and then were coated with SiO₂ on the surface.

Materials and methods

Fe₃O₄@SiO₂ composite microspheres were modified by KH570. Using molecular imprinting technology, atrazine magnetic molecularly imprinted polymer was prepared by using atrazine as template molecule, methacrylic acid as functional monomer and ethylene glycol dimethacrylate as cross-linkers. The morphology, composition and magnetic properties of magnetic nanoparticles were characterized. The recognition selectivity of polymer was studied for template molecule and simulation by UV spectrophotometry. The adsorption properties and selectivity ability were analyzed by Scatchard analysis.

Results

Scatchard linear regression analysis indicated that there are two binding sites of the target molecules. The magnetic molecularly imprinted polymer has been applied to the analysis of atrazine in real samples.

Conclusion

The results show that: the recovery rates and the relative standard deviation were 94.0??98.7% and 2.1??4.0% in corn, the recovery rates and the relative standard deviation were 88.7??93.5% and 2.8??7.2% in water.     

Removal of Pb(II) and Cd(II) ions from water by Fe and Ag nanoparticles prepared using electro-exploding wire technique

Purpose

This work aimed at investigating the adsorption of lead and cadmium onto Fe and Ag nanoparticles for use as a water contaminant removal agent as a function of particle type, sorbent concentration, and contact time.

Methods

Fe and Ag spherical nanoparticles were prepared in water by the lab-made electro-exploding wire (EEW) system and were investigated for their structure properties. Adsorption experiments were carried out at room temperature and pH 8.3 water solutions.

Results

The removal/adsorption of both Pb(II) and Cd(II) ions was found to be dependent on adsorbent dosage and contact time. Pb(II) adsorption onto Fe and Ag nanoparticles showed more or less similar efficiency and behavior. The kinetic data for the adsorption process obeyed pseudo second-order rate equations. The calculated equilibrium adsorption capacities (q _e) were 813 and 800 mg/g for Pb sorption onto Fe and Ag nanoparticles, respectively. Cd(II) ion adsorption onto Fe nanoparticles obeyed pseudo second-order rate equations with q _e equal to 242 mg/g, while their adsorption onto Ag nanoparticles obeyed pseudo first-order rate equations with q _e of 794 mg/g. The calculated q _es are in quite agreement with the experimental values. The removal/uptake mechanisms of metal ions involved interaction between the metal ion and the oxide/hydroxyl layer around the spherical metallic core of the nanoparticle in water medium.

Conclusion

Fe and Ag nanoparticles prepared using the EEW technique exhibited high potentials for the removal of metal ions from water with very high adsorption capacities, suggesting that the EEW technique can be enlarged to generate nanoparticles with large quantities for field or site water purification.     

The effects of cerium on the growth and some antioxidant metabolisms in rice seedlings

Introduction

The aims of the present study are to investigate the effects of Ce³⁺ on the growth and some antioxidant metabolisms in rice seedlings (Oryza sativa L. cv Shengdao 16).

Materials and methods

The rice was treated with 0, 0.05, 0.1, 0.5, 1.0, and 1.5?mM Ce³⁺, respectively. The growth index of rice was measured. The chlorophyll content; catalase, superoxide dismutase, and peroxidase activities; and the level of hydrogen peroxide (H₂O₂), superoxide anion (O ₂ ^·? ), and malondialdehyde were assayed. The accumulation of Ce³⁺ and the uptake of mineral nutrition elements were analyzed with ICP-SF-MS.

Results and discussion

Hormetic effects of Ce³⁺ on the growth and some antioxidant metabolisms were found in the roots and shoots of rice. The roots can accumulate a much higher content of Ce³⁺ than shoots and Ce³⁺ mainly located in the cell wall of roots. Moreover, the uptake of K, Mg, Ca, Na, Fe, Mn, Zn, Cu, and Mo in the roots and shoots was affected with the exposure of different Ce³⁺ treatments, which indicated that Ce³⁺ affected the nutritional status of roots and shoots and further affected the growth of rice.

Conclusion

The appropriate amount of Ce³⁺ improved the defense system and growth of rice. The roots can accumulate a much higher content of Ce³⁺ than shoots. Moreover, the uptake of K, Mg, Ca, Na, Fe, Mn, Zn, Cu, and Mo in the roots and shoots was affected with the exposure of different Ce³⁺ treatments.     

Analysis and fit of surface CO2 concentrations at a rural site

Purpose

The impact of CO₂ urban plume in a rural area was investigated by concentrations recorded near surface.

Methods

CO₂ dry concentrations at three levels near surface were recorded for about 8 months at a rural site. Daily cycles were obtained and directional analysis was made with percentiles. Several functions were used to fit background and plume concentrations and the goodness of fit was evaluated with different statistics, which were also compared.

Results

Daily cycle showed a difference of around 2 ppm during the night between the lowest (1.8 m) and the highest (8.3 m) levels. Weighting functions of the directional analysis revealed the influence of the Valladolid urban plume. Two regions were established, with local factors prevailing below 3 m?s^?1 and transport dominating above 6 m?s^?1. The best fit was achieved with a quadratic function for the background and a cubic function for the plume due to the lack of symmetry observed. Gamma and Weibull distributions were also successfully used. Some statistics, such as the root mean square error (RMSE), stood out when evaluating the goodness of fit, whilst others were discarded due to their extremely low values and the lack of sensitivity against the functions used. Finally, a comprehensive metric merging several statistics was also tested with slight differences against RMSE.     

Synthesis of α-Fe2O3 nanofibers for applications in removal and recovery of Cr(VI) from wastewater

Purpose

Nanomaterials such as iron oxides and ferrites have been intensively investigated for water treatment and environmental remediation applications. The purpose of this work is to synthesize α-Fe₂O₃ nanofibers for potential applications in removal and recovery of noxious Cr(VI) from wastewater.

Methods

α-Fe₂O₃ nanofibers were synthesized via a simple hydrothermal route followed by calcination. The crystallographic structure and the morphology of the as-prepared α-Fe₂O₃ nanofibers were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope. Batch adsorption experiments were conducted, and Fourier transform infrared spectra were recorded before and after adsorption to investigate the Cr(VI) removal performance and adsorption mechanism. Langmuir and Freundlich modes were employed to analyze the adsorption behavior of Cr(VI) on the α-Fe₂O₃ nanofibers.

Results

Very thin and porous α-Fe₂O₃ nanofibers have been successfully synthesized for investigation of Cr(VI) removal capability from synthetic wastewater. Batch experiments revealed that the as-prepared α-Fe₂O₃ nanofibers exhibited excellent Cr(VI) removal performance with a maximum adsorption capacity of 16.17 mg g^?1. Furthermore, the adsorption capacity almost kept unchanged after recycling and reusing. The Cr(VI) adsorption process was found to follow the pseudo-second-order kinetics model, and the corresponding thermodynamic parameters ΔG°, ΔH°, and ΔS° at 298 K were calculated to be ?26.60 kJ?mol^?1, ?3.32 kJ?mol^?1, and 78.12 J?mol^?1 K^?1, respectively.

Conclusions

The as-prepared α-Fe₂O₃ nanofibers can be utilized as efficient low-cost nano-absorbents for removal and recovery of Cr(VI) from wastewater.     

The effects of elevated carbon dioxide levels on a Vibrio sp. isolated from the deep-sea

Introduction

The effect of oceanic CO₂ sequestration was examined exposing a deep-sea bacterium identified as Vibrio alginolyticus (9NA) to elevated levels of carbon dioxide and monitoring its growth at 2,750 psi (1,846 m depth).

Findings

The wild-type strain of 9NA could not grow in acidified marine broth below a pH of 5. The pH of marine broth did not drop below this level until at least 20.8 mM of CO₂ was injected into the medium. 9NA did not grow at this CO₂ concentration or higher concentrations (31.2 and 41.6 mM) for at least 72 h. Carbon dioxide at 10.4 mM also inhibited growth, but the bacterium was able to recover and grow. Exposure to CO₂ caused the cell to undergo a morphological change and form a dimple-like structure. The membrane was also damaged but with no protein leakage.     

Microbial structure and chemical components of aerosols caused by rotating brushes in a wastewater treatment plant

Purpose

Bacterial community structure and the chemical components in aerosols caused by rotating brushes in an Orbal oxidation ditch were assessed in a Beijing municipal wastewater treatment plant.

Methods

Air samples were collected at different distances from the aerosol-generating rotating brushes. Molecular culture-independent methods were used to characterize the community structure of the airborne bacteria in each sample regardless of cell culturability. A clone library of 16S rDNA directly amplified from air DNA of each sample was constructed and sequenced to analyze the community composition and diversity. Insoluble particles and water-soluble ions emitted with microorganisms in aerosols were analysis by a scanning electron microscope together with energy dispersive X-ray spectroscopy and ion chromatogram analyzer.

Results

In total, most of the identified bacteria were Proteobacteria. The majority of sequences near the rotating brushes (the main source of the bioaerosols) were Proteobacteria (62.97 %) with ??-(18.52 %) and ??-(44.45?%) subgroups and Bacteroidetes (29.63 %). Complex patterns were observed for each sampling location, suggesting a highly diverse community structure, comparable to that found in water in the Orbal oxidation ditch. Accompany with microorganisms, 46.36???g/m³ of SO ₄ ^2? , 29.35???g/m³ of Cl^?, 21.51???g/m³ of NO ₃ ^? , 19.76???g/m³ of NH ₄ ⁺ , 11.42???g/m³ of PO ₄ ^3? , 6.18???g/m³ of NO ₂ ^? , and elements of Mg, Cl, K, Na, Fe, S, and P were detected from the air near the aerosols source.

Conclusions

Differences in the structure of the bacterial communities and chemical components in the aerosols observed between sampling sites indicated important site-related variability. The composition of microorganisms in water was one of the most important sources of bacterial communities in bioaerosols. Chemical components in bioaerosols may provide a media for airborne microorganism attachment, as well as a suitable microenvironment for their growth and survival in the air. This study will be benefit for the formulation of pollution standards, especially for aerosols, that take into account plant workers?? health.     

Aquatic photochemistry of paracetamol in the presence of dissolved organic chromophoric material and nitrate

Purpose

This study contains some new findings connected to the photolysis of the drug paracetamol (hereinafter APAP) especially in light of estimating natural conditions, and it will offer information to better evaluate environmental problems connected with this widely used analgesic agent. Only a few studies, so far, have focussed on the photodegradation process of APAP in the natural environment, and the question about the role of the colored/chromophoric dissolved organic matter (CDOM) and nitrate (NO ₃ ^? ) as photoinductors is almost open.

Methods

APAP dissolved in freshwater and pure laboratory water in the presence and absence of CDOM and NO ₃ ^? ions was irradiated using weak-energy photon energies simulating natural conditions.

Results

CDOM and NO ₃ ^? as photoinductors produced only the slow phototransformation of APAP under weak energy radiation, and APAP seemed to be practically resistant to direct photolysis under weak radiant energies available in natural conditions. The estimated reaction efficiencies, in addition to half-lives, speak for that NO ₃ ^? and CDOM do not act as quite independent photoinductors but their effect in conjunction (CDOM?CNO ₃ ^? ?Cwater) is stronger than the separate ones. The principal phototransformation intermediates of APAP were mono-hydroxy derivatives, depending on available photon energies formed via ortho- or meta-hydroxylation, possessing substantial power of resistance to further specific transformation reactions.

Conclusions

The estimated half-life of the phototransformation of APAP in the natural aqueous environment and in the presence of suitable photoinductors will be about 30?days or more.     

Biodegradation of benzene, toluene, and xylene (BTX) in liquid culture and in soil by Bacillus subtilis and Pseudomonas aeruginosa strains and a formulated bacterial consortium

Purpose

The major aromatic constituents of petroleum products viz. benzene, toluene, and mixture of xylenes (BTX) are responsible for environmental pollution and inflict serious public concern. Therefore, BTX biodegradation potential of individual as well as formulated bacterial consortium was evaluated. This study highlighted the role of hydrogen peroxide (H₂O₂), nitrate, and phosphate in stimulating the biodegradation of BTX compounds under hypoxic condition.

Materials and methods

The individual bacterium viz. Bacillus subtilis DM-04 and Pseudomonas aeruginosa M and NM strains and a consortium comprising of the above bacteria were inoculated to BTX-containing liquid medium and in soil. The bioremediation experiment was carried out for 120?h in BTX-containing liquid culture and for 90?days in BTX-contaminated soil. The kinetics of BTX degradation either in presence or absence of H₂O₂, nitrate, and phosphate was analyzed using biochemical and gas chromatographic (GC) technique.

Results

Bacterial consortium was found to be superior in degrading BTX either in soil or in liquid medium as compared to degradation of same compounds by individual strains of the consortium. The rate of BTX biodegradation was further enhanced when the liquid medium/soil was exogenously supplemented with 0.01?% (v/v) H₂O₂, phosphate, and nitrate_. The GC analysis of BTX biodegradation (90?days post-inoculation) in soil by bacterial consortium confirmed the preferential degradation of benzene compared to m-xylene and toluene.

Conclusions

It may be concluded that the bacterial consortium in the present study can degrade BTX compounds at a significantly higher rate as compared to the degradation of the same compounds by individual members of the consortium. Further, addition of H₂O₂ in the culture medium as an additional source of oxygen, and nitrate and phosphate as an alternative electron acceptor and macronutrient, respectively, significantly enhanced the rate of BTX biodegradation under oxygen-limited condition.